| Age | Commit message (Collapse) | Author |
|---|
|
Fix inaccurate information about PHY muxing, and merge standalone and
multi-chip module MT7530 configuration methods.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230212131258.47551-1-arinc.unal@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The dsa-port.yaml binding had several references that can be common to all
ethernet ports, not just dsa-specific ones. Break out the generic bindings
to ethernet-switch-port.yaml they can be used by non-dsa drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dsa.yaml bindings had references that can apply to non-dsa switches. To
prevent duplication of this information, keep the dsa-specific information
inside dsa.yaml and move the remaining generic information to the newly
created ethernet-switch.yaml.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dsa.yaml contains a reference to dsa-port.yaml, so a duplicate reference to
the binding isn't necessary. Remove this unnecessary reference.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dsa.yaml binding contains duplicated bindings for address and size
cells, as well as the reference to dsa-port.yaml. Instead of duplicating
this information, remove the reference to dsa-port.yaml and include the
full reference to dsa.yaml.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Explicitly allow additional properties for both the ethernet-port and
ethernet-ports properties. This specifically will allow the qca8k.yaml
binding to use shared properties.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA switches can fall into one of two categories: switches where all ports
follow standard '(ethernet-)?port' properties, and switches that have
additional properties for the ports.
The scenario where DSA ports are all standardized can be handled by
switches with a reference to the new 'dsa.yaml#/$defs/ethernet-ports'.
The scenario where DSA ports require additional properties can reference
'$dsa.yaml#' directly. This will allow switches to reference these standard
definitions of the DSA switch, but add additional properties under the port
nodes.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Alvin Šipraga <alsi@bang-olufsen.dk> # realtek
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
switch node
The children of the switch node don't have a unit address, and therefore
should not need the #address-cells or #size-cells entries. Fix the example
schemas accordingly.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The property use-bcm-hdr was documented as an entry under the ports node
for the bcm_sf2 DSA switch. This property is actually evaluated for each
port. Correct the documentation to match the actual behavior and properly
reference dsa-port.yaml for additional properties of the node.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAINTAINERS file has Andrew Lunn, Florian Fainelli, and Vladimir Oltean
listed as the maintainers for generic dsa bindings. Update dsa.yaml and
dsa-port.yaml accordingly.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Devicetree bindings document does not have to say in the title that
it is a "binding", but instead just describe the hardware.
Drop trailing "Node|Tree|Generic bindings" in various forms (also with
trailing full stop):
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [nN]ode [bB]indings\?\.\?$/title: \1/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [tT]ree [bB]indings\?\.\?$/title: \1/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [gG]eneric [bB]indings\?\.\?$/title: \1/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [bB]indings\? description\.\?$/title: \1/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [bB]indings\? document\.\?$/title: \1/' {} \;
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # MMC
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Acked-by: Vinod Koul <vkoul@kernel.org> # phy
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221216163815.522628-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The Devicetree bindings document does not have to say in the title that
it is a "Devicetree binding", but instead just describe the hardware.
Drop trailing "Devicetree bindings" in various forms (also with
trailing full stop):
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [dD]evice[ -]\?[tT]ree [bB]indings\?\.\?$/title: \1/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [dD]evice[ -]\?[nN]ode [bB]indings\?\.\?$/title: \1/' {} \;
find Documentation/devicetree/bindings/ -type f -name '*.yaml' \
-not -name 'trivial-devices.yaml' \
-exec sed -i -e 's/^title: \(.*\) [dD][tT] [bB]indings\?\.\?$/title: \1/' {} \;
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # IIO
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # MMC
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # input
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # media
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Link: https://lore.kernel.org/r/20221216163815.522628-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The current DSA maintainers are Florian Fainelli, Andrew Lunn and Vladimir
Oltean. Update the hellcreek binding accordingly.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221212081546.6916-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'reg' without any constraints allows multiple items which is not the
intention in DSA port schema (as physical port is expected to have only
one address).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows multiple phandles to be specified for pcs-handle, such as
when multiple PCSs are present for a single MAC. To differentiate
between them, also add a pcs-handle-names property.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Expand the description of the gpio-controller property to include the
controllable pins of the MT7530 switch.
The gpio-controller property is only used for the MT7530 switch. Therefore,
invalidate it for the MT7531 switch.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of muxing phy0 of the MT7530 switch, the switch and the phy
will have the same address on the mdio bus, 0. This causes the ethernet
driver to fail since devices on the mdio bus cannot share an address.
Any address can be used for the switch, therefore, change the switch
address to 0x1f.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the free-form description of device tree bindings for VSC9959
and VSC9953 with a YAML formatted dt-schema description. This contains
more or less the same information, but reworded to be a bit more
succint.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220913125806.524314-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is not used by the DSA dt-binding, so remove it from all examples.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The common dsa-port.yaml does this (and more) since commit 2ec2fb8331af
("dt-bindings: net: dsa: make phylink bindings required for CPU/DSA
ports").
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The fact that some DSA device trees use 'label = "cpu"' for the CPU port
is nothing but blind cargo cult copying. The 'label' property was never
part of the DSA DT bindings for anything except the user ports, where it
provided a hint as to what name the created netdevs should use.
DSA does use the "cpu" port label to identify a CPU port in dsa_port_parse(),
but this is only for non-OF code paths (platform data).
The proper way to identify a CPU port is to look at whether the
'ethernet' phandle is present.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the description of the binding.
- Describe the switches, which SoCs they are in, or if they are standalone.
- Explain the various ways of configuring MT7530's port 5.
- Remove phy-mode = "rgmii-txid" from description. Same code path is
followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define acceptable phy-mode values for the CPU ports of mt7530 and mt7531
switches. Remove relevant information from the description of the binding.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the examples on the binding.
- Add examples which include a wide variation of configurations.
- Make example comments YAML comment instead of DT binding comment.
- Add interrupt controller to the examples. Include header file for
interrupt.
- Change reset line for MT7621 examples.
- Pretty formatting for the examples.
- Change switch reg to 0.
- Change port labels to fit the example, change port 4 label to wan.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
- Add description for reset-gpios.
- Invalidate reset-gpios if mediatek,mcm is used. We cannot use multiple
reset lines at the same time.
- Invalidate mediatek,mcm if the compatible device is mediatek,mt7531.
There is no multi-chip module version of mediatek,mt7531.
- Require mediatek,mcm for mediatek,mt7621 as the compatible string is only
used for the multi-chip module version of MT7530.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the description of mediatek,mcm. mediatek,mcm is not used on MT7623NI.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make trivial changes on the binding.
- Update title to include MT7531 switch.
- Add me as a maintainer. List maintainers in alphabetical order by first
name.
- Add description to compatible strings.
- Stretch descriptions up to the 80 character limit.
- Remove lists for single items.
- Remove requiring reg as it's already required by dsa-port.yaml.
- Define acceptable reg values for the CPU ports.
- Remove quotes from $ref: "dsa.yaml#".
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is desirable that new DSA drivers are written to expect that all
their ports register with phylink, and not rely on the DSA core's
workarounds to skip this process.
To that end, DSA is being changed to warn existing drivers when such DT
blobs are in use, and to opt new drivers out of the workarounds.
Introduce another layer of validation in the DSA DT schema, and assert
that CPU and DSA ports must have phylink-related properties present.
Suggested-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To prevent warnings during "make dt_bindings_check" after dsa-port.yaml
will make phylink properties mandatory, add phy-mode = "internal" to the
example.
This new property is taken straight out of the SoC dtsi at
arch/arm/boot/dts/r9a06g032.dtsi, so it seems likely that only the
example needs to be fixed, rather than DT blobs in circulation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ksz_switch_chips[] element for KSZ9477 says that port 5 is an xMII
port and it supports speeds of 10/100/1000. The device tree example does
declare a fixed-link at 1000, and RGMII is the only one of those modes
that supports this speed, so use this phy-mode.
The microchip,ksz8565 compatible string is not supported by the
microchip driver, however on Microchip's product page it says that there
are 5 ports, 4 of which have internal PHYs and the 5th is an
MII/RMII/RGMII port. It's a bit strange that this is port@6, but it is
probably just the way it is. Select an RGMII phy-mode for this one as
well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Looking at b53_srab_phylink_get_caps() I get no indication of what PHY
modes does port 8 support, since it is implemented circularly based on
the p->mode retrieved from the device tree (and in PHY_INTERFACE_MODE_NA
it reports nothing to supported_interfaces).
However if I look at the b53_switch_chips[] element for BCM58XX_DEVICE_ID,
I see that port 8 is the IMP port, and SRAB means the IMP port is
internal to the SoC. So use phy-mode = "internal" in the example.
Note that this will make b53_srab_phylink_get_caps() go through the
"default" case and report PHY_INTERFACE_MODE_INTERNAL to
supported_interfaces, which is probably a good thing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
to example
Looking at hellcreek_phylink_get_caps(), I see that depending on whether
is_100_mbits is set, speeds of 1G or of 100M will be advertised. The
de1soc_r1_pdata sets is_100_mbits to true.
The PHY modes declared in the capabilities are MII, RGMII and GMII. GMII
doesn't support 100Mbps, and as for RGMII, it would be a bit implausible
to me to support this PHY mode but limit it to only 25 MHz. So I've
settled on MII as a phy-mode in the example, and a fixed-link of
100Mbps.
As a side note, there exists such a thing as "rev-mii", because the MII
protocol is asymmetric, and "mii" is the designation for the MAC side
(expected to be connected to a PHY), and "rev-mii" is the designation
for the PHY side (expected to be connected to a MAC). I wonder whether
"mii" or "rev-mii" should actually be used here, since this is a CPU
port and presumably connected to another MAC.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Judging by xrs700x_phylink_get_caps(), I deduce that this switch
supports the RGMII modes on port 3, so state this phy-mode in the
example, such that users are encouraged to not rely on avoiding phylink
for this port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Absolute path to other DT schema is preferred over relative one.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220726115650.100726-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 'reg' property is missing from the mediatek,mt7530 schema which
results in the following warning once 'unevaluatedProperties' is fixed:
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.example.dtb: switch@0: Unevaluated properties are not allowed ('reg' was unexpected)
Fixes: e0dda3119741 ("dt-bindings: net: dsa: convert binding for mediatek switches")
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220701222240.1706272-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Describe the switch interrupts (dlr, switch, prp, hub, pattern) which
are connected to the GIC.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation in .yaml format and updates to the MAINTAINERS
Also 'make dt_binding_check' is passed.
RGMII internal delay values for the mac is retrieved from
rx-internal-delay-ps & tx-internal-delay-ps as per the feedback from
v3 patch series.
https://lore.kernel.org/netdev/20210802121550.gqgbipqdvp5x76ii@skbuf/
It supports only the delay value of 0ns and 2ns.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add bindings for Renesas RZ/N1 Advanced 5 port switch. This switch is
present on Renesas RZ/N1 SoC and was probably provided by MoreThanIP.
This company does not exists anymore and has been bought by Synopsys.
Since this IP can't be find anymore in the Synospsy portfolio, lets use
Renesas as the vendor compatible for this IP.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A board may have no independent reset-line, so reset cannot be used
inside switch driver.
E.g. on Bananapi-R2 Pro switch and gmac are connected to same reset-line.
Resets should be acquired only to 1 device/driver. This prevents reset to
be bound to switch-driver if reset is already used for gmac. If reset is
only used by switch driver it resets the switch *and* the gmac after the
mdio bus comes up resulting in mdio bus goes down. It takes some time
until all is up again, switch driver tries to read from mdio, will fail
and defer the probe. On next try the reset does the same again.
Make reset optional for such boards.
Allow port 5 as cpu-port and phy-mode rgmii for mt7531.
- MT7530 supports RGMII on port 5 and RGMII/TRGMII on port 6.
- MT7531 supports on port 5 RGMII and SGMII (dual-sgmii) and
SGMII on port 6.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert txt binding to yaml binding for Mediatek switches.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
SPI peripheral device bindings need to reference spi-peripheral-props.yaml
in order to use various SPI controller specific properties. Otherwise,
the unevaluatedProperties check will reject any controller specific
properties.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220531220122.2412711-1-robh@kernel.org
|
|
Compatible strings are used to help the driver find the chip ID/version
register for each chip family. After that, the driver can setup the
switch accordingly. Keep only the first supported model for each family
as a compatible string and reference other chip models in the
description.
The removed compatible strings have never been used in a released kernel.
Link: https://lore.kernel.org/netdev/20220414014055.m4wbmr7tdz6hsa3m@bang-olufsen.dk/
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Link: https://lore.kernel.org/r/20220418233558.13541-1-luizluca@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Absolute paths in $ref should always begin with '/schemas'. The tools
mostly work with it omitted, but for correctness the path should be
everything except the hostname as that is taken from the schema's $id
value. This scheme is defined in the json-schema spec.
Cc: Hector Martin <marcan@marcan.st>
Cc: Sven Peter <sven@svenpeter.dev>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mukesh Savaliya <msavaliy@codeaurora.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: Bayi Cheng <bayi.cheng@mediatek.com>
Cc: Chuanhong Guo <gch981213@gmail.com>
Cc: Min Guo <min.guo@mediatek.com>
Cc: netdev@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mark Brown <broonie@debian.org>
Link: https://lore.kernel.org/r/20220325215652.525383-1-robh@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the
source level syntax information. There's a bunch of schema fixes as a
result of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial
filename or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated
HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass
messages also now print by default at PR_INFO level to help test
automation.
* tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (96 commits)
dt-bindings: kbuild: Make DT_SCHEMA_LINT a recursive variable
dt-bindings: nvmem: add U-Boot environment variables binding
dt-bindings: ufs: qcom: Add SM6350 compatible string
dt-bindings: dmaengine: sifive,fu540-c000: include generic schema
dt-bindings: gpio: pca95xx: drop useless consumer example
Revert "of: base: Introduce of_alias_get_alias_list() to check alias IDs"
dt-bindings: virtio,mmio: Allow setting devices 'dma-coherent'
dt-bindings: gnss: Add two more chips
dt-bindings: gnss: Rewrite sirfstar binding in YAML
dt-bindings: gnss: Modify u-blox to use common bindings
dt-bindings: gnss: Rewrite common bindings in YAML
dt-bindings: ata: ahci-platform: Add rk3568-dwc-ahci compatible
dt-bindings: ata: ahci-platform: Add power-domains property
dt-bindings: ata: ahci-platform: Convert DT bindings to yaml
dt-bindings: kbuild: Use DTB files for validation
dt-bindings: kbuild: Pass DT_SCHEMA_FILES to dt-validate
dt-bindings: Add QEMU virt machine compatible
dt-bindings: arm: Convert QEMU fw-cfg to DT schema
dt-bindings: i2c: at91: Add SAMA7G5 compatible strings list
dt-bindings: i2c: convert i2c-at91 to json-schema
...
|
|
Realtek rtl8365mb DSA driver can use these two tag formats.
Cc: devicetree@vger.kernel.org
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Schema changes:
- support for mdio-connected switches (mdio driver), recognized by
checking the presence of property "reg"
- new compatible strings for rtl8367s and rtl8367rb
- "interrupt-controller" was not added as a required property. It might
still work polling the ports when missing.
Examples changes:
- renamed "switch_intc" to make it unique between examples
- removed "dsa-mdio" from mdio compatible property
- renamed phy@0 to ethernet-phy@0 (not tested with real HW)
phy@ requires #phy-cells
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'phandle-array' type is a bit ambiguous. It can be either just an
array of phandles or an array of phandles plus args. Many schemas for
phandle-array properties aren't clear in the schema which case applies
though the description usually describes it.
The array of phandles case boils down to needing:
items:
maxItems: 1
The phandle plus args cases should typically take this form:
items:
- items:
- description: A phandle
- description: 1st arg cell
- description: 2nd arg cell
With this change, some examples need updating so that the bracketing of
property values matches the schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220119015038.2433585-1-robh@kernel.org
|
|
Document the new microchip,synclko-disable property which can be
specified to disable the reference clock output from the device if not
required by the board design.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"Bindings:
- DT schema conversions for Samsung clocks, RNG bindings, Qcom
Command DB and rmtfs, gpio-restart, i2c-mux-gpio, i2c-mux-pinctl,
Tegra I2C and BPMP, pwm-vibrator, Arm DSU, and Cadence macb
- DT schema conversions for Broadcom platforms: interrupt
controllers, STB GPIO, STB waketimer, STB reset, iProc MDIO mux,
iProc PCIe, Cygnus PCIe PHY, PWM, USB BDC, BCM6328 LEDs, TMON,
SYSTEMPORT, AMAC, Northstar 2 PCIe PHY, GENET, moca PHY, GISB
arbiter, and SATA
- Add binding schemas for Tegra210 EMC table, TI DC-DC converters,
- Clean-ups of MDIO bus schemas to fix 'unevaluatedProperties' issues
- More fixes due to 'unevaluatedProperties' enabling
- Data type fixes and clean-ups of binding examples found in
preparation to move to validating DTB files directly (instead of
intermediate YAML representation.
- Vendor prefixes for T-Head Semiconductor, OnePlus, and Sunplus
- Add various new compatible strings
DT core:
- Silence a warning for overlapping reserved memory regions
- Reimplement unittest overlay tracking
- Fix stack frame size warning in unittest
- Clean-ups of early FDT scanning functions
- Fix handling of "linux,usable-memory-range" on EFI booted systems
- Add support for 'fail' status on CPU nodes
- Improve error message in of_phandle_iterator_next()
- kbuild: Disable duplicate unit-address warnings for disabled nodes"
* tag 'devicetree-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (114 commits)
dt-bindings: net: mdio: Drop resets/reset-names child properties
dt-bindings: clock: samsung: convert S5Pv210 to dtschema
dt-bindings: clock: samsung: convert Exynos5410 to dtschema
dt-bindings: clock: samsung: convert Exynos5260 to dtschema
dt-bindings: clock: samsung: extend Exynos7 bindings with UFS
dt-bindings: clock: samsung: convert Exynos7 to dtschema
dt-bindings: clock: samsung: convert Exynos5433 to dtschema
dt-bindings: i2c: maxim,max96712: Add bindings for Maxim Integrated MAX96712
dt-bindings: iio: adi,ltc2983: Fix 64-bit property sizes
dt-bindings: power: maxim,max17040: Fix incorrect type for 'maxim,rcomp'
dt-bindings: interrupt-controller: arm,gic-v3: Fix 'interrupts' cell size in example
dt-bindings: iio/magnetometer: yamaha,yas530: Fix invalid 'interrupts' in example
dt-bindings: clock: imx5: Drop clock consumer node from example
dt-bindings: Drop required 'interrupt-parent'
dt-bindings: net: ti,dp83869: Drop value on boolean 'ti,max-output-impedance'
dt-bindings: net: wireless: mt76: Fix 8-bit property sizes
dt-bindings: PCI: snps,dw-pcie-ep: Drop conflicting 'max-functions' schema
dt-bindings: i2c: st,stm32-i2c: Make each example a separate entry
dt-bindings: net: stm32-dwmac: Make each example a separate entry
dt-bindings: net: Cleanup MDIO node schemas
...
|
|
The schemas for MDIO bus nodes range from missing to duplicating
everything in mdio.yaml. The MDIO bus node schemas only need to
reference mdio.yaml, define any binding specific properties, and define
'unevaluatedProperties: false'. This ensures that MDIO nodes only
contain defined properties. With this, any duplicated properties can
be removed.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Cc: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Cc: "Fernández Rojas" <noltari@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: "G. Jaya Kumaran" <vineetha.g.jaya.kumaran@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220105151009.3093506-1-robh@kernel.org
|
