| Age | Commit message (Collapse) | Author |
|---|
|
We need to store device offsets in 64 bit as the device
address space may be larger than the CPU's.
Fixes GPU init failures on radeons with 4GB or more of
vram on 32 bit kernels. We put vram at the start of the
GPU's address space so the gart aperture starts at 4 GB
causing all GPU addresses in the gart aperture to get
truncated.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=89072
[airlied: fix warning on nouveau build]
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: thellstrom@vmware.com
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The current implementation is limited by the number of addresses that
fit into an unsigned long. This causes problems on 32-bit Tegra where
unsigned long is 32-bit but drm_mm is used to manage an IOVA space of
4 GiB. Given the 32-bit limitation, the range is limited to 4 GiB - 1
(or 4 GiB - 4 KiB for page granularity).
This commit changes the start and size of the range to be an unsigned
64-bit integer, thus allowing much larger ranges to be supported.
[airlied: fix i915 warnings and coloring callback]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fixupo
|
|
Commit 8634b51f6ca2 (locks: convert lease handling to file_lock_context)
introduced a regression in the handling of lease upgrade/downgrades.
In the event that we already have a lease on a file and are going to
either upgrade or downgrade it, we skip doing any list insertion or
deletion and simply re-call lm_setup on the existing lease.
As of commit 8634b51f6ca2 however, we end up calling lm_setup on the
lease that was passed in, instead of on the existing lease. This causes
us to leak the fasync_struct that was allocated in the event that there
was not already an existing one (as it always appeared that there
wasn't one).
Fixes: 8634b51f6ca2 (locks: convert lease handling to file_lock_context)
Reported-and-Tested-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull eCryptfs fixes from Tyler Hicks:
"Fixes for proper ioctl handling and an untriggerable buffer overflow
- The eCryptfs ioctl handling functions should only pass known-good
ioctl commands to the lower filesystem
- A static checker found a potential buffer overflow. Upon
inspection, it is not triggerable due to input validation performed
on the mount parameters"
* tag 'ecryptfs-4.0-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: don't pass fs-specific ioctl commands through
eCryptfs: ensure copy to crypt_stat->cipher does not overrun
|
|
The irq line used by the PMC block is shared with several peripherals
including the init timer which is registering its handler with
IRQF_NO_SUSPEND.
Implement the appropriate suspend/resume callback for the PMC irqchip,
and inform irq core that PMC irq handler can be safely called while
the system is suspended by setting IRQF_COND_SUSPEND.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The IRQ line used by the RTC device is usually shared with the system
timer (PIT) on at91 platforms.
Since timers are registering their handlers with IRQF_NO_SUSPEND, we
should expect being called in suspended state, and properly wake the
system up when this is the case.
Set IRQF_COND_SUSPEND flag when registering the IRQ handler to inform
irq core that it can safely be called while the system is suspended.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The IRQ line used by the RTC device is usually shared with the system timer
(PIT) on at91 platforms.
Since timers are registering their handlers with IRQF_NO_SUSPEND, we should
expect being called in suspended state, and properly wake the system up
when this is the case.
Set IRQF_COND_SUSPEND flag when registering the IRQ handler to inform
irq core that it can safely be called while the system is suspended.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Export pm_system_wakeup function to allow irq handlers to deal with system
wakeup.
This is needed for shared IRQ lines where one of the handler is registered
with IRQF_NO_SUSPEND, while the other ones want to configure it as a wakeup
source.
In this specific case, irq core does not handle the wakeup process and
leave the decision to each irq handler.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When do suspend/resume stress test, some log shows "rcv is not +last".
The issue is that enet suspend will disable phy clock, phy link down,
after resume back, enet MAC redo initial and ready to tx/rx packet,
but phy still is not ready which is doing auto-negotiation. When phy
link is not up, don't schdule napi soft irq.
[Peter]
It has fixed kernel panic after long time suspend/resume test
with nfs rootfs.
[ 8864.429458] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.434799] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.440088] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.445424] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.450782] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.456111] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 8864.464225] pgd = 80004000
[ 8864.466997] [00000000] *pgd=00000000
[ 8864.470627] Internal error: Oops: 17 [#1] SMP ARM
[ 8864.475353] Modules linked in: evbug
[ 8864.479006] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.0.0-rc1-00044-g7a2a1d2 #234
[ 8864.486854] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[ 8864.492709] task: be069380 ti: be07a000 task.ti: be07a000
[ 8864.498137] PC is at memcpy+0x80/0x330
[ 8864.501919] LR is at gro_pull_from_frag0+0x34/0xa8
[ 8864.506735] pc : [<802bb080>] lr : [<8057c204>] psr: 00000113
[ 8864.506735] sp : be07bbd4 ip : 00000010 fp : be07bc0c
[ 8864.518235] r10: 0000000e r9 : 00000000 r8 : 809c7754
[ 8864.523479] r7 : 809c7754 r6 : bb43c040 r5 : bd280cc0 r4 : 00000012
[ 8864.530025] r3 : 00000804 r2 : fffffff2 r1 : 00000000 r0 : bb43b83c
[ 8864.536575] Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 8864.543904] Control: 10c5387d Table: bd14c04a DAC: 00000015
[ 8864.549669] Process ksoftirqd/0 (pid: 3, stack limit = 0xbe07a210)
[ 8864.555869] Stack: (0xbe07bbd4 to 0xbe07c000)
[ 8864.560250] bbc0: bd280cc0 bb43c040 809c7754
[ 8864.568455] bbe0: 809c7754 bb43b83c 00000012 8057c204 00000000 bd280cc0 bd8a0718 00000003
[ 8864.576658] bc00: be07bc5c be07bc10 8057ebf0 8057c1dc 00000000 00000000 8057ecc4 bef59760
[ 8864.584863] bc20: 00000002 bd8a0000 be07bc64 809c7754 00000000 bd8a0718 bd280cc0 bd8a0000
[ 8864.593066] bc40: 00000000 0000001c 00000000 bd8a0000 be07bc74 be07bc60 8057f148 8057eb90
[ 8864.601268] bc60: bf0810a0 00000000 be07bcf4 be07bc78 8044e7b4 8057f12c 00000000 8007df6c
[ 8864.609470] bc80: bd8a0718 00000040 00000000 bd280a80 00000002 00000019 bd8a0600 bd8a1214
[ 8864.617672] bca0: bd8a0690 bf0810a0 00000000 00000000 bd8a1000 00000000 00000027 bd280cc0
[ 8864.625874] bcc0: 80062708 800625cc 000943db bd8a0718 00000001 000d1166 00000040 be7c1ec0
[ 8864.634077] bce0: 0000012c be07bd00 be07bd3c be07bcf8 8057fc98 8044e3ac 809c2ec0 3ddff000
[ 8864.642280] bd00: be07bd00 be07bd00 be07bd08 be07bd08 00000000 00000020 809c608c 00000003
[ 8864.650481] bd20: 809c6080 40000001 809c6088 00200100 be07bd84 be07bd40 8002e690 8057fac8
[ 8864.658684] bd40: be07bd64 be07bd50 00000001 04208040 000d1165 0000000a be07bd84 809c0d7c
[ 8864.666885] bd60: 00000000 809c6af8 00000000 00000001 be008000 00000000 be07bd9c be07bd88
[ 8864.675087] bd80: 8002eb64 8002e564 00000125 809c0d7c be07bdc4 be07bda0 8006f100 8002eaac
[ 8864.683291] bda0: c080e10c be07bde8 809c6c6c c080e100 00000002 00000000 be07bde4 be07bdc8
[ 8864.691492] bdc0: 800087a0 8006f098 806f2934 20000013 ffffffff be07be1c be07be44 be07bde8
[ 8864.699695] bde0: 800133a4 80008784 00000001 00000001 00000000 00000000 be7c1680 00000000
[ 8864.707896] be00: be0cfe00 bd93eb40 00000002 00000000 00000000 be07be44 be07be00 be07be30
[ 8864.716098] be20: 8006278c 806f2934 20000013 ffffffff be069380 be7c1680 be07be7c be07be48
[ 8864.724300] be40: 80049cfc 806f2910 00000001 00000000 80049cb4 00000000 be07be7c be7c1680
[ 8864.732502] be60: be3289c0 be069380 bd23b600 be0cfe00 be07bebc be07be80 806ed614 80049c68
[ 8864.740706] be80: be07a000 0000020a 809c608c 00000003 00000001 8002e858 be07a000 be035740
[ 8864.748907] bea0: 00000000 00000001 809d4598 00000000 be07bed4 be07bec0 806edd0c 806ed440
[ 8864.757110] bec0: be07a000 be07a000 be07bee4 be07bed8 806edd68 806edcf0 be07bef4 be07bee8
[ 8864.765311] bee0: 8002e860 806edd34 be07bf24 be07bef8 800494b0 8002e828 be069380 00000000
[ 8864.773512] bf00: be035780 be035740 8004938c 00000000 00000000 00000000 be07bfac be07bf28
[ 8864.781715] bf20: 80045928 80049398 be07bf44 00000001 00000000 be035740 00000000 00030003
[ 8864.789917] bf40: dead4ead ffffffff ffffffff 80a2716c 80b59b00 00000000 8088c954 be07bf5c
[ 8864.798120] bf60: be07bf5c 00000000 00000000 dead4ead ffffffff ffffffff 80a2716c 00000000
[ 8864.806320] bf80: 00000000 8088c954 be07bf88 be07bf88 be035780 8004584c 00000000 00000000
[ 8864.814523] bfa0: 00000000 be07bfb0 8000ed10 80045858 00000000 00000000 00000000 00000000
[ 8864.822723] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 8864.830925] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 5ffbb5f7 f9fcf5e7
[ 8864.839115] Backtrace:
[ 8864.841631] [<8057c1d0>] (gro_pull_from_frag0) from [<8057ebf0>] (dev_gro_receive+0x6c/0x3f8)
[ 8864.850173] r6:00000003 r5:bd8a0718 r4:bd280cc0 r3:00000000
[ 8864.855958] [<8057eb84>] (dev_gro_receive) from [<8057f148>] (napi_gro_receive+0x28/0xac)
[ 8864.864152] r10:bd8a0000 r9:00000000 r8:0000001c r7:00000000 r6:bd8a0000 r5:bd280cc0
[ 8864.872115] r4:bd8a0718
[ 8864.874713] [<8057f120>] (napi_gro_receive) from [<8044e7b4>] (fec_enet_rx_napi+0x414/0xc74)
[ 8864.883167] r5:00000000 r4:bf0810a0
[ 8864.886823] [<8044e3a0>] (fec_enet_rx_napi) from [<8057fc98>] (net_rx_action+0x1dc/0x2ec)
[ 8864.895016] r10:be07bd00 r9:0000012c r8:be7c1ec0 r7:00000040 r6:000d1166 r5:00000001
[ 8864.902982] r4:bd8a0718
[ 8864.905570] [<8057fabc>] (net_rx_action) from [<8002e690>] (__do_softirq+0x138/0x2c4)
[ 8864.913417] r10:00200100 r9:809c6088 r8:40000001 r7:809c6080 r6:00000003 r5:809c608c
[ 8864.921382] r4:00000020
[ 8864.923966] [<8002e558>] (__do_softirq) from [<8002eb64>] (irq_exit+0xc4/0x138)
[ 8864.931289] r10:00000000 r9:be008000 r8:00000001 r7:00000000 r6:809c6af8 r5:00000000
[ 8864.939252] r4:809c0d7c
[ 8864.941841] [<8002eaa0>] (irq_exit) from [<8006f100>] (__handle_domain_irq+0x74/0xe8)
[ 8864.949688] r4:809c0d7c r3:00000125
[ 8864.953342] [<8006f08c>] (__handle_domain_irq) from [<800087a0>] (gic_handle_irq+0x28/0x68)
[ 8864.961707] r9:00000000 r8:00000002 r7:c080e100 r6:809c6c6c r5:be07bde8 r4:c080e10c
[ 8864.969597] [<80008778>] (gic_handle_irq) from [<800133a4>] (__irq_svc+0x44/0x5c)
[ 8864.977097] Exception stack(0xbe07bde8 to 0xbe07be30)
[ 8864.982173] bde0: 00000001 00000001 00000000 00000000 be7c1680 00000000
[ 8864.990377] be00: be0cfe00 bd93eb40 00000002 00000000 00000000 be07be44 be07be00 be07be30
[ 8864.998573] be20: 8006278c 806f2934 20000013 ffffffff
[ 8865.003638] r7:be07be1c r6:ffffffff r5:20000013 r4:806f2934
[ 8865.009447] [<806f2904>] (_raw_spin_unlock_irq) from [<80049cfc>] (finish_task_switch+0xa0/0x160)
[ 8865.018334] r4:be7c1680 r3:be069380
[ 8865.021993] [<80049c5c>] (finish_task_switch) from [<806ed614>] (__schedule+0x1e0/0x5dc)
[ 8865.030098] r8:be0cfe00 r7:bd23b600 r6:be069380 r5:be3289c0 r4:be7c1680
[ 8865.036942] [<806ed434>] (__schedule) from [<806edd0c>] (preempt_schedule_common+0x28/0x44)
[ 8865.045307] r9:00000000 r8:809d4598 r7:00000001 r6:00000000 r5:be035740 r4:be07a000
[ 8865.053197] [<806edce4>] (preempt_schedule_common) from [<806edd68>] (_cond_resched+0x40/0x48)
[ 8865.061822] r4:be07a000 r3:be07a000
[ 8865.065472] [<806edd28>] (_cond_resched) from [<8002e860>] (run_ksoftirqd+0x44/0x64)
[ 8865.073252] [<8002e81c>] (run_ksoftirqd) from [<800494b0>] (smpboot_thread_fn+0x124/0x190)
[ 8865.081550] [<8004938c>] (smpboot_thread_fn) from [<80045928>] (kthread+0xdc/0xf8)
[ 8865.089133] r10:00000000 r9:00000000 r8:00000000 r7:8004938c r6:be035740 r5:be035780
[ 8865.097097] r4:00000000 r3:be069380
[ 8865.100752] [<8004584c>] (kthread) from [<8000ed10>] (ret_from_fork+0x14/0x24)
[ 8865.107990] r7:00000000 r6:00000000 r5:8004584c r4:be035780
[ 8865.113767] Code: e320f000 e4913004 e4914004 e4915004 (e4916004)
[ 8865.120006] ---[ end trace b0a4c6bd499288ca ]---
[ 8865.124697] Kernel panic - not syncing: Fatal exception in interrupt
[ 8865.131084] ---[ end Kernel panic - not syncing: Fatal exception in interrupt
Cc: [v3.19+] stable@vger.kernel.org
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Iyappan Subramanian says:
====================
drivers: net: xgene: Fix backward compatibility of newer firmware with older kernel
Kernel 3.17 driver supports only RGMII ethernet interface.
Since the Tianocore DT contains same compatibility string for RGMII,
SGMII based 1G and XFI based 10G interfaces, crash happens when probe called
on SGMII based 1G and XFI based 10G interface.
This patch fixes the backward compatibility of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.
v2: Address comments from v1
* updated cover letter subject line with net: xgene
* Documentation: formatted compatible string values as list
v1:
* Initial version
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the backward compatibile of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the backward compatibility of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.
The new bindings are in sync with the newer firmware.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. For an IPv4 ping socket, ping_check_bind_addr does not check
the family of the socket address that's passed in. Instead,
make it behave like inet_bind, which enforces either that the
address family is AF_INET, or that the family is AF_UNSPEC and
the address is 0.0.0.0.
2. For an IPv6 ping socket, ping_check_bind_addr returns EINVAL
if the socket family is not AF_INET6. Return EAFNOSUPPORT
instead, for consistency with inet6_bind.
3. Make ping_v4_sendmsg and ping_v6_sendmsg return EAFNOSUPPORT
instead of EINVAL if an incorrect socket address structure is
passed in.
4. Make IPv6 ping sockets be IPv6-only. The code does not support
IPv4, and it cannot easily be made to support IPv4 because
the protocol numbers for ICMP and ICMPv6 are different. This
makes connect(::ffff:192.0.2.1) fail with EAFNOSUPPORT instead
of making the socket unusable.
Among other things, this fixes an oops that can be triggered by:
int s = socket(AF_INET, SOCK_DGRAM, IPPROTO_ICMP);
struct sockaddr_in6 sin6 = {
.sin6_family = AF_INET6,
.sin6_addr = in6addr_any,
};
bind(s, (struct sockaddr *) &sin6, sizeof(sin6));
Change-Id: If06ca86d9f1e4593c0d6df174caca3487c57a241
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case there was some tx buffer reclaimed and not enough rx packets
to consume the whole budget, napi_complete would not be called and
interrupts would be kept disabled, effectively resulting in the
network core never to call the poll callback again and no rx/tx
interrupts to be fired either.
Fix that by only accounting the rx work done in the poll callback.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we're getting IRQs after lots of resources are already
allocated:
* netdev
* clocks
* MDIO bus
Also HW gets initialized by the time when checking IRQs as well.
Now there's a possibility for master interrupt controller to be not
probed yet. This will lead to exit from GMAC probe routine with "-
EPROBE_DEFER" and so deferred probe will hapen later on.
But since we exited the first GMAC probe without release of all
allocated resources there could be conflicts on subsequent probes.
For example this is what happens for me:
--->8---
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 20005c7a at 1 IRQ POLL (stmmac-0:01) active
platform e0018000.ethernet: Driver stmmaceth requests probe deferral
...
...
...
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x4e/0x68()
sysfs: cannot create duplicate filename
'/devices/platform/axs10x_mb/e0018000.ethernet/mdio_bus/stmmac-0'
CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.0.0-rc1-next-20150303+#8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
sysfs_warn_dup+0x4e/0x68
sysfs_create_dir_ns+0x98/0xa0
kobject_add_internal+0x8c/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at lib/kobject.c:240
kobject_add_internal+0x218/0x2e8()
kobject_add_internal failed for stmmac-0 with -EEXIST, don't try to
register things with the same name in the same di.
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W
4.0.0-rc1-next-20150303+ #8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
kobject_add_internal+0x218/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be2 ]---
libphy: mii_bus stmmac-0 failed to register
: Cannot register as MDIO bus
stmmac_pltfr_probe: main driver probe failed
stmmaceth: probe of e0018000.ethernet failed with error -22
--->8---
Essential fix is to check for IRQs availability as early as possible and
then safely go to deferred probe if IRQs are not there yet.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
It currently is required that all users of NO_SUSPEND interrupt
lines pass the IRQF_NO_SUSPEND flag when requesting the IRQ or the
WARN_ON_ONCE() in irq_pm_install_action() will trigger. That is
done to warn about situations in which unprepared interrupt handlers
may be run unnecessarily for suspended devices and may attempt to
access those devices by mistake. However, it may cause drivers
that have no technical reasons for using IRQF_NO_SUSPEND to set
that flag just because they happen to share the interrupt line
with something like a timer.
Moreover, the generic handling of wakeup interrupts introduced by
commit 9ce7a25849e8 (genirq: Simplify wakeup mechanism) only works
for IRQs without any NO_SUSPEND users, so the drivers of wakeup
devices needing to use shared NO_SUSPEND interrupt lines for
signaling system wakeup generally have to detect wakeup in their
interrupt handlers. Thus if they happen to share an interrupt line
with a NO_SUSPEND user, they also need to request that their
interrupt handlers be run after suspend_device_irqs().
In both cases the reason for using IRQF_NO_SUSPEND is not because
the driver in question has a genuine need to run its interrupt
handler after suspend_device_irqs(), but because it happens to
share the line with some other NO_SUSPEND user. Otherwise, the
driver would do without IRQF_NO_SUSPEND just fine.
To make it possible to specify that condition explicitly, introduce
a new IRQ action handler flag for shared IRQs, IRQF_COND_SUSPEND,
that, when set, will indicate to the IRQ core that the interrupt
user is generally fine with suspending the IRQ, but it also can
tolerate handler invocations after suspend_device_irqs() and, in
particular, it is capable of detecting system wakeup and triggering
it as appropriate from its interrupt handler.
That will allow us to work around a problem with a shared timer
interrupt line on at91 platforms.
Link: http://marc.info/?l=linux-kernel&m=142252777602084&w=2
Link: http://marc.info/?t=142252775300011&r=1&w=2
Link: https://lkml.org/lkml/2014/12/15/552
Reported-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf
Pull dma-buf fixes from Sumit Semwal:
"Minor timeout & other fixes on reservation/fence"
* tag 'dma-buf-for-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
reservation: Remove shadowing local variable 'ret'
dma-buf/fence: don't wait when specified timeout is zero
reservation: wait only with non-zero timeout specified (v3)
|
|
Pull KVM fixes from Marcelo Tosatti:
"KVM bug fixes, including a SVM interrupt injection regression fix,
MIPS and ARM bug fixes"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MIPS: Enable after disabling interrupt
KVM: MIPS: Fix trace event to save PC directly
KVM: SVM: fix interrupt injection (apic->isr_count always 0)
KVM: emulate: fix CMPXCHG8B on 32-bit hosts
KVM: VMX: fix build without CONFIG_SMP
arm/arm64: KVM: Add exit reaons to kvm_exit event tracing
ARM: KVM: Fix size check in __coherent_cache_guest_page
|
|
In general, if a transaction object is added to the list successfully,
we can rely on the abort path to undo what we've done. This allows us to
simplify the error handling of the rule replacement path in
nf_tables_newrule().
This implicitly fixes an unnecessary removal of the old rule, which
needs to be left in place if we fail to replace.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The NFT_USERDATA_MAXLEN is defined to 256, however we only have a u8
to store its size. Introduce a struct nft_userdata which contains a
length field and indicate its presence using a single bit in the rule.
The length field of struct nft_userdata is also a u8, however we don't
store zero sized data, so the actual length is udata->len + 1.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Check that the space required for the expressions doesn't exceed the
size of the dlen field, which would lead to the iterators crashing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
A race condition exists in the rule transaction code for rules that
get added and removed within the same transaction.
The new rule starts out as inactive in the current and active in the
next generation and is inserted into the ruleset. When it is deleted,
it is additionally set to inactive in the next generation as well.
On commit the next generation is begun, then the actions are finalized.
For the new rule this would mean clearing out the inactive bit for
the previously current, now next generation.
However nft_rule_clear() clears out the bits for *both* generations,
activating the rule in the current generation, where it should be
deactivated due to being deleted. The rule will thus be active until
the deletion is finalized, removing the rule from the ruleset.
Similarly, when aborting a transaction for the same case, the undo
of insertion will remove it from the RCU protected rule list, the
deletion will clear out all bits. However until the next RCU
synchronization after all operations have been undone, the rule is
active on CPUs which can still see the rule on the list.
Generally, there may never be any modifications of the current
generations' inactive bit since this defeats the entire purpose of
atomicity. Change nft_rule_clear() to only touch the next generations
bit to fix this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- Fix for /proc/<pid>/maps "stack" vma annotation
- sched stats not printing correct sleeping task PC
- perf not reporting page faults
* tag 'arc-4.0-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix thread_saved_pc()
ARC: Fix KSTK_ESP()
ARC: perf: Enable generic software events
ARC: Make arc_unwind_core accessible externally
|
|
DMA_BIT_MASK of 64 is not valid dma address mask for OMAPs, it should be
set to 32.
The 64 was introduced by commit (in 2009):
a152ff24b978 ASoC: OMAP: Make DMA 64 aligned
But the dma_mask and coherent_dma_mask can not be used to specify alignment.
Fixes: a152ff24b978 (ASoC: OMAP: Make DMA 64 aligned)
Reported-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- Fix for dynticks.
- Fix for smpboot bug.
- Fix for IOMMU group refcounting.
* tag 'powerpc-4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/iommu: Remove IOMMU device references via bus notifier
powerpc/smp: Wait until secondaries are active & online
powerpc: Re-enable dynticks
|
|
In seq_buf_vprintf(), vsnprintf() is used to copy the format into the
buffer remaining in the seq_buf structure. The return of vsnprintf()
is the amount of characters written to the buffer excluding the '\0',
unless the line was truncated!
If the line copied does not fit, it is truncated, and a '\0' is added
to the end of the buffer. But in this case, '\0' is included in the length
of the line written. To know if the buffer had overflowed, the return
length will be the same as the length of the buffer passed in.
The check in seq_buf_vprintf() only checked if the length returned from
vsnprintf() would fit in the buffer, as the seq_buf_vprintf() is only
to be an all or nothing command. It either writes all the string into
the seq_buf, or none of it. If the string is truncated, the pointers
inside the seq_buf must be reset to what they were when the function was
called. This is not the case. On overflow, it copies only part of the string.
The fix is to change the overflow check to see if the length returned from
vsnprintf() is less than the length remaining in the seq_buf buffer, and not
if it is less than or equal to as it currently does. Then seq_buf_vprintf()
will know if the write from vsnpritnf() was truncated or not.
Cc: stable@vger.kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Report the actual error code from acpi_bus_register_driver(), it may
help future debugging (typically ENODEV as previously reported, but the
unusual cases are where it may help most).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
i915.ko depends upon the acpi/video.ko module and so refuses to load if
ACPI is disabled at runtime if for example the BIOS is broken beyond
repair. acpi/video provides an optional service for i915.ko and so we
should just allow the modules to load, but do no nothing in order to let
the machines boot correctly.
Reported-by: Bill Augur <bill-auger@programmer.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Acked-by: Aaron Lu <aaron.lu@intel.com>
[ rjw: Fixed up the new comment in acpi_video_init() ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To keep consisitency with the rest of the file, use 'genpd' as the
name of the 'struct generic_pm_domain' pointer instead of 'gpd'.
This is just a rename, no functional changes.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If CONFIG_SMP=n, <linux/smp.h> does not include <asm/smp.h>, causing:
drivers/cpufreq/ppc-corenet-cpufreq.c: In function 'corenet_cpufreq_cpu_init':
drivers/cpufreq/ppc-corenet-cpufreq.c:173:3: error: implicit declaration of function 'get_hard_smp_processor_id' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some BIOSes report incorrect length for ACPI address space descriptors,
so relax the checks to avoid regressions. This issue has appeared several
times as:
3162b6f0c5e1 ("PNPACPI: truncate _CRS windows with _LEN > _MAX - _MIN + 1")
d558b483d5a7 ("x86/PCI: truncate _CRS windows with _LEN > _MAX - _MIN + 1")
f238b414a74a ("PNPACPI: compute Address Space length rather than using _LEN")
48728e077480 ("x86/PCI: compute Address Space length rather than using _LEN")
Please refer to https://bugzilla.kernel.org/show_bug.cgi?id=94221
for more details and example malformed ACPI resource descriptors.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=94221
Fixes: 593669c2ac0f (x86/PCI/ACPI: Use common ACPI resource interfaces ...)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Dave Airlie <airlied@redhat.com>
Tested-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When parsing resources for PCI host bridge, we should ignore resources
consumed by host bridge itself and only report window resources available
to child PCI busses.
Fixes: 593669c2ac0f (x86/PCI/ACPI: Use common ACPI resource interfaces ...)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Below are the refinements.
1. Set DMA abort bit when disabling dma channel. This will clear
the remaining data in dma FIFO, to fix channel-swap issue.
2. Read DMA HW pointer when updating DMA status. Previously dma
position is calculated by adding one period size in dma interrupt.
This is inaccurate/insufficient for some high-quality audio APP.
Since interrupt bottom half handler has variable schedule delay,
it causes big error when calculating sample delay. Read the actual
HW pointer and feedback can improve the accuracy.
3. Do some minor code clean.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The commit [39f802d6b6d9: 'regulator: Build sysfs entries with static
attribute groups'] converted the sysfs entry creation to static
attribute groups, but this resulted in a regression due to the NULL
check of rdev->constraints. At the point where the device is
registered, rdev->constraints isn't set, so the attributes depending
on it are missing.
We may fix it by shuffling the code order in regulator_register(), but
a quicker fix is to just remove this NULL check. rdev->constraints is
in anyway always set to non-NULL in set_machine_constraints(), thus
the check there is basically superfluous.
Fixes: 39f802d6b6d9 ('regulator: Build sysfs entries with static attribute groups')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reportded-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With patch "include guest facilities in kvm facility test" it is no
longer necessary to have special handling for the non-LPAR case.
Signed-off-by: Michael Mueller <mimu@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
Most facility related decisions in KVM have to take into account:
- the facilities offered by the underlying run container (LPAR/VM)
- the facilities supported by the KVM code itself
- the facilities requested by a guest VM
This patch adds the KVM driver requested facilities to the test routine.
It additionally renames struct s390_model_fac to kvm_s390_fac and its field
names to be more meaningful.
The semantics of the facilities stored in the KVM architecture structure
is changed. The address arch.model.fac->list now points to the guest
facility list and arch.model.fac->mask points to the KVM facility mask.
This patch fixes the behaviour of KVM for some facilities for guests
that ignore the guest visible facility bits, e.g. guests could use
transactional memory intructions on hosts supporting them even if the
chosen cpu model would not offer them.
The userspace interface is not affected by this change.
Signed-off-by: Michael Mueller <mimu@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
