| Age | Commit message (Collapse) | Author |
|---|
|
Notify users when TX vlan offload feature changed with ethtool.
Relevant command - ethtool -K <eth> txvlan on/off.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch improves memory utilization and therefore the packets rate
for special MTU's. Instead of setting the frag_stride to the maximal
hard coded frag_size, use the actual frag_size that is set according to
the MTU, when setting the stride of the last frag.
So, for example, for MTU 1600, where the frag_size of the 2nd frag is
86, the frag_size is set to 128 instead of 4096. See below:
Before:
frag:0 - size:1536 prefix:0 stride:1536
frag:1 - size:86 prefix:1536 stride:4096
frag 0 allocator: - size:32768 frags:21
frag 1 allocator: - size:32768 frags:8
After:
frag:0 - size:1536 prefix:0 stride:1536
frag:1 - size:86 prefix:1536 stride:128
frag 0 allocator: - size:32768 frags:21
frag 1 allocator: - size:32768 frags:256
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After Initialization of page_alloc, print actual allocated page
size and number of frags it contains. prints is done only when drv
message level is set on the interface.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Align the IDs in the code with the modinfo, lspci -n, etc tools outputs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We do support cache line sizes of 32 and 64 bytes without activating the
CQE stride feature. Fix a misleading print saying that these cache line
sizes aren't supported.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
using
Add Initialization to struct config_dev before filling and using it.
Fix to warning:
warning: config_dev.rx_checksum_val may be used uninitialized in this function
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
a) Previously, mlx4_mr_rereg_write filled the MPT's start
and length with the old MPT's values.
Fixing the initialization to take the new start and length.
b) In addition access flags in mpt_status were initialized instead of
status due to bad boolean operation. Fixing the operation.
c) Initialization of pd_slave caused a protection error.
Fix - removing this initialization.
d) In resource_tracker.c: Fixing vf encoding to be one-based.
Fixes: e630664c ('mlx4_core: Add helper functions to support MR re-registration')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Or Gerlitz says:
====================
Add HA and LAG support to mlx4 RoCE and SRIOV services
This series takes advanges of bonding mlx4 Ethernet devices to support
a model of High-Availability and Link Aggregation for more environments.
The mlx4 driver reacts on netdev events generated by bonding when
slave state changes happen by programming a HW V2P (Virt-to-Phys)
port table. Bonding was extended to expose these state changes
through netdev events.
When an mlx4 interface such as the mlx4 IB/RoCE driver is subject to
this policy, QPs are created over virtual ports which are mapped
to one of the two physical ports. When a failure happens, the
re-programming of the V2P table allows traffic to keep flowing.
The mlx4 Ethernet driver interfaces are not subject to this
policy and act as usual.
A 2nd use-case for this model would be to add HA and Link Aggregation
support to single ported mlx4 Ethernet VFs. In this case, the PF Ethernet
intrfaces are bonded, all the VFs see single port devices (which is
supported already today), and VF QPs are subject to V2P.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the mlx4 IB (RoCE) device works in link aggregation mode, it
exposes a single port to upper layers. Therefore, applications always
set '1' in port_num attribute when modifying a QP or creating an address handle.
To make sure that a node uses all available ports the mlx4 driver will
override the port_num attribute with a round robin policy.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In port aggregation mode flows for port #1 (the only port) should be mirrored
on port #2. This is because packets can arrive from either physical ports.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register the interface with the mlx4 core driver with port aggregation support
and check for port aggregation mode when the 'add' function is called.
In this mode, only one physical port is reported to the upper layer
(RoCE/IB core stack and ULPs).
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is implemented twice... get rid of one copy.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Capture NETDEV events generated by the bonding driver and based on that
make decisions of how to configure port aggregation in the mlx4 core driver.
This includes setting the V2P port table and re-creating the interested
interfaces in bonded/non-bonded mode.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Supply interface functions to bond and unbond ports of a mlx4 internal
interfaces. Example for such an interface is the one registered by the
mlx4 IB driver under RoCE.
There are
1. Functions to go in/out to/from bonded mode
2. Function to remap virtual ports to physical ports
The bond_mutex prevents simultaneous access to data that keep status of
the device in bonded mode.
The upper mlx4 interface marks to the mlx4 core module that they
want to be subject for such bonding by setting the MLX4_INTFF_BONDING
flag. Interface which goes to/from bonded mode is re-created.
The mlx4 Ethernet driver does not set this flag when registering the
interface, the IB driver does.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the hardware interface required for port aggregation.
1. Disable RX port check on receive - don't perform a validity check
that matches to QP's port and the port where the packet is received.
2. Virtual to physical port remap - configure virtual to physical port
mapping. Port remap capability for virtual functions.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use notifier chain to dispatch an event upon a change in slave state.
Event is dispatched with slave specific info.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move slave state changes to a helper function, this is a pre-step for adding
functionality of dispatching an event when this helper is called.
This commit doesn't add new functionality.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add event which provides an indication on a change in the state
of a bonding slave. The event handler should cast the pointer to the
appropriate type (struct netdev_bonding_info) in order to get the
full info about the slave.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jon Maloy says:
====================
tipc: some small fixes
During extensive testing and analysis of running dual links between
nodes, we have encountered some issues that potentially may cause
problems. We choose to fix those proactively in this series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a new link instance is created, it is trigged to start by
sending it a TIPC_STARTING_EVT, whereafter a regular link
reset is applied to it.
The starting event is codewise treated as a timeout event, and prompts
a link RESET message to be sent to the peer node, carrying a link
session identifier. The later link_reset() call nudges this session
identifier, whereafter all subsequent RESET messages will be sent out
with the new identifier. The latter session number overrides the former,
causing the peer to unconditionally accept it irrespective of its
current working state.
We don't think that this causes any problem, but it is not in accordance
with the protocol spec, and may cause confusion when debugging TIPC
sessions.
To avoid this, we make the starting event distinct from the
subsequent timeout events, by not allowing the former to send
out any RESET message. This eliminates the described problem.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instances of struct node are created in the function tipc_disc_rcv()
under the assumption that there is no race between received discovery
messages arriving from the same node. This assumption is wrong.
When we use more than one bearer, it is possible that discovery
messages from the same node arrive at the same moment, resulting in
creation of two instances of struct tipc_node. This may later cause
confusion during link establishment, and may result in one of the links
never becoming activated.
We fix this by making lookup and potential creation of nodes atomic.
Instead of first looking up the node, and in case of failure, create it,
we now start with looking up the node inside node_link_create(), and
return a reference to that one if found. Otherwise, we go ahead and
create the node as we did before.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During link failover it may happen that the remaining link goes
down while it is still in the process of taking over traffic
from a previously failed link. When this happens, we currently
abort the failover procedure and reset the first failed link to
non-failover mode, so that it will be ready to re-establish
contact with its peer when it comes available.
However, if the first link goes down because its bearer was manually
disabled, it is not enough to reset it; it must also be deleted;
which is supposed to happen when the failover procedure is finished.
Otherwise it will remain a zombie link: attached to the owner node
structure, in mode LINK_STOPPED, and permanently blocking any re-
establishing of the link to the peer via the interface in question.
We fix this by amending the failover abort procedure. Apart from
resetting the link to non-failover state, we test if the link is
also in LINK_STOPPED mode. If so, we delete it, using the conditional
tipc_link_delete() function introduced in the previous commit.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a bearer is disabled, all pertaining links will be reset and
deleted. However, if there is a second active link towards a killed
link's destination, the delete has to be postponed until the failover
is finished. During this interval, we currently put the link in zombie
mode, i.e., we take it out of traffic, delete its timer, but leave it
attached to the owner node structure until all missing packets have
been received. When this is done, we detach the link from its node
and delete it, assuming that the synchronous timer deletion that was
initiated earlier in a different thread has finished.
This is unsafe, as the failover may finish before del_timer_sync()
has returned in the other thread.
We fix this by adding an atomic reference counter of type kref in
struct tipc_link. The counter keeps track of the references kept
to the link by the owner node and the timer. We then do a conditional
delete, based on the reference counter, both after the failover has
been finished and when the timer expires, if applicable. Whoever
comes last, will actually delete the link. This approach also implies
that we can make the deletion of the timer asynchronous.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Max unacked packets/bytes is an int while sizeof(long) was used in the
sysctl table.
This means that when they were getting read we'd also leak kernel memory
to userspace along with the timeout values.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Last round of updates for net-next:
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to use firmware version macros from t4fw_version.h
and also enables 40g T5 adapter.
Signed-off-by: Praveen Madhavan <praveenm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In virtio 1.0 mode, when mergeable buffers are enabled on a big-endian
host, num_buffers wasn't byte-swapped correctly, so large incoming
packets got corrupted.
To fix, fill it in within hdr - this also makes sure it gets
the correct type.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
As there is a discrepancy between the code and the comments this is in
a separate patch.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-02-03
Here's what's likely the last bluetooth-next pull request for 3.20.
Notable changes include:
- xHCI workaround + a new id for the ath3k driver
- Several new ids for the btusb driver
- Support for new Intel Bluetooth controllers
- Minor cleanups to ieee802154 code
- Nested sleep warning fix in socket accept() code path
- Fixes for Out of Band pairing handling
- Support for LE scan restarting for HCI_QUIRK_STRICT_DUPLICATE_FILTER
- Improvements to data we expose through debugfs
- Proper handling of Hardware Error HCI events
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch correct the bad expression while writing the
bit-pattern from software's buffer to hardware registers.
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds skb_remcsum_process and skb_gro_remcsum_process to
perform the appropriate adjustments to the skb when receiving
remote checksum offload.
Updated vxlan and gue to use these functions.
Tested: Ran TCP_RR and TCP_STREAM netperf for VXLAN and GUE, did
not see any change in performance.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commone register macors (e.g. RSR) is too commont to drivers, it may
be conflict with the architectures (e.g. xtensa, sh).
The related warnings (with allmodconfig under xtensa):
CC [M] drivers/net/usb/sr9700.o
In file included from drivers/net/usb/sr9700.c:24:0:
drivers/net/usb/sr9700.h:65:0: warning: "RSR" redefined
#define RSR 0x06
^
In file included from ./arch/xtensa/include/asm/bitops.h:22:0,
from include/linux/bitops.h:36,
from include/linux/kernel.h:10,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/net/usb/sr9700.c:13:
./arch/xtensa/include/asm/processor.h:190:0: note: this is the location of the previous definition
#define RSR(v,sr) __asm__ __volatile__ ("rsr %0,"__stringify(sr) : "=a"(v));
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when 'external' entity notifies the aging
When 'learned_sync' flag is turned on, the offloaded switch
port syncs learned MAC addresses to bridge's FDB via switchdev notifier
(NETDEV_SWITCH_FDB_ADD). Currently, FDB entries learnt via this mechanism are
wrongly being deleted by bridge aging logic. This patch ensures that FDB
entries synced from offloaded switch ports are not deleted by bridging logic.
Such entries can only be deleted via switchdev notifier
(NETDEV_SWITCH_FDB_DEL).
Signed-off-by: Siva Mannem <siva.mannem.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Freescale ethernet controllers have the capability to re-assemble fragmented
data into a single ethernet frame. This patch uses this capability and
implements NETIP_F_SG feature into the fs_enet ethernet driver.
On a MPC885, I get 53% performance improvement on a ftp transfer of a 15Mb file:
* Without the patch : 2,8 Mbps
* With the patch : 4,3 Mbps
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A typical qdisc setup is the following :
bond0 : bonding device, using HTB hierarchy
eth1/eth2 : slaves, multiqueue NIC, using MQ + FQ qdisc
XPS allows to spread packets on specific tx queues, based on the cpu
doing the send.
Problem is that dequeues from bond0 qdisc can happen on random cpus,
due to the fact that qdisc_run() can dequeue a batch of packets.
CPUA -> queue packet P1 on bond0 qdisc, P1->ooo_okay=1
CPUA -> queue packet P2 on bond0 qdisc, P2->ooo_okay=0
CPUB -> dequeue packet P1 from bond0
enqueue packet on eth1/eth2
CPUC -> dequeue packet P2 from bond0
enqueue packet on eth1/eth2 using sk cache (ooo_okay is 0)
get_xps_queue() then might select wrong queue for P1, since current cpu
might be different than CPUA.
P2 might be sent on the old queue (stored in sk->sk_tx_queue_mapping),
if CPUC runs a bit faster (or CPUB spins a bit on qdisc lock)
Effect of this bug is TCP reorders, and more generally not optimal
TX queue placement. (A victim bulk flow can be migrated to the wrong TX
queue for a while)
To fix this, we have to record sender cpu number the first time
dev_queue_xmit() is called for one tx skb.
We can union napi_id (used on receive path) and sender_cpu,
granted we clear sender_cpu in skb_scrub_packet() (credit to Willem for
this union idea)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
spi-linus
|
|
Pull cifs fixes from Steve French:
"Three small cifs fixes. One fixes a hang under stress, and the other
two are security related"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix MUST SecurityFlags filtering
Complete oplock break jobs before closing file handle
cifs: use memzero_explicit to clear stack buffer
|
|
Pull ARM fixes from Russell King:
"A number of ARM fixes, the biggest is fixing a regression caused by
appended DT blobs exceeding 64K, causing the decompressor fixup code
to fail to patch the DT blob. Another important fix is for the ASID
allocator from Will Deacon which prevents some rare crashes seen on
some systems. Lastly, there's a build fix for v7M systems when printk
support is disabled.
The last two remaining fixes are more cosmetic - the IOMMU one
prevents an annoying harmless warning message, and we disable the
kernel strict memory permissions on non-MMU which can't support it
anyway"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8299/1: mm: ensure local active ASID is marked as allocated on rollover
ARM: 8298/1: ARM_KERNMEM_PERMS only works with MMU enabled
ARM: 8295/1: fix v7M build for !CONFIG_PRINTK
ARM: 8294/1: ATAG_DTB_COMPAT: remove the DT workspace's hardcoded 64KB size
ARM: 8288/1: dma-mapping: don't detach devices without an IOMMU during teardown
|
|
Sending data in high speed then introducing a busoff results
in spurious BUS_ERROR events from the USBCan-II firmware directly
_after_ the triggered BUS_OFF event.
In the current CAN state handling code, this will lead to an
invalid can state of ACTIVE, ERROR, or PASSIVE even though the
CAN controller has been already shut down due to the busoff.
Guard the state handling code from such invalid events.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
return type of wait_for_completion_timeout is unsigned long not int, this patch
removes the type mismatch by moving the call into the condition.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Vladislav Yasevich says:
====================
Restore UFO support to virtio_net devices
commit 3d0ad09412ffe00c9afa201d01effdb6023d09b4
Author: Ben Hutchings <ben@decadent.org.uk>
Date: Thu Oct 30 18:27:12 2014 +0000
drivers/net: Disable UFO through virtio
Turned off UFO support to virtio-net based devices due to issues
with IPv6 fragment id generation for UFO packets. The issue
was that IPv6 UFO/GSO implementation expects the fragment id
to be supplied in skb_shinfo(). However, for packets generated
by the VMs, the fragment id is not supplied which causes all
IPv6 fragments to have the id of 0.
The problem is that turning off UFO support on tap/macvtap
as well as virtio devices caused issues with migrations.
Migrations would fail when moving a vm from a kernel supporting
expecting UFO to work to the newer kernels that disabled UFO.
This series provides a partial solution to address the migration
issue. The series allows us to track whether skb_shinfo()->ip6_frag_id
has been set by treating value of 0 as unset.
This lets GSO code to generate fragment ids if they are necessary
(ex: packet was generated by VM or packet socket).
Since v3:
- Resolved build issue when IPv6 is a module.
- Removed trailing white space.
Since v2:
- Rebase and rebuild to make sure everything works. No changes
to the patches were done.
Since v1:
- Removed the skb bit and use value of 0 as tracker.
- Used Eric's suggestion to set fragment id as 0x80000000 if id
generation procedure yeilded a 0 result.
- Consolidated ipv6 id genration code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 3d0ad09412ffe00c9afa201d01effdb6023d09b4.
Now that GSO functionality can correctly track if the fragment
id has been selected and select a fragment id if necessary,
we can re-enable UFO on tap/macvap and virtio devices.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 5188cd44c55db3e92cd9e77a40b5baa7ed4340f7.
Now that GSO layer can track if fragment id has been selected
and can allocate one if necessary, we don't need to do this in
tap and macvtap. This reverts most of the code and only keeps
the new ipv6 fragment id generation function that is still needed.
Fixes: 3d0ad09412ff (drivers/net: Disable UFO through virtio)
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the IPv6 fragment id has not been set and we perform
fragmentation due to UFO, select a new fragment id.
We now consider a fragment id of 0 as unset and if id selection
process returns 0 (after all the pertrubations), we set it to
0x80000000, thus giving us ample space not to create collisions
with the next packet we may have to fragment.
When doing UFO integrity checking, we also select the
fragment id if it has not be set yet. This is stored into
the skb_shinfo() thus allowing UFO to function correclty.
This patch also removes duplicate fragment id generation code
and moves ipv6_select_ident() into the header as it may be
used during GSO.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
it has just verified that it asks no more than the length of the
first segment of iovec.
And with that the last user of stuff in lib/iovec.c is gone.
RIP.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Nicholas A. Bellinger <nab@linux-iscsi.org>
Cc: kvm@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: kvm@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
just advance the msg.msg_iter and be done with that.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: kvm@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: kvm@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
