| Age | Commit message (Collapse) | Author |
|---|
|
Accidentally spotted while trying to understand what else needs
to be renamed to netif_ prefix. Most of the calls to dev_set_promiscuity
are adjacent to dev_set_allmulti or dev_disable_lro so it should
be safe to add the lock. Note that new netif_set_promiscuity is
currently unused, the locked paths call __dev_set_promiscuity directly.
Fixes: ad7c7b2172c3 ("net: hold netdev instance lock during sysfs operations")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250506011919.2882313-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When compressed data deduplication is enabled, multiple logical extents
may reference the same compressed physical cluster.
The previous commit 94c43de73521 ("erofs: fix wrong primary bvec
selection on deduplicated extents") already avoids using shortened
bvecs. However, in such cases, the extra temporary buffers also
need to be preserved for later use in z_erofs_fill_other_copies() to
to prevent data corruption.
IOWs, extra temporary buffers have to be retained not only due to
varying start relative offsets (`pageofs_out`, as indicated by
`pcl->multibases`) but also because of shortened bvecs.
android.hardware.graphics.composer@2.1.so : 270696 bytes
0: 0.. 204185 | 204185 : 628019200.. 628084736 | 65536
-> 1: 204185.. 225536 | 21351 : 544063488.. 544129024 | 65536
2: 225536.. 270696 | 45160 : 0.. 0 | 0
com.android.vndk.v28.apex : 93814897 bytes
...
364: 53869896..54095257 | 225361 : 543997952.. 544063488 | 65536
-> 365: 54095257..54309344 | 214087 : 544063488.. 544129024 | 65536
366: 54309344..54514557 | 205213 : 544129024.. 544194560 | 65536
...
Both 204185 and 54095257 have the same start relative offset of 3481,
but the logical page 55 of `android.hardware.graphics.composer@2.1.so`
ranges from 225280 to 229632, forming a shortened bvec [225280, 225536)
that cannot be used for decompressing the range from 54095257 to
54309344 of `com.android.vndk.v28.apex`.
Since `pcl->multibases` is already meaningless, just mark `be->keepxcpy`
on demand for simplicity.
Again, this issue can only lead to data corruption if `-Ededupe` is on.
Fixes: 94c43de73521 ("erofs: fix wrong primary bvec selection on deduplicated extents")
Reviewed-by: Hongbo Li <lihongbo22@huawei.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250506101850.191506-1-hsiangkao@linux.alibaba.com
|
|
__qdisc_destroy() calls into various qdiscs .destroy() op, which in turn
can call .ndo_setup_tc(), which requires the netdev instance lock.
This commit extends the critical section in
unregister_netdevice_many_notify() to cover dev_shutdown() (and
dev_tcx_uninstall() as a side-effect) and acquires the netdev instance
lock in __dev_change_net_namespace() for the other dev_shutdown() call.
This should now guarantee that for all qdisc ops, the netdev instance
lock is held during .ndo_setup_tc().
Fixes: a0527ee2df3f ("net: hold netdev instance lock during qdisc ndo_setup_tc")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250505194713.1723399-1-cratiu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use Device Serial Number instead of PCI bus/device/function for
the index of struct ice_adapter.
Functions on the same physical device should point to the very same
ice_adapter instance, but with two PFs, when at least one of them is
PCI-e passed-through to a VM, it is no longer the case - PFs will get
seemingly random PCI BDF values, and thus indices, what finally leds to
each of them being on their own instance of ice_adapter. That causes them
to don't attempt any synchronization of the PTP HW clock usage, or any
other future resources.
DSN works nicely in place of the index, as it is "immutable" in terms of
virtualization.
Fixes: 0e2bddf9e5f9 ("ice: add ice_adapter for shared data across PFs on the same NIC")
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250505161939.2083581-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For now, we need another entry for these devices, this
will be changed completely for 6.16.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219926
Link: https://patch.msgid.link/20250506214258.2efbdc9e9a82.I31915ec252bd1c74bd53b89a0e214e42a74b6f2e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The status code should be type of __le16.
Fixes: 83e897a961b8 ("wifi: ieee80211: add definitions for negotiated TID to Link map")
Fixes: 8f500fbc6c65 ("wifi: mac80211: process and save negotiated TID to Link mapping request")
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Link: https://patch.msgid.link/20250505081946.3927214-1-michael-cy.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
defragmentation
Currently during the multi-link element defragmentation process, the
multi-link element length added to the total IEs length when calculating
the length of remaining IEs after the multi-link element in
cfg80211_defrag_mle(). This could lead to out-of-bounds access if the
multi-link element or its corresponding fragment elements are the last
elements in the IEs buffer.
To address this issue, correctly calculate the remaining IEs length by
deducting the multi-link element end offset from total IEs end offset.
Cc: stable@vger.kernel.org
Fixes: 2481b5da9c6b ("wifi: cfg80211: handle BSS data contained in ML probe responses")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://patch.msgid.link/20250424-fix_mle_defragmentation_oob_access-v1-1-84412a1743fa@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The vfio-pci huge_fault handler doesn't make any attempt to insert a
mapping containing the faulting address, it only inserts mappings if the
faulting address and resulting pfn are aligned. This works in a lot of
cases, particularly in conjunction with QEMU where DMA mappings linearly
fault the mmap. However, there are configurations where we don't get
that linear faulting and pages are faulted on-demand.
The scenario reported in the bug below is such a case, where the physical
address width of the CPU is greater than that of the IOMMU, resulting in a
VM where guest firmware has mapped device MMIO beyond the address width of
the IOMMU. In this configuration, the MMIO is faulted on demand and
tracing indicates that occasionally the faults generate a VM_FAULT_OOM.
Given the use case, this results in a "error: kvm run failed Bad address",
killing the VM.
The host is not under memory pressure in this test, therefore it's
suspected that VM_FAULT_OOM is actually the result of a NULL return from
__pte_offset_map_lock() in the get_locked_pte() path from insert_pfn().
This suggests a potential race inserting a pte concurrent to a pmd, and
maybe indicates some deficiency in the mm layer properly handling such a
case.
Nevertheless, Peter noted the inconsistency of vfio-pci's huge_fault
handler where our mapping granularity depends on the alignment of the
faulting address relative to the order rather than aligning the faulting
address to the order to more consistently insert huge mappings. This
change not only uses the page tables more consistently and efficiently, but
as any fault to an aligned page results in the same mapping, the race
condition suspected in the VM_FAULT_OOM is avoided.
Reported-by: Adolfo <adolfotregosa@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220057
Fixes: 09dfc8a5f2ce ("vfio/pci: Fallback huge faults for unaligned pfn")
Cc: stable@vger.kernel.org
Tested-by: Adolfo <adolfotregosa@gmail.com>
Co-developed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/20250502224035.3183451-1-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- revert device path canonicalization, this does not work as intended
with namespaces and is not reliable in all setups
- fix crash in scrub when checksum tree is not valid, e.g. when mounted
with rescue=ignoredatacsums
- fix crash when tracepoint btrfs_prelim_ref_insert is enabled
- other minor fixups:
- open code folio_index(), meant to be used in MM code
- use matching type for sizeof in compression allocation
* tag 'for-6.15-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: open code folio_index() in btree_clear_folio_dirty_tag()
Revert "btrfs: canonicalize the device path before adding it"
btrfs: avoid NULL pointer dereference if no valid csum tree
btrfs: handle empty eb->folios in num_extent_folios()
btrfs: correct the order of prelim_ref arguments in btrfs__prelim_ref
btrfs: compression: adjust cb->compressed_folios allocation type
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mikulas Patocka:
- fix reading past the end of allocated memory
- fix missing dm_put_live_table() in dm_keyslot_evict()
* tag 'for-6.15/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix copying after src array boundaries
dm: add missing unlock on in dm_keyslot_evict()
|
|
As reported by Sebastian Andrzej Siewior the use of local_bh_disable()
is only feasible in uni processor systems to update the modification rules.
The usual use-case to update the modification rules is to update the data
of the modifications but not the modification types (AND/OR/XOR/SET) or
the checksum functions itself.
To omit additional memory allocations to maintain fast modification
switching times, the modification description space is doubled at gw-job
creation time so that only the reference to the active modification
description is changed under rcu protection.
Rename cgw_job::mod to cf_mod and make it a RCU pointer. Allocate in
cgw_create_job() and free it together with cgw_job in
cgw_job_free_rcu(). Update all users to dereference cgw_job::cf_mod with
a RCU accessor and if possible once.
[bigeasy: Replace mod1/mod2 from the Oliver's original patch with dynamic
allocation, use RCU annotation and accessor]
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Closes: https://lore.kernel.org/linux-can/20231031112349.y0aLoBrz@linutronix.de/
Fixes: dd895d7f21b2 ("can: cangw: introduce optional uid to reference created routing jobs")
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/20250429070555.cs-7b_eZ@linutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Marc Kleine-Budde <mkl@pengutronix.de> says:
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
With the mcp251xfd driver the removal of the module causes the
following warning:
| WARNING: CPU: 0 PID: 352 at net/core/dev.c:7342 __netif_napi_del_locked+0xc8/0xd8
as can_rx_offload_del() deletes the NAPI, while it is still active,
because the interface is still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
All other driver using the rx-offload helper have been checked and the
same issue has been found in the rockchip and m_can driver. These have
been fixed, but only compile time tested. On the mcp251xfd the fix was
tested on hardware.
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-0-59a9b131589d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 1be37d3b0414 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-3-59a9b131589d@pengutronix.de
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: ff60bfbaf67f ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-2-59a9b131589d@pengutronix.de
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
With the mcp251xfd driver the removal of the module causes the
following warning:
| WARNING: CPU: 0 PID: 352 at net/core/dev.c:7342 __netif_napi_del_locked+0xc8/0xd8
as can_rx_offload_del() deletes the NAPI, while it is still active,
because the interface is still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-1-59a9b131589d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The TDC is currently hardcoded enabled. This means that even for lower
CAN-FD data bitrates (with a DBRP (data bitrate prescaler) > 2) a TDC
is configured. This leads to a bus-off condition.
ISO 11898-1 section 11.3.3 says "Transmitter delay compensation" (TDC)
is only applicable if DBRP is 1 or 2.
To fix the problem, switch the driver to use the TDC calculation
provided by the CAN driver framework (which respects ISO 11898-1
section 11.3.3). This has the positive side effect that userspace can
control TDC as needed.
Demonstration of the feature in action:
| $ ip link set can0 up type can bitrate 125000 dbitrate 500000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 125000 sample-point 0.875
| tq 50 prop-seg 69 phase-seg1 70 phase-seg2 20 sjw 10 brp 2
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 500000 dsample-point 0.875
| dtq 125 dprop-seg 6 dphase-seg1 7 dphase-seg2 2 dsjw 1 dbrp 5
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
| $ ip link set can0 up type can bitrate 1000000 dbitrate 4000000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD,TDC-AUTO> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 1000000 sample-point 0.750
| tq 25 prop-seg 14 phase-seg1 15 phase-seg2 10 sjw 5 brp 1
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 4000000 dsample-point 0.700
| dtq 25 dprop-seg 3 dphase-seg1 3 dphase-seg2 3 dsjw 1 dbrp 1
| tdco 7
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
There has been some confusion about the MCP2518FD using a relative or
absolute TDCO due to the datasheet specifying a range of [-64,63]. I
have a custom board with a 40 MHz clock and an estimated loop delay of
100 to 216 ns. During testing at a data bit rate of 4 Mbit/s I found
that using can_get_relative_tdco() resulted in bus-off errors. The
final TDCO value was 1 which corresponds to a 10% SSP in an absolute
configuration. This behavior is expected if the TDCO value is really
absolute and not relative. Using priv->can.tdc.tdco instead results in
a final TDCO of 8, setting the SSP at exactly 80%. This configuration
works.
The automatic, manual, and off TDC modes were tested at speeds up to,
and including, 8 Mbit/s on real hardware and behave as expected.
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reported-by: Kelsey Maes <kelsey@vpprocess.com>
Closes: https://lore.kernel.org/all/C2121586-C87F-4B23-A933-845362C29CA1@vpprocess.com
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Kelsey Maes <kelsey@vpprocess.com>
Link: https://patch.msgid.link/20250430161501.79370-1-kelsey@vpprocess.com
[mkl: add comment]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The spin lock tx_handling_spinlock in struct m_can_classdev is not
being initialized. This leads the following spinlock bad magic
complaint from the kernel, eg. when trying to send CAN frames with
cansend from can-utils:
| BUG: spinlock bad magic on CPU#0, cansend/95
| lock: 0xff60000002ec1010, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
| CPU: 0 UID: 0 PID: 95 Comm: cansend Not tainted 6.15.0-rc3-00032-ga79be02bba5c #5 NONE
| Hardware name: MachineWare SIM-V (DT)
| Call Trace:
| [<ffffffff800133e0>] dump_backtrace+0x1c/0x24
| [<ffffffff800022f2>] show_stack+0x28/0x34
| [<ffffffff8000de3e>] dump_stack_lvl+0x4a/0x68
| [<ffffffff8000de70>] dump_stack+0x14/0x1c
| [<ffffffff80003134>] spin_dump+0x62/0x6e
| [<ffffffff800883ba>] do_raw_spin_lock+0xd0/0x142
| [<ffffffff807a6fcc>] _raw_spin_lock_irqsave+0x20/0x2c
| [<ffffffff80536dba>] m_can_start_xmit+0x90/0x34a
| [<ffffffff806148b0>] dev_hard_start_xmit+0xa6/0xee
| [<ffffffff8065b730>] sch_direct_xmit+0x114/0x292
| [<ffffffff80614e2a>] __dev_queue_xmit+0x3b0/0xaa8
| [<ffffffff8073b8fa>] can_send+0xc6/0x242
| [<ffffffff8073d1c0>] raw_sendmsg+0x1a8/0x36c
| [<ffffffff805ebf06>] sock_write_iter+0x9a/0xee
| [<ffffffff801d06ea>] vfs_write+0x184/0x3a6
| [<ffffffff801d0a88>] ksys_write+0xa0/0xc0
| [<ffffffff801d0abc>] __riscv_sys_write+0x14/0x1c
| [<ffffffff8079ebf8>] do_trap_ecall_u+0x168/0x212
| [<ffffffff807a830a>] handle_exception+0x146/0x152
Initializing the spin lock in m_can_class_allocate_dev solves that
problem.
Fixes: 1fa80e23c150 ("can: m_can: Introduce a tx_fifo_in_flight counter")
Signed-off-by: Antonios Salios <antonios@mwa.re>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250425111744.37604-2-antonios@mwa.re
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
A use-after-free is possible if one thread destroys the file
via __ksmbd_close_fd while another thread holds a reference to
it. The existing checks on fp->refcount are not sufficient to
prevent this.
The fix takes ft->lock around the section which removes the
file from the file table. This prevents two threads acquiring the
same file pointer via __close_file_table_ids, as well as the other
functions which retrieve a file from the IDR and which already use
this same lock.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Heelan <seanheelan@gmail.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
ksmbd_vfs_stream_write() did not validate whether the write offset
(*pos) was within the bounds of the existing stream data length (v_len).
If *pos was greater than or equal to v_len, this could lead to an
out-of-bounds memory write.
This patch adds a check to ensure *pos is less than v_len before
proceeding. If the condition fails, -EINVAL is returned.
Cc: stable@vger.kernel.org
Signed-off-by: Norbert Szetei <norbert@doyensec.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
The blammed commit copied to argv the size of the reallocated argv,
instead of the size of the old_argv, thus reading and copying from
past the old_argv allocated memory.
Following BUG_ON was hit:
[ 3.038929][ T1] kernel BUG at lib/string_helpers.c:1040!
[ 3.039147][ T1] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
...
[ 3.056489][ T1] Call trace:
[ 3.056591][ T1] __fortify_panic+0x10/0x18 (P)
[ 3.056773][ T1] dm_split_args+0x20c/0x210
[ 3.056942][ T1] dm_table_add_target+0x13c/0x360
[ 3.057132][ T1] table_load+0x110/0x3ac
[ 3.057292][ T1] dm_ctl_ioctl+0x424/0x56c
[ 3.057457][ T1] __arm64_sys_ioctl+0xa8/0xec
[ 3.057634][ T1] invoke_syscall+0x58/0x10c
[ 3.057804][ T1] el0_svc_common+0xa8/0xdc
[ 3.057970][ T1] do_el0_svc+0x1c/0x28
[ 3.058123][ T1] el0_svc+0x50/0xac
[ 3.058266][ T1] el0t_64_sync_handler+0x60/0xc4
[ 3.058452][ T1] el0t_64_sync+0x1b0/0x1b4
[ 3.058620][ T1] Code: f800865e a9bf7bfd 910003fd 941f48aa (d4210000)
[ 3.058897][ T1] ---[ end trace 0000000000000000 ]---
[ 3.059083][ T1] Kernel panic - not syncing: Oops - BUG: Fatal exception
Fix it by copying the size of src, and not the size of dst, as it was.
Fixes: 5a2a6c428190 ("dm: always update the array size in realloc_argv on success")
Cc: stable@vger.kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
Remove redundant PSE reset.
When setting FE register there is no need to reset PSE,
doing so may cause FE to work abnormal.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/3a5223473e086a4b54a2b9a44df7d9ddcc2bc75a
Fixes: dee4dd10c79aa ("net: ethernet: mtk_eth_soc: ppe: add support for multiple PPEs")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://patch.msgid.link/18f0ac7d83f82defa3342c11ef0d1362f6b81e88.1746406763.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The purpose of resetting the TX queue is to reset the byte and packet
count as well as to clear the software flow control XOFF bit.
MediaTek developers pointed out that netdev_reset_queue would only
resets queue 0 of the network device.
Queues that are not reset may cause unexpected issues.
Packets may stop being sent after reset and "transmit timeout" log may
be displayed.
Import fix from MediaTek's SDK to resolve this issue.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/319c0d9905579a46dc448579f892f364f1f84818
Fixes: f63959c7eec31 ("net: ethernet: mtk_eth_soc: implement multi-queue support for per-port queues")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/c9ff9adceac4f152239a0f65c397f13547639175.1746406763.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Strings from the kernel are guaranteed to be null terminated and
ynl_attr_validate() checks for this. But it doesn't check if the string
has a len of 0, which would cause problems when trying to access
data[len - 1]. Fix this by checking that len is positive.
Signed-off-by: David Wei <dw@davidwei.uk>
Link: https://patch.msgid.link/20250503043050.861238-1-dw@davidwei.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Mohsin Bashir says:
====================
selftests: drv: net: fix `ping.py` test failure
Fix `ping.py` test failure on an ipv6 system, and appropriately handle the
cases where either one of the two address families (ipv4, ipv6) is not
present.
====================
Link: https://patch.msgid.link/20250503013518.1722913-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the test result does not differentiate between the cases when
either one of the address families are configured or if both the address
families are configured. Ideally, the result should report if a
particular case was skipped.
./drivers/net/ping.py
TAP version 13
1..7
ok 1 ping.test_default_v4 # SKIP Test requires IPv4 connectivity
ok 2 ping.test_default_v6
ok 3 ping.test_xdp_generic_sb
ok 4 ping.test_xdp_generic_mb
ok 5 ping.test_xdp_native_sb
ok 6 ping.test_xdp_native_mb
ok 7 ping.test_xdp_offload # SKIP device does not support offloaded XDP
Totals: pass:5 fail:0 xfail:0 xpass:0 skip:2 error:0
Fixes: 75cc19c8ff89 ("selftests: drv-net: add xdp cases for ping.py")
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Reviewed-by: David Wei <dw@davidwei.uk>
Link: https://patch.msgid.link/20250503013518.1722913-4-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On a system with either of the ipv4 or ipv6 information missing, tests
are currently skipped. Ideally, the test should run as long as at least
one address family is present. This patch make test run whenever
possible.
Before:
./drivers/net/ping.py
TAP version 13
1..6
ok 1 ping.test_default # SKIP Test requires IPv4 connectivity
ok 2 ping.test_xdp_generic_sb # SKIP Test requires IPv4 connectivity
ok 3 ping.test_xdp_generic_mb # SKIP Test requires IPv4 connectivity
ok 4 ping.test_xdp_native_sb # SKIP Test requires IPv4 connectivity
ok 5 ping.test_xdp_native_mb # SKIP Test requires IPv4 connectivity
ok 6 ping.test_xdp_offload # SKIP device does not support offloaded XDP
Totals: pass:0 fail:0 xfail:0 xpass:0 skip:6 error:0
After:
./drivers/net/ping.py
TAP version 13
1..6
ok 1 ping.test_default
ok 2 ping.test_xdp_generic_sb
ok 3 ping.test_xdp_generic_mb
ok 4 ping.test_xdp_native_sb
ok 5 ping.test_xdp_native_mb
ok 6 ping.test_xdp_offload # SKIP device does not support offloaded XDP
Totals: pass:5 fail:0 xfail:0 xpass:0 skip:1 error:0
Fixes: 75cc19c8ff89 ("selftests: drv-net: add xdp cases for ping.py")
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Link: https://patch.msgid.link/20250503013518.1722913-3-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The `get_interface_info` call has ip version hard-coded which leads to
failures on an IPV6 system. The NetDrvEnv class already gathers
information about remote interface, so instead of fixing the local
implementation switch to using cfg.remote_ifname.
Before:
./drivers/net/ping.py
Traceback (most recent call last):
File "/new_tests/./drivers/net/ping.py", line 217, in <module>
main()
File "/new_tests/./drivers/net/ping.py", line 204, in main
get_interface_info(cfg)
File "/new_tests/./drivers/net/ping.py", line 128, in get_interface_info
raise KsftFailEx('Can not get remote interface')
net.lib.py.ksft.KsftFailEx: Can not get remote interface
After:
./drivers/net/ping.py
TAP version 13
1..6
ok 1 ping.test_default # SKIP Test requires IPv4 connectivity
ok 2 ping.test_xdp_generic_sb # SKIP Test requires IPv4 connectivity
ok 3 ping.test_xdp_generic_mb # SKIP Test requires IPv4 connectivity
ok 4 ping.test_xdp_native_sb # SKIP Test requires IPv4 connectivity
ok 5 ping.test_xdp_native_mb # SKIP Test requires IPv4 connectivity
ok 6 ping.test_xdp_offload # SKIP device does not support offloaded XDP
Totals: pass:0 fail:0 xfail:0 xpass:0 skip:6 error:0
Fixes: 75cc19c8ff89 ("selftests: drv-net: add xdp cases for ping.py")
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Reviewed-by: David Wei <dw@davidwei.uk>
Link: https://patch.msgid.link/20250503013518.1722913-2-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Guillaume Nault says:
====================
gre: Reapply IPv6 link-local address generation fix.
Reintroduce the IPv6 link-local address generation fix for GRE and its
kernel selftest. These patches were introduced by merge commit
b3fc5927de4b ("Merge branch
'gre-fix-regressions-in-ipv6-link-local-address-generation'") but have
been reverted by commit 8417db0be5bb ("Merge branch
'gre-revert-ipv6-link-local-address-fix'"), because it uncovered
another bug in multipath routing. Now that this bug has been
investigated and fixed, we can apply the GRE link-local address fix
and its kernel selftest again.
For convenience, here's the original cover letter:
IPv6 link-local address generation has some special cases for GRE
devices. This has led to several regressions in the past, and some of
them are still not fixed. This series fixes the remaining problems,
like the ipv6.conf.<dev>.addr_gen_mode sysctl being ignored and the
router discovery process not being started (see details in patch 1).
To avoid any further regressions, patch 2 adds selftests covering
IPv4 and IPv6 gre/gretap devices with all combinations of currently
supported addr_gen_mode values.
====================
Link: https://patch.msgid.link/cover.1746225213.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
GRE devices have their special code for IPv6 link-local address
generation that has been the source of several regressions in the past.
Add selftest to check that all gre, ip6gre, gretap and ip6gretap get an
IPv6 link-link local address in accordance with the
net.ipv6.conf.<dev>.addr_gen_mode sysctl.
Note: This patch was originally applied as commit 6f50175ccad4 ("selftests:
Add IPv6 link-local address generation tests for GRE devices.").
However, it was then reverted by commit 355d940f4d5a ("Revert "selftests:
Add IPv6 link-local address generation tests for GRE devices."")
because the commit it depended on was going to be reverted. Now that
the situation is resolved, we can add this selftest again (no changes
since original patch, appart from context update in
tools/testing/selftests/net/Makefile).
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/2c3a5733cb3a6e3119504361a9b9f89fda570a2d.1746225214.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use addrconf_addr_gen() to generate IPv6 link-local addresses on GRE
devices in most cases and fall back to using add_v4_addrs() only in
case the GRE configuration is incompatible with addrconf_addr_gen().
GRE used to use addrconf_addr_gen() until commit e5dd729460ca ("ip/ip6_gre:
use the same logic as SIT interfaces when computing v6LL address")
restricted this use to gretap and ip6gretap devices, and created
add_v4_addrs() (borrowed from SIT) for non-Ethernet GRE ones.
The original problem came when commit 9af28511be10 ("addrconf: refuse
isatap eui64 for INADDR_ANY") made __ipv6_isatap_ifid() fail when its
addr parameter was 0. The commit says that this would create an invalid
address, however, I couldn't find any RFC saying that the generated
interface identifier would be wrong. Anyway, since gre over IPv4
devices pass their local tunnel address to __ipv6_isatap_ifid(), that
commit broke their IPv6 link-local address generation when the local
address was unspecified.
Then commit e5dd729460ca ("ip/ip6_gre: use the same logic as SIT
interfaces when computing v6LL address") tried to fix that case by
defining add_v4_addrs() and calling it to generate the IPv6 link-local
address instead of using addrconf_addr_gen() (apart for gretap and
ip6gretap devices, which would still use the regular
addrconf_addr_gen(), since they have a MAC address).
That broke several use cases because add_v4_addrs() isn't properly
integrated into the rest of IPv6 Neighbor Discovery code. Several of
these shortcomings have been fixed over time, but add_v4_addrs()
remains broken on several aspects. In particular, it doesn't send any
Router Sollicitations, so the SLAAC process doesn't start until the
interface receives a Router Advertisement. Also, add_v4_addrs() mostly
ignores the address generation mode of the interface
(/proc/sys/net/ipv6/conf/*/addr_gen_mode), thus breaking the
IN6_ADDR_GEN_MODE_RANDOM and IN6_ADDR_GEN_MODE_STABLE_PRIVACY cases.
Fix the situation by using add_v4_addrs() only in the specific scenario
where the normal method would fail. That is, for interfaces that have
all of the following characteristics:
* run over IPv4,
* transport IP packets directly, not Ethernet (that is, not gretap
interfaces),
* tunnel endpoint is INADDR_ANY (that is, 0),
* device address generation mode is EUI64.
In all other cases, revert back to the regular addrconf_addr_gen().
Also, remove the special case for ip6gre interfaces in add_v4_addrs(),
since ip6gre devices now always use addrconf_addr_gen() instead.
Note:
This patch was originally applied as commit 183185a18ff9 ("gre: Fix
IPv6 link-local address generation."). However, it was then reverted
by commit fc486c2d060f ("Revert "gre: Fix IPv6 link-local address
generation."") because it uncovered another bug that ended up
breaking net/forwarding/ip6gre_custom_multipath_hash.sh. That other
bug has now been fixed by commit 4d0ab3a6885e ("ipv6: Start path
selection from the first nexthop"). Therefore we can now revive this
GRE patch (no changes since original commit 183185a18ff9 ("gre: Fix
IPv6 link-local address generation.").
Fixes: e5dd729460ca ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/a88cc5c4811af36007645d610c95102dccb360a6.1746225214.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Device Tree and Ethernet MAC driver writers often misunderstand RGMII
delays. Rewrite the Normative section in terms of the PCB, is the PCB
adding the 2ns delay. This meaning was previous implied by the
definition, but often wrongly interpreted due to the ambiguous wording
and looking at the definition from the wrong perspective. The new
definition concentrates clearly on the hardware, and should be less
ambiguous.
Add an Informative section to the end of the binding describing in
detail what the four RGMII delays mean. This expands on just the PCB
meaning, adding in the implications for the MAC and PHY.
Additionally, when the MAC or PHY needs to add a delay, which is
software configuration, describe how Linux does this, in the hope of
reducing errors. Make it clear other users of device tree binding may
implement the software configuration in other ways while still
conforming to the binding.
Fixes: 9d3de3c58347 ("dt-bindings: net: Add YAML schemas for the generic Ethernet options")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20250430-v6-15-rc3-net-rgmii-delays-v2-1-099ae651d5e5@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The selftests added to our CI by Bui Quang Minh recently reveals
that there is a mem leak on the error path of virtnet_xsk_pool_enable():
unreferenced object 0xffff88800a68a000 (size 2048):
comm "xdp_helper", pid 318, jiffies 4294692778
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 0):
__kvmalloc_node_noprof+0x402/0x570
virtnet_xsk_pool_enable+0x293/0x6a0 (drivers/net/virtio_net.c:5882)
xp_assign_dev+0x369/0x670 (net/xdp/xsk_buff_pool.c:226)
xsk_bind+0x6a5/0x1ae0
__sys_bind+0x15e/0x230
__x64_sys_bind+0x72/0xb0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Acked-by: Jason Wang <jasowang@redhat.com>
Fixes: e9f3962441c0 ("virtio_net: xsk: rx: support fill with xsk buffer")
Link: https://patch.msgid.link/20250430163836.3029761-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 4bc12818b363 ("virtio-net: disable delayed refill when pausing rx")
fixed a deadlock between reconfig paths and refill work trying to disable
the same NAPI instance. The refill work can't run in parallel with reconfig
because trying to double-disable a NAPI instance causes a stall under the
instance lock, which the reconfig path needs to re-enable the NAPI and
therefore unblock the stalled thread.
There are two cases where we re-enable refill too early. One is in the
virtnet_set_queues() handler. We call it when installing XDP:
virtnet_rx_pause_all(vi);
...
virtnet_napi_tx_disable(..);
...
virtnet_set_queues(..);
...
virtnet_rx_resume_all(..);
We want the work to be disabled until we call virtnet_rx_resume_all(),
but virtnet_set_queues() kicks it before NAPIs were re-enabled.
The other case is a more trivial case of mis-ordering in
__virtnet_rx_resume() found by code inspection.
Taking the spin lock in virtnet_set_queues() (requested during review)
may be unnecessary as we are under rtnl_lock and so are all paths writing
to ->refill_enabled.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Bui Quang Minh <minhquangbui99@gmail.com>
Fixes: 4bc12818b363 ("virtio-net: disable delayed refill when pausing rx")
Fixes: 413f0271f396 ("net: protect NAPI enablement with netdev_lock()")
Link: https://patch.msgid.link/20250430163758.3029367-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cong Wang says:
====================
net_sched: fix a regression in sch_htb
This patchset contains a fix for the regression reported by Alan and a
selftest to cover that case. Please see each patch description for more
details.
====================
Link: https://patch.msgid.link/20250428232955.1740419-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Integrate the reproducer from Alan into TC selftests and use scapy to
generate TCP traffic instead of relying on ping command.
Cc: Alan J. Wylie <alan@wylie.me.uk>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://patch.msgid.link/20250428232955.1740419-3-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Alan reported a NULL pointer dereference in htb_next_rb_node()
after we made htb_qlen_notify() idempotent.
It turns out in the following case it introduced some regression:
htb_dequeue_tree():
|-> fq_codel_dequeue()
|-> qdisc_tree_reduce_backlog()
|-> htb_qlen_notify()
|-> htb_deactivate()
|-> htb_next_rb_node()
|-> htb_deactivate()
For htb_next_rb_node(), after calling the 1st htb_deactivate(), the
clprio[prio]->ptr could be already set to NULL, which means
htb_next_rb_node() is vulnerable here.
For htb_deactivate(), although we checked qlen before calling it, in
case of qlen==0 after qdisc_tree_reduce_backlog(), we may call it again
which triggers the warning inside.
To fix the issues here, we need to:
1) Make htb_deactivate() idempotent, that is, simply return if we
already call it before.
2) Make htb_next_rb_node() safe against ptr==NULL.
Many thanks to Alan for testing and for the reproducer.
Fixes: 5ba8b837b522 ("sch_htb: make htb_qlen_notify() idempotent")
Reported-by: Alan J. Wylie <alan@wylie.me.uk>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://patch.msgid.link/20250428232955.1740419-2-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts
1fdbe0b184c8 bcachefs: Make sure c->vfs_sb is set before starting fs
switched up bch2_fs_get_tree() so that we got a superblock before
calling bch2_fs_start, so that c->vfs_sb would always be initialized
while the filesystem was active.
This turned out not to be necessary, because blk_holder_ops were
implemented using our own locking, not vfs locking.
And this had the side effect of creating a super_block and doing our
full recovery (including potentially fsck) before setting SB_BORN, which
causes things like sync calls to hang until our recovery is finished.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
wake_up() doesn't require a barrier - but wake_up_bit() does.
This only affected non x86, and primarily lead to lost wakeups after
btree node reads.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
There was a buggy version of bcachefs-tools which picked misaligned
bucket sizes when formatting, and we're also about to do dynamic block
sizes - which will allow picking logical block size or physical block
size of the device per-write, allowing for better compression ratios at
the cost of slightly worse write performance (i.e. forcing the device to
do RMW or extra buffering).
To account for this, tweak bch2_alloc_sectors_start() to properly align
open_buckets to the blocksize of the write we're about to do.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
If promote target isn't set, rebalance should still leave a cached copy
on the faster device.
Fall back to foreground_target if it's set, or allow a cached copy on
any device if neither are set.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux
Pull uml fix from Johannes Berg:
"There's just a single fix here for the _nofault changes that were
causing issues with clang, and then when we looked at it some other
issues seemed to exist"
* tag 'uml-for-linux-6.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux:
um: fix _nofault accesses
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"The main changes are once more for the NXP i.MX platform, addressing
multiple regressions in recent devicetree updates for the i.MX8MM and
i.MX6ULL SoCs, a PCIe fix for i.MX9 and a MAINTAINERS file update to
disambiguate NXP i.MX SoCs from Sony IMX image sensors.
The stm32 platform devicetree files get some compatibility fixes for
the interrupt controller node.
Another compatibility fix is done for the Arm Morello platform's cache
controller node.
The code changes are all for firmware drivers, fixing kernel-side bugs
on the Arm FF-A and SCMI drivers"
* tag 'soc-fixes-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: st: Use 128kB size for aliased GIC400 register access on stm32mp23 SoCs
arm64: dts: st: Adjust interrupt-controller for stm32mp23 SoCs
arm64: dts: st: Use 128kB size for aliased GIC400 register access on stm32mp21 SoCs
arm64: dts: st: Adjust interrupt-controller for stm32mp21 SoCs
arm64: dts: st: Use 128kB size for aliased GIC400 register access on stm32mp25 SoCs
arm64: dts: st: Adjust interrupt-controller for stm32mp25 SoCs
arm64: dts: imx8mm-verdin: Link reg_usdhc2_vqmmc to usdhc2
MAINTAINERS: add exclude for dt-bindings to imx entry
ARM: dts: opos6ul: add ksz8081 phy properties
arm64: dts: imx95: Correct the range of PCIe app-reg region
arm64: dts: imx8mp: configure GPU and NPU clocks in nominal DTSI
arm64: dts: morello: Fix-up cache nodes
firmware: arm_ffa: Skip Rx buffer ownership release if not acquired
firmware: arm_scmi: Fix timeout checks on polling path
firmware: arm_scmi: Balance device refcount when destroying devices
|
|
Just the regular update of all defconfigs.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
After commit 653d7825c149 ("dcssblk: mark DAX broken, remove FS_DAX_LIMITED
support") moved the "select DAX" from config DCSSBLK to the new config
DCSSBLK_DAX, randconfig tests could result in build errors like this:
s390-linux-ld: drivers/s390/block/dcssblk.o: in function `dcssblk_shared_store':
drivers/s390/block/dcssblk.c:417: undefined reference to `kill_dax'
s390-linux-ld: drivers/s390/block/dcssblk.c:418: undefined reference to `put_dax'
This is because it's now possible to have CONFIG_DCSSBLK=y, but CONFIG_DAX=m.
Fix this by adding "depends on DAX || DAX=n" to config DCSSBLK, to make it
explicit that we want either no DAX, or the same "y/m" for both config DAX
and DCSSBLK, similar to config BLK_DEV_DM.
This also requires removing the "select DAX" from config DCSSBLK_DAX, or
else there would be a recursive dependency detected. DCSSBLK_DAX is marked
as BROKEN at the moment, and won't work well with DAX anyway, so it doesn't
really matter if it is selected.
Fixes: 653d7825c149 ("dcssblk: mark DAX broken, remove FS_DAX_LIMITED support")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504291604.pvjonhWX-lkp@intel.com/
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
In case of stack corruption stack_invalid() is called and the expectation
is that register r10 contains the last breaking event address. This
dependency is quite subtle and broke a couple of years ago without that
anybody noticed.
Fix this by getting rid of the dependency and read the last breaking event
address from lowcore.
Fixes: 56e62a737028 ("s390: convert to generic entry")
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
While testing Open vSwitch with Nvidia ConnectX-6 NIC, it was noticed
that it didn't offload TC flows into the NIC, and its log contained
many messages such as:
"failed to offload flow: No such file or directory: <network device name>"
and, upon enabling more versose logging, additionally:
"received NAK error=2 - TC classifier not found"
The options enabled here are listed as requirements in Nvidia online
documentation, among other options that were already enabled. Now all
options listed by Nvidia are enabled..
This option is also added because Fedora has it:
CONFIG_NET_EMATCH
Signed-off-by: Konstantin Shkolnyy <kshk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
ConnectX-6 is the first VDPA-capable NIC. For earlier NICs, Nvidia
implements a VDPA emulation in s/w, which hasn't been validated on s390.
Add options necessary for VDPA to work.
These options are also added because Fedora has them:
CONFIG_VDPA_SIM
CONFIG_VDPA_SIM_NET
CONFIG_VDPA_SIM_BLOCK
CONFIG_VDPA_USER
CONFIG_VP_VDPA
Signed-off-by: Konstantin Shkolnyy <kshk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Nathan reported [1] that when built with clang, the um kernel
crashes pretty much immediately. This turned out to be an issue
with the inline assembly I had added, when clang used %rax/%eax
for both operands. Reorder it so current->thread.segv_continue
is written first, and then the lifetime of _faulted won't have
overlap with the lifetime of segv_continue.
In the email thread Benjamin also pointed out that current->mm
is only NULL for true kernel tasks, but we could do this for a
userspace task, so the current->thread.segv_continue logic must
be lifted out of the mm==NULL check.
Finally, while looking at this, put a barrier() so the NULL
assignment to thread.segv_continue cannot be reorder before
the possibly faulting operation.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://lore.kernel.org/r/20250402221254.GA384@ax162 [1]
Fixes: d1d7f01f7cd3 ("um: mark rodata read-only and implement _nofault accesses")
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
