summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts
AgeCommit message (Collapse)Author
2025-05-12ARM: dts: vt8500: add DT nodes for the system config ID registerAlexey Charkov
Every VIA/WonderMedia SoC has a 32-bit chip ID register at the MMIO address 0xd8120000. Add respective device tree nodes to let the system code access it at runtime for the selection of appropriate hardware quirks where needed. Signed-off-by: Alexey Charkov <alchark@gmail.com> Link: https://lore.kernel.org/r/20250503-wmt-soc-driver-v3-3-2daa9056fa10@gmail.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2025-05-12ARM: dts: vt8500: Add VIA APC Rock/Paper boardAlexey Charkov
APC Rock is a development board based on WonderMedia WM8590 released around 2013. Paper is the same board, but with the VGA port left unpopulated, and shipped with a recycled cardboard case Its hardware includes: * Single-core Cortex-A9 CPU at 800 MHz * 512MB DDR3 RAM * 4GB NAND flash * 8MB SPI NOR flash * ARM Mali-400 GPU * HDMI output (type A) capable of 1080p * VGA output (on Rock, but not on Paper) * 2x USB 2.0 type A * 1x USB 2.0 OTG (microUSB connector) * microSD slot * 10/100M Ethernet * 3.5mm minijack connector with combined headphones/mic * Half-height miniPCIe slot (with only USB 2.0 signals) Signed-off-by: Alexey Charkov <alchark@gmail.com> Link: https://lore.kernel.org/r/20250425-apc_paper_binding-v5-2-3aef49e97332@gmail.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2025-05-11Merge branch 'arm32-for-6.15' into arm32-for-6.16Bjorn Andersson
The v6.15 PR contained the transition to "qcom,calibration-variant" and was not accepted due to the risk of breaking bisection support. Merge the arm32-for-6.15 tag in order to bring these patches into v6.16.
2025-05-11ARM: dts: qcom: msm8226-motorola-falcon: specify vddio_disp output voltageStanislav Jakubek
After some digging in downstream sources, it was found that the vddio_disp regulator's output voltage is 1.8V. This is further confirmed by the troubleshooting guide. Specify its output voltage as such. While at it, add a comment specifying the IC, which according to the schematic is the TI TPS22902. Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/6143603464a65aebbed281fe6c6164316dd07269.1746711762.git.stano.jakubek@gmail.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
2025-05-11ARM: dts: qcom: msm8226-motorola-falcon: limit TPS65132 to 5.4VStanislav Jakubek
After some digging in downstream sources, it was found that the TPS65132 outputs are fixed to +5.4V and -5.4V respectively. This is further confirmed on runtime through debugfs, the troubleshooting guide confirms this as well. Specify these limits as such. Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/b67ed6c7813fa52cf00b473dded9b5042102f593.1746711762.git.stano.jakubek@gmail.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
2025-05-11ARM: dts: qcom: msm8226-motorola-falcon: add I2C clock frequenciesStanislav Jakubek
While the currently supported hardware works fine with the default clock frequencies of 100000 on both I2C2 and I2C3, downstream sources list the frequencies as 100000 for I2C2 and 400000 for I2C3. Update them as such. Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/5a8191e3758e0df78b4213102f25ceadc28cd427.1746711762.git.stano.jakubek@gmail.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
2025-05-11ARM: dts: qcom: msm8226-motorola-falcon: add clocks, power-domain to simpleFBStanislav Jakubek
Makes the display work without clk_ignore_unused and pd_ignore_unused. Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/cdb6915bf40c055c77a0beb2f49c20458adf7481.1746711762.git.stano.jakubek@gmail.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
2025-05-10Merge tag 'tegra-for-6.16-arm-dt' of ↵Arnd Bergmann
https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt ARM: tegra: Device tree changes for v6.16-rc1 Use standard names for the APBDMA controller device tree nodes, add support for the ASUS Transformer Pad LTE TF300TL and clean up the Apalis evaluation board by removing the unused pcie-switch node. * tag 'tegra-for-6.16-arm-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: ARM: tegra: apalis-eval: Remove pcie-switch node ARM: tegra: Add device-tree for ASUS Transformer Pad LTE TF300TL ARM: tegra: Rename the apbdma nodename to match with common dma-controller binding Link: https://lore.kernel.org/r/20250509212604.2849901-2-treding@nvidia.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09Merge tag 'v6.16-rockchip-dts32-1' of ↵Arnd Bergmann
https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt Graphics support for the old rk3066-marsboard (hdmi + Mali400 gpu), rk3036 improvements (mmc asliases, hdmi refclk), dropping of redundant clock-latency props. * tag 'v6.16-rockchip-dts32-1' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: ARM: dts: rockchip: enable Mali gpu on rk3066 marsboard ARM: dts: rockchip: enable hdmi on rk3066 marsboard Revert "ARM: dts: rockchip: drop grf reference from rk3036 hdmi" ARM: dts: rockchip: Add ref clk for hdmi ARM: dts: rockchip: Drop redundant CPU "clock-latency" ARM: dts: rockchip: Add aliases for rk3036-kylin MMC devices Link: https://lore.kernel.org/r/22686731.EfDdHjke4D@diego Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09Merge tag 'arm-soc/for-6.16/devicetree' of ↵Arnd Bergmann
https://github.com/Broadcom/stblinux into soc/dt This pull request contains Broadcom ARM-based SoC Device Tree changes for 6.16, please pull the following: - Arthur adds a pinctrl node for BCM21664 and updates BCM23550 to use it, he also drops the DTS file for the BCM59056 PMU chip and leaving that board level DTS files - Stefan documents and adds support for the Raspberry Pi 2 2nd revision. * tag 'arm-soc/for-6.16/devicetree' of https://github.com/Broadcom/stblinux: arm64: dts: bcm: Add reference to RPi 2 (2nd rev) ARM: dts: bcm: Add support for Raspberry Pi 2 (2nd rev) dt-bindings: arm: bcm2835: Add Raspberry Pi 2 (2nd rev) ARM: dts: Drop DTS for BCM59056 PMU ARM: dts: bcm2166x: Add bcm2166x-pinctrl DTSI ARM: dts: bcm2166x-common: Add pinctrl node Link: https://lore.kernel.org/r/20250505165810.1948927-1-florian.fainelli@broadcom.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09Merge tag 'renesas-dts-for-v6.16-tag2' of ↵Arnd Bergmann
https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt Renesas DTS updates for v6.16 (take two) - Add CANFD support for the RZ/G3E SoC and the RZ/G3E SMARC Carrier-II EVK development board, - Add support for Ethernet port A, 9-pin D-sub serial, and USB on the RZN1D-DB and RZN1D-EB development and expansion boards, - Add sound support for the Retronix Sparrow Hawk board, - Add General PWM Timer (GPT) support for the RZ/G2L and RZ/V2L SoCs and SMARC EVK boards, - Miscellaneous fixes and improvements. * tag 'renesas-dts-for-v6.16-tag2' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: ARM: dts: renesas: r9a06g032-rzn1d400-eb: Enable USB host port ARM: dts: renesas: r9a06g032-rzn1d400-db: Add pinmux for the CPLD arm64: dts: renesas: white-hawk-single: Improve Ethernet TSN description ARM: dts: renesas: r9a06g032-rzn1d400-db: Enable USB device port ARM: dts: renesas: r9a06g032-rzn1d400-eb: Describe 9-pin D-sub serial port arm64: dts: renesas: beacon-renesom: Align wifi node name with bindings arm64: dts: renesas: rzg2l-smarc: Enable GPT on carrier board arm64: dts: renesas: r9a07g054: Add GPT support arm64: dts: renesas: r9a07g044: Add GPT support arm64: dts: renesas: sparrow-hawk: Add MSIOF Sound support ARM: dts: renesas: r9a06g032-rzn1d400-eb: Add GMAC1 port arm64: dts: renesas: r9a09g047e57-smarc: Enable CAN Transceiver arm64: dts: renesas: r9a09g047e57-smarc: Enable CANFD arm64: dts: renesas: r9a09g047: Add CANFD node Link: https://lore.kernel.org/r/cover.1746798755.git.geert+renesas@glider.be Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09Merge tag 'renesas-dts-for-v6.16-tag1' of ↵Arnd Bergmann
https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt Renesas DTS updates for v6.16 - Add SDHI, ICU, I2C, PMIC, and GPU support on the RZ/G3E SoC and the RZ/G3E SoM and SMARC Carrier-II EVK development board, - Add internal SDHI regulator support on the RZ/V2H(P) SoC, - Add UFS tuning parameters in E-FUSE on the R-Car S4-8 ES1.2 SoC, - Add support for Ethernet ports C and D, I2C, keys, and SDHI on the RZ/N1D SoC and the RZN1D-DB and RZN1D-EB development and expansion boards, - Add initial support for the RZ/V2N (R9A09G056) and the RZ/V2N EVK board, - Add support for the Retronix Sparrow Hawk board, which is based on R-Car V4H ES3.0, - Add ISP core support on R-Car V3U, V4H, and V4M, - Miscellaneous fixes and improvements. * tag 'renesas-dts-for-v6.16-tag1' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (29 commits) arm64: dts: renesas: r8a779h0: Add ISP core function block arm64: dts: renesas: r8a779g0: Add ISP core function block arm64: dts: renesas: r8a779a0: Add ISP core function block arm64: dts: renesas: r8a779g3: Add Retronix R-Car V4H Sparrow Hawk board support arm64: dts: renesas: rzg3e-smarc-som: Enable Mali-G52 arm64: dts: renesas: r9a09g047: Add Mali-G52 GPU node arm64: dts: renesas: rzg3e-smarc-som: Add RAA215300 pmic support arm64: dts: renesas: rzg3e-smarc-som: Add I2C2 device pincontrol ARM: dts: renesas: r9a06g032-rzn1d400-eb: describe SD card port ARM: dts: renesas: r9a06g032: Describe SDHCI controllers arm64: dts: renesas: Add initial device tree for RZ/V2N EVK arm64: dts: renesas: Add initial SoC DTSI for RZ/V2N dt-bindings: pinctrl: renesas: Document RZ/V2N SoC dt-bindings: clock: renesas: Document RZ/V2N SoC CPG dt-bindings: soc: renesas: Document SYS for RZ/V2N SoC dt-bindings: soc: renesas: Document Renesas RZ/V2N SoC variants and EVK ARM: dts: renesas: r9a06g032-rzn1d400-db: Describe keys ARM: dts: renesas: r9a06g032-rzn1d400-eb: Describe I2C bus ARM: dts: renesas: r9a06g032-rzn1d400-db: Describe I2C bus ARM: dts: renesas: r9a06g032: Describe I2C controllers ... Link: https://lore.kernel.org/r/cover.1745582596.git.geert+renesas@glider.be Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09Merge tag 'socfpga_dts_updates_for_v6.15' of ↵Arnd Bergmann
https://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into soc/dt SoCFPGA DTS updates for v6.15 - Updates to dt-bindings - Document Agilex5 NAND daughter board - Convert Stratix10 FPGA Manager to json-schema - Convert Stratix10 Service Layer to json-schema - Add document for Terasic's DE10-nano board - Add support for Agilex5 NAND daughter board - Add basic support for Terasic's DE10-nano board * tag 'socfpga_dts_updates_for_v6.15' of https://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: arm64: dts: socfpga: agilex: Add dma channel id for spi arm64: dts: socfpga: agilex5: add led and memory nodes arm64: dts: intel: socfpga_agilex: add frequencies to internal oscillators ARM: dts: socfpga: Add basic support for Terrasic's de10-nano dt-bindings: altera: Add compatible for Terasic's DE10-nano arm64: dts: socfpga: agilex5: add qspi flash node dt-bindings: firmware: stratix10: Convert to json-schema dt-bindings: fpga: stratix10: Convert to json-schema arm64: dts: socfpga: agilex5: fix gpio0 address arm64: dts: socfpga: agilex5: add NAND daughter board dt-bindings: intel: document Agilex5 NAND daughter board Link: https://lore.kernel.org/r/20250326121152.1739873-1-dinguyen@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09ARM: dts: vt8500: use correct ohci/ehci node namesWolfram Sang
They should be named "usb@". Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/20250330193833.21970-12-wsa+renesas@sang-engineering.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09ARM: dts: ti: omap: use correct ohci/ehci node namesWolfram Sang
They should be named "usb@". Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/20250330193833.21970-11-wsa+renesas@sang-engineering.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09ARM: dts: st: use correct ohci/ehci node namesWolfram Sang
They should be named "usb@". Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/20250330193833.21970-10-wsa+renesas@sang-engineering.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09ARM: dts: nxp: lpc: use correct ohci/ehci node namesWolfram Sang
They should be named "usb@". Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/20250330193833.21970-9-wsa+renesas@sang-engineering.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09ARM: dts: marvell: use correct ohci/ehci node namesWolfram Sang
They should be named "usb@". Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/20250330193833.21970-8-wsa+renesas@sang-engineering.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09Merge tag 'amlogic-fixes-for-v6.15' of ↵Arnd Bergmann
https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/fixes Amlogic Fixes for v6.15: - fix reference to unknown/untested PWM clock on ARM/ARM64 boards - fix missing clkc_audio node on dreambox ARM64 DT * tag 'amlogic-fixes-for-v6.15' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux: arm64: dts: amlogic: dreambox: fix missing clkc_audio node arm64: dts: amlogic: g12: fix reference to unknown/untested PWM clock arm64: dts: amlogic: gx: fix reference to unknown/untested PWM clock ARM: dts: amlogic: meson8b: fix reference to unknown/untested PWM clock ARM: dts: amlogic: meson8: fix reference to unknown/untested PWM clock Link: https://lore.kernel.org/r/e9c520a1-b986-49e1-b9b1-67511c187716@linaro.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-05-09ARM: dts: amlogic: meson8-fernsehfee3: Describe regulatorsJ. Neuschäfer
The fernsehfee3 board uses a Ricoh RN5T618 PMIC to generate various voltages. Board schematics are not available, but the regulator voltages found in /sys/kernel/debug/regulator/regulator_summary match those in meson8m2-mxiii-plus.dts: DCDC1 0 0 0 unknown 1100mV 0mA 0mV 0mV DCDC2 0 0 0 unknown 1150mV 0mA 0mV 0mV DCDC3 0 0 0 unknown 1500mV 0mA 0mV 0mV LDO1 0 0 0 unknown 2900mV 0mA 0mV 0mV LDO2 0 0 0 unknown 1800mV 0mA 0mV 0mV LDO3 0 0 0 unknown 1800mV 0mA 0mV 0mV LDO4 0 0 0 unknown 2850mV 0mA 0mV 0mV LDO5 0 0 0 unknown 1800mV 0mA 0mV 0mV LDORTC1 0 0 0 unknown 2700mV 0mA 0mV 0mV LDORTC2 0 0 0 unknown 900mV 0mA 0mV 0mV This patch takes the following approach: - Copy RN5T618 regulator nodes from meson8m2-mxiii-plus.dts - Remove some of the regulator names, which do not seem to apply - Verify regulator supply relations by starting without any relations (and without regulator-always-on) and seeing what breaks when the kernel turns off "unused" regulators. This results in the following observations: - When LDO1 is turned off, the board resets - When DCDC1, DCDC2, DCDC3, LDO2, or LDO5 are turned off, the board (as observed through the serial port) stops running, so these must stay on at all times. - LDO4 (VCC2V8) appears to be unused on this board. - LDO3 (VCC1V8_USB) must stay on in order for USB to work, both the external USB ports and the internal USB wifi module. The cpu-supply and mali-supply relations are also copied from meson8m2-mxiii-plus.dts Signed-off-by: J. Neuschäfer <j.ne@posteo.net> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20250428-fernsehfee-v2-4-293b98a43a91@posteo.net Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
2025-05-09ARM: dts: amlogic: Add TCU Fernsehfee 3.0J. Neuschäfer
Fernsehfee[1] ("TV fairy") 3.0 is a set-top box with HDMI input and output ports. It originally ran Android 4.4 and a Linux 3.10 kernel. The following features are tested and known to work: - Ethernet - Power LED (switching between green and red) - Power button - eMMC - SD Card - USB - Wifi The following features are untested or not working: - HDMI input and output - Infrared remote control input and output [1]: https://fernsehfee.de/ (German), https://telefairy.com/ (English) Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: J. Neuschäfer <j.ne@posteo.net> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20250428-fernsehfee-v2-3-293b98a43a91@posteo.net Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
2025-05-09ARM: dts: mxs: use padconfig macrosDario Binacchi
Convert mx2{3,8} dts files to use the padconfig macros defined in mxs-pinfunc.h. Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-05-09ARM: dts: imx7d: update opp-table voltagesEfe Can İçöz
Update accepted voltage levels according to IMX7DCEC Table 9 Operating ranges Signed-off-by: Efe Can İçöz <efecanicoz@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-05-09ARM: dts: nxp: Align wifi node name with bindingsKrzysztof Kozlowski
Since commit 3c3606793f7e ("dt-bindings: wireless: bcm4329-fmac: Use wireless-controller.yaml schema"), bindings expect 'wifi' as node name: imx7d-remarkable2.dtb: bcrmf@1: $nodename:0: 'bcrmf@1' does not match '^wifi(@.*)?$' Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-05-08ARM: tegra: apalis-eval: Remove pcie-switch nodeFrancesco Dolcini
The compatible "plx,pex8605" does not exist, there is no DT binding for it and there was never a driver matching this compatible, remove it. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Link: https://lore.kernel.org/r/20250410063919.11199-1-francesco@dolcini.it Signed-off-by: Thierry Reding <treding@nvidia.com>
2025-05-08ARM: tegra: Add device-tree for ASUS Transformer Pad LTE TF300TLSvyatoslav Ryhel
Add device-tree for ASUS Transformer Pad LTE TF300TL, which is NVIDIA Tegra30-based tablet device. Co-developed-by: Ion Agorria <ion@agorria.com> Signed-off-by: Ion Agorria <ion@agorria.com> Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> Link: https://lore.kernel.org/r/20250503102950.32744-4-clamor95@gmail.com Signed-off-by: Thierry Reding <treding@nvidia.com>
2025-05-08ARM: tegra: Rename the apbdma nodename to match with common dma-controller ↵Charan Pedumuru
binding Rename the apbdma nodename from "dma@" to "dma-controller@" to align with linux common dma-controller binding. Signed-off-by: Charan Pedumuru <charan.pedumuru@gmail.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20250507-nvidea-dma-v4-1-6161a8de376f@gmail.com [treding@nvidia.com: adjust subject prefix for consistency] Signed-off-by: Thierry Reding <treding@nvidia.com>
2025-05-08ARM: dts: renesas: r9a06g032-rzn1d400-eb: Enable USB host portWolfram Sang
Can be used via the USB connector J20. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20250508074311.20343-6-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2025-05-08ARM: dts: renesas: r9a06g032-rzn1d400-db: Add pinmux for the CPLDWolfram Sang
The CPLD has no dedicated driver, so apply the pinmux settings with the pinmux driver instead. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20250508074311.20343-5-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2025-05-08ARM: dts: renesas: r9a06g032-rzn1d400-db: Enable USB device portWolfram Sang
Can be used via the microUSB connector CN9. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20250425100129.11942-5-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2025-05-08ARM: dts: renesas: r9a06g032-rzn1d400-eb: Describe 9-pin D-sub serial portWolfram Sang
A simple CTS/RTS capable UART on a good old D-sub connector. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20250424102805.22803-2-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2025-05-08ARM: dts: renesas: r9a06g032-rzn1d400-eb: Add GMAC1 portWolfram Sang
This port bypasses the switch and is directly connected to the GMAC. Co-developed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20250414100206.7185-2-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2025-05-08ARM: dts: am335x: Set wakeup-source for UART0Sukrut Bellary
On am335x evm[1], UART0(UART1-HW) has a wakeup capability. Set wakeup-source, which will be used in the omap serial driver to enable the device wakeup capability. [1] https://www.ti.com/tool/TMDXEVM3358 [2] AM335x TRM - https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf Signed-off-by: Sukrut Bellary <sbellary@baylibre.com> Tested-by: Judith Mendez <jm@ti.com> Link: https://lore.kernel.org/r/20250318230042.3138542-4-sbellary@baylibre.com Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2025-05-07ARM: dts: qcom: ipq4019: Drop redundant CPU "clock-latency"Rob Herring (Arm)
The "clock-latency" property is part of the deprecated opp-v1 binding and is redundant if the opp-v2 table has equal or larger values in any "clock-latency-ns". The OPP table has values of 256000, so it can be removed. Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250410-dt-cpu-schema-v2-9-63d7dc9ddd0a@kernel.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
2025-05-06arm/arm64: dts: mediatek: Add missing "#sound-dai-cells" to linux,bt-scoRob Herring (Arm)
Add missing "#sound-dai-cells" which is required by the linux,bt-sco binding. Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Link: https://lore.kernel.org/r/20250409205001.1522009-1-robh@kernel.org Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
2025-05-05ARM: dts: bcm: Add support for Raspberry Pi 2 (2nd rev)Stefan Wahren
The Raspberry Pi 2 (2nd rev) has the BCM2837 SoC instead of the BCM2836. Except of this the configuration of the board is same as the predecessor (no WLAN, no BT). Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Link: https://lore.kernel.org/r/20250418143307.59235-3-wahrenst@gmx.net Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
2025-05-05ARM: dts: rockchip: enable Mali gpu on rk3066 marsboardHeiko Stuebner
The rk3066 contains a Mali400 GPU, so enable it. There is no individual (or even controllable) supply for the GPU on the board. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/20250503201043.990933-3-heiko@sntech.de
2025-05-05ARM: dts: rockchip: enable hdmi on rk3066 marsboardHeiko Stuebner
The marsboard does have a regular hdmi-a connector and can simply use the already existing infrastructure (rk3066-hdmi) for display output. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/20250503201043.990933-2-heiko@sntech.de
2025-05-05Revert "ARM: dts: rockchip: drop grf reference from rk3036 hdmi"Andy Yan
This reverts commit 1580ccb6ed9dc76b8ff3e2d8912e8215c8b0fa6d. The HSYNC/VSYNC polarity of rk3036 HDMI are controlled by GRF. Without the polarity configuration in GRF, it can be observed from the HDMI protocol analyzer that the H/V front/back timing output by RK3036 HDMI are currently not in line with the specifications. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Tested-by: Heiko Stuebner <heiko@sntech.de> #rk3036-kylin Link: https://lore.kernel.org/r/20250422070455.432666-7-andyshrk@163.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2025-05-05ARM: dts: rockchip: Add ref clk for hdmiAndy Yan
The RK3036 HDMI DDC bus requires it's PHY's reference clock to be enabled first before normal DDC communication can be carried out. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Tested-by: Heiko Stuebner <heiko@sntech.de> #rk3036-kylin Link: https://lore.kernel.org/r/20250422070455.432666-6-andyshrk@163.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2025-05-01ARM: dts: omap4: panda: cleanup bluetoothAndreas Kemnade
Bluetooth is available on the other Panda board versions, too, so move stuff to common and specify the needed clock properly. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Reviewed-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20250427052735.88133-3-andreas@kemnade.info Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2025-05-01ARM: dts: omap4: panda: fix resources needed for WifiAndreas Kemnade
The Pandaboard needs a 32k clock in the TWL6030 to be enabled for Wifi to work. With some luck, it is enabled by some U-Boot fork. Do not rely on it and properly specify the requirement. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Reviewed-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20250427052735.88133-2-andreas@kemnade.info Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2025-04-28ARM: dts: allwinner: Align wifi node name with bindingsKrzysztof Kozlowski
Since commit 3c3606793f7e ("dt-bindings: wireless: bcm4329-fmac: Use wireless-controller.yaml schema"), bindings expect 'wifi' as node name: sun8i-h3-nanopi-neo-air.dtb: bcrmf@1: $nodename:0: 'bcrmf@1' does not match '^wifi(@.*)?$' Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://patch.msgid.link/20250424084737.105215-2-krzysztof.kozlowski@linaro.org Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2025-04-28arm/arm64: dts: allwinner: Use preferred node names for cooling mapsRob Herring (Arm)
The preferred node name for cooling map nodes is a 'map' prefix. Use 'map0' like most other platforms. Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://patch.msgid.link/20250409203613.1506047-1-robh@kernel.org Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2025-04-26ARM: dts: rockchip: Drop redundant CPU "clock-latency"Rob Herring (Arm)
The "clock-latency" property is part of the deprecated opp-v1 binding and is redundant if the opp-v2 table has equal or larger values in any "clock-latency-ns". Add any missing "clock-latency-ns" properties and remove "clock-latency". Signed-off-by: "Rob Herring (Arm)" <robh@kernel.org> Link: https://lore.kernel.org/r/20250410-dt-cpu-schema-v2-10-63d7dc9ddd0a@kernel.org Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2025-04-25ARM: dts: imx6q-apalis: remove pcie-switch nodeFrancesco Dolcini
The compatible "plx,pex8605" does not exist, there is no DT binding for it and there was never a driver matching this compatible, remove it. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-23ARM: dts: ls1021a-tqmals1021a: change sound card model nameAlexander Stein
The card name for ALSA is generated from the model name string and is limited to 16 characters. Use a shorter name to prevent cutting the name. MBLS1021A uses the same audio codec as most i.MX based starter kits by TQ-Systems. Adjust the sound card model to i.MX based platforms, as done by commit e6303798b6ac4 ("arm64: dts: imx8mp-tqma8mpql-mba8mpxl: change sound card model name"). This allows sharing a default asound.conf in BSP over all the kits. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-23ARM: dts: ls1021a-tqmals1021a: Add overlay for CDTech DC44 RGB displayAlexander Stein
This adds an overlay for the supported RGB display CDTech DC44. DCU graphics chain is configured accordingly. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-23ARM: dts: ls1021a-tqmals1021a: Add overlay for CDTech FC21 RGB displayAlexander Stein
This adds an overlay for the supported RGB display CDTech FC21. DCU graphics chain is configured accordingly. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-23ARM: dts: ls1021a-tqmals1021a: Add LVDS overlay for Tianma TM070JVGH33Alexander Stein
This adds an overlay for the supported LVDS display tianma tm070jvhg33. The on-board RGB-to-LVDS encoder and DCU graphics chain are configured accordingly. Add power supply as well, which had been missing all the time. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
generated by cgit (git 2.34.1) at 2025-07-16 02:08:55 +0000