| Age | Commit message (Collapse) | Author |
|---|
|
Add latest added DMA_CHAIN_DONE irq to QSPI_ALL_IRQS that encompasses all
of the qspi IRQs.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1690285689-30233-5-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After setting up dma descriptors and before initiaiting dma transfer, call
dma_wmb() to ensure all writes go through.
This doesn't fix any reported problem but is added for safety.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Fixes: b5762d95607e ("spi: spi-qcom-qspi: Add DMA mode support")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1690285689-30233-4-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
While allocating for DMA descriptor, GFP_KERNEL flag is being used and
this allocation happens within critical section with spinlock acquired.
This generates a static checker warning.
Use GFP_ATOMIC to prevent sleeping; and since this increases chances of
allocation failure, add handling accordingly.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/abc223e8-44af-40bb-a0bd-9865b393f435@moroto.mountain/
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Fixes: b5762d95607e ("spi: spi-qcom-qspi: Add DMA mode support")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1690285689-30233-3-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
During FIFO/DMA modes dynamic switching, only corresponding interrupts are
enabled. However its possible that FIFO related interrupt status registers
get set during DMA mode. For example WR_FIFO_EMPTY bit is set during DMA
TX.
Ignore such status bits so that they don't trip unwanted operations.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Fixes: b5762d95607e ("spi: spi-qcom-qspi: Add DMA mode support")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1690285689-30233-2-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fix from Geert Uytterhoeven:
- Fix the build when using the toolchain in Debian unstable.
* tag 'm68k-for-v6.5-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix invalid .section syntax
|
|
Reconcile devices.txt with serial/ucc_uart.c regarding device number
assignments. ucc_uart.c supports 4 ports and uses minor devnums
46-49, so update devices.txt with that info.
Then update ucc_uart.c's reference to the location of the devices.txt
list in the kernel source tree.
Fixes: d7584ed2b994 ("[POWERPC] qe-uart: add support for Freescale QUICCEngine UART")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Timur Tabi <timur@kernel.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-serial@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Link: https://lore.kernel.org/r/20230724063341.28198-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add mailing lists for linux-serial and lkml for the TTY layer. And let's
list the recently added files. This makes it easier for get_maintainer.pl
to include linux-serial for patches.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230721072334.59272-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In gsm_cleanup_mux() the 'gsm->dlci' pointer was not cleaned properly,
leaving it a dangling pointer after gsm_dlci_release.
This leads to use-after-free where 'gsm->dlci[0]' are freed and accessed
by the subsequent gsm_cleanup_mux().
Such is the case in the following call trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1e3/0x2cb lib/dump_stack.c:106
print_address_description+0x63/0x3b0 mm/kasan/report.c:248
__kasan_report mm/kasan/report.c:434 [inline]
kasan_report+0x16b/0x1c0 mm/kasan/report.c:451
gsm_cleanup_mux+0x76a/0x850 drivers/tty/n_gsm.c:2397
gsm_config drivers/tty/n_gsm.c:2653 [inline]
gsmld_ioctl+0xaae/0x15b0 drivers/tty/n_gsm.c:2986
tty_ioctl+0x8ff/0xc50 drivers/tty/tty_io.c:2816
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:874 [inline]
__se_sys_ioctl+0xf1/0x160 fs/ioctl.c:860
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x61/0xcb
</TASK>
Allocated by task 3501:
kasan_save_stack mm/kasan/common.c:38 [inline]
kasan_set_track mm/kasan/common.c:46 [inline]
set_alloc_info mm/kasan/common.c:434 [inline]
____kasan_kmalloc+0xba/0xf0 mm/kasan/common.c:513
kasan_kmalloc include/linux/kasan.h:264 [inline]
kmem_cache_alloc_trace+0x143/0x290 mm/slub.c:3247
kmalloc include/linux/slab.h:591 [inline]
kzalloc include/linux/slab.h:721 [inline]
gsm_dlci_alloc+0x53/0x3a0 drivers/tty/n_gsm.c:1932
gsm_activate_mux+0x1c/0x330 drivers/tty/n_gsm.c:2438
gsm_config drivers/tty/n_gsm.c:2677 [inline]
gsmld_ioctl+0xd46/0x15b0 drivers/tty/n_gsm.c:2986
tty_ioctl+0x8ff/0xc50 drivers/tty/tty_io.c:2816
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:874 [inline]
__se_sys_ioctl+0xf1/0x160 fs/ioctl.c:860
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x61/0xcb
Freed by task 3501:
kasan_save_stack mm/kasan/common.c:38 [inline]
kasan_set_track+0x4b/0x80 mm/kasan/common.c:46
kasan_set_free_info+0x1f/0x40 mm/kasan/generic.c:360
____kasan_slab_free+0xd8/0x120 mm/kasan/common.c:366
kasan_slab_free include/linux/kasan.h:230 [inline]
slab_free_hook mm/slub.c:1705 [inline]
slab_free_freelist_hook+0xdd/0x160 mm/slub.c:1731
slab_free mm/slub.c:3499 [inline]
kfree+0xf1/0x270 mm/slub.c:4559
dlci_put drivers/tty/n_gsm.c:1988 [inline]
gsm_dlci_release drivers/tty/n_gsm.c:2021 [inline]
gsm_cleanup_mux+0x574/0x850 drivers/tty/n_gsm.c:2415
gsm_config drivers/tty/n_gsm.c:2653 [inline]
gsmld_ioctl+0xaae/0x15b0 drivers/tty/n_gsm.c:2986
tty_ioctl+0x8ff/0xc50 drivers/tty/tty_io.c:2816
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:874 [inline]
__se_sys_ioctl+0xf1/0x160 fs/ioctl.c:860
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x61/0xcb
Fixes: aa371e96f05d ("tty: n_gsm: fix restart handling via CLD command")
Signed-off-by: Chaoyuan Peng <hedonistsmith@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using the cleaner policy to decommission the cache, there is
never any writeback started from the cache as it is constantly delayed
due to normal I/O keeping the device busy. Meaning @idle=false was
always being passed to clean_target_met()
Fix this by adding a specific 'cleaner' flag that is set when the
cleaner policy is configured. This flag serves to always allow the
cleaner's writeback work to be queued until the cache is
decommissioned (even if the cache isn't idle).
Reported-by: David Jeffery <djeffery@redhat.com>
Fixes: b29d4986d0da ("dm cache: significant rework to leverage dm-bio-prison-v2")
Cc: stable@vger.kernel.org
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
__md_stop_writes() and __md_stop() will modify many fields that are
protected by 'reconfig_mutex', and all the callers will grab
'reconfig_mutex' except for md_stop().
Also, update md_stop() to make certain 'reconfig_mutex' is held using
lockdep_assert_held().
Fixes: 9d09e663d550 ("dm: raid456 basic support")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
There are four equivalent goto tags in raid_ctr(), clean them up to
use just one.
There is no functional change and this is preparation to fix
raid_ctr()'s unprotected md_stop().
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
In the error paths 'bad_stripe_cache' and 'bad_check_reshape',
'reconfig_mutex' is still held after raid_ctr() returns.
Fixes: 9dbd1aa3a81c ("dm raid: add reshaping support to the target")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
If the statement "recalc_tags = kvmalloc(recalc_tags_size, GFP_NOIO);"
fails, we call "vfree(recalc_buffer)" and we jump to the label "oom".
If the condition "recalc_sectors >= 1U << ic->sb->log2_sectors_per_block"
is false, we jump to the label "free_ret" and call "vfree(recalc_buffer)"
again, on an already released memory block.
Fix the bug by setting "recalc_buffer = NULL" after freeing it.
Fixes: da8b4fc1f63a ("dm integrity: only allocate recalculate buffer when needed")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Previously, the cdns3_gadget_check_config() function in the cdns3 driver
mistakenly calculated the ep_buf_size by considering only one
configuration's endpoint information because "claimed" will be clear after
call usb_gadget_check_config().
The fix involves checking the private flags EP_CLAIMED instead of relying
on the "claimed" flag.
Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230707230015.494999-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The legacy gadget driver omitted calling usb_gadget_check_config()
to ensure that the USB device controller (UDC) has adequate resources,
including sufficient endpoint numbers and types, to support the given
configuration.
Previously, usb_add_config() was solely invoked by the legacy gadget
driver. Adds the necessary usb_gadget_check_config() after the bind()
operation to fix the issue.
Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230707230015.494999-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The buffer address used in sysfs_emit should be aligned to PAGE_SIZE.
Use sysfs_emit_at instead to offset the buffer.
Fixes: a7cff92f0635 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pointers of each usb_power_delivery handles are stored in "pds"
array returned from the pd_get ops but not in the adjacent memory
calculated from "pd". Get the handles from "pds" array directly instead
of deriving them from "pd".
Fixes: a7cff92f0635 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When calling device_add in the registration of typec_port, it will do
the NULL check on usb_power_delivery handle in typec_port for the
visibility of the device attributes. It is always NULL because port->pd
is set in typec_port_set_usb_power_delivery which is later than the
device_add call.
Set port->pd before device_add and only link the device after that.
Fixes: a7cff92f0635 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230623151036.3955013-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
device_get_named_child_node() returns NULL, if it fails, replace
IS_ERR() with NULL pointer check.
Fixes: a4422ff22142 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230725125319.565733-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tegra_xudc_powerdomain_init()"
This reverts commit f08aa7c80dac27ee00fa6827f447597d2fba5465.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this driver, the bug means that probe cannot succeed when CONFIG_PM
is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: f08aa7c80dac ("usb: gadget: tegra-xudc: Fix error check in tegra_xudc_powerdomain_init()")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/ZKQoBa84U/ykEh3C@moroto
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 18fc7c435be3f17ea26a21b2e2312fcb9088e01f.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this code, the patch means that certain tegra_xusb_probe() will
fail if the firmware supports power-domains but CONFIG_PM is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 18fc7c435be3 ("usb: xhci: tegra: Fix error check")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/8baace8d-fb4b-41a4-ad5f-848ae643a23b@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, increasing raw_dev->count happens before invoke the
raw_queue_event(), if the raw_queue_event() return error, invoke
raw_release() will not trigger the dev_free() to be called.
[ 268.905865][ T5067] raw-gadget.0 gadget.0: failed to queue event
[ 268.912053][ T5067] udc dummy_udc.0: failed to start USB Raw Gadget: -12
[ 268.918885][ T5067] raw-gadget.0: probe of gadget.0 failed with error -12
[ 268.925956][ T5067] UDC core: USB Raw Gadget: couldn't find an available UDC or it's busy
[ 268.934657][ T5067] misc raw-gadget: fail, usb_gadget_register_driver returned -16
BUG: memory leak
[<ffffffff8154bf94>] kmalloc_trace+0x24/0x90 mm/slab_common.c:1076
[<ffffffff8347eb55>] kmalloc include/linux/slab.h:582 [inline]
[<ffffffff8347eb55>] kzalloc include/linux/slab.h:703 [inline]
[<ffffffff8347eb55>] dev_new drivers/usb/gadget/legacy/raw_gadget.c:191 [inline]
[<ffffffff8347eb55>] raw_open+0x45/0x110 drivers/usb/gadget/legacy/raw_gadget.c:385
[<ffffffff827d1d09>] misc_open+0x1a9/0x1f0 drivers/char/misc.c:165
[<ffffffff8154bf94>] kmalloc_trace+0x24/0x90 mm/slab_common.c:1076
[<ffffffff8347cd2f>] kmalloc include/linux/slab.h:582 [inline]
[<ffffffff8347cd2f>] raw_ioctl_init+0xdf/0x410 drivers/usb/gadget/legacy/raw_gadget.c:460
[<ffffffff8347dfe9>] raw_ioctl+0x5f9/0x1120 drivers/usb/gadget/legacy/raw_gadget.c:1250
[<ffffffff81685173>] vfs_ioctl fs/ioctl.c:51 [inline]
[<ffffffff8154bf94>] kmalloc_trace+0x24/0x90 mm/slab_common.c:1076
[<ffffffff833ecc6a>] kmalloc include/linux/slab.h:582 [inline]
[<ffffffff833ecc6a>] kzalloc include/linux/slab.h:703 [inline]
[<ffffffff833ecc6a>] dummy_alloc_request+0x5a/0xe0 drivers/usb/gadget/udc/dummy_hcd.c:665
[<ffffffff833e9132>] usb_ep_alloc_request+0x22/0xd0 drivers/usb/gadget/udc/core.c:196
[<ffffffff8347f13d>] gadget_bind+0x6d/0x370 drivers/usb/gadget/legacy/raw_gadget.c:292
This commit therefore invoke kref_get() under the condition that
raw_queue_event() return success.
Reported-by: syzbot+feb045d335c1fdde5bf7@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Closes: https://syzkaller.appspot.com/bug?extid=feb045d335c1fdde5bf7
Signed-off-by: Zqiang <qiang.zhang1211@gmail.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/20230714074011.20989-1-qiang.zhang1211@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 286d9975a838 ("usb: gadget: udc: core: Prevent soft_connect_store() race")
introduced one extra mutex_unlock of connect_lock in the usb_gadget_active function.
Fixes: 286d9975a838 ("usb: gadget: udc: core: Prevent soft_connect_store() race")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230721222256.1743645-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit b138e23d3dff90c0494925b4c1874227b81bddf7.
AutoRetry has been found to sometimes cause controller freezes when
communicating with buggy USB devices.
This controller feature allows the controller in host mode to send
non-terminating/burst retry ACKs instead of terminating retry ACKs
to devices when a transaction error (CRC error or overflow) occurs.
Unfortunately, if the USB device continues to respond with a CRC error,
the controller will not complete endpoint-related commands while it
keeps trying to auto-retry. [3] The xHCI driver will notice this once
it tries to abort the transfer using a Stop Endpoint command and
does not receive a completion in time. [1]
This situation is reported to dmesg:
[sda] tag#29 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[sda] tag#29 CDB: opcode=0x28 28 00 00 69 42 80 00 00 48 00
xhci-hcd: xHCI host not responding to stop endpoint command
xhci-hcd: xHCI host controller not responding, assume dead
xhci-hcd: HC died; cleaning up
Some users observed this problem on an Odroid HC2 with the JMS578
USB3-to-SATA bridge. The issue can be triggered by starting
a read-heavy workload on an attached SSD. After a while, the host
controller would die and the SSD would disappear from the system. [1]
Further analysis by Synopsys determined that controller revisions
other than the one in Odroid HC2 are also affected by this.
The recommended solution was to disable AutoRetry altogether.
This change does not have a noticeable performance impact. [2]
Revert the enablement commit. This will keep the AutoRetry bit in
the default state configured during SoC design [2].
Fixes: b138e23d3dff ("usb: dwc3: core: Enable AutoRetry feature in the controller")
Link: https://lore.kernel.org/r/a21f34c04632d250cd0a78c7c6f4a1c9c7a43142.camel@gmail.com/ [1]
Link: https://lore.kernel.org/r/20230711214834.kyr6ulync32d4ktk@synopsys.com/ [2]
Link: https://lore.kernel.org/r/20230712225518.2smu7wse6djc7l5o@synopsys.com/ [3]
Cc: stable@vger.kernel.org
Cc: Mauro Ribeiro <mauro.ribeiro@hardkernel.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jakub Vanek <linuxtardis@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230714122419.27741-1-linuxtardis@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 5255660b208aebfdb71d574f3952cf48392f4306.
This quirk breaks at least the following hardware:
0b:00.0 0c03: 1106:3483 (rev 01) (prog-if 30 [XHCI])
Subsystem: 1106:3483
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 66
Region 0: Memory at fb400000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/4 Maskable- 64bit+
Address: 00000000fee007b8 Data: 0000
Capabilities: [c4] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 89W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <2us, L1 <16us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range B, TimeoutDis+ NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
with the quirk enabled it fails early with
[ 0.754373] pci 0000:0b:00.0: xHCI HW did not halt within 32000 usec status = 0x1000
[ 0.754419] pci 0000:0b:00.0: quirk_usb_early_handoff+0x0/0x7a0 took 31459 usecs
[ 2.228048] xhci_hcd 0000:0b:00.0: xHCI Host Controller
[ 2.228053] xhci_hcd 0000:0b:00.0: new USB bus registered, assigned bus number 7
[ 2.260073] xhci_hcd 0000:0b:00.0: Host halt failed, -110
[ 2.260079] xhci_hcd 0000:0b:00.0: can't setup: -110
[ 2.260551] xhci_hcd 0000:0b:00.0: USB bus 7 deregistered
[ 2.260624] xhci_hcd 0000:0b:00.0: init 0000:0b:00.0 fail, -110
[ 2.260639] xhci_hcd: probe of 0000:0b:00.0 failed with error -110
The hardware in question is an external PCIe card. It looks to me like the quirk
needs to be narrowed down. But this needs information about the hardware showing
the issue this quirk is to fix. So for now a clean revert.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 5255660b208a ("xhci: add quirk for host controllers that don't update endpoint DCS")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230713112830.21773-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Focusrite Scarlett audio device does not behave correctly during
resumes. Below is what happens during every resume (captured with
Beagle 5000):
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset/Target disconnected>
<High Speed>
The Scarlett disconnects and is enumerated again.
However from time to time it drops completely off the USB bus during
resume. Below is captured occurrence of such an event:
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset>/<Chirp K>/<Tiny K>
<High Speed>
<Corrupted packet>
<Reset/Target disconnected>
To fix the condition a user has to unplug and plug the device again.
With USB_QUIRK_RESET_RESUME applied ("usbcore.quirks=1235:8211:b")
for the Scarlett audio device the issue still reproduces.
Applying USB_QUIRK_DISCONNECT_SUSPEND ("usbcore.quirks=1235:8211:m")
fixed the issue and the Scarlett audio device didn't drop off the USB
bus for ~5000 suspend/resume cycles where originally issue reproduced in
~100 or less suspend/resume cycles.
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230724112911.1802577-1-lb@semihalf.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow devices to have dma operations beyond 64K, and avoid warnings such
as:
DMA-API: xhci-mtk 11200000.usb: mapping sg segment longer than device claims to support [len=98304] [max=65536]
Fixes: 0cbd4b34cda9 ("xhci: mediatek: support MTK xHCI host controller")
Cc: stable <stable@kernel.org>
Tested-by: Zubin Mithra <zsm@chromium.org>
Reported-by: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20230628-mtk-usb-v2-1-c8c34eb9f229@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Alternate working e-mail of this Reviewer not available
so drop it do prevent unnecessary bounce backs.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230712122828.17793-1-rogerq@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on
system_suspend in host mode") replaces check for HOST only dr_mode with
current_dr_role. But during booting, the current_dr_role isn't
initialized, thus the device side reset is always issued even if dwc3
was configured as host-only. What's more, on some platforms with host
only dwc3, aways issuing device side reset by accessing device register
block can cause kernel panic.
Fixes: c4a5153e87fd ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230627162018.739-1-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ucsi_unregister_partner()
It's better to set TYPEC_STATE_SAFE mode from ucsi_unregister_partner()
instead of ucsi_partner_change(), ucsi_unregister_partner() is always
when the partner disconnects.
Fixes: 25a2bc21c863 ("usb: typec: ucsi: call typec_set_mode on non-altmode partner change")
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230626-topic-sm8550-usb-c-audio-fixup-v1-1-bc72fddf3f42@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ohci_hcd_at91_drv_suspend() sets ohci->rh_state to OHCI_RH_HALTED when
suspend which will let the ohci_irq() skip the interrupt after resume. And
nobody to handle this interrupt.
According to the comment in ohci_hcd_at91_drv_suspend(), it need to reset
when resume from suspend(MEM) to fix by setting "hibernated" argument of
ohci_resume().
Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230626152713.18950-1-aarongt.shen@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The same way we already do in xenbus_init.
Fixes the following warning:
[ 352.175563] Trying to free already-free IRQ 0
[ 352.177355] WARNING: CPU: 1 PID: 88 at kernel/irq/manage.c:1893 free_irq+0xbf/0x350
[...]
[ 352.213951] Call Trace:
[ 352.214390] <TASK>
[ 352.214717] ? __warn+0x81/0x170
[ 352.215436] ? free_irq+0xbf/0x350
[ 352.215906] ? report_bug+0x10b/0x200
[ 352.216408] ? prb_read_valid+0x17/0x20
[ 352.216926] ? handle_bug+0x44/0x80
[ 352.217409] ? exc_invalid_op+0x13/0x60
[ 352.217932] ? asm_exc_invalid_op+0x16/0x20
[ 352.218497] ? free_irq+0xbf/0x350
[ 352.218979] ? __pfx_xenbus_probe_thread+0x10/0x10
[ 352.219600] xenbus_probe+0x7a/0x80
[ 352.221030] xenbus_probe_thread+0x76/0xc0
Fixes: 5b3353949e89 ("xen: add support for initializing xenstore later as HVM domain")
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2307211609140.3118466@ubuntu-linux-20-04-desktop
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.5-rc4
Here are some new modem device ids and a new "simple" driver for a CAN
bus device.
Included is also a patch sorting the "simple" driver entries in order to
make it more obvious where new ones should be added.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.5-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: simple: sort driver entries
USB: serial: simple: add Kaufmann RKS+CAN VCP
USB: serial: option: add Quectel EC200A module support
USB: serial: option: support Quectel EM060K_128
|
|
Pass i2c_client to _pmbus_is_enabled to drop the assumption
that a regulator device is passed in.
This will fix the issue of a NULL pointer dereference when called from
_pmbus_get_flags.
Fixes: df5f6b6af01c ("hwmon: (pmbus/core) Generalise pmbus get status")
Cc: stable@vger.kernel.org # v6.4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230725125428.3966803-2-Naresh.Solanki@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Refactor pmbus_is_enabled() to return the status without any additional
processing as it is already done in _pmbus_is_enabled().
Fixes: df5f6b6af01c ("hwmon: (pmbus/core) Generalise pmbus get status")
Cc: stable@vger.kernel.org # v6.4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230725125428.3966803-1-Naresh.Solanki@9elements.com
[groeck: Rephrased commit message]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Currently huawei-wmi causes a lot of spam in dmesg on my
Huawei MateBook X Pro 2022:
...
[36409.328463] input input9: Unknown key pressed, code: 0x02c1
[36411.335104] input input9: Unknown key pressed, code: 0x02c1
[36412.338674] input input9: Unknown key pressed, code: 0x02c1
[36414.848564] input input9: Unknown key pressed, code: 0x02c1
[36416.858706] input input9: Unknown key pressed, code: 0x02c1
...
Fix that by ignoring events generated by ambient light sensor.
This issue was reported on GitHub and resolved with the following merge
request:
https://github.com/aymanbagabas/Huawei-WMI/pull/70
I've contacted the mainter of this repo and he gave me the "go ahead" to
send this patch to the maling list.
Signed-off-by: Konstantin Shelekhin <k.shelekhin@ftml.net>
Link: https://lore.kernel.org/r/20230722155922.173856-1-k.shelekhin@ftml.net
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Only the HW rfkill state is toggled on laptops with quirks->ec_read_only
(so far only MSI Wind U90/U100). There are, however, a few issues with
the implementation:
1. The initial HW state is always unblocked, regardless of the actual
state on boot, because msi_init_rfkill only sets the SW state,
regardless of ec_read_only.
2. The initial SW state corresponds to the actual state on boot, but it
can't be changed afterwards, because set_device_state returns
-EOPNOTSUPP. It confuses the userspace, making Wi-Fi and/or Bluetooth
unusable if it was blocked on boot, and breaking the airplane mode if
the rfkill was unblocked on boot.
Address the above issues by properly initializing the HW state on
ec_read_only laptops and by allowing the userspace to toggle the SW
state. Don't set the SW state ourselves and let the userspace fully
control it. Toggling the SW state is a no-op, however, it allows the
userspace to properly toggle the airplane mode. The actual SW radio
disablement is handled by the corresponding rtl818x_pci and btusb
drivers that have their own rfkills.
Tested on MSI Wind U100 Plus, BIOS ver 1.0G, EC ver 130.
Fixes: 0816392b97d4 ("msi-laptop: merge quirk tables to one")
Fixes: 0de6575ad0a8 ("msi-laptop: Add MSI Wind U90/U100 support")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Link: https://lore.kernel.org/r/20230721145423.161057-1-maxtram95@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This patch fixes setting the cmd values to 0xb3 and 0xb4.
This is necessary on some TUF laptops in order to set the RGB mode.
Closes: https://lore.kernel.org/platform-driver-x86/443078148.491022.1677576298133@nm83.abv.bg
Signed-off-by: Kristian Angelov <kristiana2000@abv.bg>
Reviewed-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/ZLlS7o6UdTUBkyqa@wyvern.localdomain
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
key might contain private part of the key, so better use
kfree_sensitive to free it.
Signed-off-by: Wang Ming <machel@vivo.com>
Link: https://lore.kernel.org/r/20230717101114.18966-1-machel@vivo.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
HP Elite Dragonfly G2 (a convertible laptop/tablet) has a reliable VGBS
method. If VGBS is not called on boot, the firmware sends an initial
0xcd event shortly after calling the BTNL method, but only if the device
is booted in the laptop mode. However, if the device is booted in the
tablet mode and VGBS is not called, there is no initial 0xcc event, and
the input device for SW_TABLET_MODE is not registered up until the user
turns the device into the laptop mode.
Call VGBS on boot on this device to get the initial state of
SW_TABLET_MODE in a reliable way.
Tested with BIOS 1.13.1.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Link: https://lore.kernel.org/r/20230716183213.64173-1-maxtram95@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
On a HP Elite Dragonfly G2 the 0xcc and 0xcd events for SW_TABLET_MODE
are only send after the BTNL ACPI method has been called.
Likely more devices need this, so make the BTNL ACPI method unconditional
instead of only doing it on devices with a 5 button array.
Note this also makes the intel_button_array_enable() call in probe()
unconditional, that function does its own priv->array check. This makes
the intel_button_array_enable() call in probe() consistent with the calls
done on suspend/resume which also rely on the priv->array check inside
the function.
Reported-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Closes: https://lore.kernel.org/platform-driver-x86/20230712175023.31651-1-maxtram95@gmail.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230715181516.5173-1-hdegoede@redhat.com
|
|
APMF fn8 can notify EC about the OS slider position change. Add this
capability to the PMF driver so that it can call the APMF fn8 based on
the changes in the Platform profile events.
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20230714144435.1239776-2-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
apmf_get_system_params() failure is not a critical event, reduce its
verbosity from dev_err to dev_dbg.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20230714144435.1239776-1-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Microsoft Modern Wireless Headset (appearing on the host as "Microsoft
USB Link") has a playback and a capture mixer volume/switch, but they
are fairly broken. The descriptor reports wrong dB ranges for
playback, and the capture volume/switch don't influence on the actual
recording at all. Moreover, there seem instabilities in the
connection, and at best, we should disable the runtime PM.
So this ended up with a quirk entry for:
- Correct the playback dB range;
I picked up some reasonable values but it's a guess work
- Disable the capture mixer;
it's completely useless and confuses PA/PW
- Suppress get-sample-rate, apply the delay for message handling,
and suppress the auto-suspend
The behavior of the wheel control on the headset is somehow flaky,
too, but it's an issue of HID.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1207129
Link: https://lore.kernel.org/r/20230725092057.15115-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This HP Notebook used ALC236 codec with COEF 0x07 idx 1 controlling
the mute LED. Enable already existing quirk for this device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230725111509.623773-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The 8K sample parameter of 12.288Mhz main system bus clock doesn't work
because the I2SC_MR.IMCKDIV must not be 0 according to the sama5d2
series datasheet(I2SC Mode Register of Register Summary).
So use the 6.144Mhz instead of 12.288Mhz to support 8K sample.
Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Link: https://lore.kernel.org/r/20230715030620.62328-1-aarongt.shen@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the system suspends, peripheral SDCA interrupts are disabled.
When system level resume is invoked, the peripheral SDCA interrupts
should be enabled to handle JD events.
Enable SDCA interrupts in resume sequence when ClockStop Mode0 is applied.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090711.128247-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the system suspends, peripheral Imp-defined interrupt is disabled.
When system level resume is invoked, the peripheral Imp-defined interrupts
should be enabled to handle JD events.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090654.128230-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the system suspends, peripheral SDCA interrupts are disabled.
When system level resume is invoked, the peripheral SDCA interrupts
should be enabled to handle JD events.
Enable SDCA interrupts in resume sequence when ClockStop Mode0 is applied.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090732.128282-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the system suspends, peripheral SDCA interrupts are disabled.
When system level resume is invoked, the peripheral SDCA interrupts
should be enabled to handle JD events.
Enable SDCA interrupts in resume sequence when ClockStop Mode0 is applied.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090721.128264-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
