| Age | Commit message (Collapse) | Author |
|---|
|
Referenced commit prepared the code for upcoming extension that allows mlx5
to offload police action attached to flower classifier. However, with
regard to existing matchall classifier offload validation should be
reversed as FLOW_ACTION_CONTINUE is the only supported notexceed police
action type. Fix the problem by allowing FLOW_ACTION_CONTINUE for police
action and extend scan_tc_matchall_fdb_actions() to only allow such actions
with matchall classifier.
Fixes: d97b4b105ce7 ("flow_offload: reject offload for all drivers with invalid police parameters")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Offloading police with action TC_ACT_UNSPEC was erroneously disabled even
though it was supported by mlx5 matchall offload implementation, which
didn't verify the action type but instead assumed that any single police
action attached to matchall classifier is a 'continue' action. Lack of
action type check made it non-obvious what mlx5 matchall implementation
actually supports and caused implementers and reviewers of referenced
commits to disallow it as a part of improved validation code.
Fixes: b8cd5831c61c ("net: flow_offload: add tc police action parameters")
Fixes: b50e462bc22d ("net/sched: act_police: Add extack messages for offload failure")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ratheesh Kannoth says:
====================
octeontx2: *** Exact Match Table and Field hash ***
*** Exact match table and Field hash support for CN10KB silicon ***
Ratheesh Kannoth (11):
These patch series enables exact match table in CN10KB silicon. Legacy
silicon used NPC mcam to do packet fields/channel matching for NPC rules.
NPC mcam resources exahausted as customer use case increased.
Supporting many DMAC filter becomes a challenge, as RPM based filter
count is less. Exact match table has 4way 2K entry table and a 32 entry
fully associative cam table. Second table is to handle hash
table collision overflows in 4way 2K entry table. Enabling exact match table
results in KEX key to be appended with Hit/Miss status. This can be used
to match in NPC mcam for a more generic rule and drop those packets than
having DMAC drop rules for each DMAC entry in NPC mcam.
octeontx2-af: Exact match support
octeontx2-af: Exact match scan from kex profile
octeontx2-af: devlink configuration support
octeontx2-af: FLR handler for exact match table.
octeontx2-af: Drop rules for NPC MCAM
octeontx2-af: Debugsfs support for exact match.
octeontx2: Modify mbox request and response structures
octeontx2-af: Wrapper functions for mac addr add/del/update/reset
octeontx2-af: Invoke exact match functions if supported
octeontx2-pf: Add support for exact match table.
octeontx2-af: Enable Exact match flag in kex profile
Suman Ghosh (1):
CN10KB variant of CN10K series of silicons supports
a new feature where in a large protocol field
(eg 128bit IPv6 DIP) can be condensed into a small
hashed 32bit data. This saves a lot of space in MCAM key
and allows user to add more protocol fields into the filter.
A max of two such protocol data can be hashed.
This patch adds support for hashing IPv6 SIP and/or DIP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enabled EXACT match flag in Kex default profile. Since
there is no space in key, NPC_PARSE_NIBBLE_ERRCODE
is removed
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NPC exact match table can support more entries than RPM
dmac filters. This requires field size of DMAC filter count
and index to be increased.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If exact match table is suppoted, call functions to add/del/update
entries in exact match table instead of RPM dmac filters
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These functions are wrappers for mac add/addr/del/update in
exact match table. These will be invoked from mbox handler routines
if exact matct table is supported and enabled.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Exact match table modification requires wider fields as it has
more number of slots to fill in. Modifying an entry in exact match
table may cause hash collision and may be required to delete entry
from 4-way 2K table and add to fully associative 32 entry CAM table.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There debugfs files created.
1. General information on exact match table
2. Exact match table entries.
3. NPC mcam drop on hit count stats.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NPC exact match table installs drop on hit rules in
NPC mcam for each channel. This rule has broadcast and multicast
bits cleared. Exact match bit cleared and channel bits
set. If exact match table hit bit is 0, corresponding NPC mcam
drop rule will be hit for the packet and will be dropped.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FLR handler should remove/free all exact match table resources
corresponding to each interface.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CN10KB silicon supports Exact match feature. This feature can be disabled
through devlink configuration. Devlink command fails if DMAC filter rules
are already present. Once disabled, legacy RPM based DMAC filters will be
configured.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CN10KB silicon supports exact match table. Scanning KEX
profile should check for exact match feature is enabled
and then set profile masks properly.
These kex profile masks are required to configure NPC
MCAM drop rules. If there is a miss in exact match table,
these drop rules will drop those packets.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CN10KB silicon has support for exact match table. This table
can be used to match maimum 64 bit value of KPU parsed output.
Hit/non hit in exact match table can be used as a KEX key to
NPC mcam.
This patch makes use of Exact match table to increase number of
DMAC filters supported. NPC mcam is no more need for each of these
DMAC entries as will be populated in Exact match table.
This patch implements following
1. Initialization of exact match table only for CN10KB.
2. Add/del/update interface function for exact match table.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CN10KB variant of CN10K series of silicons supports
a new feature where in a large protocol field
(eg 128bit IPv6 DIP) can be condensed into a small
hashed 32bit data. This saves a lot of space in MCAM key
and allows user to add more protocol fields into the filter.
A max of two such protocol data can be hashed.
This patch adds support for hashing IPv6 SIP and/or DIP.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge branch 'nfp-tso'
Simon Horman says:
====================
nfp: enable TSO by default
this short series enables TSO by default on all NICs supported by the NFP
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can benefit from TSO when the host CPU is not powerful enough,
so enable it by default now.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets with metadata prepended can be correctly handled in
firmware when TSO is enabled, now remove the error path and
related comments. Since there's no existing firmware that
uses prepended metadata, no need to add compatibility check
here.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The functions of asix_set_sw/hw_mii are not called in other files, so
change them to static.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220704123448.128980-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Instead of counting the child nodes in the device tree, hardcode the
number of ports in the driver itself. The counting won't work at all
if an ethernet port is marked as disabled, e.g. because it is not
connected on the board at all.
It turns out that the LAN9662 and LAN9668 use the same switching IP
with the same synthesis parameters. The only difference is that the
output ports are not connected. Thus, we can just hardcode the
number of physical ports to 8.
Fixes: db8bcaad5393 ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220704153654.1167886-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
felix_vsc9959.c calls taprio_offload_get() and taprio_offload_free(),
symbols exported by net/sched/sch_taprio.c. As such, we must disallow
building the Felix driver as built-in when the symbol exported by
tc-taprio isn't present in the kernel image.
Fixes: 1c9017e44af2 ("net: dsa: felix: keep reference on entire tc-taprio config")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220704190241.1288847-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All callers of taprio_offload_get() and taprio_offload_free() prior to
the blamed commit are conditionally compiled based on CONFIG_NET_SCH_TAPRIO.
felix_vsc9959.c is different; it provides vsc9959_qos_port_tas_set()
even when taprio is compiled out.
Provide shim definitions for the functions exported by taprio so that
felix_vsc9959.c is able to compile. vsc9959_qos_port_tas_set() in that
case is dead code anyway, and ocelot_port->taprio remains NULL, which is
fine for the rest of the logic.
Fixes: 1c9017e44af2 ("net: dsa: felix: keep reference on entire tc-taprio config")
Reported-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Link: https://lore.kernel.org/r/20220704190241.1288847-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The last meaningful change to this driver was made by Jon in 2011.
As much as we'd like to believe that this is because the code is
perfect the chances are nobody is using this hardware.
Because of the size of this driver there is a nontrivial maintenance
cost to keeping this code around, in the last 2 years we're averaging
more than 1 change a month. Some of which require nontrivial review
effort, see commit 877fe9d49b74 ("Revert "drivers/net/ethernet/neterion/vxge:
Fix a use-after-free bug in vxge-main.c"") for example.
Let's try to remove this driver. In general, IMHO, we need to
establish a clear path for shedding dead code. It will be hard
to unless we have some experience trying to delete stuff.
Link: https://lore.kernel.org/r/20220701044234.706229-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 'reg' property is missing from the mediatek,mt7530 schema which
results in the following warning once 'unevaluatedProperties' is fixed:
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.example.dtb: switch@0: Unevaluated properties are not allowed ('reg' was unexpected)
Fixes: e0dda3119741 ("dt-bindings: net: dsa: convert binding for mediatek switches")
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220701222240.1706272-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fix deadlock when powering on.
* tag 'for-net-2022-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: core: Fix deadlock on hci_power_on_sync.
====================
Link: https://lore.kernel.org/r/20220705202700.1689796-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
`cancel_work_sync(&hdev->power_on)` was moved to hci_dev_close_sync in
commit [1] to ensure that power_on work is canceled after HCI interface
down.
But, in certain cases power_on work function may call hci_dev_close_sync
itself: hci_power_on -> hci_dev_do_close -> hci_dev_close_sync ->
cancel_work_sync(&hdev->power_on), causing deadlock. In particular, this
happens when device is rfkilled on boot. To avoid deadlock, move
power_on work canceling out of hci_dev_do_close/hci_dev_close_sync.
Deadlock introduced by commit [1] was reported in [2,3] as broken
suspend. Suspend did not work because `hdev->req_lock` held as result of
`power_on` work deadlock. In fact, other BT features were not working.
It was not observed when testing [1] since it was verified without
rfkill in place.
NOTE: It is not needed to cancel power_on work from other places where
hci_dev_do_close/hci_dev_close_sync is called in case:
* Requests were serialized due to `hdev->req_workqueue`. The power_on
work is first in that workqueue.
* hci_rfkill_set_block which won't close device anyway until HCI_SETUP
is on.
* hci_sock_release which runs after hci_sock_bind which ensures
HCI_SETUP was cleared.
As result, behaviour is the same as in pre-dd06ed7 commit, except
power_on work cancel added to hci_dev_close.
[1]: commit ff7f2926114d ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
[2]: https://lore.kernel.org/lkml/20220614181706.26513-1-max.oss.09@gmail.com/
[2]: https://lore.kernel.org/lkml/1236061d-95dd-c3ad-a38f-2dae7aae51ef@o2.pl/
Fixes: ff7f2926114d ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com>
Reported-by: Max Krummenacher <max.krummenacher@toradex.com>
Reported-by: Mateusz Jonczyk <mat.jonczyk@o2.pl>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen security fixes from Juergen Gross:
- XSA-403 (4 patches for blkfront and netfront drivers):
Linux Block and Network PV device frontends don't zero memory regions
before sharing them with the backend (CVE-2022-26365,
CVE-2022-33740). Additionally the granularity of the grant table
doesn't allow sharing less than a 4K page, leading to unrelated data
residing in the same 4K page as data shared with a backend being
accessible by such backend (CVE-2022-33741, CVE-2022-33742).
- XSA-405 (1 patch for netfront driver, only 5.10 and newer):
While adding logic to support XDP (eXpress Data Path), a code label
was moved in a way allowing for SKBs having references (pointers)
retained for further processing to nevertheless be freed.
- XSA-406 (1 patch for Arm specific dom0 code):
When mapping pages of guests on Arm, dom0 is using an rbtree to keep
track of the foreign mappings.
Updating of that rbtree is not always done completely with the
related lock held, resulting in a small race window, which can be
used by unprivileged guests via PV devices to cause inconsistencies
of the rbtree. These inconsistencies can lead to Denial of Service
(DoS) of dom0, e.g. by causing crashes or the inability to perform
further mappings of other guests' memory pages.
* tag 'xsa-5.19-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/arm: Fix race in RB-tree based P2M accounting
xen-netfront: restore __skb_queue_tail() positioning in xennet_get_responses()
xen/blkfront: force data bouncing when backend is untrusted
xen/netfront: force data bouncing when backend is untrusted
xen/netfront: fix leaking data in shared pages
xen/blkfront: fix leaking data in shared pages
|
|
The previous cleanup with devres may lead to the incorrect release
orders at the probe error handling due to the devres's nature. Until
we register the card, snd_card_free() has to be called at first for
releasing the stuff properly when the driver tries to manage and
release the stuff via card->private_free().
This patch fixes it by calling snd_card_free() manually on the error
from the probe callback.
Fixes: 5bff69b3645d ("ALSA: cs46xx: Allocate resources with device-managed APIs")
Cc: <stable@vger.kernel.org>
Reported-and-tested-by: Jan Engelhardt <jengelh@inai.de>
Link: https://lore.kernel.org/r/p2p1s96o-746-74p4-s95-61qo1p7782pn@vanv.qr
Link: https://lore.kernel.org/r/20220705152336.350-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use bitmap_zalloc()/bitmap_free() instead of hand-writing them.
It is less verbose and it improves the semantic.
While at it, remove a useless bitmap_zero(). The bitmap is already zeroed
when allocated.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/8a2168ef9871bd9c4f1cf19b8d5f7530662a5d15.1656866770.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We can't use the division operator on 64 bits integers, that breaks
32 bits build. Instead use the relevant helper.
Fixes: 6ddac26cf763 ("net/mlx5e: Add support to modify hardware flow meter parameters")
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/ecb00ddd1197b4f8a4882090206bd2eee1eb8b5b.1657005206.git.pabeni@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
'fix-bridge_vlan_aware-sh-and-bridge_vlan_unaware-sh-with-iff_unicast_flt'
Vladimir Oltean says:
====================
Fix bridge_vlan_aware.sh and bridge_vlan_unaware.sh with IFF_UNICAST_FLT
Make sure that h1 and h2 don't drop packets with a random MAC DA, which
otherwise confuses these selftests. Also, fix an incorrect error message
found during those failures.
====================
Link: https://lore.kernel.org/r/20220703073626.937785-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When packets are not received, they aren't received on $host1_if, so the
message talking about the second host not receiving them is incorrect.
Fix it.
Fixes: d4deb01467ec ("selftests: forwarding: Add a test for FDB learning")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The first host interface has by default no interest in receiving packets
MAC DA de:ad:be:ef:13:37, so it might drop them before they hit the tc
filter and this might confuse the selftest.
Enable promiscuous mode such that the filter properly counts received
packets.
Fixes: d4deb01467ec ("selftests: forwarding: Add a test for FDB learning")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As mentioned in the blamed commit, flood_unicast_test() works by
checking the match count on a tc filter placed on the receiving
interface.
But the second host interface (host2_if) has no interest in receiving a
packet with MAC DA de:ad:be:ef:13:37, so its RX filter drops it even
before the ingress tc filter gets to be executed. So we will incorrectly
get the message "Packet was not flooded when should", when in fact, the
packet was flooded as expected but dropped due to an unrelated reason,
at some other layer on the receiving side.
Force h2 to accept this packet by temporarily placing it in promiscuous
mode. Alternatively we could either deliver to its MAC address or use
tcpdump_start, but this has the fewest complications.
This fixes the "flooding" test from bridge_vlan_aware.sh and
bridge_vlan_unaware.sh, which calls flood_test from the lib.
Fixes: 236dd50bf67a ("selftests: forwarding: Add a test for flooded traffic")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Kuniyuki Iwashima says:
====================
af_unix: Fix regression by the per-netns hash table series.
The series 6dd4142fb5a9 ("Merge branch 'af_unix-per-netns-socket-hash'")
replaced a global hash table with per-netns tables, which caused regression
reported in the links below. [0][1]
When a pathname socket is visible, any socket with the same type has to be
able to connect to it even in different netns. The series puts all sockets
into each namespace's hash table, making it impossible to look up a visible
socket in different netns.
On the other hand, while dumping sockets, they are filtered by netns. To
keep such code simple, let's add a new global hash table only for pathname
sockets and link them with sk_bind_node. Then we can keep all sockets in
each per-netns table and look up pathname sockets via the global table.
[0]: https://lore.kernel.org/netdev/B2AA3091-796D-475E-9A11-0021996E1C00@linux.ibm.com/
[1]: https://lore.kernel.org/netdev/5fb8d86f-b633-7552-8ba9-41e42f07c02a@gmail.com/
Changes:
v3:
* 1st: Update changelog s/named/pathname/
* 2nd: Fix checkpatch.pl CHECK by --strict option
v2: https://lore.kernel.org/netdev/20220702014447.93746-1-kuniyu@amazon.com/
* Add selftest
v1: https://lore.kernel.org/netdev/20220701072519.96097-1-kuniyu@amazon.com/
====================
Link: https://lore.kernel.org/r/20220702154818.66761-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch add a test that checks connect()ivity between two sockets:
unnamed socket -> bound socket
* SOCK_STREAM or SOCK_DGRAM
* pathname or abstract
* same or different netns
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit cf2f225e2653 ("af_unix: Put a socket into a per-netns hash table.")
accidentally broke user API for pathname sockets. A socket was able to
connect() to a pathname socket whose file was visible even if they were in
different network namespaces.
The commit puts all sockets into a per-netns hash table. As a result,
connect() to a pathname socket in a different netns fails to find it in the
caller's per-netns hash table and returns -ECONNREFUSED even when the task
can view the peer socket file.
We can reproduce this issue by:
Console A:
# python3
>>> from socket import *
>>> s = socket(AF_UNIX, SOCK_STREAM, 0)
>>> s.bind('test')
>>> s.listen(32)
Console B:
# ip netns add test
# ip netns exec test sh
# python3
>>> from socket import *
>>> s = socket(AF_UNIX, SOCK_STREAM, 0)
>>> s.connect('test')
Note when dumping sockets by sock_diag, procfs, and bpf_iter, they are
filtered only by netns. In other words, even if they are visible and
connect()able, all sockets in different netns are skipped while iterating
sockets. Thus, we need a fix only for finding a peer pathname socket.
This patch adds a global hash table for pathname sockets, links them with
sk_bind_node, and uses it in unix_find_socket_byinode(). By doing so, we
can keep sockets in per-netns hash tables and dump them easily.
Thanks to Sachin Sant and Leonard Crestez for reports, logs and a reproducer.
Fixes: cf2f225e2653 ("af_unix: Put a socket into a per-netns hash table.")
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Reported-by: Leonard Crestez <cdleonard@gmail.com>
Tested-by: Sachin Sant <sachinp@linux.ibm.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Tested-by: Leonard Crestez <cdleonard@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
can 2022-07-04
The 1st patch is by Oliver Hartkopp, targets the BCM CAN protocol and
converts a costly synchronize_rcu() to call_rcu() to fix a performance
regression.
Srinivas Neeli's patch for the xilinx_can driver drops the brp limit
down to 1, as only the pre-production silicon have an issue with a brp
of 1.
The next patch is by Duy Nguyen and fixes the data transmission on
R-Car V3U SoCs in the rcar_canfd driver.
Rhett Aultman's patch fixes a DMA memory leak in the gs_usb driver.
Liang He's patch removes an extra of_node_get() in the grcan driver.
The next 2 patches are by me, target the m_can driver and fix the
timestamp handling used for peripheral devices like the tcan4x5x.
Jimmy Assarsson contributes 3 patches for the kvaser_usb driver and
fixes CAN clock and bit timing related issues.
The remaining 5 patches target the mcp251xfd driver. Thomas Kopp
contributes 2 patches to improve the workaround for broken CRC when
reading the TBC register. 3 patches by me add a missing
hrtimer_cancel() during the ndo_stop() callback, and fix the reading
of the Device ID register.
* tag 'linux-can-fixes-for-5.19-20220704' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251xfd: mcp251xfd_register_get_dev_id(): fix endianness conversion
can: mcp251xfd: mcp251xfd_register_get_dev_id(): use correct length to read dev_id
can: mcp251xfd: mcp251xfd_stop(): add missing hrtimer_cancel()
can: mcp251xfd: mcp251xfd_regmap_crc_read(): update workaround broken CRC on TBC register
can: mcp251xfd: mcp251xfd_regmap_crc_read(): improve workaround handling for mcp2517fd
can: kvaser_usb: kvaser_usb_leaf: fix bittiming limits
can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression
can: kvaser_usb: replace run-time checks with struct kvaser_usb_driver_info
can: m_can: m_can_{read_fifo,echo_tx_event}(): shift timestamp to full 32 bits
can: m_can: m_can_chip_config(): actually enable internal timestamping
can: grcan: grcan_probe(): remove extra of_node_get()
can: gs_usb: gs_usb_open/close(): fix memory leak
can: rcar_canfd: Fix data transmission failed on R-Car V3U
Revert "can: xilinx_can: Limit CANFD brp to 2"
can: bcm: use call_rcu() instead of costly synchronize_rcu()
====================
Link: https://lore.kernel.org/r/20220704122613.1551119-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Another set of minor patches for Arm DTS files and soc specific
drivers:
- More reference counting bug fixes for DT nodes, and other trivial
code fixes
- Multiple code fixes for the Arm SCMI firmware driver to improve
compatibility with firmware implementations.
- A patch series for at91 to address power management issues from
using the wrong DT compatible properties.
- A series of patches to fix pad settings for NXP imx8mp to leave the
configuration untouched from the boot loader
- Additional DT fixes for qualcomm and NXP platforms
- A boot time fix for stm32mp15 DT
- Konrad Dybcio becomes an additional reviewer for the Qualcomm
platforms"
* tag 'soc-fixes-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
soc: qcom: smem: use correct format characters
ARM: dts: stm32: add missing usbh clock and fix clk order on stm32mp15
ARM: dts: stm32: delete fixed clock node on STM32MP15-SCMI
ARM: dts: stm32: DSI should use LSE SCMI clock on DK1/ED1 STM32 board
ARM: dts: stm32: use the correct clock source for CEC on stm32mp151
ARM: dts: stm32: fix pwr regulators references to use scmi
soc: ixp4xx/npe: Fix unused match warning
ARM: at91: pm: Mark at91_pm_secure_init as __init
ARM: at91: fix soc detection for SAM9X60 SiPs
ARM: dts: at91: sama5d2_icp: fix eeprom compatibles
ARM: dts: at91: sam9x60ek: fix eeprom compatible and size
ARM: at91: pm: use proper compatibles for sama7g5's rtc and rtt
ARM: at91: pm: use proper compatibles for sam9x60's rtc and rtt
ARM: at91: pm: use proper compatible for sama5d2's rtc
arm64: dts: qcom: msm8992-*: Fix vdd_lvs1_2-supply typo
firmware: arm_scmi: Remove usage of the deprecated ida_simple_xxx API
firmware: arm_scmi: Fix response size warning for OPTEE transport
arm64: dts: imx8mp-icore-mx8mp-edim2.2: correct pad settings
arm64: dts: imx8mp-phyboard-pollux-rdk: correct i2c2 & mmc settings
arm64: dts: imx8mp-phyboard-pollux-rdk: correct eqos pad settings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.19, round 2
Highlights:
-----------
-Fixes STM32MP15:
- Add missing usbh clock and fix clk order for usbh to avoid PLL
issue.
- Fix SCMI version: use scmi regulator and update missing SCMI
clocks to be able to correcly boot.
* tag 'stm32-dt-for-v5.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: add missing usbh clock and fix clk order on stm32mp15
ARM: dts: stm32: delete fixed clock node on STM32MP15-SCMI
ARM: dts: stm32: DSI should use LSE SCMI clock on DK1/ED1 STM32 board
ARM: dts: stm32: use the correct clock source for CEC on stm32mp151
ARM: dts: stm32: fix pwr regulators references to use scmi
Link: https://lore.kernel.org/r/1259e082-a3a4-96a5-ec9c-05dbb893a746@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When compiling with -Wformat, clang emits the following warnings:
drivers/soc/qcom/smem.c:847:41: warning: format specifies type 'unsigned
short' but the argument has type 'unsigned int' [-Wformat]
dev_err(smem->dev, "bad host %hu\n", remote_host);
~~~ ^~~~~~~~~~~
%u
./include/linux/dev_printk.h:144:65: note: expanded from macro 'dev_err'
dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
~~~ ^~~~~~~~~~~
./include/linux/dev_printk.h:110:23: note: expanded from macro 'dev_printk_index_wrap'
_p_func(dev, fmt, ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
drivers/soc/qcom/smem.c:852:47: warning: format specifies type 'unsigned
short' but the argument has type 'unsigned int' [-Wformat]
dev_err(smem->dev, "duplicate host %hu\n", remote_host);
~~~ ^~~~~~~~~~~
%u
./include/linux/dev_printk.h:144:65: note: expanded from macro 'dev_err'
dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
~~~ ^~~~~~~~~~~
./include/linux/dev_printk.h:110:23: note: expanded from macro 'dev_printk_index_wrap'
_p_func(dev, fmt, ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct one and change type of
remote_host to "u16" to match with other types.
Signed-off-by: Bill Wendling <morbo@google.com>
Tested-by: Justin Stitt <jstitt007@gmail.com>
Reviewed-by: Justin Stitt <jstitt007@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.19
A collection of fixes for v5.19, quite large but nothing major - a good
chunk of it is more stuff that was identified by mixer-test regarding
event generation.
|
|
The patch applies the same quirks used for SC-01 at firmware v1.1.0 to
the ones running v1.0.0, with respect to hard-coded sample rates.
I got two more units and successfully tested the patch series with both
firmwares.
The support is now complete (not accounting ASIO).
Signed-off-by: Egor Vorontsov <sdoregor@sdore.me>
Link: https://lore.kernel.org/r/20220627100041.2861494-2-sdoregor@sdore.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fiero SC-01 is a USB sound card with two mono inputs and a single
stereo output. The inputs are composed into a single stereo stream.
The device uses a vendor-provided driver on Windows and does not work
at all without it. The driver mostly provides ASIO functionality, but
also alters the way the sound card is queried for sample rates and
clocks.
ALSA queries those failing with an EPIPE (same as Windows 10 does).
Presumably, the vendor-provided driver does not query it at all, simply
matching by VID:PID. Thus, I consider this a buggy firmware and adhere
to a set of fixed endpoint quirks instead.
The soundcard has an internal clock. Implicit feedback mode is required
for the playback.
I have updated my device to v1.1.0 from a Windows 10 VM using a vendor-
provided binary prior to the development, hoping for it to just begin
working. The device provides no obvious way to downgrade the firmware,
and regardless, there's no binary available for v1.0.0 anyway.
Thus, I will be getting another unit to extend the patch with support
for that. Expected to be a simple copy-paste of the existing one,
though.
There were no previous reports of that device in context of Linux
anywhere. Other issues have been reported though, but that's out of the
scope.
Signed-off-by: Egor Vorontsov <sdoregor@sdore.me>
Link: https://lore.kernel.org/r/20220627100041.2861494-1-sdoregor@sdore.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixes headset detection on Clevo L140PU.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220624144109.3957-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Treat the claimed 96kHz 1ch in the descriptors as 48kHz 2ch, so that
the audio stream doesn't sound mono. Also fix initial stream
alignment, so that left and right channels are in the correct order.
Signed-off-by: John Veness <john-linux@pelago.org.uk>
Link: https://lore.kernel.org/r/20220624140757.28758-1-john-linux@pelago.org.uk
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In mcp251xfd_register_get_dev_id() the device ID register is read with
handcrafted SPI transfers. As all registers, this register is in
little endian. Further it is not naturally aligned in struct
mcp251xfd_map_buf_nocrc::data. However after the transfer the register
content is converted from big endian to CPU endianness not taking care
of being unaligned.
Fix the conversion by converting from little endian to CPU endianness
taking the unaligned source into account.
Side note: So far the register content is 0x0 on all mcp251xfd
compatible chips, and is only used for an informative printk.
Link: https://lore.kernel.org/all/20220627092859.809042-1-mkl@pengutronix.de
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
dev_id
The device ID register is 32 bits wide. The driver uses incorrectly
the size of a pointer to a u32 to calculate the length of the SPI
transfer. This results in a read of 2 registers on 64 bit platforms.
This is no problem on the Linux side, as the RX buffer of the SPI
transfer is large enough. In the mpc251xfd chip this results in the
read of an undocumented register. So far no problems were observed.
Fix the length of the SPI transfer to read the device ID register
only.
Link: https://lore.kernel.org/all/20220616094914.244440-1-mkl@pengutronix.de
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In commit 169d00a25658 ("can: mcp251xfd: add TX IRQ coalescing
support") software based TX coalescing was added to the driver. The
key idea is to keep the TX complete IRQ disabled for some time after
processing it and re-enable later by a hrtimer. When bringing the
interface down, this timer has to be stopped.
Add the missing hrtimer_cancel() of the tx_irq_time hrtimer to
mcp251xfd_stop().
Link: https://lore.kernel.org/all/20220620143942.891811-1-mkl@pengutronix.de
Fixes: 169d00a25658 ("can: mcp251xfd: add TX IRQ coalescing support")
Cc: stable@vger.kernel.org # v5.18
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
TBC register
The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit
c7eb923c3caf ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.
- If a CRC read error on the TBC register is detected and the first
byte is 0x00 or 0x80, the most significant bit of the first byte is
flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
For now we assume transferred data was OK.
New investigations and simulations indicate that the CRC send by the
device is calculated on correct data, and the data is incorrectly
received by the SPI host controller.
Use flipped instead of original data and update workaround description
in mcp251xfd_regmap_crc_read().
[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"
Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com
Fixes: c7eb923c3caf ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
