| Age | Commit message (Collapse) | Author |
|---|
|
The core_rmw() function calls core_read_mmd_indirect() to read the
requested register, and then calls core_write_mmd_indirect() to write the
requested value to the register. Because Clause 22 is used to access Clause
45 registers, some operations on core_write_mmd_indirect() are
unnecessarily run. Get rid of core_read_mmd_indirect() and
core_write_mmd_indirect(), and run only the necessary operations on
core_write() and core_rmw().
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Read the PHY address the switch listens on from the reg property of the
switch node on the device tree. This change brings support for MT7530
switches on boards with such bootstrapping configuration where the switch
listens on a different PHY address than the hardcoded PHY address on the
driver, 31.
As described on the "MT7621 Programming Guide v0.4" document, the MT7530
switch and its PHYs can be configured to listen on the range of 7-12,
15-20, 23-28, and 31 and 0-4 PHY addresses.
There are operations where the switch PHY registers are used. For the PHY
address of the control PHY, transform the MT753X_CTRL_PHY_ADDR constant
into a macro and use it. The PHY address for the control PHY is 0 when the
switch listens on 31. In any other case, it is one greater than the PHY
address the switch listens on.
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This driver currently doesn't support any control flags.
Use flow_rule_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240418161821.189263-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This driver currently doesn't support any control flags.
Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20240418161802.189247-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This driver currently doesn't support any control flags.
Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Only compile tested, no hardware available.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240418161751.189226-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ensure that the provided netdev name is not one of its aliases to
prevent unnecessary creation and destruction of the vport by
ovs-vswitchd.
Signed-off-by: Jun Gu <jun.gu@easystack.cn>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240419061425.132723-1-jun.gu@easystack.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Donald Hunter says:
====================
netlink: Add nftables spec w/ multi messages
This series adds a ynl spec for nftables and extends ynl with a --multi
command line option that makes it possible to send transactional batches
for nftables.
This series includes a patch for nfnetlink which adds ACK processing for
batch begin/end messages. If you'd prefer that to be sent separately to
nf-next then I can do so, but I included it here so that it gets seen in
context.
An example of usage is:
./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/nftables.yaml \
--multi batch-begin '{"res-id": 10}' \
--multi newtable '{"name": "test", "nfgen-family": 1}' \
--multi newchain '{"name": "chain", "table": "test", "nfgen-family": 1}' \
--multi batch-end '{"res-id": 10}'
[None, None, None, None]
It can also be used for bundling get requests:
./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/nftables.yaml \
--multi gettable '{"name": "test", "nfgen-family": 1}' \
--multi getchain '{"name": "chain", "table": "test", "nfgen-family": 1}' \
--output-json
[{"name": "test", "use": 1, "handle": 1, "flags": [],
"nfgen-family": 1, "version": 0, "res-id": 2},
{"table": "test", "name": "chain", "handle": 1, "use": 0,
"nfgen-family": 1, "version": 0, "res-id": 2}]
There are 2 issues that may be worth resolving:
- ynl reports errors by raising an NlError exception so only the first
error gets reported. This could be changed to add errors to the list
of responses so that multiple errors could be reported.
- If any message does not get a response (e.g. batch-begin w/o patch 2)
then ynl waits indefinitely. A recv timeout could be added which
would allow ynl to terminate.
====================
Link: https://lore.kernel.org/r/20240418104737.77914-1-donald.hunter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The NLM_F_ACK flag is ignored for nfnetlink batch begin and end
messages. This is a problem for ynl which wants to receive an ack for
every message it sends, not just the commands in between the begin/end
messages.
Add processing for ACKs for begin/end messages and provide responses
when requested.
I have checked that iproute2, pyroute2 and systemd are unaffected by
this change since none of them use NLM_F_ACK for batch begin/end.
Signed-off-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240418104737.77914-5-donald.hunter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a "--multi <do-op> <json>" command line to ynl that makes it
possible to add several operations to a single netlink request payload.
The --multi command line option is repeated for each operation.
This is used by the nftables family for transaction batches. For
example:
./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/nftables.yaml \
--multi batch-begin '{"res-id": 10}' \
--multi newtable '{"name": "test", "nfgen-family": 1}' \
--multi newchain '{"name": "chain", "table": "test", "nfgen-family": 1}' \
--multi batch-end '{"res-id": 10}'
[None, None, None, None]
It can also be used for bundling get requests:
./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/nftables.yaml \
--multi gettable '{"name": "test", "nfgen-family": 1}' \
--multi getchain '{"name": "chain", "table": "test", "nfgen-family": 1}' \
--output-json
[{"name": "test", "use": 1, "handle": 1, "flags": [],
"nfgen-family": 1, "version": 0, "res-id": 2},
{"table": "test", "name": "chain", "handle": 1, "use": 0,
"nfgen-family": 1, "version": 0, "res-id": 2}]
Signed-off-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240418104737.77914-4-donald.hunter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NetlinkProtocol.decode() was looking up ops by response value which breaks
when it is used for extack decoding of directional ops. Instead, pass
the op to decode().
Signed-off-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240418104737.77914-3-donald.hunter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a spec for nftables that has nearly complete coverage of the ops,
but limited coverage of rule types and subexpressions.
Signed-off-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240418104737.77914-2-donald.hunter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pavel Begunkov says:
====================
implement io_uring notification (ubuf_info) stacking (net part)
To have per request buffer notifications each zerocopy io_uring send
request allocates a new ubuf_info. However, as an skb can carry only
one uarg, it may force the stack to create many small skbs hurting
performance in many ways.
The patchset implements notification, i.e. an io_uring's ubuf_info
extension, stacking. It attempts to link ubuf_info's into a list,
allowing to have multiple of them per skb.
liburing/examples/send-zerocopy shows up 6 times performance improvement
for TCP with 4KB bytes per send, and levels it with MSG_ZEROCOPY. Without
the patchset it requires much larger sends to utilise all potential.
bytes | before | after (Kqps)
1200 | 195 | 1023
4000 | 193 | 1386
8000 | 154 | 1058
====================
Link: https://lore.kernel.org/all/cover.1713369317.git.asml.silence@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At the moment an skb can only have one ubuf_info associated with it,
which might be a performance problem for zerocopy sends in cases like
TCP via io_uring. Add a callback for assigning ubuf_info to skb, this
way we will implement smarter assignment later like linking ubuf_info
together.
Note, it's an optional callback, which should be compatible with
skb_zcopy_set(), that's because the net stack might potentially decide
to clone an skb and take another reference to ubuf_info whenever it
wishes. Also, a correct implementation should always be able to bind to
an skb without prior ubuf_info, otherwise we could end up in a situation
when the send would not be able to progress.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/all/b7918aadffeb787c84c9e72e34c729dc04f3a45d.1713369317.git.asml.silence@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We'll need to associate additional callbacks with ubuf_info, introduce
a structure holding ubuf_info callbacks. Apart from a more smarter
io_uring notification management introduced in next patches, it can be
used to generalise msg_zerocopy_put_abort() and also store
->sg_from_iter, which is currently passed in struct msghdr.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/all/a62015541de49c0e2a8a0377a1d5d0a5aeb07016.1713369317.git.asml.silence@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric Dumazet says:
====================
tcp: avoid sending too small packets
tcp_sendmsg() cooks 'large' skbs, that are later split
if needed from tcp_write_xmit().
After a split, the leftover skb size is smaller than the optimal
size, and this causes a performance drop.
In this series, tcp_grow_skb() helper is added to shift
payload from the second skb in the write queue to the first
skb to always send optimal sized skbs.
This increases TSO efficiency, and decreases number of ACK
packets.
====================
Link: https://lore.kernel.org/r/20240418214600.1291486-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While investigating TCP performance, I found that TCP would
sometimes send big skbs followed by a single MSS skb,
in a 'locked' pattern.
For instance, BIG TCP is enabled, MSS is set to have 4096 bytes
of payload per segment. gso_max_size is set to 181000.
This means that an optimal TCP packet size should contain
44 * 4096 = 180224 bytes of payload,
However, I was seeing packets sizes interleaved in this pattern:
172032, 8192, 172032, 8192, 172032, 8192, <repeat>
tcp_tso_should_defer() heuristic is defeated, because after a split of
a packet in write queue for whatever reason (this might be a too small
CWND or a small enough pacing_rate),
the leftover packet in the queue is smaller than the optimal size.
It is time to try to make 'leftover packets' bigger so that
tcp_tso_should_defer() can give its full potential.
After this patch, we can see the following output:
14:13:34.009273 IP6 sender > receiver: Flags [P.], seq 4048380:4098360, ack 1, win 256, options [nop,nop,TS val 3425678144 ecr 1561784500], length 49980
14:13:34.010272 IP6 sender > receiver: Flags [P.], seq 4098360:4148340, ack 1, win 256, options [nop,nop,TS val 3425678145 ecr 1561784501], length 49980
14:13:34.011271 IP6 sender > receiver: Flags [P.], seq 4148340:4198320, ack 1, win 256, options [nop,nop,TS val 3425678146 ecr 1561784502], length 49980
14:13:34.012271 IP6 sender > receiver: Flags [P.], seq 4198320:4248300, ack 1, win 256, options [nop,nop,TS val 3425678147 ecr 1561784503], length 49980
14:13:34.013272 IP6 sender > receiver: Flags [P.], seq 4248300:4298280, ack 1, win 256, options [nop,nop,TS val 3425678148 ecr 1561784504], length 49980
14:13:34.014271 IP6 sender > receiver: Flags [P.], seq 4298280:4348260, ack 1, win 256, options [nop,nop,TS val 3425678149 ecr 1561784505], length 49980
14:13:34.015272 IP6 sender > receiver: Flags [P.], seq 4348260:4398240, ack 1, win 256, options [nop,nop,TS val 3425678150 ecr 1561784506], length 49980
14:13:34.016270 IP6 sender > receiver: Flags [P.], seq 4398240:4448220, ack 1, win 256, options [nop,nop,TS val 3425678151 ecr 1561784507], length 49980
14:13:34.017269 IP6 sender > receiver: Flags [P.], seq 4448220:4498200, ack 1, win 256, options [nop,nop,TS val 3425678152 ecr 1561784508], length 49980
14:13:34.018276 IP6 sender > receiver: Flags [P.], seq 4498200:4548180, ack 1, win 256, options [nop,nop,TS val 3425678153 ecr 1561784509], length 49980
14:13:34.019259 IP6 sender > receiver: Flags [P.], seq 4548180:4598160, ack 1, win 256, options [nop,nop,TS val 3425678154 ecr 1561784510], length 49980
With 200 concurrent flows on a 100Gbit NIC, we can see a reduction
of TSO packets (and ACK packets) of about 30 %.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240418214600.1291486-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tcp_write_xmit() calls tcp_init_tso_segs()
to set gso_size and gso_segs on the packet.
tcp_init_tso_segs() requires the stack to maintain
an up to date tcp_skb_pcount(), and this makes sense
for packets in rtx queue. Not so much for packets
still in the write queue.
In the following patch, we don't want to deal with
tcp_skb_pcount() when moving payload from 2nd
skb to 1st skb in the write queue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240418214600.1291486-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tcp_cwnd_test() has a special handing for the last packet in
the write queue if it is smaller than one MSS and has the FIN flag.
This is in violation of TCP RFC, and seems quite dubious.
This packet can be sent only if the current CWND is bigger
than the number of packets in flight.
Making tcp_cwnd_test() result independent of the first skb
in the write queue is needed for the last patch of the series.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240418214600.1291486-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tariq Toukan says:
====================
mlx5e per-queue coalescing
This patchset adds ethtool per-queue coalescing support for the mlx5e
driver.
The series introduce some changes needed as preparations for the final
patch which adds the support and implements the callbacks. Main
changes:
- DIM code movements into its own header file.
- Switch to dynamic allocation of the DIM struct in the RQs/SQs.
- Allow coalescing config change without channels reset when possible.
====================
Link: https://lore.kernel.org/r/20240419080445.417574-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use mlx5 on-the-fly coalescing configuration support to enable individual
channel configuration.
Co-developed-by: Nabil S. Alramli <dev@nalramli.com>
Signed-off-by: Nabil S. Alramli <dev@nalramli.com>
Co-developed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240419080445.417574-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When CQE mode or DIM state is changed, gracefully reconfigure channels to
handle new configuration. Previously, would create new channels that would
reflect the changes rather than update the original channels.
Co-developed-by: Nabil S. Alramli <dev@nalramli.com>
Signed-off-by: Nabil S. Alramli <dev@nalramli.com>
Co-developed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240419080445.417574-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make it possible for the DIM structure to be torn down while an SQ or RQ is
still active. Changing the CQ period mode is an example where the previous
sampling done with the DIM structure would need to be invalidated.
Co-developed-by: Nabil S. Alramli <dev@nalramli.com>
Signed-off-by: Nabil S. Alramli <dev@nalramli.com>
Co-developed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240419080445.417574-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use core DIM CQ period mode enum values for the CQ parameter for the period
mode. Translate the value to the specific mlx5 device constant for the
selected period mode when creating a CQ. Avoid needing to translate mlx5
device constants to DIM constants for core DIM functionality.
Co-developed-by: Nabil S. Alramli <dev@nalramli.com>
Signed-off-by: Nabil S. Alramli <dev@nalramli.com>
Co-developed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240419080445.417574-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Create a header specifically for DIM-related declarations. Move existing
DIM-specific functionality from en.h. Future DIM-related functionality will
be declared in en/dim.h in subsequent patches.
Co-developed-by: Nabil S. Alramli <dev@nalramli.com>
Signed-off-by: Nabil S. Alramli <dev@nalramli.com>
Co-developed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240419080445.417574-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pawel Dembicki says:
====================
net: dsa: vsc73xx: convert to PHYLINK and do some cleanup
This patch series is a result of splitting a larger patch series [0],
where some parts needed to be refactored.
The first patch switches from a poll loop to read_poll_timeout.
The second patch is a simple conversion to phylink because adjust_link
won't work anymore.
The third patch is preparation for future use. Using the
"phy_interface_mode_is_rgmii" macro allows for the proper recognition
of all RGMII modes.
Patches 4-5 involve some cleanup: The fourth patch introduces
a definition with the maximum number of ports to avoid using
magic numbers. The next one fills in documentation.
[0] https://patchwork.kernel.org/project/netdevbpf/list/?series=841034&state=%2A&archive=both
====================
Link: https://lore.kernel.org/r/20240417205048.3542839-1-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This commit adds updates to the documentation describing the structures
used in vsc73xx. This will help prevent kdoc-related issues in the future.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://lore.kernel.org/r/20240417205048.3542839-6-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch introduces a new define: VSC73XX_MAX_NUM_PORTS, which can be
used in the future instead of a hardcoded value.
Currently, the only hardcoded value is vsc->ds->num_ports. It is being
replaced with the new define.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240417205048.3542839-5-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It's preparation for future use. At this moment, the RGMII port is used
only for a connection to the MAC interface, but in the future, someone
could connect a PHY to it. Using the "phy_interface_mode_is_rgmii" macro
allows for the proper recognition of all RGMII modes.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240417205048.3542839-4-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch replaces the adjust_link api with the phylink apis that provide
equivalent functionality.
The remaining functionality from the adjust_link is now covered in the
mac_link_* and mac_config from phylink_mac_ops structure.
Removes:
.adjust_link
Adds phylink_mac_ops structure:
.mac_config
.mac_link_up
.mac_link_down
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://lore.kernel.org/r/20240417205048.3542839-3-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Switch the delay loop during the Arbiter empty check from
vsc73xx_adjust_link() to use read_poll_timeout(). Functionally,
one msleep() call is eliminated at the end of the loop in the timeout
case.
As Russell King suggested:
"This [change] avoids the issue that on the last iteration, the code reads
the register, tests it, finds the condition that's being waiting for is
false, _then_ waits and end up printing the error message - that last
wait is rather useless, and as the arbiter state isn't checked after
waiting, it could be that we had success during the last wait."
Suggested-by: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://lore.kernel.org/r/20240417205048.3542839-2-paweldembicki@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 1eeb50435739 ("tcp/dccp: do not care about
families in inet_twsk_purge()") tcp_twsk_purge() is
no longer potentially called from a module.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support offloading of skbedit mark action.
For example, to mark with 0x0008, with dest ip 60.60.60.2 on eth2
interface:
# tc qdisc add dev eth2 ingress
# tc filter add dev eth2 ingress protocol ip flower \
dst_ip 60.60.60.2 action skbedit mark 0x0008 skip_sw
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an ethX port is disabled in the device tree, an error is returned
by xdp_rxq_info_reg() function while transitioning the CPSW device to
the up state. The message 'Missing net_device from driver' is output.
This patch fixes the issue by registering xdp_rxq info only if ethX
port is enabled (i.e. ndev pointer is not NULL).
Fixes: 8acacc40f733 ("net: ethernet: ti: am65-cpsw: Add minimal XDP support")
Link: https://lore.kernel.org/all/260d258f-87a1-4aac-8883-aab4746b32d8@ti.com/
Reported-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Closes: https://gist.github.com/Siddharth-Vadapalli-at-TI/5ed0e436606001c247a7da664f75edee
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To be able to constify instances of struct ctl_tables it is necessary to
remove ways through which non-const versions are exposed from the
sysctl core.
One of these is the ctl_table_arg member of struct ctl_table_header.
Constify this reference as a prerequisite for the full constification of
struct ctl_table instances.
No functional change.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Westphal says:
====================
testing: make netfilter selftests functional in vng environment
This is the second batch of the netfilter selftest move.
Changes since v1:
- makefile and kernel config are updated to have all required features
- fix makefile with missing bits to make kselftest-install work
- test it via vng as per
https://github.com/linux-netdev/nipa/wiki/How-to-run-netdev-selftests-CI-style
(Thanks Jakub!)
- squash a few fixes, e.g. nft_queue.sh v1 had a race w. NFNETLINK_QUEUE=m
- add a settings file with 8m timeout, for nft_concat_range.sh sake.
That script can be sped up a bit, I think, but its not contained in
this batch yet.
- toss the first two bogus rebase artifacts (Matthieu Baerts)
scripts are moved to lib.sh infra. This allows to use busywait helper
and ditch various 'sleep 2' all over the place.
Tested on Fedora 39:
vng --build --config tools/testing/selftests/net/netfilter/config
make -C tools/testing/selftests/ TARGETS=net/netfilter
vng -v --run . --user root --cpus 2 -- \
make -C tools/testing/selftests TARGETS=net/netfilter run_tests
... all tests pass except nft_audit.sh which SKIPs due to nft version mismatch
(Fedora is on nft 1.0.7 which lacks reset keyword support).
Missing/WIP bits:
- speed up nf_concat_range.sh test
- extend flowtable selftest
- shellcheck fixups for remaining scripts
====================
Link: https://lore.kernel.org/r/20240418152744.15105-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jakub reports the Makefile missed a few updates to make kselftest-install
work for the netfilter tests and points out that config file lacks many
dependencies such as VETH support.
The settings file (timeout 8m) is added for nft_concat_range.sh script
which can take several minutes to complete.
Fixes: 3f189349e52a ("selftests: netfilter: move to net subdir")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/all/20240412175413.04e5e616@kernel.org/
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-13-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This testcase doesn't work if auditd is running, audit_logread will not
receive any data in that case.
Add a nftables feature test for the reset keyword and skip this test
if that fails.
While at it, do a few minor shellcheck cleanups.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-12-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
shellcheck complains about missing "", so add those.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-11-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
no functional change intended.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-10-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No functional change intended.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-9-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While at it: No need for iperf here, use socat.
This also reduces the script runtime.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-8-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
no functional change intended.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-7-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Intentional changes:
- Use socat instead of netcat
- Use a temporary file instead of pipe, else packets do not match
"-m string" rules, multiple writes to the pipe cause multiple packets,
but this needs only one to work.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-6-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Also do shellcheck cleanups here, no functional changes intended.
When running tests via vng tool, the packetpath insertion test fails:
dd: failed to open '/dev/stdout': Device or resource busy
Just omit 'of=' and this will work as intended.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-5-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
use checktool helper where applicable.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-4-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No functional change intended. Disable frequent shellcheck warnings wrt.
"unreachable" code, those helpers get called indirectly from busywait helper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-3-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
- switch to socat, like other tests
- use buswait helper to test once listener netns is ready
- do not generate multiple input test files, only generate
one and use cleanup hook to remove it, like other temporary files.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240418152744.15105-2-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric Dumazet says:
====================
neighbour: convert neigh_dump_info() to RCU
Remove RTNL requirement for "ip neighbour show" command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
neigh_dump_table() is already relying on RCU protection.
pneigh_dump_table() is using its own protection (tbl->lock)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change neigh_dump_table() and pneigh_dump_table()
to either return 0 or -EMSGSIZE if not enough
space was available in the skb.
Then neigh_dump_info() can do the same.
This allows NLMSG_DONE to be appended to the current
skb at the end of a dump, saving a couple of recvmsg()
system calls.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
