| Age | Commit message (Collapse) | Author |
|---|
|
6e28b000825d ("net: Fix vti use case with oif in dst lookups for IPv6")
is missing the checks on FLOWI_FLAG_SKIP_NH_OIF. Add them.
Fixes: 42a7b32b73d6 ("xfrm: Add oif to dst lookups")
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default fix broadcast window size is currently set to 20 packets.
This is a very low value, set at a time when we were still testing on
10 Mb/s hubs, and a change to it is long overdue.
Commit 7845989cb4b3da1db ("net: tipc: fix stall during bclink wakeup procedure")
revealed a problem with this low value. For messages of importance LOW,
the backlog queue limit will be calculated to 30 packets, while a
single, maximum sized message of 66000 bytes, carried across a 1500 MTU
network consists of 46 packets.
This leads to the following scenario (among others leading to the same
situation):
1: Msg 1 of 46 packets is sent. 20 packets go to the transmit queue, 26
packets to the backlog queue.
2: Msg 2 of 46 packets is attempted sent, but rejected because there is
no more space in the backlog queue at this level. The sender is added
to the wakeup queue with a "pending packets chain size" number of 46.
3: Some packets in the transmit queue are acked and released. We try to
wake up the sender, but the pending size of 46 is bigger than the LOW
wakeup limit of 30, so this doesn't happen.
5: Subsequent acks releases all the remaining buffers. Each time we test
for the wakeup criteria and find that 46 still is larger than 30,
even after both the transmit and the backlog queues are empty.
6: The sender is never woken up and given a chance to send its message.
He is stuck.
We could now loosen the wakeup criteria (used by link_prepare_wakeup())
to become equal to the send criteria (used by tipc_link_xmit()), i.e.,
by ignoring the "pending packets chain size" value altogether, or we can
just increase the queue limits so that the criteria can be satisfied
anyway. There are good reasons (potentially multiple waiting senders) to
not opt for the former solution, so we choose the latter one.
This commit fixes the problem by giving the broadcast link window a
default value of 50 packets. We also introduce a new minimum link
window size BCLINK_MIN_WIN of 32, which is enough to always avoid the
described situation. Finally, in order to not break any existing users
which may set the window explicitly, we enforce that the window is set
to the new minimum value in case the user is trying to set it to
anything lower.
Fixes: 7845989cb4b3da1db ("net: tipc: fix stall during bclink wakeup procedure")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 8eb934591f8b ("btrfs: check unsupported filters in balance
arguments") adds a jump to exit label out_bargs in case the argument
check fails. At this point in addition to the bargs memory, the
memory for struct btrfs_balance_control has already been allocated.
Ownership of bctl is passed to btrfs_balance() in the good case,
thus the memory is not freed due to the introduced jump. Make sure
that the memory gets freed in any case as necessary. Detected by
Coverity CID 1328378.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
into drm-fixes
Just a crash fix for radeon and amdgpu if the user has forcibly disabled
dpm and tries to access the pwm sysfs controls.
* 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: add missing dpm check for KV dpm late init
drm/amdgpu/dpm: don't add pwm attributes if DPM is disabled
drm/radeon/dpm: don't add pwm attributes if DPM is disabled
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
The revert dance could use some explanation: we had stuff fixed in
-next, and initially backported one commit to v4.3. Now, turns out we
need more fixes, and we could cherry-pick them all without conflicts if
we reverted the backported one first. So did that to not have to edit
and backport them all.
* tag 'drm-intel-fixes-2015-10-16' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Add primary plane to mask if it's visible
drm/i915: Move sprite/cursor plane disable to intel_sanitize_crtc()
drm/i915: Assign hwmode after encoder state readout
Revert "drm/i915: Add primary plane to mask if it's visible"
drm/i915: Deny wrapping an userptr into a framebuffer
drm/i915: Enable DPLL VGA mode before P1/P2 divider write
drm/i915: Restore lost DPLL register write on gen2-4
drm/i915: Flush pipecontrol post-sync writes
drm/i915: Fix kerneldoc for i915_gem_shrink_all
|
|
Currently we do not validate rtas.entry before calling enter_rtas(). This
leads to a kernel oops when user space calls rtas system call on a powernv
platform (see below). This patch adds code to validate rtas.entry before
making enter_rtas() call.
Oops: Exception in kernel mode, sig: 4 [#1]
SMP NR_CPUS=1024 NUMA PowerNV
task: c000000004294b80 ti: c0000007e1a78000 task.ti: c0000007e1a78000
NIP: 0000000000000000 LR: 0000000000009c14 CTR: c000000000423140
REGS: c0000007e1a7b920 TRAP: 0e40 Not tainted (3.18.17-340.el7_1.pkvm3_1_0.2400.1.ppc64le)
MSR: 1000000000081000 <HV,ME> CR: 00000000 XER: 00000000
CFAR: c000000000009c0c SOFTE: 0
NIP [0000000000000000] (null)
LR [0000000000009c14] 0x9c14
Call Trace:
[c0000007e1a7bba0] [c00000000041a7f4] avc_has_perm_noaudit+0x54/0x110 (unreliable)
[c0000007e1a7bd80] [c00000000002ddc0] ppc_rtas+0x150/0x2d0
[c0000007e1a7be30] [c000000000009358] syscall_exit+0x0/0x98
Cc: stable@vger.kernel.org # v3.2+
Fixes: 55190f88789a ("powerpc: Add skeleton PowerNV platform")
Reported-by: NAGESWARA R. SASTRY <nasastry@in.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
[mpe: Reword change log, trim oops, and add stable + fixes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
into drm-fixes
Just one fix from Ilia to resolve various issues that have resulted from
buffer eviction.
* 'linux-4.3' of git://anongit.freedesktop.org/nouveau/linux-2.6:
drm/nouveau/gem: return only valid domain when there's only one
|
|
On nv50+, we restrict the valid domains to just the one where the buffer
was originally created. However after the buffer is evicted to system
memory, we might move it back to a different domain that was not
originally valid. When sharing the buffer and retrieving its GEM_INFO
data, we still want the domain that will be valid for this buffer in a
pushbuf, not the one where it currently happens to be.
This resolves fdo#92504 and several others. These are due to suspend
evicting all buffers, making it more likely that they temporarily end up
in the wrong place.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92504
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
In Linux 4.3-rc5, there is an error case in drm_dp_get_branch_device
that returns without releasing mgr->lock, resulting a spew of kernel
messages about a kernel work function possibly having leaked a mutex
and presumably more serious adverse consequences later. This patch
changes the error to "goto out" to unlock the mutex before returning.
[airlied: grabbed from drm-next as it fixes something we've seen]
Signed-off-by: Adam J. Richter <adam_richter2004@yahoo.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Pull intel-iommu bugfix from David Woodhouse:
"This contains a single fix, for when the IOMMU API is used to overlay
an existing mapping comprised of 4KiB pages, with a mapping that can
use superpages.
For the *first* superpage in the new mapping, we were correctly¹
freeing the old bottom-level page table page and clearing the link to
it, before installing the superpage. For subsequent superpages,
however, we weren't. This causes a memory leak, and a warning about
setting a PTE which is already set.
¹ Well, not *entirely* correctly. We just free the page table pages
right there and then, which is wrong. In fact they should only be
freed *after* the IOTLB is flushed so we know the hardware will no
longer be looking at them.... and in fact I note that the IOTLB
flush is completely missing from the intel_iommu_map() code path,
although it needs to be there if it's permitted to overwrite
existing mappings.
Fixing those is somewhat more intrusive though, and will probably
need to wait for 4.4 at this point"
* tag 'for-linus-20151021' of git://git.infradead.org/intel-iommu:
iommu/vt-d: fix range computation when making room for large pages
|
|
Pull MMC bugfix from Ulf Hansson:
"Here's yet another MMC fix intended for v4.3 rc7. I don't expect to
send any further pull requests for 4.3 rc[n].
MMC core:
- Don't re-tune in the reset sequence to allow re-init of the card"
* tag 'mmc-v4.3-rc5' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: core: Fix init_card in 52Mhz
|
|
ib_send_cm_sidr_rep could sometimes erase the node from the sidr
(depending on errors in the process). Since ib_send_cm_sidr_rep is
called both from cm_sidr_req_handler and cm_destroy_id, cm_id_priv
could be either erased from the rb_tree twice or not erased at all.
Fixing that by making sure it's erased only once before freeing
cm_id_priv.
Fixes: a977049dacde ('[PATCH] IB: Add the kernel CM implementation')
Signed-off-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This commit addresses some stability problems with the command buffer
submission code recently introduced:
1) Make the vmw_cmdbuf_man_process() function handle reruns internally to
avoid losing interrupts if the caller forgets to rerun on -EAGAIN.
2) Handle default command buffer allocations using inline command buffers.
This avoids rare allocation deadlocks.
3) In case of command buffer errors we might lose fence submissions.
Therefore send a new fence after each command buffer error. This will help
avoid lengthy fence waits.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
A late round of KVM/ARM fixes for v4.3-rc7, fixing:
- A bug where level-triggered interrupts lowered from userspace
are still routed to the guest
- A memory leak an a failed initialization path
- A build error under certain configurations
- Several timer bugs introduced with moving the timer to the active
state handling instead of the masking trick.
|
|
Merge "mvebu fixes for 4.3 (part 2)" from Gregory CLEMENT:
Fix wrong compatible for A385 DB AP preventing using suspend
* tag 'mvebu-fixes-4.3-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: correct a385-db-ap compatible string
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung 2nd fixes for v4.3" from Kukjin Kim:
- fix SOC detection of exynos thermal on exynos5260
- fix audio card detection on Peach boards
- fix double of_node_put() when parsing child power domains
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
thermal: exynos: Fix register read in TMU
ARM: dts: Fix audio card detection on Peach boards
ARM: EXYNOS: Fix double of_node_put() when parsing child power domains
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Fixes for omaps for v4.3-rc cycle" from Tony Lindgren:
- Fix oops with LPAE and moew than 2GB of memory by enabling
ZONE_DMA for LPAE. Probably no need for stable on this one as we
only recently ran into this with the mainline kernel
- Fix imprecise external abort caused by bogus SRAM init. This affects
dm814x recently merged, so no need for stable on this one AFAIK
* tag 'omap-for-v4.3/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix imprecise external abort caused by bogus SRAM init
ARM: OMAP2+: Fix oops with LPAE and more than 2GB of memory
|
|
This is decrementing the pointer, instead of the value stored in the
pointer. KASan detects it as an out of bounds reference.
Reported-by: "Berry Cheng 程君(成淼)" <chengmiao.cj@alibaba-inc.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sometimes xennet_create_queues() may failed to created all requested
queues, we need to update num_queues to real created to avoid NULL
pointer dereference.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
reset transport and unlock if misc_register failed.
Signed-off-by: Gao feng <omarapazanadi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Philipp Kirchhofer says:
====================
net: mv643xx_eth: TSO TX data corruption fixes
as previously discussed [1] the mv643xx_eth driver has some
issues with data corruption when using TCP segmentation offload (TSO).
The following patch set improves this situation by fixing two data
corruption bugs in the TSO TX path.
Before applying the patches repeatedly accessing large files located on
a SMB share on my NSA325 NAS with TSO enabled resulted in different
hash sums, which confirmed that data corruption is happening during
file transfer. After applying the patches the hash sums were the same.
As this is my first patch submission please feel free to point out any
issues with the patch set.
[1] http://thread.gmane.org/gmane.linux.network/336530
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To prevent a race between the TX DMA engine and the CPU the writing of the
first transmit descriptor must be deferred until all following descriptors
have been updated. The network card may otherwise start transmitting before
all packet descriptors are set up correctly, which leads to data corruption
or an aborted transmit operation.
This deferral is already done in the non-TSO TX path, implement it also in
the TSO TX path.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TX DMA engine requires that buffers with a size of 8 bytes or smaller
must be 64 bit aligned. This requirement may be violated when doing TSO,
as in this case larger skb frags can be broken up and transmitted in small
parts with then inappropriate alignment.
Fix this by checking for proper alignment before handing a buffer to the
DMA engine. If the data is misaligned realign it by copying it into the
TSO header data area.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cgwb_bdi_destroy()
a20135ffbc44 ("writeback: don't drain bdi_writeback_congested on bdi
destruction") added rbtree_postorder_for_each_entry_safe() which is
used to remove all entries; however, according to Cody, the iterator
isn't safe against operations which may rebalance the tree. Fix it by
switching to repeatedly removing rb_first() until empty.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Cody P Schafer <dev@codyps.com>
Fixes: a20135ffbc44 ("writeback: don't drain bdi_writeback_congested on bdi destruction")
Link: http://lkml.kernel.org/g/1443997973-1700-1-git-send-email-dev@codyps.com
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Heiko Schocher says:
====================
net, phy, smsc: add posibility to disable energy detect mode
On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Therefore the property "smsc,disable-energy-detect" is
introduced.
Patch 1 introduces phy-handle support for the ti,cpsw
driver. This is needed now for the smsc phy.
Patch 2 adds the disable energy mode functionality
to the smsc phy
Changes in v2:
- add comments from Florian Fainelli
- I did not change disable property name into enable
because I fear to break existing behaviour
- add smsc vendor prefix
- remove CONFIG_OF and use __maybe_unused
- introduce "phy-handle" ability into ti,cpsw
driver, so I can remove bogus:
if (!of_node && dev->parent->of_node)
of_node = dev->parent->of_node;
construct. Therefore new patch for the ti,cpsw
driver is necessary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add the ability to parse "phy-handle". This
is needed for phys, which have a DT node, and
need to parse DT properties.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a gigabit ethernet PHY is connected to a fast ethernet MAC,
then it can detect 1000 support from the partner but not use it.
This results in a forced speed of 1000 and RX/TX failure.
Check for 1000BASE-T support and then check the advertisement
configuration before setting the MAC speed to 1000mbit.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The register value to enable gpio2 was incorrect. So fix it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This fixes a bug where it is possible for an off-line CPU to fail to go
into a low-power state (nap/sleep/winkle), and to become unresponsive to
requests from the KVM subsystem to wake up and run a VCPU. What can
happen is that a maskable interrupt of some kind (external, decrementer,
hypervisor doorbell, or HMI) after we have called local_irq_disable() at
the beginning of pnv_smp_cpu_kill_self() and before interrupts are
hard-disabled inside power7_nap/sleep/winkle(). In this situation, the
pending event is marked in the irq_happened flag in the PACA. This
pending event prevents power7_nap/sleep/winkle from going to the
requested low-power state; instead they return immediately. We don't
deal with any of these pending event flags in the off-line loop in
pnv_smp_cpu_kill_self() because power7_nap et al. return 0 in this case,
so we will have srr1 == 0, and none of the processing to clear
interrupts or doorbells will be done.
Usually, the most obvious symptom of this is that a KVM guest will fail
with a console message saying "KVM: couldn't grab cpu N".
This fixes the problem by making sure we handle the irq_happened flags
properly. First, we hard-disable before the off-line loop. Once we have
hard-disabled, the irq_happened flags can't change underneath us. We
unconditionally clear the DEC and HMI flags: there is no processing of
timer interrupts while off-line, and the necessary HMI processing is all
done in lower-level code. We leave the EE and DBELL flags alone for the
first iteration of the loop, so that we won't fail to respond to a
split-core request that came in just before hard-disabling. Within the
loop, we handle external interrupts if the EE bit is set in irq_happened
as well as if the low-power state was interrupted by an external
interrupt. (We don't need to do the msgclr for a pending doorbell in
irq_happened, because doorbells are edge-triggered and don't remain
pending in hardware.) Then we clear both the EE and DBELL flags, and
once clear, they cannot be set again (until this CPU comes online again,
that is).
This also fixes the debug check to not be done when we just ran a KVM
guest or when the sleep didn't happen because of a pending event in
irq_happened.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
POWER8"
This reverts commit 9678cdaae939 ("Use the POWER8 Micro Partition
Prefetch Engine in KVM HV on POWER8") because the original commit had
multiple, partly self-cancelling bugs, that could cause occasional
memory corruption.
In fact the logmpp instruction was incorrectly using register r0 as the
source of the buffer address and operation code, and depending on what
was in r0, it would either do nothing or corrupt the 64k page pointed to
by r0.
The logmpp instruction encoding and the operation code definitions could
be corrected, but then there is the problem that there is no clearly
defined way to know when the hardware has finished writing to the
buffer.
The original commit attempted to work around this by aborting the
write-out before starting the prefetch, but this is ineffective in the
case where the virtual core is now executing on a different physical
core from the one where the write-out was initiated.
These problems plus advice from the hardware designers not to use the
function (since the measured performance improvement from using the
feature was actually mostly negative), mean that reverting the code is
the best option.
Fixes: 9678cdaae939 ("Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8")
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
During device assignment/deassignment the flags in the DTE
get lost, which might cause spurious faults, for example
when the device tries to access the system management range.
Fix this by not clearing the flags with the rest of the DTE.
Reported-by: G. Richard Bellamy <rbellamy@pteradigm.com>
Tested-by: G. Richard Bellamy <rbellamy@pteradigm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Suppose that we got a data crc error, and it triggers the mmc_reset.
mmc_reset will call mmc_send_status to see if HW reset was supported.
before issue CMD13, it will do retune, and if EMMC was in HS400 mode,
it will reduce frequency to 52Mhz firstly, then results in card init
was doing at 52Mhz.
The mmc_send_status was originally only done for mmc_test, should drop
it. And, rename the "eMMC hardware reset" to "Reset test", as we would
also be able to use the test for SD-cards.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Current code will always truncate tailing page if its alloc_start is
smaller than inode size.
For example, the file extent layout is like:
0 4K 8K 16K 32K
|<-----Extent A---------------->|
|<--Inode size: 18K---------->|
But if calling fallocate even for range [0,4K), it will cause btrfs to
re-truncate the range [16,32K), causing COW and a new extent.
0 4K 8K 16K 32K
|///////| <- Fallocate call range
|<-----Extent A-------->|<--B-->|
The cause is quite easy, just a careless btrfs_truncate_inode() in a
else branch without extra judgment.
Fix it by add judgment on whether the fallocate range is beyond isize.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
The code in stack tracer should not be executed within an NMI as it grabs
spinlocks and stack tracing an NMI gives the possibility of causing a
deadlock. Although this is safe on x86_64, because it does not perform stack
traces when the task struct stack is not in use (interrupts and NMIs), it
may be an issue for NMIs on i386 and other archs that use the same stack as
the NMI.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
This was introduced with 9e882242c6193ae6f416f2d8d8db0d9126bd996b
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.
Fixes: 9e882242c6 ("block: Add submit_bio_wait(), remove from md")
Cc: stable@vger.kernel.org (v3.10)
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
This was introduced with 9e882242c6193ae6f416f2d8d8db0d9126bd996b
which changed the return value of submit_bio_wait() to return != 0 on
error, but didn't update the caller accordingly.
Fixes: 9e882242c6 ("block: Add submit_bio_wait(), remove from md")
Cc: stable@vger.kernel.org (v3.10)
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
|
|
When discussing the patches to demux ids in rdma_cm instead of ib_cm, it
was decided that it is best to use the P_Key value in the packet headers.
However, the mlx5 and ipath drivers are currently unable to send correct
P_Key values in GMP headers. They always send using a single P_Key that is
set during the GSI QP initialization.
Change the rdma_cm code to look at the P_Key value that is part of the
packet payload as a workaround. Once the drivers are fixed this patch can
be reverted.
Fixes: 4c21b5bcef73 ("IB/cma: Add net_dev and private data checks to
RDMA CM")
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Allocating a workqueue might fail, which wasn't checked so far and would
lead to NULL ptr derefs when an attempt to use it was made.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
If the lookup of a listening ID failed for an AF_IB request, the code
would try to call dev_put() on a NULL net_dev.
Fixes: be688195bd08 ("IB/cma: Fix net_dev reference leak with failed
requests")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When using ifup/ifdown while executing enum_netdev_ipv4_ips,
ifa could become invalid and cause use after free error.
Fixing it by protecting with RCU lock.
Fixes: 03db3a2d81e6 ('IB/core: Add RoCE GID table management')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
clk_add_alias() was not correctly handling the case where alias_dev_name
was NULL: rather than producing an entry with a NULL dev_id pointer,
it would produce a device name of (null). Fix this.
Cc: <stable@vger.kernel.org>
Fixes: 2568999835d7 ("clkdev: add clkdev_create() helper")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We currently do a single update of the vgic state when the distributor
enable/disable control register is accessed and then bypass updating the
state for as long as the distributor remains disabled.
This is incorrect, because updating the state does not consider the
distributor enable bit, and this you can end up in a situation where an
interrupt is marked as pending on the CPU interface, but not pending on
the distributor, which is an impossible state to be in, and triggers a
warning. Consider for example the following sequence of events:
1. An interrupt is marked as pending on the distributor
- the interrupt is also forwarded to the CPU interface
2. The guest turns off the distributor (it's about to do a reboot)
- we stop updating the CPU interface state from now on
3. The guest disables the pending interrupt
- we remove the pending state from the distributor, but don't touch
the CPU interface, see point 2.
Since the distributor disable bit really means that no interrupts should
be forwarded to the CPU interface, we modify the code to keep updating
the internal VGIC state, but always set the CPU interface pending bits
to zero when the distributor is disabled.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
When a guest reboots or offlines/onlines CPUs, it is not uncommon for it
to clear the pending and active states of an interrupt through the
emulated VGIC distributor. However, since the architected timers are
defined by the architecture to be level triggered and the guest
rightfully expects them to be that, but we emulate them as
edge-triggered, we have to mimic level-triggered behavior for an
edge-triggered virtual implementation.
We currently do not signal the VGIC when the map->active field is true,
because it indicates that the guest has already been signalled of the
interrupt as required. Normally this field is set to false when the
guest deactivates the virtual interrupt through the sync path.
We also need to catch the case where the guest deactivates the interrupt
through the emulated distributor, again allowing guests to boot even if
the original virtual timer signal hit before the guest's GIC
initialization sequence is run.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
We have an interesting issue when the guest disables the timer interrupt
on the VGIC, which happens when turning VCPUs off using PSCI, for
example.
The problem is that because the guest disables the virtual interrupt at
the VGIC level, we never inject interrupts to the guest and therefore
never mark the interrupt as active on the physical distributor. The
host also never takes the timer interrupt (we only use the timer device
to trigger a guest exit and everything else is done in software), so the
interrupt does not become active through normal means.
The result is that we keep entering the guest with a programmed timer
that will always fire as soon as we context switch the hardware timer
state and run the guest, preventing forward progress for the VCPU.
Since the active state on the physical distributor is really part of the
timer logic, it is the job of our virtual arch timer driver to manage
this state.
The timer->map->active boolean field indicates whether we have signalled
this interrupt to the vgic and if that interrupt is still pending or
active. As long as that is the case, the hardware doesn't have to
generate physical interrupts and therefore we mark the interrupt as
active on the physical distributor.
We also have to restore the pending state of an interrupt that was
queued to an LR but was retired from the LR for some reason, while
remaining pending in the LR.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The vgic code on ARM is built for all configurations that enable KVM,
but the parent_data field that it references is only present when
CONFIG_IRQ_DOMAIN_HIERARCHY is set:
virt/kvm/arm/vgic.c: In function 'kvm_vgic_map_phys_irq':
virt/kvm/arm/vgic.c:1781:13: error: 'struct irq_data' has no member named 'parent_data'
This flag is implied by the GIC driver, and indeed the VGIC code only
makes sense if a GIC is present. This changes the CONFIG_KVM symbol
to always select GIC, which avoids the issue.
Fixes: 662d9715840 ("arm/arm64: KVM: Kill CONFIG_KVM_ARM_{VGIC,TIMER}")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Jump to correct label and free kvm_host_cpu_state
Reviewed-by: Wei Huang <wei@redhat.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
When lowering a level-triggered line from userspace, we forgot to lower
the pending bit on the emulated CPU interface and we also did not
re-compute the pending_on_cpu bitmap for the CPU affected by the change.
Update vgic_update_irq_pending() to fix the two issues above and also
raise a warning in vgic_quue_irq_to_lr if we encounter an interrupt
pending on a CPU which is neither marked active nor pending.
[ Commit text reworked completely - Christoffer ]
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The stack tracer was triggering the WARN_ON() in module.c:
static void module_assert_mutex_or_preempt(void)
{
#ifdef CONFIG_LOCKDEP
if (unlikely(!debug_locks))
return;
WARN_ON(!rcu_read_lock_sched_held() &&
!lockdep_is_held(&module_mutex));
#endif
}
The reason is that the stack tracer traces all function calls, and some of
those calls happen while exiting or entering user space and idle. Some of
these functions are called after RCU had already stopped watching, as RCU
does not watch userspace or idle CPUs.
If a max stack is hit, then the save_stack_trace() is called, which will
check module addresses and call module_assert_mutex_or_preempt(), and then
trigger the warning. Sad part is, the warning itself will also do a stack
trace and tigger the same warning. That probably should be fixed.
The warning was added by 0be964be0d45 "module: Sanitize RCU usage and
locking" but this bug has probably been around longer. But it's unlikely to
cause much harm, but the new warning causes the system to lock up.
Cc: stable@vger.kernel.org # 4.2+
Cc: Peter Zijlstra <peterz@infradead.org>
Cc:"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
There are 24 EQ registers not 25, I suspect this bug came about because
the registers start at EQ1 not zero. The bug is relatively harmless as
the extra register written is an unused one.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
