| Age | Commit message (Collapse) | Author |
|---|
|
It is observed that the echi ports of 3430 sdp board
are not working due to the random timing of programming
the associated GPIOs of the ULPI PHYs of the EHCI for reset.
If the PHYs are reset at during usbhs core driver, host ports will
not work because EHCI driver is loaded after the resetting PHYs.
The PHYs should be in reset state while initializing the EHCI
controller.
The code which does the GPIO pins associated with the PHYs
are programmed to reset is moved from the USB host core driver
to EHCI driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Andi Kleen and Tim Chen have reported that under certain circumstances
the extent cache statistics are causing scalability problems due to
cache line bounces.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.4-rc cycle
Here are the fixes I have queued for v3.4-rc cycle so far.
It includes fixes on many of the gadget drivers and a few
of the UDC controller drivers.
For musb we have a fix for a kernel oops when unloading
omap2430.ko glue layer, proper error checking for pm_runtime_*,
fix for the ULPI transfer block, and a bug fix in musb_cleanup_urb
routine.
For s3c-hsotg we have mostly FIFO-related fixes (proper TX FIFO
allocation, TX FIFO corruption fix in DMA mode) but also a couple
of minor fixes (fixing maximum packet size for ep0 and fix for
big transfers with DMA).
For the dwc3 driver we have a memory leak fix, a very important
fix for USB30CV with SetFeature tests and the hability to handle
ep0 requests bigger than wMaxPacketSize.
On top of that there's a bunch of gadget driver minor fixes adding
proper section annotations, and fixing up the sysfs interface for
doing device-initiated connect/disconnect and so on.
All patches have been pending on the mailing list for quite a while
and look good for your for-linus branch.
|
|
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The ux500 default config enables the db5500 and the db8500.
The incoming cpuidle driver uses the 'prcmu_enable_wakeups'
and the 'prcmu_set_power_state' functions but these ones
are defined but not implemented for the db5500, leading to
an unresolved symbol error at link time. In order to compile,
we have to disable the db5500 support which is not acceptable
for the default config.
I noticed there are also some other functions which are
defined but not implemented.
This patch fix this by removing the functions definitions
and move out of the config section the empty functions which
are normally used when the DB550 config is disabled.
Only the functions which are not implemented are concerned
by this modification.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Forget to unreserve after pinning. This can lead to problems in
soft reset and resume.
v2: rework patch as per Michel's suggestion.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
My rv515 card is very flaky with msi enabled. Every so often it loses a rearm
and never comes back, manually banging the rearm brings it back.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
You need to setup the dm9000 irq via gpio_to_irq() since
d0fbda9add (ARM: at91/gpio: drop PIN_BASE).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> [3.2+]
|
|
The flash size is 8MiB.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The real function is long gone and the empty one will generate warnings
when configured without Atmel serial:
arch/arm/mach-at91/at91rm9200_devices.c:1176: warning: 'struct at91_uart_config' declared inside parameter list
arch/arm/mach-at91/at91rm9200_devices.c:1176: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
at91_matrix_* macro's are used by at91_udc usb gadget driver,
which can be built as module, therefore we need to export the
variable containing matrix base address.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
After commit b55149529d26 (ARM: at91/PMC: make register base soc independent)
building atmel_usba_udc as a module fails with following message
ERROR: "at91_pmc_base" [drivers/usb/gadget/atmel_usba_udc.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Export symbol to allow driver to be built as a module again.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
After commit f363c40 (ARM: at91: make sdram/ddr register base soc independent)
building at91_cf as a module fails with:
ERROR: "at91_ramc_base" [drivers/pcmcia/at91_cf.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Export at91_ramc_base symbol to allow drivers using at91_ramc_*
functions to be built as modules again.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
[nicolas.ferre@atmel.com: modify slightly commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
After commit 5e9cf5e (ARM: at91: make ST (System Timer) soc independent)
building at91rm9200_wdt as a module fails with following message
ERROR: "at91_st_base" [drivers/watchdog/at91rm9200_wdt.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Export symbol to allow wdt driver to be built as a module again.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
[nicolas.ferre@atmel.com: use EXPORT_SYMBOL_GPL()]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Visstrim_M10 boards have 3 gpios to detect the
expansion board version attached and other 3 to
detect the motherboard revision.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Alex Gershgorin <alexg@meprolight.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This regression has been introduced in
commit ca9bfa7eed20ea34e862804e62aae10eb159edbb
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Jan 28 14:49:20 2012 +0100
drm/i915: fixup interlaced vertical timings confusion, part 1
Unfortunately that commit failed to take into account that the lvds
code does some special adjustements to the crtc timings for upscaling
an centering.
Fix this by explicitly computing crtc timings in the lvds mode fixup
function and setting a special flag in mode->private_flags if the crtc
timings have been adjusted.
v2: Add a comment to explain the new mode driver private flag,
suggested by Eugeni Dodonov.
v3: Kill the confusing and now redundant set_crtcinfo call in
intel_fixed_panel_mode, noticed by Chris Wilson.
Reported-and-Tested-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43071
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Some new drivers and changed Kconfig dependencies for the v3.4
kernel affecting the U8500 defconfig:
- The SOC config options are now brought in by default
- No need to explicitly select misc devices anymore
- I2C is selected by default
- We now have support for charging from the AB8500 so compile
in this
- The regulator framework needs to be explictly selected
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A recent change to a Kconfig configuration saw MACH_U8500
remove TPS6105X selection. In doing so Kconfig stopped
selecting REGULATORS, which is still required. This patch
sees UX500_SOC_DB8500 explicitly select it instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This can happen if the instruction is much longer than the maximum length,
or if insn->opnd_bytes is manually changed.
This patch also fixes warnings from -Wswitch-default flag.
Reported-by: Prashanth Nageshappa <prashanth@linux.vnet.ibm.com>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@linux.vnet.ibm.com>
Cc: Linux-mm <linux-mm@kvack.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Anton Arapov <anton@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120413032427.32577.42602.stgit@localhost.localdomain
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The 68EZ328/bootlogo.h is not actually used in the 68EZ328 platform code
at all. It is used by the 68VZ328 platform code though, so move it to be
with the rest of the 68VZ328 platform code.
Commit c0e0c89c089f4bd66dbbd1a44da90abe74fe3f02 ("fix broken boot logo
inclusion") modified the bootlogo code to not be included in asm code.
Modify 68VZ328/bootlogo.h so that the bootlogo bit map is named correctly
for direct use in the C code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The 68EZ328 and 68VZ328 platforms currently try to process their bootlogo.h
to make it clean to include in asm files. This is no longer used, the
bootlogo.h file is now included only in C code, so remove all the processing
code in the 68EZ328 and 68VZ328 Makefiles.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
|
|
Pull ARM fixes from Russell King:
"Nothing too disasterous, the biggest thing being the removal of the
regulator support for vcore in the AMBA driver; only one SoC was using
this and it got broken during the last merge window, which then
started causing problems for other people. Mutual agreement was
reached for it to be removed."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
ARM: 7383/1: nommu: populate vectors page from paging_init
ARM: 7381/1: nommu: fix typo in mm/Kconfig
ARM: 7380/1: DT: do not add a zero-sized memory property
ARM: 7379/1: DT: fix atags_to_fdt() second call site
ARM: 7366/3: amba: Remove AMBA level regulator support
ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented
|
|
The 'max' range needs to be unsigned, since the size of the user address
space is bigger than 2GB.
We know that 'count' is positive in 'long' (that is checked in the
caller), so we will truncate 'max' down to something that fits in a
signed long, but before we actually do that, that comparison needs to be
done in unsigned.
Bug introduced in commit 92ae03f2ef99 ("x86: merge 32/64-bit versions of
'strncpy_from_user()' and speed it up"). On x86-64 you can't trigger
this, since the user address space is much smaller than 63 bits, and on
x86-32 it works in practice, since you would seldom hit the strncpy
limits anyway.
I had actually tested the corner-cases, I had only tested them on
x86-64. Besides, I had only worried about the case of a pointer *close*
to the end of the address space, rather than really far away from it ;)
This also changes the "we hit the user-specified maximum" to return
'res', for the trivial reason that gcc seems to generate better code
that way. 'res' and 'count' are the same in that case, so it really
doesn't matter which one we return.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
c5905afb0 ("static keys: Introduce 'struct static_key'...") renamed
struct jump_label_key to struct static_key. Fixup ARM for this to
eliminate these build warnings:
include/linux/jump_label.h:113:2:
warning: passing argument 1 of 'arch_static_branch' from incompatible pointer type
include/asm/jump_label.h:17:82:
note: expected 'struct jump_label_key *' but argument is of type 'struct static_key *'
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Currently when ThumbEE is not enabled (!CONFIG_ARM_THUMBEE) the ThumbEE
register states are not saved/restored at context switch. The default state
of the ThumbEE Ctrl register (TEECR) allows userspace accesses to the
ThumbEE Base Handler register (TEEHBR). This can cause unexpected behaviour
when people use ThumbEE on !CONFIG_ARM_THUMBEE kernels, as well as allowing
covert communication - eg between userspace tasks running inside chroot
jails.
This patch sets up TEECR in order to prevent user-space access to TEEHBR
when !CONFIG_ARM_THUMBEE. In this case, tasks are sent SIGILL if they try to
access TEEHBR.
Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
If a bank of memory spanning the 4GB boundary is added on a !CONFIG_LPAE
kernel then we will hang early during boot since the memory bank will
have wrapped around to zero.
This patch truncates memory banks for !LPAE configurations when the end
address is not representable in 32 bits.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
During booting of cpu1, there is a short window where cpu1
is online, but not active where cpu1 is occupied by waiting
to become active. If cpu0 then decides to schedule something
on cpu1 and wait for it to complete, before cpu0 has set
cpu1 active, we have a deadlock.
Typically it's this CPU frequency transition that happens at
this time, so let's just not wait for it to happen, it will
happen whenever the CPU eventually comes online instead.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 26f41062f28d ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.
First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one). Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt. Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.
All of this actually caused resume failures for some devices on Mikko's
system.
To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value. Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: a few more SoC fixes for 3.4-rc" from Olof Johansson:
- A handful of warning and build fixes for Qualcomm MSM
- Build/warning and bug fixes for Samsung Exynos
- A fix from Rob Herring that removes misplaced interrupt-parent
properties from a few device trees
- A fix to OMAP dealing with cpufreq build errors, removing some of the
offending code since it was redundant anyway
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
ARM: dts: remove blank interrupt-parent properties
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
ARM: EXYNOS: Add PDMA and MDMA physical base address defines
ARM: S5PV210: Fix compiler warning in dma.c file
ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
ARM: EXYNOS: Add missing definition for IRQ_I2S0
ARM: S5PV210: fix unused LDO supply field from wm8994_pdata
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull another round of sound fixes from Takashi Iwai:
"A few regression fixes for Realtek HD-audio codecs, mainly specific to
some laptop models."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
ALSA: hda/realtek - Add a fixup entry for Acer Aspire 8940G
ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
ALSA: hda/realtek - Add a few ALC882 model strings back
|
|
Commit 18a4d0a22ed6 ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.
Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As reported by David Gibson, current code handles PAGE_SIZE != 4k
completely wrong which can lead to guest memory corruption errors:
- page_to_balloon_pfn is wrong: e.g. on system with 64K page size
it gives the same pfn value for 16 different pages.
- we also need to convert back to linux pfns when we free.
- for each linux page we need to tell host about multiple balloon
pages, but code only adds one pfn to the array.
This patch fixes all that, tested with a 64k ppc64 kernel.
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Although virtio config space fields are usually in guest-native endian,
the spec for the virtio balloon device explicitly states that both fields
in its config space are little-endian.
However, the current virtio_balloon driver does not have a suitable endian
swap for the 'num_pages' field, although it does have one for the 'actual'
field. This patch corrects the bug, adding sparse annotation while we're
at it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf tooling fixes from Arnaldo Carvalho de Melo:
. Properly handle ~/.debug, the build id cache, when it is a symlink,
fix from Chanho Park
. Fixes for the parser generation process, from Jiri Olsa and Namhyung Kim
. Fix build when NO_GTK2 is specified, From Stephane Eranian
. When a machine is not found, bump the relevant error stat but return
0, so that we correctly move to the next perf event. Fix from Jiri Olsa
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.4-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
ARM: EXYNOS: Add PDMA and MDMA physical base address defines
ARM: S5PV210: Fix compiler warning in dma.c file
ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
ARM: EXYNOS: Add missing definition for IRQ_I2S0
ARM: S5PV210: fix unused LDO supply field from wm8994_pdata
|
|
Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables. Remove it.
Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.
Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
These were incorrectly introduced and can cause problems for of_irq_init.
The correct way to define a root controller is no interrupt-parent set at
all or the interrupt-parent is set to the root controller itself when
inherited from a parent node.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into fixes
From David Brown:
"Here are some fixes for msm that fix problems caused by the latest
ARM code. The ones from Daniel remove unneeded fixups that now
cause compilation failures. Mine fix section mismatches, that were
incompletely fixed earlier."
* 'msm-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
|
|
If a '$PERF_BUILDID_DIR'(typically $HOME/.debug) is a symbolic link
directory, cutting of the path will fail.
Here is an example where a buildid directory is a symbolic link.
/ # ls -al /root
lrwxrwxrwx 1 root root 13 Mar 26 2012 /root -> opt/home/root
/ # cd ~
/opt/home/root # perf record -a -g sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.322 MB perf.data (~14057 samples) ]
/opt/home/root # perf archive
tar: Removing leading `/' from member names
Now please run:
$ tar xvf perf.data.tar.bz2 -C ~/.debug
wherever you need to run 'perf report' on.
/opt/home/root # mkdir temp
/opt/home/root # tar xf perf.data.tar.bz2 -C ./temp
/opt/home/root # find ./temp -name "*kernel*"
./temp/opt/home/root/.debug/[kernel.kallsyms]
-> If successfully cut off the path, [kernel.kallsyms] is located
in top of the archived file.
This patch enables to cut correctly even if the buildid directory
is a symbolic link.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333348109-12598-1-git-send-email-chanho61.park@samsung.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The commit 65f3e56e0c81 ("perf tools: Remove auto-generated bison/flex
files") removed those files from git, so they'll be listed on untracked
files after building perf. Fix it.
Signed-off-by: Namhyung Kim <namhyung.kim@lge.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333948274-20043-1-git-send-email-namhyung.kim@lge.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Currently the parsers objects (bison/flex related) are each time perf
is built. No matter the generated files are already in place, the
parser generation is executed every time.
Changing the rules to have proper flex/bison objects generation
dependencies.
The parsers code is not rebuilt until the flex/bison source files
are touched. Also when flex/bison source is changed, only dependent
objects are rebuilt.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1334140791-3024-1-git-send-email-jolsa@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add config dependency for Exynos4 and Exynos5 device tree enabled machine
files on config options ARCH_EXYNOS4 and ARCH_EXYNOS5 respectively.
Enabling machine support without proper ARCH support enabled is incorrect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tool fixes from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf kvm: Finding struct machine fails for PERF_RECORD_MMAP
perf annotate: Validate addr in symbol__inc_addr_samples
perf hists browser: Fix NULL deref in hists browsing code
perf hists: Catch and handle out-of-date hist entry maps.
perf annotate: Fix hist decay
perf top: Add intel_idle to the skip list
|
|
GCC's NULL is actually __null, which allows detecting some questionable
NULL usage and warn about it. Moreover each platform/compiler should
have its own stddef.h anyway (which is different from linux/stddef.h).
So there's no good reason to leak kernel's NULL to userspace and
override what the compiler provides.
Signed-off-by: Luboš Luňák <l.lunak@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The atmel_mxt_ts driver has been extended to support more 'configuration
objects' in commit 81c88a711 ("Input: atmel_mxt_ts - update object list"),
what broke the configuration values for NURI board. These values are
optional anyway, so remove them to get the driver working correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
On some versions of NURI and UniversalC210 boards, camera clocks are
routed directly to xusbxti clock source. This patch sets the correct
value for this clock to let usb and camera sensors to work correctly and
avoid division by zero on driver's probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
