| Age | Commit message (Collapse) | Author |
|---|
|
Size should be 64KiB instead of 92KiB.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On the GP EVM, the ambient light sensor is limited to 100KHz on the
I2C bus.
So use 100kHz for I2C on the GP EVM due to this limitation on the
ambient light sensor.
Reported-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
fixes-rc3
|
|
The 8th NAND partition should be named "NAND.u-boot-env.backup1"
instead of "NAND.u-boot-env". This is to be consistent with other
TI boards as well as u-boot.
CC: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The I2C3 pins are taken from pads E21 (GPIO6_14) and
F20 (GPIO6_15). Use the right pinmux register and mode.
Also set the I2C3 bus frequency to a safer 400KHz than
3.4Mhz.
CC: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There is a following AB-BA dependency between cpu_hotplug.lock and
cpuidle_lock:
1) cpu_hotplug.lock -> cpuidle_lock
enable_nonboot_cpus()
_cpu_up()
cpu_hotplug_begin()
LOCK(cpu_hotplug.lock)
cpu_notify()
...
acpi_processor_hotplug()
cpuidle_pause_and_lock()
LOCK(cpuidle_lock)
2) cpuidle_lock -> cpu_hotplug.lock
acpi_os_execute_deferred() workqueue
...
acpi_processor_cst_has_changed()
cpuidle_pause_and_lock()
LOCK(cpuidle_lock)
get_online_cpus()
LOCK(cpu_hotplug.lock)
Fix this by reversing the order acpi_processor_cst_has_changed() does
thigs -- let it first execute the protection against CPU hotplug by
calling get_online_cpus() and obtain the cpuidle lock only after that (and
perform the symmentric change when allowing CPUs hotplug again and
dropping cpuidle lock).
Spotted by lockdep.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The _SUN device indentification object is not guaranteed to return
the same value every time it is executed, so we should not cache its
return value, but rather execute it every time as needed. If it is
cached, an incorrect stale value may be used in some situations.
This issue was exposed by commit 202317a573b2 (ACPI / scan: Add
acpi_device objects for all device nodes in the namespace). Fix it
by avoiding to cache the return value of _SUN.
Fixes: 202317a573b2 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The current code just returns -EINVAL because mode can't be equal to
both 1 and 2.
Also this function is messy so I have cleaned it up:
1) Remove initializers like "int time = -1". Initializing variables to
garbage values turns off GCC's uninitialized variable warnings so it
can lead to bugs.
2) Use kstrtoint() instead of sscanf().
3) Use SCI_KBD_MODE_FNZ and SCI_KBD_MODE_AUTO instead of magic numbers 1
and 2.
4) Don't check for "mode == -1" because that can't happen.
5) Preserve the error code from toshiba_kbd_illum_status_set().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs bug fixes from Jaegeuk Kim:
"This series includes patches to:
- fix recovery routines
- fix bugs related to inline_data/xattr
- fix when casting the dentry names
- handle EIO or ENOMEM correctly
- fix memory leak
- fix lock coverage"
* tag 'for-f2fs-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (28 commits)
f2fs: reposition unlock_new_inode to prevent accessing invalid inode
f2fs: fix wrong casting for dentry name
f2fs: simplify by using a literal
f2fs: truncate stale block for inline_data
f2fs: use macro for code readability
f2fs: introduce need_do_checkpoint for readability
f2fs: fix incorrect calculation with total/free inode num
f2fs: remove rename and use rename2
f2fs: skip if inline_data was converted already
f2fs: remove rewrite_node_page
f2fs: avoid double lock in truncate_blocks
f2fs: prevent checkpoint during roll-forward
f2fs: add WARN_ON in f2fs_bug_on
f2fs: handle EIO not to break fs consistency
f2fs: check s_dirty under cp_mutex
f2fs: unlock_page when node page is redirtied out
f2fs: introduce f2fs_cp_error for readability
f2fs: give a chance to mount again when encountering errors
f2fs: trigger release_dirty_inode in f2fs_put_super
f2fs: don't skip checkpoint if there is no dirty node pages
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull key subsystem fixes from James Morris:
"Fixes for the keys subsystem, one of which addresses a use-after-free
bug"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
PEFILE: Relax the check on the length of the PKCS#7 cert
KEYS: Fix use-after-free in assoc_array_gc()
KEYS: Fix public_key asymmetric key subtype name
KEYS: Increase root_maxkeys and root_maxbytes sizes
|
|
Structure name and variable name were erroneously interchanged
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
[ Also removed pointless cast from "void *". - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 fixes from Will Deacon:
"Another handful of arm64 fixes here. They address some issues found
by running smatch on the arch code (ignoring the false positives) and
also stop 32-bit Android from losing track of its stack.
There's one additional irq migration fix in the pipeline, but it came
in after I'd tagged and tested this set.
- a few fixes for real issues found by smatch (after Dan's talk at KS)
- revert the /proc/cpuinfo changes merged during the merge window.
We've opened a can of worms here, so we need to find out where we
stand before we change this interface.
- implement KSTK_ESP for compat tasks, otherwise 32-bit Android gets
confused wondering where its [stack] has gone
- misc fixes (fpsimd context handling, crypto, ...)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "arm64: cpuinfo: print info for all CPUs"
arm64: fix bug for reloading FPSIMD state after cpu power off
arm64: report correct stack pointer in KSTK_ESP for compat tasks
arm64: Add brackets around user_stack_pointer()
arm64: perf: don't rely on layout of pt_regs when grabbing sp or pc
arm64: ptrace: fix compat reg getter/setter return values
arm64: ptrace: fix compat hardware watchpoint reporting
arm64: Remove unused variable in head.S
arm64/crypto: remove redundant update of data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"This fixes an ARM allmodconfig build problem:
Remove module option for ST Microelectronics SPEAr13xx"
* tag 'pci-v3.17-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: spear: Remove module option
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED fix from Bryan Wu:
"Hugh, Jiri and many other people found a kernel oops due to a LED
change merged recently. Now the right fix might just revert it and
avoid the kernel oops"
* 'leds-fixes-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
Revert "leds: convert blink timer to workqueue"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.17
A few more driver specific fixes on top of the currently pending fixes
(which are already in your tree but not Linus').
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu into core/urgent
Pull an RCU fix from Paul E. McKenney:
"This series contains a single commit fixing an initialization bug
reported by Amit Shah and fixed by Pranith Kumar (and tested by Amit).
This bug results in a boot-time hang in callback-offloaded configurations
where callbacks were posted before the offloading ('rcuo') kthreads
were created."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
fc95ca7284bc54953165cba76c3228bd2cdb9591 introduces a memset in
kvmppc_alloc_hpt since the general CMA doesn't clear the memory it
allocates.
However, the size argument passed to memset is computed from a signed value
and its signed bit is extended by the cast the compiler is doing. This lead
to extremely large size value when dealing with order value >= 31, and
almost all the memory following the allocated space is cleaned. As a
consequence, the system is panicing and may even fail spawning the kdump
kernel.
This fix makes use of an unsigned value for the memset's size argument to
avoid sign extension. Among this fix, another shift operation which may
lead to signed extended value too is also fixed.
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://people.freedesktop.org/~thomash/linux into drm-fixes
Two vmwgfx fixes, marked for stable as well
* 'vmwgfx-fixes-3.17' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix a potential infinite spin waiting for fifo idle
drm/vmwgfx: Fix an incorrect OOM return value
|
|
Relax the check on the length of the PKCS#7 cert as it appears that the PE
file wrapper size gets rounded up to the nearest 8.
The debugging output looks like this:
PEFILE: ==> verify_pefile_signature()
PEFILE: ==> pefile_parse_binary()
PEFILE: checksum @ 110
PEFILE: header size = 200
PEFILE: cert = 968 @547be0 [68 09 00 00 00 02 02 00 30 82 09 56 ]
PEFILE: sig wrapper = { 968, 200, 2 }
PEFILE: Signature data not PKCS#7
The wrapper is the first 8 bytes of the hex dump inside []. This indicates a
length of 0x968 bytes, including the wrapper header - so 0x960 bytes of
payload.
The ASN.1 wrapper begins [ ... 30 82 09 56 ]. That indicates an object of size
0x956 - a four byte discrepency, presumably just padding for alignment
purposes.
So we just check that the ASN.1 container is no bigger than the payload and
reduce the recorded size appropriately.
Whilst we're at it, allow shorter PKCS#7 objects that manage to squeeze within
127 or 255 bytes. It's just about conceivable if no X.509 certs are included
in the PKCS#7 message.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
An edit script should be considered inaccessible by a function once it has
called assoc_array_apply_edit() or assoc_array_cancel_edit().
However, assoc_array_gc() is accessing the edit script just after the
gc_complete: label.
Reported-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
cc: shemming@brocade.com
cc: paulmck@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
The length of the name of an asymmetric key subtype must be stored in struct
asymmetric_key_subtype::name_len so that it can be matched by a search for
"<subkey_name>:<partial_fingerprint>". Fix the public_key subtype to have
name_len set.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Now that NFS client uses the kernel key ring facility to store the NFSv4
id/gid mappings, the defaults for root_maxkeys and root_maxbytes need to be
substantially increased.
These values have been soak tested:
https://bugzilla.redhat.com/show_bug.cgi?id=1033708#c73
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
It should have been removed with commit d1b6848590af
("cpufreq / intel_pstate: Optimize intel_pstate_set_policy")
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Many CPUs do not support complete set of RAPL domains, as a
result this detection failed message is very misleading and
can be annoying.
[ 5.082632] intel_rapl: RAPL domain core detection failed
[ 5.088370] intel_rapl: RAPL domain uncore detection failed
So lower the warning message to info and only print out the RAPL
domains that are supported.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
I've confirmed that monitoring the package power usage as well as setting power
limits appear to be working as expected. Supports the package and dram domains.
Tested aginst cpu:
Intel(R) Xeon(R) CPU E5-2650 v3 @ 2.30GHz
Signed-off-by: Jason Baron <jbaron@akamai.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After commit d431cbc53cb7 (PM / sleep: Simplify sleep states sysfs
interface code) the pm_states[] array is not populated initially,
which causes setup_test_suspend() to always fail and the suspend
testing during boot doesn't work any more.
Fix the problem by using pm_labels[] instead of pm_states[] in
setup_test_suspend() and storing a pointer to the label of the
sleep state to test rather than the number representing it,
because the connection between the state numbers and labels is
only established by suspend_set_ops().
Fixes: d431cbc53cb7 (PM / sleep: Simplify sleep states sysfs interface code)
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On the Toshiba Tecra Z40, after a suspend-to-disk, some FN hotkeys
driven by toshiba_acpi are not functional.
Calling the ACPI object ENAB on resume makes them back alive.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
'asoc/fix/da732x', 'asoc/fix/omap', 'asoc/fix/rsnd', 'asoc/fix/rt5640', 'asoc/fix/rt5677', 'asoc/fix/simple' and 'asoc/fix/tegra' into asoc-linus
|
|
|
|
This is a follow-up patch to commit 49458e83082d ("ideapad-laptop:
Constify DMI table and other r/o variables") to do what its commit
message says. The actual commit differs from the patch posted at
https://www.mail-archive.com/platform-driver-x86@vger.kernel.org/msg05340.html
significantly, probably due to a bad merge conflict resolution. Fix up
the mess and constify the DMI table for real and fix the bogus
double-const of ideapad_rfk_data[].
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Matthew Garrett <matthew.garrett@nebula.com>
Cc: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
We ran into a case on ppc64 running mariadb where io_getevents would
return zeroed out I/O events. After adding instrumentation, it became
clear that there was some missing synchronization between reading the
tail pointer and the events themselves. This small patch fixes the
problem in testing.
Thanks to Zach for helping to look into this, and suggesting the fix.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org
|
|
Analogous to commit 8858d88a25142544843869f0cd3e6654aa7b4aec
that fixed commit 70b41abc151f9
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.
For some reason I forgot to fix this on the Snowball. Fix
this up by marking the node disabled again.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
This reverts commit 8b37e1bef5a6b60e949e28a4db3006e4b00bd758.
It's broken as it changes led_blink_set() in a way that it can now sleep
(while synchronously waiting for workqueue to be cancelled). That's a
problem, because it's possible that this function gets called from atomic
context (tpt_trig_timer() takes a readlock and thus disables preemption).
This has been brought up 3 weeks ago already [1] but no proper fix has
materialized, and I keep seeing the problem since 3.17-rc1.
[1] https://lkml.org/lkml/2014/8/16/128
BUG: sleeping function called from invalid context at kernel/workqueue.c:2650
in_atomic(): 1, irqs_disabled(): 0, pid: 2335, name: wpa_supplicant
5 locks held by wpa_supplicant/2335:
#0: (rtnl_mutex){+.+.+.}, at: [<ffffffff814c7c92>] rtnl_lock+0x12/0x20
#1: (&wdev->mtx){+.+.+.}, at: [<ffffffffc06e649c>] cfg80211_mgd_wext_siwessid+0x5c/0x180 [cfg80211]
#2: (&local->mtx){+.+.+.}, at: [<ffffffffc0817dea>] ieee80211_prep_connection+0x17a/0x9a0 [mac80211]
#3: (&local->chanctx_mtx){+.+.+.}, at: [<ffffffffc08081ed>] ieee80211_vif_use_channel+0x5d/0x2a0 [mac80211]
#4: (&trig->leddev_list_lock){.+.+..}, at: [<ffffffffc081e68c>] tpt_trig_timer+0xec/0x170 [mac80211]
CPU: 0 PID: 2335 Comm: wpa_supplicant Not tainted 3.17.0-rc3 #1
Hardware name: LENOVO 7470BN2/7470BN2, BIOS 6DET38WW (2.02 ) 12/19/2008
ffff8800360b5a50 ffff8800751f76d8 ffffffff8159e97f ffff8800360b5a30
ffff8800751f76e8 ffffffff810739a5 ffff8800751f77b0 ffffffff8106862f
ffffffff810685d0 0aa2209200000000 ffff880000000004 ffff8800361c59d0
Call Trace:
[<ffffffff8159e97f>] dump_stack+0x4d/0x66
[<ffffffff810739a5>] __might_sleep+0xe5/0x120
[<ffffffff8106862f>] flush_work+0x5f/0x270
[<ffffffff810685d0>] ? mod_delayed_work_on+0x80/0x80
[<ffffffff810945ca>] ? mark_held_locks+0x6a/0x90
[<ffffffff81068a5f>] ? __cancel_work_timer+0x6f/0x100
[<ffffffff810946ed>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[<ffffffff81068a6b>] __cancel_work_timer+0x7b/0x100
[<ffffffff81068b0e>] cancel_delayed_work_sync+0xe/0x10
[<ffffffff8147cf3b>] led_blink_set+0x1b/0x40
[<ffffffffc081e6b0>] tpt_trig_timer+0x110/0x170 [mac80211]
[<ffffffffc081ecdd>] ieee80211_mod_tpt_led_trig+0x9d/0x160 [mac80211]
[<ffffffffc07e4278>] __ieee80211_recalc_idle+0x98/0x140 [mac80211]
[<ffffffffc07e59ce>] ieee80211_idle_off+0xe/0x10 [mac80211]
[<ffffffffc0804e5b>] ieee80211_add_chanctx+0x3b/0x220 [mac80211]
[<ffffffffc08062e4>] ieee80211_new_chanctx+0x44/0xf0 [mac80211]
[<ffffffffc080838a>] ieee80211_vif_use_channel+0x1fa/0x2a0 [mac80211]
[<ffffffffc0817df8>] ieee80211_prep_connection+0x188/0x9a0 [mac80211]
[<ffffffffc081c246>] ieee80211_mgd_auth+0x256/0x2e0 [mac80211]
[<ffffffffc07eab33>] ieee80211_auth+0x13/0x20 [mac80211]
[<ffffffffc06cb006>] cfg80211_mlme_auth+0x106/0x270 [cfg80211]
[<ffffffffc06ce085>] cfg80211_conn_do_work+0x155/0x3b0 [cfg80211]
[<ffffffffc06cf670>] cfg80211_connect+0x3f0/0x540 [cfg80211]
[<ffffffffc06e6148>] cfg80211_mgd_wext_connect+0x158/0x1f0 [cfg80211]
[<ffffffffc06e651e>] cfg80211_mgd_wext_siwessid+0xde/0x180 [cfg80211]
[<ffffffffc06e36c0>] ? cfg80211_wext_giwessid+0x50/0x50 [cfg80211]
[<ffffffffc06e36dd>] cfg80211_wext_siwessid+0x1d/0x40 [cfg80211]
[<ffffffff81584d0c>] ioctl_standard_iw_point+0x14c/0x3e0
[<ffffffff810946ed>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[<ffffffff8158502a>] ioctl_standard_call+0x8a/0xd0
[<ffffffff81584fa0>] ? ioctl_standard_iw_point+0x3e0/0x3e0
[<ffffffff81584b76>] wireless_process_ioctl.constprop.10+0xb6/0x100
[<ffffffff8158521d>] wext_handle_ioctl+0x5d/0xb0
[<ffffffff814cfb29>] dev_ioctl+0x329/0x620
[<ffffffff810946ed>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[<ffffffff8149c7f2>] sock_ioctl+0x142/0x2e0
[<ffffffff811b0140>] do_vfs_ioctl+0x300/0x520
[<ffffffff815a67fb>] ? sysret_check+0x1b/0x56
[<ffffffff810946ed>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[<ffffffff811b03e1>] SyS_ioctl+0x81/0xa0
[<ffffffff815a67d6>] system_call_fastpath+0x1a/0x1f
wlan0: send auth to 00:0b:6b:3c:8c:e4 (try 1/3)
wlan0: authenticated
wlan0: associate with 00:0b:6b:3c:8c:e4 (try 1/3)
wlan0: RX AssocResp from 00:0b:6b:3c:8c:e4 (capab=0x431 status=0 aid=2)
wlan0: associated
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
cfg80211: Calling CRDA for country: NA
wlan0: Limiting TX power to 27 (27 - 0) dBm as advertised by 00:0b:6b:3c:8c:e4
=================================
[ INFO: inconsistent lock state ]
3.17.0-rc3 #1 Not tainted
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/0/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
((&(&led_cdev->blink_work)->work)){+.?...}, at: [<ffffffff810685d0>] flush_work+0x0/0x270
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff81094dbe>] __lock_acquire+0x30e/0x1a30
[<ffffffff81096c81>] lock_acquire+0x91/0x110
[<ffffffff81068608>] flush_work+0x38/0x270
[<ffffffff81068a6b>] __cancel_work_timer+0x7b/0x100
[<ffffffff81068b0e>] cancel_delayed_work_sync+0xe/0x10
[<ffffffff8147cf3b>] led_blink_set+0x1b/0x40
[<ffffffffc081e6b0>] tpt_trig_timer+0x110/0x170 [mac80211]
[<ffffffffc081ecdd>] ieee80211_mod_tpt_led_trig+0x9d/0x160 [mac80211]
[<ffffffffc07e4278>] __ieee80211_recalc_idle+0x98/0x140 [mac80211]
[<ffffffffc07e59ce>] ieee80211_idle_off+0xe/0x10 [mac80211]
[<ffffffffc0804e5b>] ieee80211_add_chanctx+0x3b/0x220 [mac80211]
[<ffffffffc08062e4>] ieee80211_new_chanctx+0x44/0xf0 [mac80211]
[<ffffffffc080838a>] ieee80211_vif_use_channel+0x1fa/0x2a0 [mac80211]
[<ffffffffc0817df8>] ieee80211_prep_connection+0x188/0x9a0 [mac80211]
[<ffffffffc081c246>] ieee80211_mgd_auth+0x256/0x2e0 [mac80211]
[<ffffffffc07eab33>] ieee80211_auth+0x13/0x20 [mac80211]
[<ffffffffc06cb006>] cfg80211_mlme_auth+0x106/0x270 [cfg80211]
[<ffffffffc06ce085>] cfg80211_conn_do_work+0x155/0x3b0 [cfg80211]
[<ffffffffc06cf670>] cfg80211_connect+0x3f0/0x540 [cfg80211]
[<ffffffffc06e6148>] cfg80211_mgd_wext_connect+0x158/0x1f0 [cfg80211]
[<ffffffffc06e651e>] cfg80211_mgd_wext_siwessid+0xde/0x180 [cfg80211]
[<ffffffffc06e36dd>] cfg80211_wext_siwessid+0x1d/0x40 [cfg80211]
[<ffffffff81584d0c>] ioctl_standard_iw_point+0x14c/0x3e0
[<ffffffff8158502a>] ioctl_standard_call+0x8a/0xd0
[<ffffffff81584b76>] wireless_process_ioctl.constprop.10+0xb6/0x100
[<ffffffff8158521d>] wext_handle_ioctl+0x5d/0xb0
[<ffffffff814cfb29>] dev_ioctl+0x329/0x620
[<ffffffff8149c7f2>] sock_ioctl+0x142/0x2e0
[<ffffffff811b0140>] do_vfs_ioctl+0x300/0x520
[<ffffffff811b03e1>] SyS_ioctl+0x81/0xa0
[<ffffffff815a67d6>] system_call_fastpath+0x1a/0x1f
irq event stamp: 493416
hardirqs last enabled at (493416): [<ffffffff81068a5f>] __cancel_work_timer+0x6f/0x100
hardirqs last disabled at (493415): [<ffffffff81067e9f>] try_to_grab_pending+0x1f/0x160
softirqs last enabled at (493408): [<ffffffff81053ced>] _local_bh_enable+0x1d/0x50
softirqs last disabled at (493409): [<ffffffff81054c75>] irq_exit+0xa5/0xb0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock((&(&led_cdev->blink_work)->work));
<Interrupt>
lock((&(&led_cdev->blink_work)->work));
*** DEADLOCK ***
2 locks held by swapper/0/0:
#0: (((&tpt_trig->timer))){+.-...}, at: [<ffffffff810b4c50>] call_timer_fn+0x0/0x180
#1: (&trig->leddev_list_lock){.+.?..}, at: [<ffffffffc081e68c>] tpt_trig_timer+0xec/0x170 [mac80211]
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.17.0-rc3 #1
Hardware name: LENOVO 7470BN2/7470BN2, BIOS 6DET38WW (2.02 ) 12/19/2008
ffffffff8246eb30 ffff88007c203b00 ffffffff8159e97f ffffffff81a194c0
ffff88007c203b50 ffffffff81599c29 0000000000000001 ffffffff00000001
ffff880000000000 0000000000000006 ffffffff81a194c0 ffffffff81093ad0
Call Trace:
<IRQ> [<ffffffff8159e97f>] dump_stack+0x4d/0x66
[<ffffffff81599c29>] print_usage_bug+0x1f4/0x205
[<ffffffff81093ad0>] ? check_usage_backwards+0x140/0x140
[<ffffffff810944d3>] mark_lock+0x223/0x2b0
[<ffffffff81094d60>] __lock_acquire+0x2b0/0x1a30
[<ffffffff81096c81>] lock_acquire+0x91/0x110
[<ffffffff810685d0>] ? mod_delayed_work_on+0x80/0x80
[<ffffffffc081e5a0>] ? __ieee80211_get_rx_led_name+0x10/0x10 [mac80211]
[<ffffffff81068608>] flush_work+0x38/0x270
[<ffffffff810685d0>] ? mod_delayed_work_on+0x80/0x80
[<ffffffff810945ca>] ? mark_held_locks+0x6a/0x90
[<ffffffff81068a5f>] ? __cancel_work_timer+0x6f/0x100
[<ffffffffc081e5a0>] ? __ieee80211_get_rx_led_name+0x10/0x10 [mac80211]
[<ffffffff8109469d>] ? trace_hardirqs_on_caller+0xad/0x1c0
[<ffffffffc081e5a0>] ? __ieee80211_get_rx_led_name+0x10/0x10 [mac80211]
[<ffffffff81068a6b>] __cancel_work_timer+0x7b/0x100
[<ffffffff81068b0e>] cancel_delayed_work_sync+0xe/0x10
[<ffffffff8147cf3b>] led_blink_set+0x1b/0x40
[<ffffffffc081e6b0>] tpt_trig_timer+0x110/0x170 [mac80211]
[<ffffffff810b4cc5>] call_timer_fn+0x75/0x180
[<ffffffff810b4c50>] ? process_timeout+0x10/0x10
[<ffffffffc081e5a0>] ? __ieee80211_get_rx_led_name+0x10/0x10 [mac80211]
[<ffffffff810b50ac>] run_timer_softirq+0x1fc/0x2f0
[<ffffffff81054805>] __do_softirq+0x115/0x2e0
[<ffffffff81054c75>] irq_exit+0xa5/0xb0
[<ffffffff810049b3>] do_IRQ+0x53/0xf0
[<ffffffff815a74af>] common_interrupt+0x6f/0x6f
<EOI> [<ffffffff8147b56e>] ? cpuidle_enter_state+0x6e/0x180
[<ffffffff8147b732>] cpuidle_enter+0x12/0x20
[<ffffffff8108bba0>] cpu_startup_entry+0x330/0x360
[<ffffffff8158fb51>] rest_init+0xc1/0xd0
[<ffffffff8158fa90>] ? csum_partial_copy_generic+0x170/0x170
[<ffffffff81af3ff2>] start_kernel+0x44f/0x45a
[<ffffffff81af399c>] ? set_init_arg+0x53/0x53
[<ffffffff81af35ad>] x86_64_start_reservations+0x2a/0x2c
[<ffffffff81af36a0>] x86_64_start_kernel+0xf1/0xf4
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
The driver was not bound checking the received length byte to ensure it was within the
the buffer size that is allocated for SMBus blocks. This resulted in buffer overflows
whenever an invalid length byte was received.
It also failed to ensure the length byte was not zero. If it received zero, it would end up
in an infinite loop as the at91_twi_read_next_byte function returned immediately without
allowing RHR to be read to clear the RXRDY interrupt.
Tested agaisnt a SMBus compliant battery.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
In rk3x SOC, the I2C controller can receive/transmit up to 32 bytes data
in one chunk, so the size of data to be write/read to/from TXDATAx/RXDATAx
must be less than or equal 32 bytes at a time.
Tested on rk3288-pinky board, elan receive 158 bytes data.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Acked-by: Max Schwarz <max.schwarz@online.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
There is a race condition in at91_do_twi_xfer when signals arrive.
If a signal is recieved while waiting for a transfer to complete
wait_for_completion_interruptible_timeout() will return -ERESTARTSYS.
This is not handled correctly resulting in interrupts still being
enabled and a transfer being in flight when we return.
Symptoms include a range of oopses and bus lockups. Oopses can happen
when the transfer completes because the interrupt handler will corrupt
the stack. If a new transfer is started before the interrupt fires
the controller will start a new transfer in the middle of the old one,
resulting in confused slaves and a locked bus.
To avoid this, use wait_for_completion_io_timeout instead so that we
don't have to deal with gracefully shutting down the transfer and
disabling the interrupts.
Signed-off-by: Simon Lindgren <simon@aqwary.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
The "clock-frequency" DT property is listed as optional, However,
the current code stores the return value of of_property_read_u32 in
the return code of mv64xxx_of_config, but then forgets to clear it
after setting the default value of "clock-frequency". It is then
passed out to the main probe function, resulting in a probe failure
when "clock-frequency" is missing.
This patch checks and then throws away the return value of
of_property_read_u32, instead of storing it and having to clear it
afterwards.
This issue was discovered after the property was removed from all
sunxi DTs.
Fixes: 4c730a06c19bb ("i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable@vger.kernel.org
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Sometimes the MNR and MST interrupts happen simultaneously (stop automatically
follows NACK, according to the manuals) and in such case the ID_NACK flag isn't
set since the MST interrupt handling precedes MNR and all interrupts are cleared
and disabled then, so that MNR interrupt is never noticed -- this causes NACK'ed
transfers to be falsely reported as successful. Exchanging MNR and MST handlers
fixes this issue, however the MNR bit somehow gets set again even after being
explicitly cleared, so I decided to completely suppress handling of all disabled
interrupts (which is a good thing anyway)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When intel_tv_detect() fails to do load detection it would forget to
drop the locks and clean up the acquire context. Fix it up.
This is a regression from:
commit 208bf9fdcd3575aa4a5d48b3e0295f7cdaf6fc44
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Aug 11 13:15:35 2014 +0300
drm/i915: Fix locking for intel_enable_pipe_a()
v2: Make the code more readable (Chris)
v3: Drop WARN_ON(type < 0) (Chris)
Cc: stable@vger.kernel.org
Cc: Tibor Billes <tbilles@gmx.com>
Reported-by: Tibor Billes <tbilles@gmx.com>
Tested-by: Tibor Billes <tbilles@gmx.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master
|
|
commit 0944fe3f4a32 ("s390/mm: implement software referenced bits")
triggered another paging/storage key corruption. There is an
unhandled invalid->valid pte change where we have to set the real
storage key from the pgste.
When doing paging a guest page might be swapcache or swap and when
faulted in it might be read-only and due to a parallel scan old.
An do_wp_page will make it writeable and young. Due to software
reference tracking this page was invalid and now becomes valid.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
|
|
Since 3.12 or more precisely commit 0944fe3f4a32 ("s390/mm:
implement software referenced bits") guest storage keys get
corrupted during paging. This commit added another valid->invalid
translation for page tables - namely ptep_test_and_clear_young.
We have to transfer the storage key into the pgste in that case.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
|
|
commit 39b2bbe3d715cf5013b5c48695ccdd25bd3bf120
"gpio: add flags argument to gpiod_get*() functions"
added a dynamic flags argument to all the GPIOD getter
functions, however this did not cover the stubs so
when people used gpiod stubs to compile out descriptor
code, compilation failed.
Solve this by:
- Also rename all the stub functions __gpiod_*
- Moving the vararg hack outside of #ifdef CONFIG_GPIOLIB
so these will always be available.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As the race condition on the inode cache, following scenario can appear:
[Thread a] [Thread b]
->f2fs_mkdir
->f2fs_add_link
->__f2fs_add_link
->init_inode_metadata failed here
->gc_thread_func
->f2fs_gc
->do_garbage_collect
->gc_data_segment
->f2fs_iget
->iget_locked
->wait_on_inode
->unlock_new_inode
->move_data_page
->make_bad_inode
->iput
When we fail in create/symlink/mkdir/mknod/tmpfile, the new allocated inode
should be set as bad to avoid being accessed by other thread. But in above
scenario, it allows f2fs to access the invalid inode before this inode was set
as bad.
This patch fix the potential problem, and this issue was found by code review.
change log from v1:
o Add condition judgment in gc_data_segment() suggested by Changman Lee.
o use iget_failed to simplify code.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
ALC1150 codec seems to need the COEF- and PLL-setups just like its
compatible ALC882 codec. Some machines (e.g. SunMicro X10SAT) show
the problem like too low output volumes unless the COEF setup is
applied.
Reported-and-tested-by: Dana Goyette <danagoyette@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
xfs_collapse_file_space() currently writes back the entire file
undergoing collapse range to settle things down for the extent shift
algorithm. While this prevents changes to the extent list during the
collapse operation, the writeback itself is not enough to prevent
unnecessary collapse failures.
The current shift algorithm uses the extent index to iterate the in-core
extent list. If a post-eof delalloc extent persists after the writeback
(e.g., a prior zero range op where the end of the range aligns with eof
can separate the post-eof blocks such that they are not written back and
converted), xfs_bmap_shift_extents() becomes confused over the encoded
br_startblock value and fails the collapse.
As with the full writeback, this is a temporary fix until the algorithm
is improved to cope with a volatile extent list and avoid attempts to
shift post-eof extents.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
If we have delalloc extents on a file before we run a collapse range
opertaion, we sync the range that we are going to collapse to
convert delalloc extents in that region to real extents to simplify
the shift operation.
However, the shift operation then assumes that the extent list is
not going to change as it iterates over the extent list moving
things about. Unfortunately, this isn't true because we can't hold
the ILOCK over all the operations. We can prevent new IO from
modifying the extent list by holding the IOLOCK, but that doesn't
prevent writeback from running....
And when writeback runs, it can convert delalloc extents is the
range of the file prior to the region being collapsed, and this
changes the indexes of all the extents in the file. That causes the
collapse range operation to Go Bad.
The right fix is to rewrite the extent shift operation not to be
dependent on the extent list not changing across the entire
operation, but this is a fairly significant piece of work to do.
Hence, as a short-term workaround for the problem, sync the entire
file before starting a collapse operation to remove all delalloc
ranges from the file and so avoid the problem of concurrent
writeback changing the extent list.
Diagnosed-and-Reported-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
The file collapse mechanism uses xfs_bmap_shift_extents() to collapse
all subsequent extents down into the specified, previously punched out,
region. This function performs some validation, such as whether a
sufficient hole exists in the target region of the collapse, then shifts
the remaining exents downward.
The exit path of the function currently logs the inode unconditionally.
While we must log the inode (and abort) if an error occurs and the
transaction is dirty, the initial validation paths can generate errors
before the transaction has been dirtied. This creates an unnecessary
filesystem shutdown scenario, as the caller will cancel a transaction
that has been marked dirty.
Modify xfs_bmap_shift_extents() to OR the logflags bits as modifications
are made to the inode bmap. Only log the inode in the exit path if
logflags has been set. This ensures we only have to cancel a dirty
transaction if modifications have been made and prevents an unnecessary
filesystem shutdown otherwise.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
Now we are not doing silly things with dirtying buffers beyond EOF
and using invalidation correctly, we can finally reduce the ranges of
writeback and invalidation used by direct IO to match that of the IO
being issued.
Bring the writeback and invalidation ranges back to match the
generic direct IO code - this will greatly reduce the perturbation
of cached data when direct IO and buffered IO are mixed, but still
provide the same buffered vs direct IO coherency behaviour we
currently have.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
