| Age | Commit message (Collapse) | Author |
|---|
|
Pull networking fixes from David Miller:
1) Use after free and new device IDs in bluetooth from Andre Guedes,
Yevgeniy Melnichuk, Gustavo Padovan, and Henrik Rydberg.
2) Fix crashes with short packet lengths and VLAN in pktgen, from
Nishank Trivedi.
3) mISDN calls flush_work_sync() with locks held, fix from Karsten
Keil.
4) Packet scheduler gred parameters are reported to userspace
improperly scaled, and WRED idling is not performed correctly. All
from David Ward.
5) Fix TCP socket refcount problem in ipv6, from Julian Anastasov.
6) ibmveth device has RX queue alignment requirements which are not
being explicitly met resulting in sporadic failures, fix from
Santiago Leon.
7) Netfilter needs to take care when interpreting sockets attached to
socket buffers, they could be time-wait minisockets. Fix from Eric
Dumazet.
8) sock_edemux() has the same issue as netfilter did in #7 above, fix
from Eric Dumazet.
9) Avoid infinite loops in CBQ scheduler with some configurations, from
Eric Dumazet.
10) Deal with "Reflection scan: an Off-Path Attack on TCP", from Jozsef
Kadlecsik.
11) SCTP overcharges socket for TX packets, fix from Thomas Graf.
12) CODEL packet scheduler should not reset it's state every time it
builds a new flow, fix from Eric Dumazet.
13) Fix memory leak in nl80211, from Wei Yongjun.
14) NETROM doesn't check skb_copy_datagram_iovec() return values, from
Alan Cox.
15) l2tp ethernet was using sizeof(ETH_HLEN) instead of plain ETH_HLEN,
oops. From Eric Dumazet.
16) Fix selection of ath9k chips on which PA linearization and AM2PM
predistoration are used, from Felix Fietkau.
17) Flow steering settings in mlx4 driver need to be validated properly,
from Hadar Hen Zion.
18) bnx2x doesn't show the correct link duplex setting, from Yaniv
Rosner.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
pktgen: fix crash with vlan and packet size less than 46
bnx2x: Add missing afex code
bnx2x: fix registers dumped
bnx2x: correct advertisement of pause capabilities
bnx2x: display the correct duplex value
bnx2x: prevent timeouts when using PFC
bnx2x: fix stats copying logic
bnx2x: Avoid sending multiple statistics queries
net: qmi_wwan: call subdriver with control intf only
net_sched: gred: actually perform idling in WRED mode
net_sched: gred: fix qave reporting via netlink
net_sched: gred: eliminate redundant DP prio comparisons
net_sched: gred: correct comment about qavg calculation in RIO mode
mISDN: Fix wrong usage of flush_work_sync while holding locks
netfilter: log: Fix log-level processing
net-sched: sch_cbq: avoid infinite loop
net: qmi_wwan: fix Gobi device probing for un2430
net: fix net/core/sock.c build error
ixp4xx_hss: fix build failure due to missing linux/module.h inclusion
caif: move the dereference below the NULL test
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are a number of USB patches, a bit more than I normally like this
late in the -rc series, but given people's vacations (myself
included), and the kernel summit, it seems to have happened this way.
All are tiny, but they add up. A number of gadget and xhci fixes, and
a few new device ids. All have been tested in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: don't stall endpoint if request list is empty in isr_tr_complete_low
usb: chipidea: cleanup dma_pool if udc_start() fails
usb: chipidea: udc: fix error path in udc_start()
usb: chipidea: udc: add pullup fuction, needed by the uvc gadget
usb: chipidea: udc: fix setup of endpoint maxpacket size
USB: option: replace ZTE K5006-Z entry with vendor class rule
EHCI: Update qTD next pointer in QH overlay region during unlink
USB: cdc-wdm: fix wdm_find_device* return value
USB: ftdi_sio: do not claim CDC ACM function
usb: dwc3: gadget: fix pending isoc handling
usb: renesas_usbhs: fixup DMA transport data alignment
usb: gadget: at91udc: Don't check for ep->ep.desc
usb: gadget: at91udc: don't overwrite driver data
usb: dwc3: core: fix incorrect usage of resource pointer
usb: musb: musbhsdma: fix IRQ check
usb: musb: tusb6010: fix error path in tusb_probe()
usb: musb: host: fix for musb_start_urb Oops
usb: gadget: dummy_hcd: add support for USB_DT_BOS on rh
usb: gadget: dummy_hcd: fixup error probe path
usb: gadget: s3c-hsotg.c: fix error return code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fixes from Greg Kroah-Hartman:
"Here are 2 tiny patches for a serial driver to resolve issues that
people have reported with the 3.6-rc tree.
Both of these have been in the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: imx: don't reinit clock in imx_setup_ufcr()
tty: serial: imx: console write routing is unsafe on SMP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are a few staging tree fixes for problems that have been
reported.
Nothing major, just a number of tiny driver fixes. All of these have
been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
drm/omap: add more new timings fields
drm/omap: update for interlaced
staging: r8712u: fix bug in r8712_recv_indicatepkt()
staging: zcache: fix cleancache race condition with shrinker
Staging: Android alarm: IOCTL command encoding fix
staging: vt6656: [BUG] - Failed connection, incorrect endian.
staging: ozwpan: fix memcmp() test in oz_set_active_pd()
staging: wlan-ng: Fix problem with wrong arguments
staging: comedi: das08: Correct AO output for das08jr-16-ao
staging: comedi: das08: Correct AI encoding for das08jr-16-ao
staging: comedi: das08: Fix PCI ref count
staging: comedi: amplc_pci230: Fix PCI ref count
staging: comedi: amplc_pc263: Fix PCI ref count
staging: comedi: amplc_pc236: Fix PCI ref count
staging: comedi: amplc_dio200: Fix PCI ref count
staging: comedi: amplc_pci224: Fix PCI ref count
drivers/iio/adc/at91_adc.c: adjust inconsistent IS_ERR and PTR_ERR
staging iio: fix potential memory leak in lis3l02dq_ring.c
staging:iio: prevent divide by zero bugs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg Kroah-Hartman:
"Here is one fix for 3.6-rc6 for the kobject.h file.
It fixes a reported oops if CONFIG_HOTPLUG is disabled. It's been in
the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: fix oops with "input0: bad kobj_uevent_env content in show_uevent()"
|
|
We already use them for openat() and friends, but fstat() also wants to
be able to use O_PATH file descriptors. This should make it more
directly comparable to the O_SEARCH of Solaris.
Note that you could already do the same thing with "fstatat()" and an
empty path, but just doing "fstat()" directly is simpler and faster, so
there is no reason not to just allow it directly.
See also commit 332a2e1244bd, which did the same thing for fchdir, for
the same reasons.
Reported-by: ольга крыжановская <olga.kryzhanovska@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org # O_PATH introduced in 3.0+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit a606dac368eed5696fb38e16b1394f1d049c09e9 adds support to link
devices which have _PRx, if a device does not have _PRx, a warning
message will be printed.
This commit is for ZPODD on Intel ZPODD capable platforms, on other
platforms, it has no problem if there is no power resource for this
device, so a warning here is not appropriate, change it to debug.
Reported-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Add DT property to tell the TPS6586x that it should provide the
pm_power_off() implementation. This allows "shutdown" to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Harmony uses a TPS6586x regulator. Instantiate this, and hook up a
couple of fixed GPIO-controlled regulators too.
Based on Ventana regulator patch by Stephen Warren <swarren@nvidia.com>
and converted to Harmony.
swarren made the following changes:
* Added ldo0 regulator configuration to device tree, and updated
board-harmony-pcie.c for the new regulator name.
* Fixed vdd_1v05's voltage from 10.5V to 1.05V.
* Modified board-harmony-pcie.c to obtain the en_vdd_1v05 GPIO number at
run-time from device tree instead of hard-coding it.
* Removed board-harmony{-power.c,.h} now that they're unused.
* Disabled vdd_1v05 regulator; the code in board-harmony-pcie.c hijacks
this GPIO for now. This will be fixed when the PCIe driver is re-
written as a driver. The code can't regulator_get("vdd_1v05") right
now, because the vdd_1v05 regulator's probe gets deferred due to its
supply being the PMIC, which gets probed after the regulator the first
time around, and this dependency is only resolved by repeated probing,
which happens when deferred_probe_initcall() is called, which happens
in a late initcall, whose runtime order relative to harmony_pcie_init()
is undefined, since that's also called from a late initcall.
* Removed unused harmony_pcie_initcall().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Harmony can be booted using device tree with equal functionality as when
booted using a board file. Remove as much of the board file as is
possible, since it's no longer needed.
Two special-cases are still left in board-dt-tegra20.c, since the Tegra
PCIe driver doesn't support device tree yet, and the Harmony .dts file
doesn't yet describe regulators which are needed for PCIe. This logic is
now enabled unconditionally rather than via CONFIG_MACH_HARMONY. While
this is more code than other boards, it's still unlikely to be much of a
problem, and both regulators and PCIe should be supported via device tree
in the near future, allowing the remaining code to be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Paz00 (Toshiba AC100) can be booted using device tree with equal
functionality as when booted using a board file. Remove as much of the
board file as is possible, since it's no longer needed.
One special-case is still left in board-dt-tegra20.c, since there is no
way to create a WiFi rfkill device from device tree yet. This logic is
now enabled unconditionally rather than via CONFIG_MACH_PAZ00. The extra
cases where it's enabled (.configs which did not enable Paz00 support)
shouldn't impact much since the amount of code is tiny.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Marc Dietrich <marvin24@gmx.de>
|
|
TrimSlice can be booted using device tree with equal functionality as
when booted using a board file. Remove the board file since it's no
longer needed.
One special-case is still left in board-dt-tegra20.c, since the Tegra
PCIe driver doesn't support device tree yet. This logic is now enabled
by CONFIG_TEGRA_PCI rather than via CONFIG_MACH_TRIMSLICE. The extra
cases where it's enabled (.configs which did not enable TrimSlice
support) shouldn't impact much since the amount of code is tiny.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
|
|
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
After calling into the lower filesystem to do a rename, the lower target
inode's attributes were not copied up to the eCryptfs target inode. This
resulted in the eCryptfs target inode staying around, rather than being
evicted, because i_nlink was not updated for the eCryptfs inode. This
also meant that eCryptfs didn't do the final iput() on the lower target
inode so it stayed around, as well. This would result in a failure to
free up space occupied by the target file in the rename() operation.
Both target inodes would eventually be evicted when the eCryptfs
filesystem was unmounted.
This patch calls fsstack_copy_attr_all() after the lower filesystem
does its ->rename() so that important inode attributes, such as i_nlink,
are updated at the eCryptfs layer. ecryptfs_evict_inode() is now called
and eCryptfs can drop its final reference on the lower inode.
http://launchpad.net/bugs/561129
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Cc: <stable@vger.kernel.org> [2.6.39+]
|
|
Since eCryptfs only calls fput() on the lower file in
ecryptfs_release(), eCryptfs should call the lower filesystem's
->flush() from ecryptfs_flush().
If the lower filesystem implements ->flush(), then eCryptfs should try
to flush out any dirty pages prior to calling the lower ->flush(). If
the lower filesystem does not implement ->flush(), then eCryptfs has no
need to do anything in ecryptfs_flush() since dirty pages are now
written out to the lower filesystem in ecryptfs_release().
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
|
|
Fixes a regression caused by:
821f749 eCryptfs: Revert to a writethrough cache model
That patch reverted some code (specifically, 32001d6f) that was
necessary to properly handle open() -> mmap() -> close() -> dirty pages
-> munmap(), because the lower file could be closed before the dirty
pages are written out.
Rather than reapplying 32001d6f, this approach is a better way of
ensuring that the lower file is still open in order to handle writing
out the dirty pages. It is called from ecryptfs_release(), while we have
a lock on the lower file pointer, just before the lower file gets the
final fput() and we overwrite the pointer.
https://launchpad.net/bugs/1047261
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reported-by: Artemy Tregubenko <me@arty.name>
Tested-by: Artemy Tregubenko <me@arty.name>
Tested-by: Colin Ian King <colin.king@canonical.com>
|
|
The code currently always selects turbo mode for PCA9665, no matter which
clock frequency is configured. This is because it compares the clock frequency
against constants reflecting (boundary / 100). Compare against real boundary
frequencies to fix the problem.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Guide people to where their patches can be found these days.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
|
|
We noticed a plymouth bug on Fedora 18, and I then
noticed this stupid thinko, fixing it fixed the problem
with plymouth.
Cc: stable@vger.kernel.org
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
into drm-fixes
Alex writes:
This is the current set of radeon fixes for 3.6. Two small fixes:
- fix the fence issues introduced in 3.5 with 64-bit fences
- PLL fix for multiple DP heads
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: make 64bit fences more robust v3
drm/radeon: rework pll selection (v3)
|
|
Commit 0090def("ACPI: Add interface to register/unregister device
to/from power resources") used resource_lock to protect the devices list
that relies on power resource. It caused a mutex dead lock, as below
acpi_power_on ---> lock resource_lock
__acpi_power_on
acpi_power_on_device
acpi_power_get_inferred_state
acpi_power_get_list_state ---> lock resource_lock
This patch adds a new mutex "devices_lock" to protect the devices list
and calls acpi_power_on_device in acpi_power_on, instead of
__acpi_power_on, after the resource_lock is released.
[rjw: Changed data type of a boolean variable to bool.]
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
It turns out that there are ACPI BIOSes defining device objects with
_PSx and without either _PSC or _PRx. For devices corresponding to
those ACPI objetcs __acpi_bus_get_power() returns ACPI_STATE_UNKNOWN
and their initial power states are regarded as unknown as a result.
If such a device is a parent of another power-manageable device, the
child cannot be put into a low-power state through ACPI, because
__acpi_bus_set_power() refuses to change power states of devices
whose parents' power states are unknown.
To work around this problem, observe that the ACPI power state of
a device cannot be higher-power (lower-number) than the power state
of its parent. Thus, if the device's _PSC method or the
configuration of its power resources indicates that the device is
in D0, the device's parent has to be in D0 as well. Consequently,
if the parent's power state is unknown when we've just learned that
its child's power state is D0, we can safely set the parent's
power.state field to ACPI_STATE_D0.
Tested-by: Aaron Lu <aaron.lu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
If vlan option is being specified in the pktgen and packet size
being requested is less than 46 bytes, despite being illogical
request, pktgen should not crash the kernel.
BUG: unable to handle kernel paging request at ffff88021fb82000
Process kpktgend_0 (pid: 1184, threadinfo ffff880215f1a000, task ffff880218544530)
Call Trace:
[<ffffffffa0637cd2>] ? pktgen_finalize_skb+0x222/0x300 [pktgen]
[<ffffffff814f0084>] ? build_skb+0x34/0x1c0
[<ffffffffa0639b11>] pktgen_thread_worker+0x5d1/0x1790 [pktgen]
[<ffffffffa03ffb10>] ? igb_xmit_frame_ring+0xa30/0xa30 [igb]
[<ffffffff8107ba20>] ? wake_up_bit+0x40/0x40
[<ffffffff8107ba20>] ? wake_up_bit+0x40/0x40
[<ffffffffa0639540>] ? spin+0x240/0x240 [pktgen]
[<ffffffff8107b4e3>] kthread+0x93/0xa0
[<ffffffff81615de4>] kernel_thread_helper+0x4/0x10
[<ffffffff8107b450>] ? flush_kthread_worker+0x80/0x80
[<ffffffff81615de0>] ? gs_change+0x13/0x13
The root cause of why pktgen is not able to handle this case is due
to comparison of signed (datalen) and unsigned data (sizeof), which
eventually passes a huge number to skb_put().
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The acpi_evalf() function modifies four bytes of data but in
fan_get_status() we pass a pointer to u8. I have modified the
function to use type checking now.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Fix a device reference count leakage issue in function
eeepc_rfkill_hotplug().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
MODULE_PARM_DESC for wlan_status is further in the same file
Signed-off-by: Maxim A. Nikulin <M.A.Nikulin@gmail.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=24222
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
This function fails to add the start address of the gmux I/O range to
the requested port address and thus writes to the wrong location.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Study of Apple's binary driver revealed that the GMUX_READ_PORT should
be written between calls to gmux_index_wait_ready and
gmux_index_wait_complete (i.e., the new index protocol must be
followed). If this is not done correctly, the indexed
gmux device only partially accepts writes which lead to problems
concerning GPU switching. Special thanks to Seth Forshee who helped
greatly with identifying unnecessary changes.
Signed-off-by: Bernhard Froemel <froemel@vmars.tuwien.ac.at>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
This patch extracts and displays version information from the indexed
gmux device as it is also done for the classic gmux device.
Signed-off-by: Bernhard Froemel <froemel@vmars.tuwien.ac.at>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Commit a334872224a67b614dc888460377862621f3dac7 added afex support but lacked
several logical changes. This lack can cause afex to crash, and also
have a slight effect on other flows (i.e., driver always assumes the Tx ring
has less available buffers than what it actually has).
This patch adds the missing segments, fixing said issues.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under traffic, there are several registers that when read (e.g., via
'ethtool -d') may cause the chip to stall.
This patch corrects the registers read in such flows.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch propagates users' requested flow-control into the link layer,
which will later be used to advertise this flow-control for auto-negotiation
(until now these values were ignored).
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to this fix, the driver reported the chip's active duplex state
is always 'full', even if using half-duplex mode.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent updating the xmac PFC configuration when using a link speed
slower than 10G -the umac block is responsible for 1G or slower connections,
therefore it is possible the xmac block is reset when connection is slower.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW needs the driver statistics for management. Current logic is broken
in that the function that gathers the port statistics does not copy
its own statistics to a place where the FW can use it.
This patch causes every function that can pass statistics to the FW to
do so.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During traffic when DCB is enabled, it is possible for multiple instances
of statistics queries to be sent to the chip - this may cause the FW to assert.
This patch prevents the sending of an additional instance of statistics query
while the previous query hasn't completed.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only increase the higher 32bits if we really detect a wrap around.
v2: instead of increasing the higher 32bits just use the higher
32bits from the last emitted fence.
v3: also use last emitted fence value as upper limit.
The intention of this patch is to make fences as robust as
they where before introducing 64bit fences. This is
necessary because on older systems it looks like the fence
value gets corrupted on initialization.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=51344
Should also fix:
https://bugs.freedesktop.org/show_bug.cgi?id=54129
https://bugs.freedesktop.org/show_bug.cgi?id=54662
https://bugzilla.redhat.com/show_bug.cgi?id=846505
https://bugzilla.redhat.com/show_bug.cgi?id=845639
3.5 needs a separate patch due to changes in the
fence code. Will send that out separately.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For DP we can use the same PPLL for all active DP
encoders. Take advantage of that to prevent cases
where we may end up sharing a PPLL between DP and
non-DP which won't work. Also clean up the code
a bit.
v2: - fix missing pll_id assignment in crtc init
v3: - fix DP PPLL check
- document functions
- break in main encoder search loop after matching.
no need to keep checking additional encoders.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=54471
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This fixes a hang on suspend due to calling wdm_suspend on
the unregistered data interface. The hang should have been
a NULL pointer reference had it not been for a logic error
in the cdc_wdm code.
commit 230718bd net: qmi_wwan: bind to both control and data interface
changed qmi_wwan to use cdc_wdm as a subdriver for devices with
a two-interface QMI/wwan function. The commit failed to update
qmi_wwan_suspend and qmi_wwan_resume, which were written to handle
either a single combined interface function, or no subdriver at all.
The result was that we called into the subdriver both when the
control interface was suspended and when the data interface was
suspended. Calling the subdriver suspend function with an
unregistered interface is not supported and will make the
subdriver bug out.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gred_dequeue() and gred_drop() do not seem to get called when the
queue is empty, meaning that we never start idling while in WRED
mode. And since qidlestart is not stored by gred_store_wred_set(),
we would never stop idling while in WRED mode if we ever started.
This messes up the average queue size calculation that influences
packet marking/dropping behavior.
Now, we start WRED mode idling as we are removing the last packet
from the queue. Also we now actually stop WRED mode idling when we
are enqueuing a packet.
Cc: Bruce Osler <brosler@cisco.com>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
q->vars.qavg is a Wlog scaled value, but q->backlog is not. In order
to pass q->vars.qavg as the backlog value, we need to un-scale it.
Additionally, the qave value returned via netlink should not be Wlog
scaled, so we need to un-scale the result of red_calc_qavg().
This caused artificially high values for "Average Queue" to be shown
by 'tc -s -d qdisc', but did not affect the actual operation of GRED.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each pair of DPs only needs to be compared once when searching for
a non-unique prio value.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is a bad idea to hold a spinlock and call flush_work_sync.
Move the workqueue cleanup outside the spinlock and use cancel_work_sync,
on closing the channel this seems to be the more correct function.
Remove the never used and constant return value of mISDN_freebchannel.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This board file has never been compiled. Let's just remove it
along with the one Kconfig reference to it in io.c.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
|
|
This is dead code that isn't initialized or setup (although it is
compiled). Remove it and the data structures it references.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
|
|
Using list_move_tail() instead of list_del() + list_add_tail().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David Brown <davidb@codeaurora.org>
|
