| Age | Commit message (Collapse) | Author |
|---|
|
This is part of an effort to assign a section in MAINTAINERS to header
files that relate to Networking. In this case the files with "net" in
their name.
It seems that sonet.h is included in ATM related source files,
and thus that ATM is the most relevant section for these files.
Cc: Chas Williams <3chas3@gmail.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Let the kememdup_array() take care about multiplication and possible
overflows.
Signed-off-by: Yu Jiaoliang <yujiaoliang@vivo.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240821081447.12430-1-yujiaoliang@vivo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
GDM1 port on EN7581 SoC is connected to the lan dsa switch.
GDM{2,3,4} can be used as wan port connected to an external
phy module. Configure hw mac address registers according to the port id.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20240821-airoha-eth-wan-mac-addr-v2-1-8706d0cd6cd5@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Some CPT AF registers are per LF and others are global. Translation
of PF/VF local LF slot number to actual LF slot number is required
only for accessing perf LF registers. CPT AF global registers access
do not require any LF slot number. Also, there is no reason CPT
PF/VF to know actual lf's register offset.
Without this fix microcode loading will fail, VFs cannot be created
and hardware is not usable.
Fixes: bc35e28af789 ("octeontx2-af: replace cpt slot with lf id on reg write")
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240821070558.1020101-1-bbhushan2@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The current implementation incorrectly sets the mode bit of the PHY chip.
Bit 15 (RTL8211F_LEDCR_MODE) should not be shifted together with the
configuration nibble of a LED- it should be set independently of the
index of the LED being configured.
As a consequence, the RTL8211F LED control is actually operating in Mode A.
Fix the error by or-ing final register value to write with a const-value of
RTL8211F_LEDCR_MODE, thus setting Mode bit explicitly.
Fixes: 17784801d888 ("net: phy: realtek: Add support for PHY LEDs on RTL8211F")
Signed-off-by: Sava Jakovljev <savaj@meyersound.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://patch.msgid.link/PAWP192MB21287372F30C4E55B6DF6158C38E2@PAWP192MB2128.EURP192.PROD.OUTLOOK.COM
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
A few tests check if nettest exists in the $PATH before adding
$PWD to $PATH and re-checking. They don't discard stderr on
the first check (and nettest is built as part of selftests,
so it's pretty normal for it to not be available in system $PATH).
This leads to output noise:
which: no nettest in (/home/virtme/tools/fs/bin:/home/virtme/tools/fs/sbin:/home/virtme/tools/fs/usr/bin:/home/virtme/tools/fs/usr/sbin:/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin)
Add a common helper for the check which does silence stderr.
There is another small functional change hiding here, because pmtu.sh
and fib_rule_tests.sh used to return from the test case rather than
completely exit. Building nettest is not hard, there should be no need
to maintain the ability to selectively skip cases in its absence.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20240821012227.1398769-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The MAC only has add the TX delay and it can not be modified.
MAC and PHY are both set the TX delay cause transmission problems.
So just disable TX delay in PHY, when use rgmii to attach to
external phy, set PHY_INTERFACE_MODE_RGMII_RXID to phy drivers.
And it is does not matter to internal phy.
Fixes: bc2426d74aa3 ("net: ngbe: convert phylib to phylink")
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Cc: stable@vger.kernel.org # 6.3+
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E6759CF1387CF84C+20240820030425.93003-1-mengyuanlou@net-swift.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Ensure there is sufficient room to access the protocol field of the
VLAN header, validate it once before the flowtable lookup.
=====================================================
BUG: KMSAN: uninit-value in nf_flow_offload_inet_hook+0x45a/0x5f0 net/netfilter/nf_flow_table_inet.c:32
nf_flow_offload_inet_hook+0x45a/0x5f0 net/netfilter/nf_flow_table_inet.c:32
nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline]
nf_hook_slow+0xf4/0x400 net/netfilter/core.c:626
nf_hook_ingress include/linux/netfilter_netdev.h:34 [inline]
nf_ingress net/core/dev.c:5440 [inline]
Fixes: 4cd91f7c290f ("netfilter: flowtable: add vlan support")
Reported-by: syzbot+8407d9bb88cd4c6bf61a@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Justin Iurman says:
====================
net: ipv6: ioam6: introduce tunsrc
This series introduces a new feature called "tunsrc" (just like seg6
already does).
v3:
- address Jakub's comments
v2:
- add links to performance result figures (see patch#2 description)
- move the ipv6_addr_any() check out of the datapath
====================
Link: https://patch.msgid.link/20240817131818.11834-1-justin.iurman@uliege.be
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch provides a new feature (i.e., "tunsrc") for the tunnel (i.e.,
"encap") mode of ioam6. Just like seg6 already does, except it is
attached to a route. The "tunsrc" is optional: when not provided (by
default), the automatic resolution is applied. Using "tunsrc" when
possible has a benefit: performance. See the comparison:
- before (= "encap" mode): https://ibb.co/bNCzvf7
- after (= "encap" mode with "tunsrc"): https://ibb.co/PT8L6yq
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch prepares the next one by correcting the alignment of some
lines.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-08-20 (ice)
This series contains updates to ice driver only.
Maciej fixes issues with Rx data path on architectures with
PAGE_SIZE >= 8192; correcting page reuse usage and calculations for
last offset and truesize.
Michal corrects assignment of devlink port number to use PF id.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: use internal pf id instead of function number
ice: fix truesize operations for PAGE_SIZE >= 8192
ice: fix ICE_LAST_OFFSET formula
ice: fix page reuse when PAGE_SIZE is over 8k
====================
Link: https://patch.msgid.link/20240820215620.1245310-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the parsing code generator assumes that the yaml
specification file name and the main 'name' attribute carried
inside correspond, that is the field is the c-name representation
of the file basename.
The above assumption held true within the current tree, but will be
hopefully broken soon by the upcoming net shaper specification.
Additionally, it makes the field 'name' itself useless.
Lift the assumption, always computing the generated include file
name from the generated c file name.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Link: https://patch.msgid.link/24da5a3596d814beeb12bd7139a6b4f89756cc19.1724165948.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sean Anderson says:
====================
net: xilinx: axienet: Add statistics support
Add support for hardware statistics counters (if they are enabled) in
the AXI Ethernet driver. Unfortunately, the implementation is
complicated a bit since the hardware might only support 32-bit counters.
====================
Link: https://patch.msgid.link/20240820175343.760389-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for reading the statistics counters, if they are enabled.
The counters may be 64-bit, but we can't detect this statically as
there's no ability bit for it and the counters are read-only. Therefore,
we assume the counters are 32-bits by default. To ensure we don't miss
an overflow, we read all counters at 13-second intervals. This should be
often enough to ensure the bytes counters don't wrap at 2.5 Gbit/s.
Another complication is that the counters may be reset when the device
is reset (depending on configuration). To ensure the counters persist
across link up/down (including suspend/resume), we maintain our own
versions along with the last counter value we saw. Because we might wait
up to 100 ms for the reset to complete, we use a mutex to protect
writing hw_stats. We can't sleep in ndo_get_stats64, so we use a seqlock
to protect readers.
We don't bother disabling the refresh work when we detect 64-bit
counters. This is because the reset issue requires us to read
hw_stat_base and reset_in_progress anyway, which would still require the
seqcount. And I don't think skipping the task is worth the extra
bookkeeping.
We can't use the byte counters for either get_stats64 or
get_eth_mac_stats. This is because the byte counters include everything
in the frame (destination address to FCS, inclusive). But
rtnl_link_stats64 wants bytes excluding the FCS, and
ethtool_eth_mac_stats wants to exclude the L2 overhead (addresses and
length/type). It might be possible to calculate the byte values Linux
expects based on the frame counters, but I think it is simpler to use
the existing software counters.
get_ethtool_stats is implemented for nonstandard statistics. This
includes the aforementioned byte counters, VLAN and PFC frame
counters, and user-defined (e.g. with custom RTL) counters.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20240820175343.760389-3-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Receive Frame Rejected interrupt is asserted whenever there was a
receive error (bad FCS, bad length, etc.) or whenever the frame was
dropped due to a mismatched address. So this is really a combination of
rx_otherhost_dropped, rx_length_errors, rx_frame_errors, and
rx_crc_errors. Mismatched addresses are common and aren't really errors
at all (much like how fragments are normal on half-duplex links). To
avoid confusion, report these events as rx_dropped. This better
reflects what's going on: the packet was received by the MAC but dropped
before being processed.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://patch.msgid.link/20240820175343.760389-2-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adding the NAPI pointer to struct netdev_queue made it grow into another
cacheline, even though there was 44 bytes of padding available.
The struct was historically grouped as follows:
/* read-mostly stuff (align) */
/* ... random control path fields ... */
/* write-mostly stuff (align) */
/* ... 40 byte hole ... */
/* struct dql (align) */
It seems that people want to add control path fields after
the read only fields. struct dql looks pretty innocent
but it forces its own alignment and nothing indicates that
there is a lot of empty space above it.
Move dql above the xmit_lock. This shifts the empty space
to the end of the struct rather than in the middle of it.
Move two example fields there to set an example.
Hopefully people will now add new fields at the end of
the struct. A lot of the read-only stuff is also control
path-only, but if we move it all we'll have another hole
in the middle.
Before:
/* size: 384, cachelines: 6, members: 16 */
/* sum members: 284, holes: 3, sum holes: 100 */
After:
/* size: 320, cachelines: 5, members: 16 */
/* sum members: 284, holes: 1, sum holes: 8 */
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240820205119.1321322-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the dma_unmap_page_attrs() call in the driver's XDP_REDIRECT
code path. This should have been removed when we let the page pool
handle the DMA mapping. This bug causes the warning:
WARNING: CPU: 7 PID: 59 at drivers/iommu/dma-iommu.c:1198 iommu_dma_unmap_page+0xd5/0x100
CPU: 7 PID: 59 Comm: ksoftirqd/7 Tainted: G W 6.8.0-1010-gcp #11-Ubuntu
Hardware name: Dell Inc. PowerEdge R7525/0PYVT1, BIOS 2.15.2 04/02/2024
RIP: 0010:iommu_dma_unmap_page+0xd5/0x100
Code: 89 ee 48 89 df e8 cb f2 69 ff 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 31 d2 31 c9 31 f6 31 ff 45 31 c0 e9 ab 17 71 00 <0f> 0b 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 31 d2 31 c9
RSP: 0018:ffffab1fc0597a48 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff99ff838280c8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffffab1fc0597a78 R08: 0000000000000002 R09: ffffab1fc0597c1c
R10: ffffab1fc0597cd3 R11: ffff99ffe375acd8 R12: 00000000e65b9000
R13: 0000000000000050 R14: 0000000000001000 R15: 0000000000000002
FS: 0000000000000000(0000) GS:ffff9a06efb80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000565c34c37210 CR3: 00000005c7e3e000 CR4: 0000000000350ef0
? show_regs+0x6d/0x80
? __warn+0x89/0x150
? iommu_dma_unmap_page+0xd5/0x100
? report_bug+0x16a/0x190
? handle_bug+0x51/0xa0
? exc_invalid_op+0x18/0x80
? iommu_dma_unmap_page+0xd5/0x100
? iommu_dma_unmap_page+0x35/0x100
dma_unmap_page_attrs+0x55/0x220
? bpf_prog_4d7e87c0d30db711_xdp_dispatcher+0x64/0x9f
bnxt_rx_xdp+0x237/0x520 [bnxt_en]
bnxt_rx_pkt+0x640/0xdd0 [bnxt_en]
__bnxt_poll_work+0x1a1/0x3d0 [bnxt_en]
bnxt_poll+0xaa/0x1e0 [bnxt_en]
__napi_poll+0x33/0x1e0
net_rx_action+0x18a/0x2f0
Fixes: 578fcfd26e2a ("bnxt_en: Let the page pool manage the DMA mapping")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240820203415.168178-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric Dumazet says:
====================
ipv6: fix possible UAF in output paths
First patch fixes an issue spotted by syzbot, and the two
other patches fix error paths after skb_expand_head()
adoption.
====================
Link: https://patch.msgid.link/20240820160859.3786976-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If skb_expand_head() returns NULL, skb has been freed
and the associated dst/idev could also have been freed.
We must use rcu_read_lock() to prevent a possible UAF.
Fixes: 0c9f227bee11 ("ipv6: use skb_expand_head in ip6_xmit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vasily Averin <vasily.averin@linux.dev>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20240820160859.3786976-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If skb_expand_head() returns NULL, skb has been freed
and associated dst/idev could also have been freed.
We need to hold rcu_read_lock() to make sure the dst and
associated idev are alive.
Fixes: 5796015fa968 ("ipv6: allocate enough headroom in ip6_finish_output2()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vasily Averin <vasily.averin@linux.dev>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20240820160859.3786976-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported an UAF in ip6_send_skb() [1]
After ip6_local_out() has returned, we no longer can safely
dereference rt, unless we hold rcu_read_lock().
A similar issue has been fixed in commit
a688caa34beb ("ipv6: take rcu lock in rawv6_send_hdrinc()")
Another potential issue in ip6_finish_output2() is handled in a
separate patch.
[1]
BUG: KASAN: slab-use-after-free in ip6_send_skb+0x18d/0x230 net/ipv6/ip6_output.c:1964
Read of size 8 at addr ffff88806dde4858 by task syz.1.380/6530
CPU: 1 UID: 0 PID: 6530 Comm: syz.1.380 Not tainted 6.11.0-rc3-syzkaller-00306-gdf6cbc62cc9b #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/06/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:93 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:119
print_address_description mm/kasan/report.c:377 [inline]
print_report+0x169/0x550 mm/kasan/report.c:488
kasan_report+0x143/0x180 mm/kasan/report.c:601
ip6_send_skb+0x18d/0x230 net/ipv6/ip6_output.c:1964
rawv6_push_pending_frames+0x75c/0x9e0 net/ipv6/raw.c:588
rawv6_sendmsg+0x19c7/0x23c0 net/ipv6/raw.c:926
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x1a6/0x270 net/socket.c:745
sock_write_iter+0x2dd/0x400 net/socket.c:1160
do_iter_readv_writev+0x60a/0x890
vfs_writev+0x37c/0xbb0 fs/read_write.c:971
do_writev+0x1b1/0x350 fs/read_write.c:1018
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f936bf79e79
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f936cd7f038 EFLAGS: 00000246 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 00007f936c115f80 RCX: 00007f936bf79e79
RDX: 0000000000000001 RSI: 0000000020000040 RDI: 0000000000000004
RBP: 00007f936bfe7916 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007f936c115f80 R15: 00007fff2860a7a8
</TASK>
Allocated by task 6530:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3f/0x80 mm/kasan/common.c:68
unpoison_slab_object mm/kasan/common.c:312 [inline]
__kasan_slab_alloc+0x66/0x80 mm/kasan/common.c:338
kasan_slab_alloc include/linux/kasan.h:201 [inline]
slab_post_alloc_hook mm/slub.c:3988 [inline]
slab_alloc_node mm/slub.c:4037 [inline]
kmem_cache_alloc_noprof+0x135/0x2a0 mm/slub.c:4044
dst_alloc+0x12b/0x190 net/core/dst.c:89
ip6_blackhole_route+0x59/0x340 net/ipv6/route.c:2670
make_blackhole net/xfrm/xfrm_policy.c:3120 [inline]
xfrm_lookup_route+0xd1/0x1c0 net/xfrm/xfrm_policy.c:3313
ip6_dst_lookup_flow+0x13e/0x180 net/ipv6/ip6_output.c:1257
rawv6_sendmsg+0x1283/0x23c0 net/ipv6/raw.c:898
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x1a6/0x270 net/socket.c:745
____sys_sendmsg+0x525/0x7d0 net/socket.c:2597
___sys_sendmsg net/socket.c:2651 [inline]
__sys_sendmsg+0x2b0/0x3a0 net/socket.c:2680
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 45:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3f/0x80 mm/kasan/common.c:68
kasan_save_free_info+0x40/0x50 mm/kasan/generic.c:579
poison_slab_object+0xe0/0x150 mm/kasan/common.c:240
__kasan_slab_free+0x37/0x60 mm/kasan/common.c:256
kasan_slab_free include/linux/kasan.h:184 [inline]
slab_free_hook mm/slub.c:2252 [inline]
slab_free mm/slub.c:4473 [inline]
kmem_cache_free+0x145/0x350 mm/slub.c:4548
dst_destroy+0x2ac/0x460 net/core/dst.c:124
rcu_do_batch kernel/rcu/tree.c:2569 [inline]
rcu_core+0xafd/0x1830 kernel/rcu/tree.c:2843
handle_softirqs+0x2c4/0x970 kernel/softirq.c:554
__do_softirq kernel/softirq.c:588 [inline]
invoke_softirq kernel/softirq.c:428 [inline]
__irq_exit_rcu+0xf4/0x1c0 kernel/softirq.c:637
irq_exit_rcu+0x9/0x30 kernel/softirq.c:649
instr_sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1043 [inline]
sysvec_apic_timer_interrupt+0xa6/0xc0 arch/x86/kernel/apic/apic.c:1043
asm_sysvec_apic_timer_interrupt+0x1a/0x20 arch/x86/include/asm/idtentry.h:702
Last potentially related work creation:
kasan_save_stack+0x3f/0x60 mm/kasan/common.c:47
__kasan_record_aux_stack+0xac/0xc0 mm/kasan/generic.c:541
__call_rcu_common kernel/rcu/tree.c:3106 [inline]
call_rcu+0x167/0xa70 kernel/rcu/tree.c:3210
refdst_drop include/net/dst.h:263 [inline]
skb_dst_drop include/net/dst.h:275 [inline]
nf_ct_frag6_queue net/ipv6/netfilter/nf_conntrack_reasm.c:306 [inline]
nf_ct_frag6_gather+0xb9a/0x2080 net/ipv6/netfilter/nf_conntrack_reasm.c:485
ipv6_defrag+0x2c8/0x3c0 net/ipv6/netfilter/nf_defrag_ipv6_hooks.c:67
nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline]
nf_hook_slow+0xc3/0x220 net/netfilter/core.c:626
nf_hook include/linux/netfilter.h:269 [inline]
__ip6_local_out+0x6fa/0x800 net/ipv6/output_core.c:143
ip6_local_out+0x26/0x70 net/ipv6/output_core.c:153
ip6_send_skb+0x112/0x230 net/ipv6/ip6_output.c:1959
rawv6_push_pending_frames+0x75c/0x9e0 net/ipv6/raw.c:588
rawv6_sendmsg+0x19c7/0x23c0 net/ipv6/raw.c:926
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x1a6/0x270 net/socket.c:745
sock_write_iter+0x2dd/0x400 net/socket.c:1160
do_iter_readv_writev+0x60a/0x890
Fixes: 0625491493d9 ("ipv6: ip6_push_pending_frames() should increment IPSTATS_MIB_OUTDISCARDS")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20240820160859.3786976-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netpoll_poll_disable() and netpoll_poll_enable() are only used
from core networking code, there is no need to export them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240820162053.3870927-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BIT() is unsigned long but ->pu.flg_msk and ->pu.flg_val are u64 type.
On 32 bit systems, unsigned long is a u32 and the mismatch between u32
and u64 will break things for the high 32 bits.
Fixes: 9a4c07aaa0f5 ("ice: add parser execution main loop")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/ddc231a8-89c1-4ff4-8704-9198bcb41f8d@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
err varibale will be set everytime,like -ENOBUFS and in if (err < 0),
when code gets into this path. This check will just slowdown
the execution and that's all.
Signed-off-by: Xi Huang <xuiagnh@gmail.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/20240820115442.49366-1-xuiagnh@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Source the ethtool library from the correct path and avoid the following
error:
./ethtool_lanes.sh: line 14: ./../../../net/forwarding/ethtool_lib.sh: No such file or directory
Fixes: 40d269c000bd ("selftests: forwarding: Move several selftests")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/2112faff02e536e1ac14beb4c2be09c9574b90ae.1724150067.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240820075047.681223-1-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240820074805.680674-1-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
Remove unnecessary flex-array member `data[]`, and with this fix
the following warnings:
drivers/nfc/pn533/usb.c:268:38: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/nfc/pn533/usb.c:275:38: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/ZsPw7+6vNoS651Cb@elsanto
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When assembling fraglist GSO packets, udp4_gro_complete does not set
skb->csum_start, which makes the extra validation in __udp_gso_segment fail.
Fixes: 89add40066f9 ("net: drop bad gso csum_start and offset in virtio_net_hdr")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240819150621.59833-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Ilpo Järvinen:
- ISST: Fix an error-handling corner case
- platform/surface: aggregator: Minor corner case fix and new HW
support
* tag 'platform-drivers-x86-v6.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: ISST: Fix return value on last invalid resource
platform/surface: aggregator: Fix warning when controller is destroyed in probe
platform/surface: aggregator_registry: Add support for Surface Laptop 6
platform/surface: aggregator_registry: Add fan and thermal sensor support for Surface Laptop 5
platform/surface: aggregator_registry: Add support for Surface Laptop Studio 2
platform/surface: aggregator_registry: Add support for Surface Laptop Go 3
platform/surface: aggregator_registry: Add Support for Surface Pro 10
platform/x86: asus-wmi: Add quirk for ROG Ally X
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
"As I mentioned in the merge window pull request, there is a regression
which could cause system hang due to page migration. The corresponding
fix landed upstream through MM tree last week (commit 2e6506e1c4ee:
"mm/migrate: fix deadlock in migrate_pages_batch() on large folios"),
therefore large folios can be safely allowed for compressed inodes and
stress tests have been running on my fleet for over 20 days without
any regression. Users have explicitly requested this for months, so
let's allow large folios for EROFS full cases now for wider testing.
Additionally, there is a fix which addresses invalid memory accesses
on a failure path triggered by fault injection and two minor cleanups
to simplify the codebase.
Summary:
- Allow large folios on compressed inodes
- Fix invalid memory accesses if z_erofs_gbuf_growsize() partially
fails
- Two minor cleanups"
* tag 'erofs-for-6.11-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix out-of-bound access when z_erofs_gbuf_growsize() partially fails
erofs: allow large folios for compressed files
erofs: get rid of check_layout_compatibility()
erofs: simplify readdir operation
|
|
WWAN device is programmed to boot in normal mode or fastboot mode,
when triggering a device reset through ACPI call or fastboot switch
command. Maintain state machine synchronization and reprobe logic
after a device reset.
The PCIe device reset triggered by several ways.
E.g.:
- fastboot: echo "fastboot_switching" > /sys/bus/pci/devices/${bdf}/t7xx_mode.
- reset: echo "reset" > /sys/bus/pci/devices/${bdf}/t7xx_mode.
- IRQ: PCIe device request driver to reset itself by an interrupt request.
Use pci_reset_function() as a generic way to reset device, save and
restore the PCIe configuration before and after reset device to ensure
the reprobe process.
Suggestion from Bjorn:
Link: https://lore.kernel.org/all/20230127133034.GA1364550@bhelgaas/
Signed-off-by: Jinjian Song <jinjian.song@fibocom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull smb server fixes from Steve French:
- important reconnect fix
- fix for memcpy issues on mount
- two minor cleanup patches
* tag '6.11-rc4-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: Replace one-element arrays with flexible-array members
ksmbd: fix spelling mistakes in documentation
ksmbd: fix race condition between destroy_previous_session() and smb2 operations()
ksmbd: Use unsafe_memcpy() for ntlm_negotiate
|
|
Rather than print an error even when we get -EPROBE_DEFER, use
dev_err_probe() to filter out those messages.
Link: https://github.com/openwrt/openwrt/pull/11680
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240820004436.224603-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Matthieu Baerts says:
====================
mptcp: pm: fix IDs not being reusable
Here are more fixes for the MPTCP in-kernel path-manager. In this
series, the fixes are around the endpoint IDs not being reusable for
on-going connections when re-creating endpoints with previously used IDs.
- Patch 1 fixes this case for endpoints being used to send ADD_ADDR.
Patch 2 validates this fix. The issue is present since v5.10.
- Patch 3 fixes this case for endpoints being used to establish new
subflows. Patch 4 validates this fix. The issue is present since v5.10.
- Patch 5 fixes this case when all endpoints are flushed. Patch 6
validates this fix. The issue is present since v5.13.
- Patch 7 removes a helper that is confusing, and introduced in v5.10.
It helps simplifying the next patches.
- Patch 8 makes sure a 'subflow' counter is only decremented when
removing a 'subflow' endpoint. Can be backported up to v5.13.
- Patch 9 is similar, but for a 'signal' counter. Can be backported up
to v5.10.
- Patch 10 checks the last max accepted ADD_ADDR limit before accepting
new ADD_ADDR. For v5.10 as well.
- Patch 11 removes a wrong restriction for the userspace PM, added
during a refactoring in v6.5.
- Patch 12 makes sure the fullmesh mode sets the ID 0 when a new subflow
using the source address of the initial subflow is created. Patch 13
covers this case. This issue is present since v5.15.
- Patch 14 avoid possible UaF when selecting an address from the
endpoints list.
====================
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-0-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
select_local_address() and select_signal_address() both select an
endpoint entry from the list inside an RCU protected section, but return
a reference to it, to be read later on. If the entry is dereferenced
after the RCU unlock, reading info could cause a Use-after-Free.
A simple solution is to copy the required info while inside the RCU
protected section to avoid any risk of UaF later. The address ID might
need to be modified later to handle the ID0 case later, so a copy seems
OK to deal with.
Reported-by: Paolo Abeni <pabeni@redhat.com>
Closes: https://lore.kernel.org/45cd30d3-7710-491c-ae4d-a1368c00beb1@redhat.com
Fixes: 01cacb00b35c ("mptcp: add netlink-based PM")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-14-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This case was not covered, and the wrong ID was set before the previous
commit.
The rest is not modified, it is just that it will increase the code
coverage.
The right address ID can be verified by looking at the packet traces. We
could automate that using Netfilter with some cBPF code for example, but
that's always a bit cryptic. Packetdrill seems better fitted for that.
Fixes: 4f49d63352da ("selftests: mptcp: add fullmesh testcases")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-13-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When reacting upon the reception of an ADD_ADDR, the in-kernel PM first
looks for fullmesh endpoints. If there are some, it will pick them,
using their entry ID.
It should set the ID 0 when using the endpoint corresponding to the
initial subflow, it is a special case imposed by the MPTCP specs.
Note that msk->mpc_endpoint_id might not be set when receiving the first
ADD_ADDR from the server. So better to compare the addresses.
Fixes: 1a0d6136c5f0 ("mptcp: local addresses fullmesh")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-12-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ID 0 is specific per MPTCP connections. The per netns entries cannot
have this special ID 0 then.
But that's different for the userspace PM where the entries are per
connection, they can then use this special ID 0.
Fixes: f40be0db0b76 ("mptcp: unify pm get_flags_and_ifindex_by_id")
Cc: stable@vger.kernel.org
Acked-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-11-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The limits might have changed in between, it is best to check them
before accepting new ADD_ADDR.
Fixes: d0876b2284cf ("mptcp: add the incoming RM_ADDR support")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-10-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adding the following warning ...
WARN_ON_ONCE(msk->pm.add_addr_accepted == 0)
... before decrementing the add_addr_accepted counter helped to find a
bug when running the "remove single subflow" subtest from the
mptcp_join.sh selftest.
Removing a 'subflow' endpoint will first trigger a RM_ADDR, then the
subflow closure. Before this patch, and upon the reception of the
RM_ADDR, the other peer will then try to decrement this
add_addr_accepted. That's not correct because the attached subflows have
not been created upon the reception of an ADD_ADDR.
A way to solve that is to decrement the counter only if the attached
subflow was an MP_JOIN to a remote id that was not 0, and initiated by
the host receiving the RM_ADDR.
Fixes: d0876b2284cf ("mptcp: add the incoming RM_ADDR support")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-9-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adding the following warning ...
WARN_ON_ONCE(msk->pm.local_addr_used == 0)
... before decrementing the local_addr_used counter helped to find a bug
when running the "remove single address" subtest from the mptcp_join.sh
selftests.
Removing a 'signal' endpoint will trigger the removal of all subflows
linked to this endpoint via mptcp_pm_nl_rm_addr_or_subflow() with
rm_type == MPTCP_MIB_RMSUBFLOW. This will decrement the local_addr_used
counter, which is wrong in this case because this counter is linked to
'subflow' endpoints, and here it is a 'signal' endpoint that is being
removed.
Now, the counter is decremented, only if the ID is being used outside
of mptcp_pm_nl_rm_addr_or_subflow(), only for 'subflow' endpoints, and
if the ID is not 0 -- local_addr_used is not taking into account these
ones. This marking of the ID as being available, and the decrement is
done no matter if a subflow using this ID is currently available,
because the subflow could have been closed before.
Fixes: 06faa2271034 ("mptcp: remove multi addresses and subflows in PM")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-8-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This helper is confusing. It is in pm.c, but it is specific to the
in-kernel PM and it cannot be used by the userspace one. Also, it simply
calls one in-kernel specific function with the PM lock, while the
similar mptcp_pm_remove_addr() helper requires the PM lock.
What's left is the pr_debug(), which is not that useful, because a
similar one is present in the only function called by this helper:
mptcp_pm_nl_rm_subflow_received()
After these modifications, this helper can be marked as 'static', and
the lock can be taken only once in mptcp_pm_flush_addrs_and_subflows().
Note that it is not a bug fix, but it will help backporting the
following commits.
Fixes: 0ee4261a3681 ("mptcp: implement mptcp_pm_remove_subflow")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-7-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After having flushed endpoints that didn't cause the creation of new
subflows, it is important to check endpoints can be re-created, re-using
previously used IDs.
Before the previous commit, the client would not have been able to
re-create the subflow that was previously rejected.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
Fixes: 06faa2271034 ("mptcp: remove multi addresses and subflows in PM")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-6-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If no subflows are attached to the 'subflow' endpoints that are being
flushed, the corresponding addr IDs will not be marked as available
again.
Mark all ID as being available when flushing all the 'subflow'
endpoints, and reset local_addr_used counter to cover these cases.
Note that mptcp_pm_remove_addrs_and_subflows() helper is only called for
flushing operations, not to remove a specific set of addresses and
subflows.
Fixes: 06faa2271034 ("mptcp: remove multi addresses and subflows in PM")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-5-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This test extends "delete and re-add" to validate the previous commit. A
new 'subflow' endpoint is added, but the subflow request will be
rejected. The result is that no subflow will be established from this
address.
Later, the endpoint is removed and re-added after having cleared the
firewall rule. Before the previous commit, the client would not have
been able to create this new subflow.
While at it, extra checks have been added to validate the expected
numbers of MPJ and RM_ADDR.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
Fixes: b6c08380860b ("mptcp: remove addr and subflow in PM netlink")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-4-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If no subflow is attached to the 'subflow' endpoint that is being
removed, the addr ID will not be marked as available again.
Mark the linked ID as available when removing the 'subflow' endpoint if
no subflow is attached to it.
While at it, the local_addr_used counter is decremented if the ID was
marked as being used to reflect the reality, but also to allow adding
new endpoints after that.
Fixes: b6c08380860b ("mptcp: remove addr and subflow in PM netlink")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-3-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This test extends "delete re-add signal" to validate the previous
commit. An extra address is announced by the server, but this address
cannot be used by the client. The result is that no subflow will be
established to this address.
Later, the server will delete this extra endpoint, and set a new one,
with a valid address, but re-using the same ID. Before the previous
commit, the server would not have been able to announce this new
address.
While at it, extra checks have been added to validate the expected
numbers of MPJ, ADD_ADDR and RM_ADDR.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
Fixes: b6c08380860b ("mptcp: remove addr and subflow in PM netlink")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-2-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If no subflow is attached to the 'signal' endpoint that is being
removed, the addr ID will not be marked as available again.
Mark the linked ID as available when removing the address entry from the
list to cover this case.
Fixes: b6c08380860b ("mptcp: remove addr and subflow in PM netlink")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240819-net-mptcp-pm-reusing-id-v1-1-38035d40de5b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
