| Age | Commit message (Collapse) | Author |
|---|
|
We had a buggy release of bcachefs-tools that wasn't properly aligning
bucket sizes.
We can't ask users to reformat - and it's easy to teach the allocator to
make sure writes are properly aligned.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Previously, copygc and rebalance weren't started until the very end of
mounting, after all recvoery passes have finished.
But copygc really should be started earlier, since it may be needed for
allocations to make forward progress. Additionally, we've been seeing
occasional bug reports where starting the kthread fails due to a pending
signal - i.e. we're getting timed out by systemd (during a version
upgrade), but we're not seeing the signal until mount is about to
complete.
Additionally, we now have copygc/rebalance explicitly wait for
check_snapshots to complete (if being run); they require that for
snapshot_is_ancestor() in the data move path.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Don't use a continue; this simplifies the next patch where
run_recovery_passes() will be responsible for waking up copygc and
rebalance at the appropriate time.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
According to CXL r3.2 section 8.2.1.2, the PCI_COMMAND register fields,
including Memory Space Enable bit, have no effect on the behavior of an
RCD Upstream Port. Retaining this check may incorrectly cause
cxl_pci_probe() to fail on a valid RCD upstream Port.
While the specification is explicit only for RCD Upstream Ports, this
check is solely for accessing the RCRB, which is always mapped through
memory space. Therefore, its safe to remove the check entirely. In
practice, firmware reliably enables the Memory Space Enable bit for
RCH Downstream Ports and no failures have been observed.
Removing the check simplifies the code and avoids unnecessary
special-casing, while relying on BIOS/firmware to configure devices
correctly. Moreover, any failures due to inaccessible RCRB regions
will still be caught either in __rcrb_to_component() or while
parsing the component register block.
The following failure was observed in dmesg when the check was present:
cxl_pci 0000:7f:00.0: No component registers (-6)
Fixes: d5b1a27143cb ("cxl/acpi: Extract component registers of restricted hosts from RCRB")
Signed-off-by: Smita Koralahalli <Smita.KoralahalliChannabasappa@amd.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Link: https://patch.msgid.link/20250407192734.70631-1-Smita.KoralahalliChannabasappa@amd.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
|
|
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
found with the new enumerated_ref code
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
We've got some reports of this happening in the wild, and need a bit
more info to debug it:
https://github.com/koverstreet/bcachefs/issues/854
https://www.reddit.com/r/bcachefs/comments/1k28kjm/surprise_soft_lockup/
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
We don't require that bucket size is block size aligned (although it
should be!) - so we need to handle this in the journal code.
This fixes an assertion pop in jorunal_entry_close(), where the journal
entry overruns available space - after rounding it up to block size.
Fixes: https://github.com/koverstreet/bcachefs/issues/854
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Syzbot managed to come up with a filesystem where check/repair got
rather confused at finding a reflink pointer in the inodes btree.
Currently, the "key allowed in this btree" checks only apply at commit
time, not read time - for forwards compatibility. It seems this is too
loose.
Now, strict key type allowed checks apply:
- at commit time (no forward compatibility issues)
- for btree node pointers
- if it's a known btree, known key type, and the key type has the
"BKEY_TYPE_strict_btree_checks" flag.
This means we still have the option of using generic key types - e.g.
KEY_TYPE_error, KEY_TYPE_set - on more existing btrees in the future,
while most key types that are intended for only a specific btree get
stricter checks.
Reported-by: syzbot+baee8591f336cab0958b@syzkaller.appspotmail.com
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
We now more often do repair automatically, without the user invoking
fsck - and sometimes that can involve fixing lots of errors, so let's
avoid flooding the dmesg log.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Reported-by: syzbot+baee8591f336cab0958b@syzkaller.appspotmail.com
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Don't set JOURNAL_running until we're also calling
journal_space_available() for the first time.
If JOURNAL_running is set, shutdown will write an empty journal entry -
but this will hit an assert in journal_entry_open() if we've never
called journal_space_available().
Reported-by: syzbot+53bb24d476ef8368a7f0@syzkaller.appspotmail.com
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
I had left the warning around but as a non-fatal error to get my gcc-15
builds going, but fixed up some of the most annoying warning cases so
that it wouldn't be *too* verbose.
Because I like the _concept_ of the warning, even if I detested the
implementation to shut it up.
It turns out the implementation to shut it up is even more broken than I
thought, and my "shut up most of the warnings" patch just caused fatal
errors on gcc-14 instead.
I had tested with clang, but when I upgrade my development environment,
I try to do it on all machines because I hate having different systems
to maintain, and hadn't realized that gcc-14 now had issues.
The ACPI case is literally why I wanted to have a *type* that doesn't
trigger the warning (see commit d5d45a7f2619: "gcc-15: make
'unterminated string initialization' just a warning"), instead of
marking individual places as "__nonstring".
But gcc-14 doesn't like that __nonstring location that shut gcc-15 up,
because it's on an array of char arrays, not on one single array:
drivers/acpi/tables.c:399:1: error: 'nonstring' attribute ignored on objects of type 'const char[][4]' [-Werror=attributes]
399 | static const char table_sigs[][ACPI_NAMESEG_SIZE] __initconst __nonstring = {
| ^~~~~~
and my attempts to nest it properly with a type had failed, because of
how gcc doesn't like marking the types as having attributes, only
symbols.
There may be some trick to it, but I was already annoyed by the bad
attribute design, now I'm just entirely fed up with it.
I wish gcc had a proper way to say "this type is a *byte* array, not a
string".
The obvious thing would be to distinguish between "char []" and an
explicitly signed "unsigned char []" (as opposed to an implicitly
unsigned char, which is typically an architecture-specific default, but
for the kernel is universal thanks to '-funsigned-char').
But any "we can typedef a 8-bit type to not become a string just because
it's an array" model would be fine.
But "__attribute__((nonstring))" is sadly not that sane model.
Reported-by: Chris Clayton <chris2553@googlemail.com>
Fixes: 4b4bd8c50f48 ("gcc-15: acpi: sprinkle random '__nonstring' crumbles around")
Fixes: d5d45a7f2619 ("gcc-15: make 'unterminated string initialization' just a warning")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
The C sequence points are complicated things, and gcc-15 has apparently
added a warning for the case where an object is both used and modified
multiple times within the same sequence point.
That's a great warning.
Or rather, it would be a great warning, except gcc-15 seems to not
really be very exact about it, and doesn't notice that the modification
are to two entirely different members of the same object: the array
counter and the array entries.
So that seems kind of silly.
That said, the code that gcc complains about is unnecessarily
complicated, so moving the array counter update into a separate
statement seems like the most straightforward fix for these warnings:
drivers/net/wireless/intel/iwlwifi/mld/d3.c: In function ‘iwl_mld_set_netdetect_info’:
drivers/net/wireless/intel/iwlwifi/mld/d3.c:1102:66: error: operation on ‘netdetect_info->n_matches’ may be undefined [-Werror=sequence-point]
1102 | netdetect_info->matches[netdetect_info->n_matches++] = match;
| ~~~~~~~~~~~~~~~~~~~~~~~~~^~
drivers/net/wireless/intel/iwlwifi/mld/d3.c:1120:58: error: operation on ‘match->n_channels’ may be undefined [-Werror=sequence-point]
1120 | match->channels[match->n_channels++] =
| ~~~~~~~~~~~~~~~~~^~
side note: the code at that second warning is actively buggy, and only
works on little-endian machines that don't do strict alignment checks.
The code casts an array of integers into an array of unsigned long in
order to use our bitmap iterators. That happens to work fine on any
sane architecture, but it's still wrong.
This does *not* fix that more serious problem. This only splits the two
assignments into two statements and fixes the compiler warning. I need
to get rid of the new warnings in order to be able to actually do any
build testing.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
All of these cases are perfectly valid and good traditional C, but hit
by the "you're not NUL-terminating your byte array" warning.
And none of the cases want any terminating NUL character.
Mark them __nonstring to shut up gcc-15 (and in the case of the ak8974
magnetometer driver, I just removed the explicit array size and let gcc
expand the 3-byte and 6-byte arrays by one extra byte, because it was
the simpler change).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This removes two cases of explicit NUL padding that now causes warnings
because of '-Wunterminated-string-initialization' being part of -Wextra
in gcc-15.
Gcc is being silly in this case when it says that it truncates a NUL
terminator, because in these cases there were _multiple_ NUL characters.
But we can get rid of the warning by just simplifying the two
initializers that trigger the warning for me, so this does exactly that.
I'm not sure why the power supply code did that odd
.attr_name = #_name "\0",
pattern: it was introduced in commit 2cabeaf15129 ("power: supply: core:
Cleanup power supply sysfs attribute list"), but that 'attr_name[]'
field is an explicitly sized character array in a statically initialized
variable, and a string initializer always has a terminating NUL _and_
statically initialized character arrays are zero-padded anyway, so it
really seems to be rather extraneous belt-and-suspenders.
The zero_uuid[16] initialization in drivers/md/bcache/super.c makes
perfect sense, but it isn't necessary for the same reasons, and not
worth the new gcc warning noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is not great: I'd much rather introduce a typedef that is a "ACPI
name byte buffer", and use that to mark these special 4-byte ACPI names
that do not use NUL termination.
But as noted in the previous commit ("gcc-15: make 'unterminated string
initialization' just a warning") gcc doesn't actually seem to support
that notion, so instead you have to just mark every single array
declaration individually.
So this is not pretty, but this gets rid of the bulk of the annoying
warnings during an allmodconfig build for me.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
gcc-15 enabling -Wunterminated-string-initialization in -Wextra by
default was done with the best intentions, but the warning is still
quite broken.
What annoys me about the warning is that this is a very traditional AND
CORRECT way to initialize fixed byte arrays in C:
unsigned char hex[16] = "0123456789abcdef";
and we use this all over the kernel. And the warning is fine, but gcc
developers apparently never made a reasonable way to disable it. As is
(sadly) tradition with these things.
Yes, there's "__attribute__((nonstring))", and we have a macro to make
that absolutely disgusting syntax more palatable (ie the kernel syntax
for that monstrosity is just "__nonstring").
But that attribute is misdesigned. What you'd typically want to do is
tell the compiler that you are using a type that isn't a string but a
byte array, but that doesn't work at all:
warning: ‘nonstring’ attribute does not apply to types [-Wattributes]
and because of this fundamental mis-design, you then have to mark each
instance of that pattern.
This is particularly noticeable in our ACPI code, because ACPI has this
notion of a 4-byte "type name" that gets used all over, and is exactly
this kind of byte array.
This is a sad oversight, because the warning is useful, but really would
be so much better if gcc had also given a sane way to indicate that we
really just want a byte array type at a type level, not the broken "each
and every array definition" level.
So now instead of creating a nice "ACPI name" type using something like
typedef char acpi_name_t[4] __nonstring;
we have to do things like
char name[ACPI_NAMESEG_SIZE] __nonstring;
in every place that uses this concept and then happens to have the
typical initializers.
This is annoying me mainly because I think the warning _is_ a good
warning, which is why I'm not just turning it off in disgust. But it is
hampered by this bad implementation detail.
[ And obviously I'm doing this now because system upgrades for me are
something that happen in the middle of the release cycle: don't do it
before or during travel, or just before or during the busy merge
window period. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The old development toolchain binaries were hosted in the or1k-gcc
development github repo release page. However, now that we have all
code upstream I cut releases from stable upstream tarballs. It does not
make sense to tag the or1k-gcc github repo releases for these stable
releases.
Update the toolchain binaries URL to point to where they are now hosted
on the or1k-toolchain-build github release page.
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
The librecores.org mailing list was replaced with vger.kernel.org last
year after the old mail server went offline. Update the docs to reflect
the new list.
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Add cacheinfo support for OpenRISC.
Currently, a few CPU cache attributes pertaining to OpenRISC processors
are exposed along with other unrelated CPU attributes in the procfs file
system (/proc/cpuinfo). However, a few cache attributes remain unexposed.
Provide a mechanism that the generic cacheinfo infrastructure can employ
to expose these attributes via the sysfs file system. These attributes
can then be exposed in /sys/devices/system/cpu/cpuX/cache/indexN. Move
the implementation to pull cache attributes from the processor's
registers from arch/openrisc/kernel/setup.c with a few modifications.
This implementation is based on similar work done for MIPS and LoongArch.
Link: https://raw.githubusercontent.com/openrisc/doc/master/openrisc-arch-1.4-rev0.pdf
Signed-off-by: Sahil Siddiq <sahilcdq0@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
According to the OpenRISC architecture manual, the dcache and icache may
not be present. When these caches are present, the invalidate and flush
registers may be absent. The current implementation does not perform
checks to verify their presence before utilizing cache registers, or
invalidating and flushing cache blocks.
Introduce new functions to detect the presence of cache components and
related special-purpose registers.
There are a few places where a range of addresses have to be flushed or
invalidated and the implementation is duplicated. Introduce new utility
functions and macros that generalize this implementation and reduce
duplication.
Signed-off-by: Sahil Siddiq <sahilcdq0@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
The "cpuinfo_or1k" structure currently has identical data members for
different cache components.
Remove these fields out of struct cpuinfo_or1k and into its own struct.
This reduces duplication while keeping cpuinfo_or1k extensible so more
cache descriptors can be added in the future.
Also add a new field "sets" to the new structure.
Signed-off-by: Sahil Siddiq <sahilcdq0@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc hotfixes from Andrew Morton:
"16 hotfixes. 2 are cc:stable and the remainder address post-6.14
issues or aren't considered necessary for -stable kernels.
All patches are basically for MM although five are alterations to
MAINTAINERS"
[ Basic counting skills are clearly not a strictly necessary requirement
for kernel maintainers. - Linus ]
* tag 'mm-hotfixes-stable-2025-04-19-21-24' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
MAINTAINERS: add section for locking of mm's and VMAs
mm: vmscan: fix kswapd exit condition in defrag_mode
mm: vmscan: restore high-cpu watermark safety in kswapd
MAINTAINERS: add Pedro as reviewer to the MEMORY MAPPING section
mm/memory: move sanity checks in do_wp_page() after mapcount vs. refcount stabilization
mm, hugetlb: increment the number of pages to be reset on HVO
writeback: fix false warning in inode_to_wb()
docs: ABI: replace mcroce@microsoft.com with new Meta address
mm/gup: fix wrongly calculated returned value in fault_in_safe_writeable()
MAINTAINERS: add memory advice section
MAINTAINERS: add mmap trace events to MEMORY MAPPING
mm: memcontrol: fix swap counter leak from offline cgroup
MAINTAINERS: add MM subsection for the page allocator
MAINTAINERS: update SLAB ALLOCATOR maintainers
fs/dax: fix folio splitting issue by resetting old folio order + _nr_pages
mm/page_alloc: fix deadlock on cpu_hotplug_lock in __accept_page()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- Revert the hfs{plus} deprecation warning that's also included in this
pull request. The commit introducing the deprecation warning resides
rather early in this branch. So simply dropping it would've rebased
all other commits which I decided to avoid. Hence the revert in the
same branch
[ Background - the deprecation warning discussion resulted in people
stepping up, and so hfs{plus} will have a maintainer taking care of
it after all.. - Linus ]
- Switch CONFIG_SYSFS_SYCALL default to n and decouple from
CONFIG_EXPERT
- Fix an audit bug caused by changes to our kernel path lookup helpers
this cycle. Audit needs the parent path even if the dentry it tried
to look up is negative
- Ensure that the kernel path lookup helpers leave the passed in path
argument clean when they return an error. This is consistent with all
our other helpers
- Ensure that vfs_getattr_nosec() calls bdev_statx() so the relevant
information is available to kernel consumers as well
- Don't set a timer and call schedule() if the timer will expire
immediately in epoll
- Make netfs lookup tables with __nonstring
* tag 'vfs-6.15-rc3.fixes.2' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
Revert "hfs{plus}: add deprecation warning"
fs: move the bdex_statx call to vfs_getattr_nosec
netfs: Mark __nonstring lookup tables
eventpoll: Set epoll timeout if it's in the future
fs: ensure that *path_locked*() helpers leave passed path pristine
fs: add kern_path_locked_negative()
hfs{plus}: add deprecation warning
Kconfig: switch CONFIG_SYSFS_SYCALL default to n
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- Address translator: fix wrong include
- ChromeOS EC tunnel: fix potential NULL pointer dereference
* tag 'i2c-for-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: atr: Fix wrong include
i2c: cros-ec-tunnel: defer probe if parent EC is not present
|
|
This reverts commit ddee68c499f76ae47c011549df5be53db0057402.
There's ongoing discussion about better maintenance of at least hfsplus.
Rever the deprecation warning for now.
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Initialize hash variables in ftrace subops logic
The fix that simplified the ftrace subops logic opened a path where
some variables could be used without being initialized, and done
subtly where the compiler did not catch it. Initialize those
variables to the EMPTY_HASH, which is the default hash.
- Reinitialize the hash pointers after they are freed
Some of the hash pointers in the subop logic were freed but may still
be referenced later. To prevent use-after-free bugs, initialize them
back to the EMPTY_HASH.
- Free the ftrace hashes when they are replaced
The fix that simplified the subops logic updated some hash pointers,
but left the original hash that they were pointing to where they are
no longer used. This caused a memory leak. Free the hashes that are
pointed to by the pointers when they are replaced.
- Fix size initialization of ftrace direct function hash
The ftrace direct function hash used by BPF initialized the hash size
incorrectly. It checked the size of items to a hard coded 32, which
made the hash bit size of 5. The hash size is supposed to be limited
by the bit size of the hash, as the bitmask is allowed to be greater
than 5. Rework the size check to first pass the number of elements to
fls() and then compare that to FTRACE_HASH_MAX_BITS before allocating
the hash.
- Fix format output of ftrace_graph_ent_entry event
The field depth of the ftrace_graph_ent_entry event is of size 4 but
the output showed it as unsigned long and use "%lu". Change it to
unsigned int and use "%u" in the print format that is displayed to
user space.
- Fix the trace event filter on strings
Events can be filtered on numbers or string values. The return value
checked from strncpy_from_kernel_nofault() and
strncpy_from_user_nofault() was used to determine if reading the
strings would fault or not. It would return fault if the value was
non zero, which is basically meant that it was always considering the
read as a fault.
- Add selftest to test trace event string filtering
In order to catch the breakage of the string filtering, add a self
test to make sure that it continues to work.
* tag 'trace-v6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: selftests: Add testing a user string to filters
tracing: Fix filter string testing
ftrace: Fix type of ftrace_graph_ent_entry.depth
ftrace: fix incorrect hash size in register_ftrace_direct()
ftrace: Free ftrace hashes after they are replaced in the subops code
ftrace: Reinitialize hash to EMPTY_HASH after freeing
ftrace: Initialize variables for ftrace_startup/shutdown_subops()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
- v6.15 libcrc clean-up makes invalid configurations possible
- Fix a potential deadlock introduced during the v6.15 merge window
* tag 'nfsd-6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: decrease sc_count directly if fail to queue dl_recall
nfs: add missing selections of CONFIG_CRC32
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux
Pull rust fixes from Miguel Ojeda:
"Toolchain and infrastructure:
- Fix missing KASAN LLVM flags on first build (and fix spurious
rebuilds) by skipping '--target'
- Fix Make < 4.3 build error by using '$(pound)'
- Fix UML build error by removing 'volatile' qualifier from io
helpers
- Fix UML build error by adding 'dma_{alloc,free}_attrs()' helpers
- Clean gendwarfksyms warnings by avoiding to export '__pfx' symbols
- Clean objtool warning by adding a new 'noreturn' function for
1.86.0
- Disable 'needless_continue' Clippy lint due to new 1.86.0 warnings
- Add missing 'ffi' crate to 'generate_rust_analyzer.py'
'pin-init' crate:
- Import a couple fixes from upstream"
* tag 'rust-fixes-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux:
rust: helpers: Add dma_alloc_attrs() and dma_free_attrs()
rust: helpers: Remove volatile qualifier from io helpers
rust: kbuild: use `pound` to support GNU Make < 4.3
objtool/rust: add one more `noreturn` Rust function for Rust 1.86.0
rust: kasan/kbuild: fix missing flags on first build
rust: disable `clippy::needless_continue`
rust: kbuild: Don't export __pfx symbols
rust: pin-init: use Markdown autolinks in Rust comments
rust: pin-init: alloc: restrict `impl ZeroableOption` for `Box` to `T: Sized`
scripts: generate_rust_analyzer: Add ffi crate
|
|
Pull drm fixes from Dave Airlie:
"Easter rc3 pull request, fixes in all the usuals, amdgpu, xe, msm,
with some i915/ivpu/mgag200/v3d fixes, then a couple of bits in
dma-buf/gem.
Hopefully has no easter eggs in it.
dma-buf:
- Correctly decrement refcounter on errors
gem:
- Fix test for imported buffers
amdgpu:
- Cleaner shader sysfs fix
- Suspend fix
- Fix doorbell free ordering
- Video caps fix
- DML2 memory allocation optimization
- HDP fix
i915:
- Fix DP DSC configurations that require 3 DSC engines per pipe
xe:
- Fix LRC address being written too late for GuC
- Fix notifier vs folio deadlock
- Fix race betwen dma_buf unmap and vram eviction
- Fix debugfs handling PXP terminations unconditionally
msm:
- Display:
- Fix to call dpu_plane_atomic_check_pipe() for both SSPPs in
case of multi-rect
- Fix to validate plane_state pointer before using it in
dpu_plane_virtual_atomic_check()
- Fix to make sure dereferencing dpu_encoder_phys happens after
making sure it is valid in _dpu_encoder_trigger_start()
- Remove the remaining intr_tear_rd_ptr which we initialized to
-1 because NO_IRQ indices start from 0 now
- GPU:
- Fix IB_SIZE overflow
ivpu:
- Fix debugging
- Fixes to frequency
- Support firmware API 3.28.3
- Flush jobs upon reset
mgag200:
- Set vblank start to correct values
v3d:
- Fix Indirect Dispatch"
* tag 'drm-fixes-2025-04-19' of https://gitlab.freedesktop.org/drm/kernel: (26 commits)
drm/msm/a6xx+: Don't let IB_SIZE overflow
drm/xe/pxp: do not queue unneeded terminations from debugfs
drm/xe/dma_buf: stop relying on placement in unmap
drm/xe/userptr: fix notifier vs folio deadlock
drm/xe: Set LRC addresses before guc load
drm/mgag200: Fix value in <VBLKSTR> register
drm/gem: Internally test import_attach for imported objects
drm/amdgpu: Use the right function for hdp flush
drm/amd/display/dml2: use vzalloc rather than kzalloc
drm/amdgpu: Add back JPEG to video caps for carrizo and newer
drm/amdgpu: fix warning of drm_mm_clean
drm/amd: Forbid suspending into non-default suspend states
drm/amdgpu: use a dummy owner for sysfs triggered cleaner shaders v4
drm/i915/dp: Check for HAS_DSC_3ENGINES while configuring DSC slices
drm/i915/display: Add macro for checking 3 DSC engines
dma-buf/sw_sync: Decrement refcount on error in sw_sync_ioctl_get_deadline()
accel/ivpu: Add cmdq_id to job related logs
accel/ivpu: Show NPU frequency in sysfs
accel/ivpu: Fix the NPU's DPU frequency calculation
accel/ivpu: Update FW Boot API to version 3.28.3
...
|
|
Dave Hansen reports the following crash on a 32-bit system with
CONFIG_HIGHMEM=y and CONFIG_X86_PAE=y:
> 0xf75fe000 is the mem_map[] entry for the first page >4GB. It
> obviously wasn't allocated, thus the oops.
BUG: unable to handle page fault for address: f75fe000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
*pdpt = 0000000002da2001 *pde = 000000000300c067 *pte = 0000000000000000
Oops: Oops: 0002 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 0 Comm: swapper Not tainted 6.15.0-rc1-00288-ge618ee89561b-dirty #311 PREEMPT(undef)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
EIP: __free_pages_core+0x3c/0x74
...
Call Trace:
memblock_free_pages+0x11/0x2c
memblock_free_all+0x2ce/0x3a0
mm_core_init+0xf5/0x320
start_kernel+0x296/0x79c
i386_start_kernel+0xad/0xb0
startup_32_smp+0x151/0x154
The mem_map[] is allocated up to the end of ZONE_HIGHMEM which is defined
by max_pfn.
The bug was introduced by this recent commit:
6faea3422e3b ("arch, mm: streamline HIGHMEM freeing")
Previously, freeing of high memory was also clamped to the end of
ZONE_HIGHMEM but after this change, memblock_free_all() tries to
free memory above the of ZONE_HIGHMEM as well and that causes
access to mem_map[] entries beyond the end of the memory map.
To fix this, discard the memory after max_pfn from memblock on
32-bit systems so that core MM would be aware only of actually
usable memory.
Fixes: 6faea3422e3b ("arch, mm: streamline HIGHMEM freeing")
Reported-by: Dave Hansen <dave.hansen@intel.com>
Tested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Shevchenko <andy@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Davide Ciminaghi <ciminaghi@gnudd.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: kvm@vger.kernel.org
Link: https://lore.kernel.org/r/20250413080858.743221-1-rppt@kernel.org # discussion and submission
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
Fixes for v6.15-rc3
Display:
- Fix to call dpu_plane_atomic_check_pipe() for both SSPPs in
case of multi-rect
- Fix to validate plane_state pointer before using it in
dpu_plane_virtual_atomic_check()
- Fix to make sure dereferencing dpu_encoder_phys happens after
making sure it is valid in _dpu_encoder_trigger_start()
- Remove the remaining intr_tear_rd_ptr which we initialized
to -1 because NO_IRQ indices start from 0 now
GPU:
- Fix IB_SIZE overflow
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://lore.kernel.org/r/CAF6AEGtVKXEVdzUzFWmQE8JmK3nx_hp+ynOd-5j3vnfcU-sgOA@mail.gmail.com
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
Driver Changes:
- Fix LRC address being written too late for GuC
- Fix notifier vs folio deadlock
- Fix race betwen dma_buf unmap and vram eviction
- Fix debugfs handling PXP terminations unconditionally
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/ndinq644zenywaaycxyfqqivsb2xer4z7err3dlpalbz33jfkm@ttabzsg6wnet
|
|
Pull smb client fixes from Steve French:
- Fix hard link lease key problem when close is deferred
- Revert the socket lockdep/refcount workarounds done in cifs.ko now
that it is fixed at the socket layer
* tag '6.15-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
Revert "smb: client: fix TCP timers deadlock after rmmod"
Revert "smb: client: Fix netns refcount imbalance causing leaks and use-after-free"
smb3 client: fix open hardlink on deferred close file error
|
|
This reverts commit 99585c2192cb1ce212876e82ef01d1c98c7f4699.
Remove the acomp multibuffer tests as they are buggy.
Reported-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
IB_SIZE is only b0..b19. Starting with a6xx gen3, additional fields
were added above the IB_SIZE. Accidentially setting them can cause
badness. Fix this by properly defining the CP_INDIRECT_BUFFER packet
and using the generated builder macro to ensure unintended bits are not
set.
v2: add missing type attribute for IB_BASE
v3: fix offset attribute in xml
Reported-by: Connor Abbott <cwabbott0@gmail.com>
Fixes: a83366ef19ea ("drm/msm/a6xx: add A640/A650 to gpulist")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/643396/
|
|
endpoint maintainer
I'm currently maintaining the PCI endpoint subsystem and reviewing the
native host bridge and endpoint drivers. However, this affects my endpoint
maintainership role since I cannot merge endpoint patches that depend on
the controller drivers (which is more common). Moreover, the controller
driver patches would also benefit from a helping hand in maintaining them.
So I'd like to step up to maintain the native host bridge and endpoint
drivers together with the endpoint subsystem.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250418094905.9983-1-manivannan.sadhasivam@linaro.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
i2c-host-fixes for v6.15-rc3
- ChromeOS EC tunnel: fix potential NULL pointer dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 fixes from Ingo Molnar:
- Fix hypercall detection on Xen guests
- Extend the AMD microcode loader SHA check to Zen5, to block loading
of any unreleased standalone Zen5 microcode patches
- Add new Intel CPU model number for Bartlett Lake
- Fix the workaround for AMD erratum 1054
- Fix buggy early memory acceptance between SEV-SNP guests and the EFI
stub
* tag 'x86-urgent-2025-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/sev: Avoid shared GHCB page for early memory acceptance
x86/cpu/amd: Fix workaround for erratum 1054
x86/cpu: Add CPU model number for Bartlett Lake CPUs with Raptor Cove cores
x86/microcode/AMD: Extend the SHA check to Zen5, block loading of any unreleased standalone Zen5 microcode patches
x86/xen: Fix __xen_hypercall_setfunc()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Fix a lockdep false positive in the i8253 driver"
* tag 'timers-urgent-2025-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/i8253: Call clockevent_i8253_disable() with interrupts disabled
|
|
Calling into the MIDR checking framework from the PI code has recently
become much harder, due to the new fancy "multi-MIDR" support that
relies on tables being populated at boot time, but not that early that
they are available to the PI code. There are additional issues with
this framework, as the code really isn't position independend *at all*.
This leads to some ugly breakages, as reported by Ada.
It so appears that the only reason for the PI code to call into the
MIDR checking code is to cope with The Most Broken ARM64 System Ever,
aka Cavium ThunderX, which cannot deal with nG attributes that result
of the combination of KASLR and KPTI as a consequence of Erratum 27456.
Duplicate the check for the erratum in the PI code, removing the
dependency on the bulk of the MIDR checking framework. This allows
dropping that same check from kaslr_requires_kpti(), as the KPTI code
already relies on the ARM64_WORKAROUND_CAVIUM_27456 cap.
Fixes: c8c2647e69bed ("arm64: Make _midr_in_range_list() an exported function")
Reported-by: Ada Couprie Diaz <ada.coupriediaz@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/3d97e45a-23cf-419b-9b6f-140b4d88de7b@arm.com
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Cc: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20250418093129.1755739-1-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 perf event fixes from Ingo Molnar:
"Miscellaneous fixes and a hardware-enabling change:
- Fix Intel uncore PMU IIO free running counters on SPR, ICX and SNR
systems
- Fix Intel PEBS buffer overflow handling
- Fix skid in Intel PEBS sampling of user-space general purpose
registers
- Enable Panther Lake PMU support - similar to Lunar Lake"
* tag 'perf-urgent-2025-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Add Panther Lake support
perf/x86/intel: Allow to update user space GPRs from PEBS records
perf/x86/intel: Don't clear perf metrics overflow bit unconditionally
perf/x86/intel/uncore: Fix the scale of IIO free running counters on SPR
perf/x86/intel/uncore: Fix the scale of IIO free running counters on ICX
perf/x86/intel/uncore: Fix the scale of IIO free running counters on SNR
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc irq fixes from Ingo Molnar:
- Fix BCM2712 irqchip driver Kconfig dependencies required on the
Raspberry PI5
- Fix spurious interrupts on RZ/G3E SMARC EVK systems
- Fix crash regression on Sun/NIU hardware
- Apply MSI driver quirk for Sun Neptune chips
* tag 'irq-urgent-2025-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-bcm2712-mip: Enable driver when ARCH_BCM2835 is enabled
irqchip/renesas-rzv2h: Prevent TINT spurious interrupt
net/niu: Niu requires MSIX ENTRY_DATA fields touch before entry reads
PCI/MSI: Add an option to write MSIX ENTRY_DATA before any reads
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc core fixes from Ingo Molnar:
"Fix a genksyms related bug, triggered by recent changes to the percpu
code, and update the .clang-format file to not include obsolete
function names"
* tag 'core-urgent-2025-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genksyms: Handle typeof_unqual keyword and __seg_{fs,gs} qualifiers
clang-format: Update the ForEachMacros list for v6.15-rc1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
- lib/prime_numbers: KUnit test should not select PRIME_NUMBERS (Geert
Uytterhoeven)
- ubsan: Fix panic from test_ubsan_out_of_bounds (Mostafa Saleh)
- ubsan: Remove 'default UBSAN' from UBSAN_INTEGER_WRAP (Nathan
Chancellor)
- string: Add load_unaligned_zeropad() code path to sized_strscpy()
(Peter Collingbourne)
- kasan: Add strscpy() test to trigger tag fault on arm64 (Vincenzo
Frascino)
- Disable GCC randstruct for COMPILE_TEST
* tag 'hardening-v6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
lib/prime_numbers: KUnit test should not select PRIME_NUMBERS
ubsan: Fix panic from test_ubsan_out_of_bounds
lib/Kconfig.ubsan: Remove 'default UBSAN' from UBSAN_INTEGER_WRAP
hardening: Disable GCC randstruct for COMPILE_TEST
kasan: Add strscpy() test to trigger tag fault on arm64
string: Add load_unaligned_zeropad() code path to sized_strscpy()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
- check for both the new AND old (deprecated) setter callback when
changing GPIO direction to output
* tag 'gpio-fixes-for-v6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: Allow to use setters with return value for output-only gpios
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fixes from Rafael Wysocki:
"Add missing DVFS support flags for the Lunar Lake and Panther Lake
platforms to the int340x Intel thermal driver and fix DLVR support
for Panther Lake in it (Srinivas Pandruvada)"
* tag 'thermal-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel: int340x: Fix Panther Lake DLVR support
thermal: intel: int340x: Add missing DVFS support flags
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These are mostly cpufreq fixes, some of which address recent
regressions and some address older issues that have come to light
during the last two weeks, and a runtime PM documentation correction:
- Fix the performance-to-frequency scaling factor computation on
systems using HWP in the intel_pstate driver after a recent
incorrect update of it (Rafael Wysocki)
- Fix the usage of the CPUFREQ_NEED_UPDATE_LIMITS cpufreq driver flag
in the schedutil cpufreq governor after a recent update of it that
has caused frequency limits changes to be missed sometimes (Rafael
Wysocki)
- Address some recently discovered synchronization issues related to
frequency limits changes in the schedutil cpufreq governor and in
the cpufreq core (Rafael Wysocki)
- Fix ITMT support in the amd-pstate cpufreq driver so that it is
enabled after asym priorities have been correctly initialized for
all CPUs (K Prateek Nayak)
- Fix changing min/max limits in the amd-pstate cpufreq driver while
on the performance governor (Dhananjay Ugwekar)
- Fix a function name in the runtime PM documentation that was
previously incorrectly updated by mistake (Sakari Ailus)"
* tag 'pm-6.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Avoid using inconsistent policy->min and policy->max
cpufreq/sched: Set need_freq_update in ignore_dl_rate_limit()
cpufreq/sched: Explicitly synchronize limits_changed flag handling
cpufreq/sched: Fix the usage of CPUFREQ_NEED_UPDATE_LIMITS
Documentation: PM: runtime: Fix a reference to pm_runtime_autosuspend()
cpufreq: intel_pstate: Fix hwp_get_cpu_scaling()
cpufreq/amd-pstate: Enable ITMT support after initializing core rankings
cpufreq/amd-pstate: Fix min_limit perf and freq updation for performance governor
|
