| Age | Commit message (Collapse) | Author |
|---|
|
Saving the port count bump is unsafe. If the tty is hung up while
this open was blocking, the port count is zeroed.
Explicitly check if the tty was hung up while blocking, and correct
the port count if not.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net into intel
Jeff Kirsher says:
===================
This series contains fixes to e1000e and igb.
The e1000e fix resolves an issue at 1000Mbps link speed, where one of the
MAC's internal clocks can be stopped for up to 4us when entering K1 (a
power mode of the MAC-PHY interconnect). If the MAC is waiting for
completion indications for 2 DMA write requests into Host memory
(e.g. descriptor writeback or Rx packet writing) and the
indications occur while the clock is stopped, both indications will be
missed by the MAC causing the MAC to wait for the completion indications
and be unable to generate further DMA write requests. This results in an
apparent hardware hang. The patch works-around the issue by disabling
the de-assertion of the clock request when 1000Mbps link is acquired (K1
must be disabled while doing this).
The igb fix to drop BUILD_BUG_ON check from igb_build_rx_buffer resolves
a build error on s390 devices. The igb driver was throwing a build error
due to the fact that a frame built using build_skb would be larger than 2K.
Since this is not likely to change at any point in the future we are better
off just dropping the check since we already had a check in
igb_set_rx_buffer_len that will just disable the usage of build_skb anyway.
The igb fix for i210 link setup changes the setup copper link function
to use a switch statement, so that the appropriate setup link function
is called for the given PHY types.
Lastly, the igb fix for a lockdep issue in igb_get_i2c_client resolves
the issue by re-factoring the initialization and usage of the i2c_client.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few powerpc bits & fixes for rc1. A couple of str*cpy
fixes, some fixes in handling the FSCR register on Power8 (controls
the enabling of processor features), a 32-bit build fix and a couple
more nits."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Set DSCR bit in FSCR setup
powerpc: Add DSCR FSCR register bit definition
powerpc: Fix setting FSCR for HV=0 and on secondary CPUs
powerpc: Wireup the kcmp syscall to sys_ni
powerpc: Remove unused BITOP_LE_SWIZZLE macro
powerpc: Avoid link stack corruption in MMU on syscall entry path
drivers/tty/hvc: Use strlcpy instead of strncpy
powerpc/pseries/hvcserver: Fix strncpy buffer limit in location code
powerpc: Fix compile of sha1-powerpc-asm.S on 32-bit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio hwrng fix from Rusty Russell:
"Nasty side-effect of vmalloc'ing modules: their static vars cannot be
put into scatterlists. Jens has a check queued for this, so it
shouldn't happen again.
We could fix this in virtio_rng, but it's actually far easier to just
do it in the core"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
hw_random: make buffer usable in scatterlist.
|
|
Pull networking fixes from David Miller:
"A moderately sized pile of fixes, some specifically for merge window
introduced regressions although others are for longer standing items
and have been queued up for -stable.
I'm kind of tired of all the RDS protocol bugs over the years, to be
honest, it's way out of proportion to the number of people who
actually use it.
1) Fix missing range initialization in netfilter IPSET, from Jozsef
Kadlecsik.
2) ieee80211_local->tim_lock needs to use BH disabling, from Johannes
Berg.
3) Fix DMA syncing in SFC driver, from Ben Hutchings.
4) Fix regression in BOND device MAC address setting, from Jiri
Pirko.
5) Missing usb_free_urb in ISDN Hisax driver, from Marina Makienko.
6) Fix UDP checksumming in bnx2x driver for 57710 and 57711 chips,
fix from Dmitry Kravkov.
7) Missing cfgspace_lock initialization in BCMA driver.
8) Validate parameter size for SCTP assoc stats getsockopt(), from
Guenter Roeck.
9) Fix SCTP association hangs, from Lee A Roberts.
10) Fix jumbo frame handling in r8169, from Francois Romieu.
11) Fix phy_device memory leak, from Petr Malat.
12) Omit trailing FCS from frames received in BGMAC driver, from Hauke
Mehrtens.
13) Missing socket refcount release in L2TP, from Guillaume Nault.
14) sctp_endpoint_init should respect passed in gfp_t, rather than use
GFP_KERNEL unconditionally. From Dan Carpenter.
15) Add AISX AX88179 USB driver, from Freddy Xin.
16) Remove MAINTAINERS entries for drivers deleted during the merge
window, from Cesar Eduardo Barros.
17) RDS protocol can try to allocate huge amounts of memory, check
that the user's request length makes sense, from Cong Wang.
18) SCTP should use the provided KMALLOC_MAX_SIZE instead of it's own,
bogus, definition. From Cong Wang.
19) Fix deadlocks in FEC driver by moving TX reclaim into NAPI poll,
from Frank Li. Also, fix a build error introduced in the merge
window.
20) Fix bogus purging of default routes in ipv6, from Lorenzo Colitti.
21) Don't double count RTT measurements when we leave the TCP receive
fast path, from Neal Cardwell."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tcp: fix double-counted receiver RTT when leaving receiver fast path
CAIF: fix sparse warning for caif_usb
rds: simplify a warning message
net: fec: fix build error in no MXC platform
net: ipv6: Don't purge default router if accept_ra=2
net: fec: put tx to napi poll function to fix dead lock
sctp: use KMALLOC_MAX_SIZE instead of its own MAX_KMALLOC_SIZE
rds: limit the size allocated by rds_message_alloc()
MAINTAINERS: remove eexpress
MAINTAINERS: remove drivers/net/wan/cycx*
MAINTAINERS: remove 3c505
caif_dev: fix sparse warnings for caif_flow_cb
ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver
sctp: use the passed in gfp flags instead GFP_KERNEL
ipv[4|6]: correct dropwatch false positive in local_deliver_finish
l2tp: Restore socket refcount when sendmsg succeeds
net/phy: micrel: Disable asymmetric pause for KSZ9021
bgmac: omit the fcs
phy: Fix phy_device_free memory leak
bnx2x: Fix KR2 work-around condition
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes and cleanups from Thomas Gleixner:
"Commit e5ab012c3271 ("nohz: Make tick_nohz_irq_exit() irq safe") is
the first commit in the series and the minimal necessary bugfix, which
needs to go back into stable.
The remanining commits enforce irq disabling in irq_exit(), sanitize
the hardirq/softirq preempt count transition and remove a bunch of no
longer necessary conditionals."
I personally love getting rid of the very subtle and confusing
IRQ_EXIT_OFFSET thing. Even apart from the whole "more lines removed
than added" thing.
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq: Don't re-enable interrupts at the end of irq_exit
irq: Remove IRQ_EXIT_OFFSET workaround
Revert "nohz: Make tick_nohz_irq_exit() irq safe"
irq: Sanitize invoke_softirq
irq: Ensure irq_exit() code runs with interrupts disabled
nohz: Make tick_nohz_irq_exit() irq safe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smpboot bugfix from Thomas Gleixner:
"A single bugfix for a regression introduced with the conversion of the
stop machine threads to the generic smpboot thread management
facility"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stop_machine: Mark per cpu stopper enabled early
|
|
Pull second round of GPIO changes from Grant Likely:
"This branch contains a few bug fixes that I missed the first time
around and updates to the gpio_desc series included in the first pull
request. This tag has been retagged to drop the 2 head commits
because the one of them caused a build failure."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio/gpio-ich: fix ichx_gpio_check_available() return what callers expect
gpiolib: move comment to right function
gpiolib: use const parameters when possible
gpiolib: check descriptors validity before use
|
|
Pull md updates from NeilBrown:
"Mostly little bugfixes.
Only "feature" is a new RAID10 layout which slightly improves the
number of sets of devices that can concurrently fail, without data
loss."
* tag 'md-3.9' of git://neil.brown.name/md:
md: expedite metadata update when switching read-auto -> active
md: remove CONFIG_MULTICORE_RAID456
md/raid1,raid10: fix deadlock with freeze_array()
md/raid0: improve error message when converting RAID4-with-spares to RAID0
md: raid0: fix error return from create_stripe_zones.
md: fix two bugs when attempting to resize RAID0 array.
DM RAID: Add support for MD's RAID10 "far" and "offset" algorithms
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 2)
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 1)
MD RAID10: Minor non-functional code changes
md: raid1,10: Handle REQ_WRITE_SAME flag in write bios
md: protect against crash upon fsync on ro array
|
|
This patch fixes a lockdep warning in igb_get_i2c_client by
refactoring the initialization and usage of the i2c_client
completely. There is no on the fly allocation of the single
client needed today.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes the setup copper link function to use a switch
statement for the PHY id's available for the given PHY types. It
also adds a case for the I210 PHY id, so the appropriate setup link
function is called for it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On s390 the igb driver was throwing a build error due to the fact that a frame
built using build_skb would be larger than 2K. Since this is not likely to
change at any point in the future we are better off just dropping the check
since we already had a check in igb_set_rx_buffer_len that will just disable
the usage of build_skb anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
At 1000Mbps link speed, one of the MAC's internal clocks can be stopped for
up to 4us when entering K1 (a power mode of the MAC-PHY interconnect). If
the MAC is waiting for completion indications for 2 DMA write requests into
Host memory (e.g. descriptor writeback or Rx packet writing) and the
indications occur while the clock is stopped, both indications will be
missed by the MAC causing the MAC to wait for the completion indications
and be unable to generate further DMA write requests. This results in an
apparent hardware hang.
Work-around the issue by disabling the de-assertion of the clock request
when 1000Mbps link is acquired (K1 must be disabled while doing this).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We support DSCR (Data Stream Control Register) so we should make sure we set it
in the FSCR (Facility Status & Control Register) incase some firmwares don't
set it. If we don't set this, we'll take a facility unavailable exception when
using the DSCR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This sets the DSCR (Data Stream Control Register) in the FSCR (Facility Status
& Control Register).
Also harmonise TAR (Target Address Register) FSCR bit definition too.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Currently we only set the FSCR (Facility Status and Control Register) when HV=1
but this feature is available when HV=0 also. This patch sets FSCR when HV=0.
Also, we currently only set the FSCR on the master CPU. This patch also sets
the FSCR on secondary CPUs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Since kmp takes 2 unsigned long args there should be a compat wrapper.
Since one isn't provided I think it's safer just to hook this up to not
implemented. If we need it later we can do it properly then.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The BITOP_LE_SWIZZLE macro was used in the little-endian bitops functions
for powerpc. But these functions were converted to generic bitops and
the BITOP_LE_SWIZZLE is not used anymore.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Currently we use the link register to branch up high in the early MMU on
syscall entry path. Unfortunately, this trashes the link stack as the
address we are going to is not associated with the earlier mflr.
This patch simply converts us to used the count register (volatile over
syscalls anyway) instead. This is much better at predicting in this
scenario and doesn't trash link stack causing a bunch of additional
branch mispredicts later. Benchmarking this on POWER8 saves a bunch of
cycles on Anton's null syscall benchmark here:
http://ozlabs.org/~anton/junkcode/null_syscall.c
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
when strlen pi->location_code is larger than HVCS_CLC_LENGTH + 1,
original implementation can not let hvcsd->p_location_code NUL terminated.
so need fix it (also can simplify the code)
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
the dest buf len is 80 (HVCS_CLC_LENGTH + 1).
the src buf len is PAGE_SIZE.
if src buf string len is more than 80, it will cause issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When building with CRYPTO_SHA1_PPC enabled we fail with:
powerpc/crypto/sha1-powerpc-asm.S: Assembler messages:
powerpc/crypto/sha1-powerpc-asm.S:116: Error: can't resolve `0' {*ABS* section} - `STACKFRAMESIZE' {*UND* section}
powerpc/crypto/sha1-powerpc-asm.S:116: Error: expression too complex
powerpc/crypto/sha1-powerpc-asm.S:178: Error: unsupported relocation against STACKFRAMESIZE
Use INT_FRAME_SIZE instead of STACKFRAMESIZE.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
virtio_rng feeds the randomness buffer handed by the core directly
into the scatterlist, since commit bb347d98079a547e80bd4722dee1de61e4dca0e8.
However, if CONFIG_HW_RANDOM=m, the static buffer isn't a linear address
(at least on most archs). We could fix this in virtio_rng, but it's actually
far easier to just do it in the core as virtio_rng would have to allocate
a buffer every time (it doesn't know how much the core will want to read).
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
|
|
We should not update ts_recent and call tcp_rcv_rtt_measure_ts() both
before and after going to step5. That wastes CPU and double-counts the
receiver-side RTT sample.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes the following sparse warning:
net/caif/caif_usb.c:84:16: warning: symbol 'cfusbl_create' was not
declared. Should it be static?
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: David S. Miller <davem@davemloft.net>
Cc: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
build error cause by
Commit ff43da86c69d76a726ffe7d1666148960dc1d108
("NET: FEC: dynamtic check DMA desc buff type")
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_nextdesc’:
drivers/net/ethernet/freescale/fec.c:215:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_prevdesc’:
drivers/net/ethernet/freescale/fec.c:224:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_start_xmit’:
drivers/net/ethernet/freescale/fec.c:286:37: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:287:13: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:324:7: error: dereferencing pointer to incomplete type etc....
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting net.ipv6.conf.<interface>.accept_ra=2 causes the kernel
to accept RAs even when forwarding is enabled. However, enabling
forwarding purges all default routes on the system, breaking
connectivity until the next RA is received. Fix this by not
purging default routes on interfaces that have accept_ra=2.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
up stack ndo_start_xmit already hold lock.
fec_enet_start_xmit needn't spin lock.
stat_xmit just update fep->cur_tx
fec_enet_tx just update fep->dirty_tx
Reserve a empty bdb to check full or empty
cur_tx == dirty_tx means full
cur_tx == dirty_tx +1 means empty
So needn't is_full variable.
Fix spin lock deadlock
=================================
[ INFO: inconsistent lock state ]
3.8.0-rc5+ #107 Not tainted
---------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
ptp4l/615 [HC1[1]:SC0[0]:HE0:SE1] takes:
(&(&list->lock)->rlock#3){?.-...}, at: [<8042c3c4>] skb_queue_tail+0x20/0x50
{HARDIRQ-ON-W} state was registered at:
[<80067250>] mark_lock+0x154/0x4e8
[<800676f4>] mark_irqflags+0x110/0x1a4
[<80069208>] __lock_acquire+0x494/0x9c0
[<80069ce8>] lock_acquire+0x90/0xa4
[<80527ad0>] _raw_spin_lock_bh+0x44/0x54
[<804877e0>] first_packet_length+0x38/0x1f0
[<804879e4>] udp_poll+0x4c/0x5c
[<804231f8>] sock_poll+0x24/0x28
[<800d27f0>] do_poll.isra.10+0x120/0x254
[<800d36e4>] do_sys_poll+0x15c/0x1e8
[<800d3828>] sys_poll+0x60/0xc8
[<8000e780>] ret_fast_syscall+0x0/0x3c
*** DEADLOCK ***
1 lock held by ptp4l/615:
#0: (&(&fep->hw_lock)->rlock){-.-...}, at: [<80355f9c>] fec_enet_tx+0x24/0x268
stack backtrace:
Backtrace:
[<800121e0>] (dump_backtrace+0x0/0x10c) from [<80516210>] (dump_stack+0x18/0x1c)
r6:8063b1fc r5:bf38b2f8 r4:bf38b000 r3:bf38b000
[<805161f8>] (dump_stack+0x0/0x1c) from [<805189d0>] (print_usage_bug.part.34+0x164/0x1a4)
[<8051886c>] (print_usage_bug.part.34+0x0/0x1a4) from [<80518a88>] (print_usage_bug+0x78/0x88)
r8:80065664 r7:bf38b2f8 r6:00000002 r5:00000000 r4:bf38b000
[<80518a10>] (print_usage_bug+0x0/0x88) from [<80518b58>] (mark_lock_irq+0xc0/0x270)
r7:bf38b000 r6:00000002 r5:bf38b2f8 r4:00000000
[<80518a98>] (mark_lock_irq+0x0/0x270) from [<80067270>] (mark_lock+0x174/0x4e8)
[<800670fc>] (mark_lock+0x0/0x4e8) from [<80067744>] (mark_irqflags+0x160/0x1a4)
[<800675e4>] (mark_irqflags+0x0/0x1a4) from [<80069208>] (__lock_acquire+0x494/0x9c0)
r5:00000002 r4:bf38b2f8
[<80068d74>] (__lock_acquire+0x0/0x9c0) from [<80069ce8>] (lock_acquire+0x90/0xa4)
[<80069c58>] (lock_acquire+0x0/0xa4) from [<805278d8>] (_raw_spin_lock_irqsave+0x4c/0x60)
[<8052788c>] (_raw_spin_lock_irqsave+0x0/0x60) from [<8042c3c4>] (skb_queue_tail+0x20/0x50)
r6:bfbb2180 r5:bf1d0190 r4:bf1d0184
[<8042c3a4>] (skb_queue_tail+0x0/0x50) from [<8042c4cc>] (sock_queue_err_skb+0xd8/0x188)
r6:00000056 r5:bfbb2180 r4:bf1d0000 r3:00000000
[<8042c3f4>] (sock_queue_err_skb+0x0/0x188) from [<8042d15c>] (skb_tstamp_tx+0x70/0xa0)
r6:bf0dddb0 r5:bf1d0000 r4:bfbb2180 r3:00000004
[<8042d0ec>] (skb_tstamp_tx+0x0/0xa0) from [<803561d0>] (fec_enet_tx+0x258/0x268)
r6:c089d260 r5:00001c00 r4:bfbd0000
[<80355f78>] (fec_enet_tx+0x0/0x268) from [<803562cc>] (fec_enet_interrupt+0xec/0xf8)
[<803561e0>] (fec_enet_interrupt+0x0/0xf8) from [<8007d5b0>] (handle_irq_event_percpu+0x54/0x1a0)
[<8007d55c>] (handle_irq_event_percpu+0x0/0x1a0) from [<8007d740>] (handle_irq_event+0x44/0x64)
[<8007d6fc>] (handle_irq_event+0x0/0x64) from [<80080690>] (handle_fasteoi_irq+0xc4/0x15c)
r6:bf0dc000 r5:bf811290 r4:bf811240 r3:00000000
[<800805cc>] (handle_fasteoi_irq+0x0/0x15c) from [<8007ceec>] (generic_handle_irq+0x28/0x38)
r5:807130c8 r4:00000096
[<8007cec4>] (generic_handle_irq+0x0/0x38) from [<8000f16c>] (handle_IRQ+0x54/0xb4)
r4:8071d280 r3:00000180
[<8000f118>] (handle_IRQ+0x0/0xb4) from [<80008544>] (gic_handle_irq+0x30/0x64)
r8:8000e924 r7:f4000100 r6:bf0ddef8 r5:8071c974 r4:f400010c
r3:00000000
[<80008514>] (gic_handle_irq+0x0/0x64) from [<8000e2e4>] (__irq_svc+0x44/0x5c)
Exception stack(0xbf0ddef8 to 0xbf0ddf40)
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't definite its own MAX_KMALLOC_SIZE, use the one
defined in mm.
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dave Jones reported the following bug:
"When fed mangled socket data, rds will trust what userspace gives it,
and tries to allocate enormous amounts of memory larger than what
kmalloc can satisfy."
WARNING: at mm/page_alloc.c:2393 __alloc_pages_nodemask+0xa0d/0xbe0()
Hardware name: GA-MA78GM-S2H
Modules linked in: vmw_vsock_vmci_transport vmw_vmci vsock fuse bnep dlci bridge 8021q garp stp mrp binfmt_misc l2tp_ppp l2tp_core rfcomm s
Pid: 24652, comm: trinity-child2 Not tainted 3.8.0+ #65
Call Trace:
[<ffffffff81044155>] warn_slowpath_common+0x75/0xa0
[<ffffffff8104419a>] warn_slowpath_null+0x1a/0x20
[<ffffffff811444ad>] __alloc_pages_nodemask+0xa0d/0xbe0
[<ffffffff8100a196>] ? native_sched_clock+0x26/0x90
[<ffffffff810b2128>] ? trace_hardirqs_off_caller+0x28/0xc0
[<ffffffff810b21cd>] ? trace_hardirqs_off+0xd/0x10
[<ffffffff811861f8>] alloc_pages_current+0xb8/0x180
[<ffffffff8113eaaa>] __get_free_pages+0x2a/0x80
[<ffffffff811934fe>] kmalloc_order_trace+0x3e/0x1a0
[<ffffffff81193955>] __kmalloc+0x2f5/0x3a0
[<ffffffff8104df0c>] ? local_bh_enable_ip+0x7c/0xf0
[<ffffffffa0401ab3>] rds_message_alloc+0x23/0xb0 [rds]
[<ffffffffa04043a1>] rds_sendmsg+0x2b1/0x990 [rds]
[<ffffffff810b21cd>] ? trace_hardirqs_off+0xd/0x10
[<ffffffff81564620>] sock_sendmsg+0xb0/0xe0
[<ffffffff810b2052>] ? get_lock_stats+0x22/0x70
[<ffffffff810b24be>] ? put_lock_stats.isra.23+0xe/0x40
[<ffffffff81567f30>] sys_sendto+0x130/0x180
[<ffffffff810b872d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff816c547b>] ? _raw_spin_unlock_irq+0x3b/0x60
[<ffffffff816cd767>] ? sysret_check+0x1b/0x56
[<ffffffff810b8695>] ? trace_hardirqs_on_caller+0x115/0x1a0
[<ffffffff81341d8e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff816cd742>] system_call_fastpath+0x16/0x1b
---[ end trace eed6ae990d018c8b ]---
Reported-by: Dave Jones <davej@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit c14b78e7decd0d1d5add6a4604feb8609fe920a9 ("netfilter:
nfnetlink: add mutex per subsystem") building nefnetlink.o without
CONFIG_PROVE_RCU set, triggers this GCC warning:
net/netfilter/nfnetlink.c:65:22: warning: ‘nfnl_get_lock’ defined but not used [-Wunused-function]
The cause of that warning is, in short, that rcu_lockdep_assert()
compiles away if CONFIG_PROVE_RCU is not set. Silence this warning by
open coding nfnl_get_lock() in the sole place it was called, which
allows to remove that function.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We should stop generting audit log if audit is disabled.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This flow happens when we get a failed single Tx response
on an AMPDU queue. In this case, the frame won't be sent
any more. So we need to move the window on the recipient
side. This is done by a BAR.
Now if we are in the following case: 10, 12 and 13 are ACKed
and 11 isn't.
10 11 12 13.
V X V V
Then, 11 will be sent 16 times as an MPDU (as oppsed to
A-MPDU). If this failed, we are entering the flow described
above. So we need to send a BAR with ssn = 12.
But in this case, the scheduler will tell us to free frames
up to 13 (included).
So, it is perfectly possible to get a failed single Tx
response on an AMPDU queue that makes the scheduler's ssn
jump by more than 1 single packet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make the rssi more accurate by taking in count per-chain AGC
values. Without this, the RSSI reports inaccurate values.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since the device is being restarted, all the Rx / Tx Block
Ack sessions are been wiped out by the driver. So ignore
the requests from mac80211 that stops Tx agg while
reconfiguring the device.
Note that stopping a non-existing Rx BA session is harmless,
so just honor mac80211's request.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This fix removes the override of calibration request values sent
to the FW.
Due to that, the sending of default values to now implemented
calibrations is removed.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The phy_cfg is given from the TLV value and does not have to be
built by us.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We must set the valid TX antennas number in the ucode before
sending the phy_cfg_cmd and request for calibrations.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This situation is clearly an error situation and the only
way to recover is to restart the driver / fw.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
git://git.infradead.org/users/dhowells/linux-headers
Pull fbdev UAPI disintegration from David Howells:
"You'll be glad to here that the end is nigh for the UAPI patches.
Only the fbdev/framebuffer piece remains now that the SCSI stuff has
gone in.
Here are the UAPI disintegration bits for the fbdev drivers. It
appears that Florian hasn't had time to deal with my patch, but back
in December he did say he didn't mind if I pushed it forward."
Yay. No more uapi movement. And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.
* tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/video
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- Update the Xen ACPI memory and CPU hotplug locking mechanism.
- Fix PAT issues wherein various applications would not start
- Fix handling of multiple MSI as AHCI now does it.
- Fix ARM compile failures.
* tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus: fix compile failure on ARM with Xen enabled
xen/pci: We don't do multiple MSI's.
xen/pat: Disable PAT using pat_enabled value.
xen/acpi: xen cpu hotplug minor updates
xen/acpi: xen memory hotplug minor updates
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more VFS bits from Al Viro:
"Unfortunately, it looks like xattr series will have to wait until the
next cycle ;-/
This pile contains 9p cleanups and fixes (races in v9fs_fid_add()
etc), fixup for nommu breakage in shmem.c, several cleanups and a bit
more file_inode() work"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify path_get/path_put and fs_struct.c stuff
fix nommu breakage in shmem.c
cache the value of file_inode() in struct file
9p: if v9fs_fid_lookup() gets to asking server, it'd better have hashed dentry
9p: make sure ->lookup() adds fid to the right dentry
9p: untangle ->lookup() a bit
9p: double iput() in ->lookup() if d_materialise_unique() fails
9p: v9fs_fid_add() can't fail now
v9fs: get rid of v9fs_dentry
9p: turn fid->dlist into hlist
9p: don't bother with private lock in ->d_fsdata; dentry->d_lock will do just fine
more file_inode() open-coded instances
selinux: opened file can't have NULL or negative ->f_path.dentry
(In the meantime, the hlist traversal macros have changed, so this
required a semantic conflict fixup for the newly hlistified fid->dlist)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixup from Chris Mason:
"Geert and James both sent this one in, sorry guys"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs/raid56: Add missing #include <linux/vmalloc.h>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull second set of s390 patches from Martin Schwidefsky:
"The main part of this merge are Heikos uaccess patches. Together with
commit 09884964335e ("mm: do not grow the stack vma just because of an
overrun on preceding vma") the user string access is hopefully fixed
for good.
In addition some bug fixes and two cleanup patches."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/module: fix compile warning
qdio: remove unused parameters
s390/uaccess: fix kernel ds access for page table walk
s390/uaccess: fix strncpy_from_user string length check
input: disable i8042 PC Keyboard controller for s390
s390/dis: Fix invalid array size
s390/uaccess: remove pointless access_ok() checks
s390/uaccess: fix strncpy_from_user/strnlen_user zero maxlen case
s390/uaccess: shorten strncpy_from_user/strnlen_user
s390/dasd: fix unresponsive device after all channel paths were lost
s390/mm: ignore change bit for vmemmap
s390/page table dumper: add support for change-recording override bit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull second round of PARISC updates from Helge Deller:
"The most important fix in this branch is the switch of io_setup,
io_getevents and io_submit syscalls to use the available compat
syscalls when running 32bit userspace on 64bit kernel. Other than
that it's mostly removal of compile warnings."
* 'fixes-for-3.9-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix redefinition of SET_PERSONALITY
parisc: do not install modules when installing kernel
parisc: fix compile warnings triggered by atomic_sub(sizeof(),v)
parisc: check return value of down_interruptible() in hp_sdc_rtc.c
parisc: avoid unitialized variable warning in pa_memcpy()
parisc: remove unused variable 'compat_val'
parisc: switch to compat_functions of io_setup, io_getevents and io_submit
parisc: select ARCH_WANT_FRAME_POINTERS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull new ImgTec Meta architecture from James Hogan:
"This adds core architecture support for Imagination's Meta processor
cores, followed by some later miscellaneous arch/metag cleanups and
fixes which I kept separate to ease review:
- Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
- A few fixes all over, particularly for symbol prefixes
- A few privilege protection fixes
- Several cleanups (setup.c includes, split out a lot of
metag_ksyms.c)
- Fix some missing exports
- Convert hugetlb to use vm_unmapped_area()
- Copy device tree to non-init memory
- Provide dma_get_sgtable()"
* tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: (61 commits)
metag: Provide dma_get_sgtable()
metag: prom.h: remove declaration of metag_dt_memblock_reserve()
metag: copy devicetree to non-init memory
metag: cleanup metag_ksyms.c includes
metag: move mm/init.c exports out of metag_ksyms.c
metag: move usercopy.c exports out of metag_ksyms.c
metag: move setup.c exports out of metag_ksyms.c
metag: move kick.c exports out of metag_ksyms.c
metag: move traps.c exports out of metag_ksyms.c
metag: move irq enable out of irqflags.h on SMP
genksyms: fix metag symbol prefix on crc symbols
metag: hugetlb: convert to vm_unmapped_area()
metag: export clear_page and copy_page
metag: export metag_code_cache_flush_all
metag: protect more non-MMU memory regions
metag: make TXPRIVEXT bits explicit
metag: kernel/setup.c: sort includes
perf: Enable building perf tools for Meta
metag: add boot time LNKGET/LNKSET check
metag: add __init to metag_cache_probe()
...
|
