| Age | Commit message (Collapse) | Author |
|---|
|
commit 5d9a07b0de512b77bf28d2401e5fe3351f00a240 ("vhost: relax used
address alignment") fixed the alignment for the used virtual address,
but not for the physical address used for logging.
That's a mistake: alignment should clearly be the same for virtual and
physical addresses,
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
page reads
Every attempt to issue a read log page command lockup the controller.
The command is currently sent if the sata device includes the devlsp feature
to read out the timing data.
This attempt to read the data, locks up the controller and the device
is not recognzied correctly (failed to set xfermode) and cannot be accessed.
This was found on Freescale P1013/P1022 and T4240 CPUs
using a ATP IG mSATA 4GB with the devslp feature.
fsl-sata ff718000.sata: Sata FSL Platform/CSB Driver init
[ 1.254195] scsi0 : sata_fsl
[ 1.256004] ata1: SATA max UDMA/133 irq 74
[ 1.370666] fsl-gianfar ethernet.3: enabled errata workarounds, flags: 0x4
[ 1.470671] fsl-gianfar ethernet.4: enabled errata workarounds, flags: 0x4
[ 1.775584] ata1: Signature Update detected @ 504 msecs
[ 1.947594] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.948366] ata1.00: ATA-8: ATP IG mSATA, 20150311, max UDMA/133
[ 1.948371] ata1.00: 7732368 sectors, multi 0: LBA
[ 1.948843] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 1.948857] ata1.00: failed to set xfermode (err_mask=0x40)
[ 7.467557] ata1: Signature Update detected @ 504 msecs
[ 7.639560] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7.651320] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 7.651360] ata1.00: failed to set xfermode (err_mask=0x40)
[ 7.655628] ata1: limiting SATA link speed to 1.5 Gbps
[ 7.659458] ata1.00: limiting speed to UDMA/133:PIO3
[ 13.163554] ata1: Signature Update detected @ 504 msecs
[ 13.335558] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 13.347298] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 13.347334] ata1.00: failed to set xfermode (err_mask=0x40)
[ 13.351601] ata1.00: disabled
[ 13.353278] ata1: exception Emask 0x50 SAct 0x0 SErr 0x800 action 0x6 frozen t4
[ 13.359281] ata1: SError: { HostInt }
[ 13.361644] ata1: hard resetting link
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
log page
Some controller lockup on a ata_read_log_page.
Add new ata port flag ATA_FLAG_NO_LOG_PAGE which can used
to blacklist a controller.
If this flag is set, any attempt to read a log page returns an error
without actually issuing the command.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The following commit which went into mainline through networking tree
3b13758f51de ("cgroups: Allow dynamically changing net_classid")
conflicts in net/core/netclassid_cgroup.c with the following pending
fix in cgroup/for-4.4-fixes.
1f7dd3e5a6e4 ("cgroup: fix handling of multi-destination migration from subtree_control enabling")
The former separates out update_classid() from cgrp_attach() and
updates it to walk all fds of all tasks in the target css so that it
can be used from both migration and config change paths. The latter
drops @css from cgrp_attach().
Resolve the conflict by making cgrp_attach() call update_classid()
with the css from the first task. We can revive @tset walking in
cgrp_attach() but given that net_cls is v1 only where there always is
only one target css during migration, this is fine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Nina Schiff <ninasc@fb.com>
|
|
Once virtio starts using the DMA API, we won't be able to safely DMA
from the stack. virtio-net does a couple of config DMA requests
from small stack buffers -- switch to using dynamically-allocated
memory.
This should have no effect on any performance-critical code paths.
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org>
|
|
On the internal mic of the Packard Bell DOTS, one channel
has an inverted signal. Add a quirk to fix this up.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1523232
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In BXT-P A0, HD-Audio DMA requests is later than expected,
and makes an audio stream sensitive to system latencies when
24/32 bits are playing.
Adjusting threshold of DMA fifo to force the DMA request
sooner to improve latency tolerance at the expense of power.
v2: move Intel specific code to hda_intel.c
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
The ioctl IOC_LIBCFS_PING_TEST has not been used in ages. The recent
nidstring changes which moved all the nidstring operations from libcfs
to the LNet layer but this ioctl code was still using an nidstring
operation that was causing a circular dependency loop between libcfs and
LNet.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes (-stable fodder) + dead code removal after the
overlayfs fix.
I agree that it's better to separate from the fix part to make
backporting easier, but IMO it's not worth delaying said dead code
removal until the next window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Don't reset ->total_link_count on nested calls of vfs_path_lookup()
ovl: get rid of the dead code left from broken (and disabled) optimizations
ovl: fix permission checking for setattr
|
|
we already zero it on outermost set_nameidata(), so initialization in
path_init() is pointless and wrong. The same DoS exists on pre-4.2
kernels, but there a slightly different fix will be needed.
Cc: stable@vger.kernel.org # v4.2
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
[Al Viro] The bug is in being too enthusiastic about optimizing ->setattr()
away - instead of "copy verbatim with metadata" + "chmod/chown/utimes"
(with the former being always safe and the latter failing in case of
insufficient permissions) it tries to combine these two. Note that copyup
itself will have to do ->setattr() anyway; _that_ is where the elevated
capabilities are right. Having these two ->setattr() (one to set verbatim
copy of metadata, another to do what overlayfs ->setattr() had been asked
to do in the first place) combined is where it breaks.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"This updates contains the following changes:
- Fix a signal handling regression in the bit wait functions.
- Avoid false positive warnings in the wakeup path.
- Initialize the scheduler root domain properly.
- Handle gtime calculations in proc/$PID/stat proper.
- Add more documentation for the barriers in try_to_wake_up().
- Fix a subtle race in try_to_wake_up() which might cause a task to
be scheduled on two cpus
- Compile static helper function only when it is used"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Fix an SMP ordering race in try_to_wake_up() vs. schedule()
sched/core: Better document the try_to_wake_up() barriers
sched/cputime: Fix invalid gtime in proc
sched/core: Clear the root_domain cpumasks in init_rootdomain()
sched/core: Remove false-positive warning from wake_up_process()
sched/wait: Fix signal handling in bit wait helpers
sched/rt: Hide the push_irq_work_func() declaration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thoma Gleixner:
"Another round of fixes for x86:
- Move the initialization of the microcode driver to late_initcall to
make sure everything that init function needs is available.
- Make sure that lockdep knows about interrupts being off in the
entry code before calling into c-code.
- Undo the cpu hotplug init delay regression.
- Use the proper conditionals in the mpx instruction decoder.
- Fixup restart_syscall for x32 tasks.
- Fix the hugepage regression on PAE kernels which was introduced
with the latest PAT changes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/signal: Fix restart_syscall number for x32 tasks
x86/mpx: Fix instruction decoder condition
x86/mm: Fix regression with huge pages on PAE
x86 smpboot: Re-enable init_udelay=0 by default on modern CPUs
x86/entry/64: Fix irqflag tracing wrt context tracking
x86/microcode: Initialize the driver late when facilities are up
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is quite a bumper crop of fixes: three from Arnd correcting
various build issues in some configurations, a lock recursion in
qla2xxx. Two potentially exploitable issues in hpsa and mvsas, a
potential null deref in st, a revert of a bdi registration fix that
turned out to cause even more problems, a set of fixes to allow people
who only defined MPT2SAS to still work after the mpt2/mpt3sas merger
and a couple of fixes for issues turned up by the hyper-v storvsc
driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibility
Revert "scsi: Fix a bdi reregistration race"
mpt3sas: Add dummy Kconfig option for backwards compatibility
Fix a memory leak in scsi_host_dev_release()
block/sd: Fix device-imposed transfer length limits
scsi_debug: fix prevent_allow+verify regressions
MAINTAINERS: Add myself as co-maintainer of the SCSI subsystem.
sd: Make discard granularity match logical block size when LBPRZ=1
scsi: hpsa: select CONFIG_SCSI_SAS_ATTR
scsi: advansys needs ISA dma api for ISA support
scsi_sysfs: protect against double execution of __scsi_remove_device()
st: fix potential null pointer dereference.
scsi: report 'INQUIRY result too short' once per host
advansys: fix big-endian builds
qla2xxx: Fix rwlock recursion
hpsa: logical vs bitwise AND typo
mvsas: don't allow negative timeouts
mpt3sas: Fix use sas_is_tlr_enabled API before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag
|
|
In case we monitor events system wide, we get EXIT event
(when configured) twice for each task that exited.
Note doubled lines with same pid/tid in following example:
$ sudo ./perf record -a
^C[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.480 MB perf.data (2518 samples) ]
$ sudo ./perf report -D | grep EXIT
0 60290687567581 0x59910 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
0 60290687568354 0x59948 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
0 60290687988744 0x59ad8 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
0 60290687989198 0x59b10 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
1 60290692567895 0x62af0 [0x38]: PERF_RECORD_EXIT(1253:1253):(1253:1253)
1 60290692568322 0x62b28 [0x38]: PERF_RECORD_EXIT(1253:1253):(1253:1253)
2 60290692739276 0x69a18 [0x38]: PERF_RECORD_EXIT(1252:1252):(1252:1252)
2 60290692739910 0x69a50 [0x38]: PERF_RECORD_EXIT(1252:1252):(1252:1252)
The reason is that the cpu contexts are processes each time
we call perf_event_task. I'm changing the perf_event_aux logic
to serve task_ctx and cpu contexts separately, which ensure we
don't get EXIT event generated twice on same cpu context.
This does not affect other auxiliary events, as they don't
use task_ctx at all.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1446649205-5822-1-git-send-email-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We need to add rest of the flags to the constraint mask
instead of another INTEL_ARCH_EVENT_MASK, fixing a typo.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1447061071-28085-1-git-send-email-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There was a mistake in the Haswell constraints table.
Signed-off-by: Yuanfang Chen <cheny@udel.edu>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1448384701-9110-1-git-send-email-cheny@udel.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull drm fixes from Dave Airlie:
"A bunch of change across the board, the main things are some vblank
fallout in radeon and nouveau required some work, but I think this
should fix it all. There is also one drm fix for an oops in vmwgfx
with how we pass the drm master around.
The rest is just some amdgpu, i915, imx and rockchip fixes.
Probably more than I'd like at this point, but hopefully things settle
down now"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (40 commits)
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/nouveau: Fix pre-nv50 pageflip events (v4)
drm: Fix an unwanted master inheritance v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Introduce a gmbus power domain
drm/i915: Clean up AUX power domain handling
drm/rockchip: Use CRTC vblank event interface
drm/rockchip: Fix module autoload for OF platform driver
drm/rockchip: vop: fix window origin calculation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a couple of crypto drivers that were using memcmp to verify
authentication tags. They now use crypto_memneq instead"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: talitos - Fix timing leak in ESP ICV verification
crypto: nx - Fix timing leak in GCM and CCM decryption
|
|
When restarting a syscall with regs->ax == -ERESTART_RESTARTBLOCK,
regs->ax is assigned to a restart_syscall number. For x32 tasks, this
syscall number must have __X32_SYSCALL_BIT set, otherwise it will be
an x86_64 syscall number instead of a valid x32 syscall number. This
issue has been there since the introduction of x32.
Reported-by: strace/tests/restart_syscall.test
Reported-and-tested-by: Elvira Khabirova <lineprinter0@gmail.com>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Elvira Khabirova <lineprinter0@gmail.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20151130215436.GA25996@altlinux.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
MPX decodes instructions in order to tell which bounds register
was violated. Part of this decoding involves looking at the "REX
prefix" which is a special instrucion prefix used to retrofit
support for new registers in to old instructions.
The X86_REX_*() macros are defined to return actual bit values:
#define X86_REX_R(rex) ((rex) & 4)
*not* boolean values. However, the MPX code was checking for
them like they were booleans. This might have led to us
mis-decoding the "REX prefix" and giving false information out to
userspace about bounds violations. X86_REX_B() actually is bit 1,
so this is really only broken for the X86_REX_X() case.
Fix the conditionals up to tolerate the non-boolean values.
Fixes: fcc7ffd67991 "x86, mpx: Decode MPX instruction to get bound violation information"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: x86@kernel.org
Cc: Dave Hansen <dave@sr71.net>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20151201003113.D800C1E0@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
into drm-next
A few more last minute fixes for 4.4 on top of my pull request from
earlier this week. The big change here is a vblank regression fix due to
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many vblanks
were missed". Beyond that, a hotplug fix and a few VM fixes.
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
add blacklist for thinkpad T40p
drm/amdgpu: fix VM page table reference counting
drm/amdgpu: fix userptr flags check
|
|
PCI interrupt lines start at 1, not at 0. So, creates additional one
interrupt when register for irq domain.
Error when PCIe devices have 4 INTx:
WARNING: CPU: 1 PID: 1 at kernel/irq/irqdomain.c:280
irq_domain_associate+0x17c/0x1cc()
error: hwirq 0x4 is too large for dummy
Tested on Ethernet adapter card with multi-functions.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Check TLP packet successful completion status. This fix the issue when
accessing multi-function devices in enumeration process, TLP will return
error when accessing non-exist function number. Returns PCI error code
instead of generic errno.
Tested on Ethernet adapter card with multi-functions.
[bhelgaas: simplify completion status checking code]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The Requester ID should use the Root Port devfn and it should be always 0.
Previously we constructed the Requester ID using the *Completer* devfn,
i.e., the devfn of the Function we expect to respond to the config access.
This causes issues when accessing configuration space for devices other
than the Root Port.
Build the Requester ID using the Root Port devfn.
Tested on Ethernet adapter card with multi-functions.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
TLP_LOOP is 500 and the "loop" variable was a u8 so "loop < TLP_LOOP" is
always true. We only need this condition to work if there is a problem so
it would have been easy to miss this in testing.
Make it a normal for loop with "int i" instead of over thinking things and
making it complicated.
Fixes: 6bb4dd154ae8 ("PCI: altera: Add Altera PCIe host controller driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fix from Sage Weil:
"This addresses a refcounting bug that leads to a use-after-free"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: don't put snap_context twice in rbd_queue_workfn()
|
|
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
https://bugs.freedesktop.org/show_bug.cgi?id=93147
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Maybe replace the udelay() in the flip_work_func() by a suitable
usleep_range() for a bit better efficiency? Will try that.
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Probably fixes: fdo#93147
Port of Mario's radeon fix to amdgpu.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(v1) Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
(v2) Refine amdgpu_flip_work_func() for better efficiency.
In amdgpu_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Also small fix to code comment and formatting in that function.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
(v3) Fix crash in crtc disabled case
|
|
rme96 driver needs to reset DAC depending on the sample rate, and this
results in resetting to the max volume suddenly. It's because of the
missing call of snd_rme96_apply_dac_volume().
However, calling this function right after the DAC reset still may not
work, and we need some delay before this call. Since the DAC reset
and the procedure after that are performed in the spinlock, we delay
the DAC volume restore at the end after the spinlock.
Reported-and-tested-by: Sylvain LABOISNE <maeda1@free.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- NFIT parsing regression fixes from Linda. The nvdimm hot-add
implementation merged in 4.4-rc1 interpreted the specification in a
way that breaks actual HPE platforms. We are also closing the loop
with the ACPI Working Group to get this clarification added to the
spec.
- Andy pointed out that his laptop without nvdimm resources is loading
the e820-nvdimm module by default, fix that up to only load the
module when an e820-type-12 range is present.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: Adjust for different _FIT and NFIT headers
nfit: Fix the check for a successful NFIT merge
nfit: Account for table size length variation
libnvdimm, e820: skip module loading when no type-12
|
|
Pull ARM KVM fixes from Paolo Bonzini:
- a series of fixes to deal with the aliasing between the sp and xzr
register
- a fix for the cache flush fix that went in -rc3
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
ARM/arm64: KVM: correct PTE uncachedness check
arm64: KVM: Get rid of old vcpu_reg()
arm64: KVM: Correctly handle zero register in system register accesses
arm64: KVM: Remove const from struct sys_reg_params
arm64: KVM: Correctly handle zero register during MMIO
|
|
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
https://bugs.freedesktop.org/show_bug.cgi?id=93147
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Fixes: fdo#93147
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
(v1) Tested-by: Dave Witbrodt <dawitbro@sbcglobal.net>
(v2) Refine radeon_flip_work_func() for better efficiency:
In radeon_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Retested on DCE-3 and DCE-4 to verify it still works nicely.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
HPD signals on DVI ports can be fired off before the pins required for
DDC probing actually make contact, due to the pins for HPD making
contact first. This results in a HPD signal being asserted but DDC
probing failing, resulting in hotplugging occasionally failing.
This is somewhat rare on most cards (depending on what angle you plug
the DVI connector in), but on some cards it happens constantly. The
Radeon R5 on the machine used for testing this patch for instance, runs
into this issue just about every time I try to hotplug a DVI monitor and
as a result hotplugging almost never works.
Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
there is a protection fault about freed list when OCL test.
add a spin lock to protect it.
v2: drop changes in vm_fini
Signed-off-by: JimQu <jim.qu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
The gtt_end is already inclusive, we don't need to subtract one here.
v2 (chk): keep the fix for the VM code, cause here it really applies.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Anatoli Antonovitch <anatoli.antonovitch@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
No need for a GEM reference here.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Since 52ebea749aae ("writeback: make backing_dev_info host
cgroup-specific bdi_writebacks") inode, at some point in its lifetime,
gets attached to a wb (struct bdi_writeback). Detaching happens on
evict, in inode_detach_wb() called from __destroy_inode(), and involves
updating wb.
However, detaching an internal bdev inode from its wb in
__destroy_inode() is too late. Its bdi and by extension root wb are
embedded into struct request_queue, which has different lifetime rules
and can be freed long before the final bdput() is called (can be from
__fput() of a corresponding /dev inode, through dput() - evict() -
bd_forget(). bdevs hold onto the underlying disk/queue pair only while
opened; as soon as bdev is closed all bets are off. In fact,
disk/queue can be gone before __blkdev_put() even returns:
1499 static void __blkdev_put(struct block_device *bdev, fmode_t mode, int for_part)
1500 {
...
1518 if (bdev->bd_contains == bdev) {
1519 if (disk->fops->release)
1520 disk->fops->release(disk, mode);
[ Driver puts its references to disk/queue ]
1521 }
1522 if (!bdev->bd_openers) {
1523 struct module *owner = disk->fops->owner;
1524
1525 disk_put_part(bdev->bd_part);
1526 bdev->bd_part = NULL;
1527 bdev->bd_disk = NULL;
1528 if (bdev != bdev->bd_contains)
1529 victim = bdev->bd_contains;
1530 bdev->bd_contains = NULL;
1531
1532 put_disk(disk);
[ We put ours, the queue is gone
The last bdput() would result in a write to invalid memory ]
1533 module_put(owner);
...
1539 }
Since bdev inodes are special anyway, detach them in __blkdev_put()
after clearing inode's dirty bits, turning the problematic
inode_detach_wb() in __destroy_inode() into a noop.
add_disk() grabs its disk->queue since 523e1d399ce0 ("block: make
gendisk hold a reference to its queue"), so the old ->release comment
is removed in favor of the new inode_detach_wb() comment.
Cc: stable@vger.kernel.org # 4.2+, needs backporting
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Tested-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Move the selection of the pinctrl driver to SoC family level since we
have two pinctrl drivers. It is useless to select one which is not
compatible with the SoC.
[abelloni: fixed pm.c when only sama2d2 is selected]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
No need for the GEM reference here.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM fixes for v4.4-rc4
- A series of fixes to deal with the aliasing between the sp and xzr register
- A fix for the cache flush fix that went in -rc3
|
|
Not necessary for VRAM.
v2: no need to check if ttm is NULL.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
introduced jbd2_write_access_granted() to improve write|undo_access
speed, but missed to check the status of b_committed_data which caused
a kernel panic on ocfs2.
[ 6538.405938] ------------[ cut here ]------------
[ 6538.406686] kernel BUG at fs/ocfs2/suballoc.c:2400!
[ 6538.406686] invalid opcode: 0000 [#1] SMP
[ 6538.406686] Modules linked in: ocfs2 nfsd lockd grace nfs_acl auth_rpcgss sunrpc autofs4 ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm ocfs2_nodemanager ocfs2_stackglue configfs sd_mod sg ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables be2iscsi iscsi_boot_sysfs bnx2i cnic uio cxgb4i cxgb4 cxgb3i libcxgbi cxgb3 mdio ib_iser rdma_cm ib_cm iw_cm ib_sa ib_mad ib_core ib_addr ipv6 iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ppdev xen_kbdfront xen_netfront xen_fbfront parport_pc parport pcspkr i2c_piix4 acpi_cpufreq ext4 jbd2 mbcache xen_blkfront floppy pata_acpi ata_generic ata_piix cirrus ttm drm_kms_helper drm fb_sys_fops sysimgblt sysfillrect i2c_core syscopyarea dm_mirror dm_region_hash dm_log dm_mod
[ 6538.406686] CPU: 1 PID: 16265 Comm: mmap_truncate Not tainted 4.3.0 #1
[ 6538.406686] Hardware name: Xen HVM domU, BIOS 4.3.1OVM 05/14/2014
[ 6538.406686] task: ffff88007c2bab00 ti: ffff880075b78000 task.ti: ffff880075b78000
[ 6538.406686] RIP: 0010:[<ffffffffa06a286b>] [<ffffffffa06a286b>] ocfs2_block_group_clear_bits+0x23b/0x250 [ocfs2]
[ 6538.406686] RSP: 0018:ffff880075b7b7f8 EFLAGS: 00010246
[ 6538.406686] RAX: ffff8800760c5b40 RBX: ffff88006c06a000 RCX: ffffffffa06e6df0
[ 6538.406686] RDX: 0000000000000000 RSI: ffff88007a6f6ea0 RDI: ffff88007a760430
[ 6538.406686] RBP: ffff880075b7b878 R08: 0000000000000002 R09: 0000000000000001
[ 6538.406686] R10: ffffffffa06769be R11: 0000000000000000 R12: 0000000000000001
[ 6538.406686] R13: ffffffffa06a1750 R14: 0000000000000001 R15: ffff88007a6f6ea0
[ 6538.406686] FS: 00007f17fde30720(0000) GS:ffff88007f040000(0000) knlGS:0000000000000000
[ 6538.406686] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 6538.406686] CR2: 0000000000601730 CR3: 000000007aea0000 CR4: 00000000000406e0
[ 6538.406686] Stack:
[ 6538.406686] ffff88007c2bb5b0 ffff880075b7b8e0 ffff88007a7604b0 ffff88006c640800
[ 6538.406686] ffff88007a7604b0 ffff880075d77390 0000000075b7b878 ffffffffa06a309d
[ 6538.406686] ffff880075d752d8 ffff880075b7b990 ffff880075b7b898 0000000000000000
[ 6538.406686] Call Trace:
[ 6538.406686] [<ffffffffa06a309d>] ? ocfs2_read_group_descriptor+0x6d/0xa0 [ocfs2]
[ 6538.406686] [<ffffffffa06a3654>] _ocfs2_free_suballoc_bits+0xe4/0x320 [ocfs2]
[ 6538.406686] [<ffffffffa06a1750>] ? ocfs2_put_slot+0xf0/0xf0 [ocfs2]
[ 6538.406686] [<ffffffffa06a397e>] _ocfs2_free_clusters+0xee/0x210 [ocfs2]
[ 6538.406686] [<ffffffffa06a1750>] ? ocfs2_put_slot+0xf0/0xf0 [ocfs2]
[ 6538.406686] [<ffffffffa06a1750>] ? ocfs2_put_slot+0xf0/0xf0 [ocfs2]
[ 6538.406686] [<ffffffffa0682d50>] ? ocfs2_extend_trans+0x50/0x1a0 [ocfs2]
[ 6538.406686] [<ffffffffa06a3ad5>] ocfs2_free_clusters+0x15/0x20 [ocfs2]
[ 6538.406686] [<ffffffffa065072c>] ocfs2_replay_truncate_records+0xfc/0x290 [ocfs2]
[ 6538.406686] [<ffffffffa06843ac>] ? ocfs2_start_trans+0xec/0x1d0 [ocfs2]
[ 6538.406686] [<ffffffffa0654600>] __ocfs2_flush_truncate_log+0x140/0x2d0 [ocfs2]
[ 6538.406686] [<ffffffffa0654394>] ? ocfs2_reserve_blocks_for_rec_trunc.clone.0+0x44/0x170 [ocfs2]
[ 6538.406686] [<ffffffffa065acd4>] ocfs2_remove_btree_range+0x374/0x630 [ocfs2]
[ 6538.406686] [<ffffffffa017486b>] ? jbd2_journal_stop+0x25b/0x470 [jbd2]
[ 6538.406686] [<ffffffffa065d5b5>] ocfs2_commit_truncate+0x305/0x670 [ocfs2]
[ 6538.406686] [<ffffffffa0683430>] ? ocfs2_journal_access_eb+0x20/0x20 [ocfs2]
[ 6538.406686] [<ffffffffa067adb7>] ocfs2_truncate_file+0x297/0x380 [ocfs2]
[ 6538.406686] [<ffffffffa01759e4>] ? jbd2_journal_begin_ordered_truncate+0x64/0xc0 [jbd2]
[ 6538.406686] [<ffffffffa067c7a2>] ocfs2_setattr+0x572/0x860 [ocfs2]
[ 6538.406686] [<ffffffff810e4a3f>] ? current_fs_time+0x3f/0x50
[ 6538.406686] [<ffffffff812124b7>] notify_change+0x1d7/0x340
[ 6538.406686] [<ffffffff8121abf9>] ? generic_getxattr+0x79/0x80
[ 6538.406686] [<ffffffff811f5876>] do_truncate+0x66/0x90
[ 6538.406686] [<ffffffff81120e30>] ? __audit_syscall_entry+0xb0/0x110
[ 6538.406686] [<ffffffff811f5bb3>] do_sys_ftruncate.clone.0+0xf3/0x120
[ 6538.406686] [<ffffffff811f5bee>] SyS_ftruncate+0xe/0x10
[ 6538.406686] [<ffffffff816aa2ae>] entry_SYSCALL_64_fastpath+0x12/0x71
[ 6538.406686] Code: 28 48 81 ee b0 04 00 00 48 8b 92 50 fb ff ff 48 8b 80 b0 03 00 00 48 39 90 88 00 00 00 0f 84 30 fe ff ff 0f 0b eb fe 0f 0b eb fe <0f> 0b 0f 1f 00 eb fb 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00
[ 6538.406686] RIP [<ffffffffa06a286b>] ocfs2_block_group_clear_bits+0x23b/0x250 [ocfs2]
[ 6538.406686] RSP <ffff880075b7b7f8>
[ 6538.691128] ---[ end trace 31cd7011d6770d7e ]---
[ 6538.694492] Kernel panic - not syncing: Fatal exception
[ 6538.695484] Kernel Offset: disabled
Fixes: de92c8caf16c("jbd2: speedup jbd2_journal_get_[write|undo]_access()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This time we've got a larger number of updates, mainly from ASoC
world. The only significant LOCs found here are for Realtek codecs,
where most of changes are quite systematic replacements.
There are also a few fixes in ASoC core side: one is the PM call order
fix to ensure the DPAM resume working properly. Another is the proper
cleanup call after freeing DAPM widgets, and the correction of the
wrong callback set in topology API.
The rest are a wide range of driver-specific small fixes, including
HD-audio"
* tag 'sound-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (35 commits)
ALSA: hda - Add Conexant CX8200 (14f1:2008) codec entry
ALSA: hda - Correct codec names for 14f1:50f1 and 14f1:50f3
ALSA: hda - Skip ELD notification during system suspend
ASoC: core: Change power state before rechecking endpoint
ASoC: fix kernel-doc warnings in sound/soc/soc-ops.c
ASoC: rt5645: Add dmi_system_id "Google Terra"
ASoC: rockchip: Fix incorrect VDW value for 24 bit
ASoC: fsl: clarify ac97 dependency
ASoC: Intel: Skylake: fix memory leak
ASoC: davinci-mcasp: Fix master capture only mode
ASoC: es8328: Fix shifts for mixer switches
ASoC: rt5645: Add dmi_system_id "Google Wizpig"
ASoC: sti: set player private data
ASoC: sti: rename ST proprietary DT properties
ASoC: sti: remove wrong error message
ASoC: Intel: Skylake: Add I2C depends for SKL machine
ASoC: topology: fix info callback for TLV byte control
ASoC: rt5670: fix wrong bit def for pll src
ASoC: nau8825: add pm function
ASoC: rt5645: Add struct dmi_system_id "Google Edgar" for Chrome OS
...
|
|
As the SDHCI controller needs the 1.8V line to be always enabled for some eMMC
configurations, set the proper "regulator-always-on" property to the board DTS
files.
Note that the sdhci classical regulator definitions doesn't suit our controller
for this 1.8V purpose.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix a recent regression in the ACPI PCI host bridge
initialization code, clean up some recent changes (generic power
domains framework, ACPI AML debugger support), fix three older but
annoying bugs (PCI power management. generic power domains framework,
cpufreq) and a build problem (device properties framework), and update
a stale MAINTAINERS entry (ACPI backlight driver).
Specifics:
- Fix a regression in the ACPI PCI host bridge initialization code
introduced by the recent consolidation of the host bridge handling
on x86 and ia64 that forgot to take one special piece of code
related to NUMA on x86 into account (Liu Jiang).
- Improve the Kconfig help description of the new ACPI AML debugger
support option to avoid possible confusion (Peter Zijlstra).
- Remove a piece of code in the generic power domains framework that
should have been removed by one of the recent commits modifying
that code (Ulf Hansson).
- Reduce the log level of a PCI PM message that generates a lot of
false-positive log noise for some drivers and improve the message
itself while at it (Imre Deak).
- Fix the OF-based domain lookup code in the generic power domains
framework to make it drop references to DT nodes correctly (Eric
Anholt).
- Prevent the cpufreq core from setting the policy back to the
default after a CPU offline/online cycle for cpufreq drivers
providing the ->setpolicy callback (Srinivas Pandruvada).
- Fix a build problem for CONFIG_ACPI unset in the device properties
framework (Hanjun Guo).
- Fix a stale file path in the ACPI backlight driver entry in
MAINTAINERS (Dan Carpenter)"
* tag 'pm+acpi-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
cpufreq: use last policy after online for drivers with ->setpolicy
PCI / PM: Tune down retryable runtime suspend error messages
PM / Domains: Validate cases of a non-bound driver in genpd governor
MAINTAINERS: ACPI / video: update a file name in drivers/acpi/
ACPI / property: fix compile error for acpi_node_get_property_reference() when CONFIG_ACPI=n
x86/PCI/ACPI: Fix regression caused by commit 4d6b4e69a245
ACPI: Better describe ACPI_DEBUGGER
|
|
Commit e6fab5442345 ("ARM/arm64: KVM: test properly for a PTE's
uncachedness") modified the logic to test whether a HYP or stage-2
mapping needs flushing, from [incorrectly] interpreting the page table
attributes to [incorrectly] checking whether the PFN that backs the
mapping is covered by host system RAM. The PFN number is part of the
output of the translation, not the input, so we have to use pte_pfn()
on the contents of the PTE, not __phys_to_pfn() on the HYP virtual
address or stage-2 intermediate physical address.
Fixes: e6fab5442345 ("ARM/arm64: KVM: test properly for a PTE's uncachedness")
Cc: stable@vger.kernel.org
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Using oldstyle vcpu_reg() accessor is proven to be inappropriate and
unsafe on ARM64. This patch converts the rest of use cases to new
accessors and completely removes vcpu_reg() on ARM64.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
System register accesses also use zero register for Rt == 31, and
therefore using it will also result in getting SP value instead. This
patch makes them also using new accessors, introduced by the previous
patch. Since register value is no longer directly associated with storage
inside vCPU context structure, we introduce a dedicated storage for it in
struct sys_reg_params.
This refactor also gets rid of "massive hack" in kvm_handle_cp_64().
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
