| Age | Commit message (Collapse) | Author |
|---|
|
During kernel init, the AM3505/AM3517 UART4 cannot complete its softreset:
omap_hwmod: uart4: softreset failed (waited 10000 usec)
This also results in another warning later in the boot process:
omap_hwmod: uart4: enabled state can only be entered from initialized, idle, or disabled state
From empirical observation, the AM35xx UART4 IP block requires either
uart1_fck or uart2_fck to be enabled while UART4 resets. Otherwise
the reset will never complete. So this patch adds uart1_fck as an
optional clock for UART4 and adds the appropriate hwmod flag to cause
uart1_fck to be enabled during the reset process. (The choice of
uart1_fck over uart2_fck was arbitrary.)
Unfortunately this observation raises many questions. Is it necessary
for uart1_fck or uart2_fck to be controlled with uart4_fck for the
UART4 to work correctly? What exactly do the AM35xx UART4 clock
tree and the related PRCM idle management FSMs look like? If anyone
has the ability to answer these questions through empirical functional
testing, or hardware information from the AM35xx designers, it would
be greatly appreciated.
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kyle Manna <kyle.manna@fuel7.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
|
|
Add missing terminators to the arrays of IRQ, DMA, and address space
structure records in the AM35xx UART4 hwmod data. Without these
terminators, the following warnings appear on boot:
omap_uart.3: failed to claim resource 58
omap_device: omap_uart: build failed (-16)
WARNING: at /home/paul/linux/arch/arm/mach-omap2/serial.c:375 omap_serial_init_port+0x198/0x284()
Could not build omap_device for omap_uart: uart4.
Also, AM35xx uart4_fck has an incorrect parent clock pointer. Fix it
and clean up a whitespace issue.
Fix some incorrectly-named macros related to AM35xx UART4.
Cc: Kyle Manna <kyle.manna@fuel7.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
|
|
Partially fix the hwmod data for the AM35xx USB OTG hwmod. This
should resolve the following boot warning on AM35xx platforms:
omap_hwmod: am35x_otg_hs: cannot be enabled for reset (3)
While here, also fix the clkdev records, to avoid warnings about
duplicate clock aliases.
The hwmod is also connected to the wrong interconnect. It should be
connected to the IPSS, not the L4 CORE. But that is left for a future
fix, since it probably has a dependency on some hwmod core changes.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Hema HK <hemahk@ti.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
|
|
OMAP4470 currently fails to boot, printing various messages such as ...
omap_hwmod: mpu: cannot clk_get main_clk dpll_mpu_m2_ck
omap_hwmod: mpu: cannot _init_clocks
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:2062 _init+0x2a0/0x2e4()
omap_hwmod: mpu: couldn't init clocks
Modules linked in:
[<c001c7fc>] (unwind_backtrace+0x0/0xf4) from [<c0043c64>] (warn_slowpath_common+0x4c/0x64)
[<c0043c64>] (warn_slowpath_common+0x4c/0x64) from [<c0043d10>] (warn_slowpath_fmt+0x30/0x40)
[<c0043d10>] (warn_slowpath_fmt+0x30/0x40) from [<c0674208>] (_init+0x2a0/0x2e4)
[<c0674208>] (_init+0x2a0/0x2e4) from [<c067428c>] (omap_hwmod_setup_one+0x40/0x60)
[<c067428c>] (omap_hwmod_setup_one+0x40/0x60) from [<c0674280>] (omap_hwmod_setup_one+0x34/0x60)
[<c0674280>] (omap_hwmod_setup_one+0x34/0x60) from [<c06726f4>] (omap_dm_timer_init_one+0x30/0x250)
[<c06726f4>] (omap_dm_timer_init_one+0x30/0x250) from [<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108)
[<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108) from [<c0672c60>] (omap4_timer_init+0x10/0x5c)
[<c0672c60>] (omap4_timer_init+0x10/0x5c) from [<c066c418>] (time_init+0x20/0x30)
[<c066c418>] (time_init+0x20/0x30) from [<c0668814>] (start_kernel+0x1b0/0x304)
[<c0668814>] (start_kernel+0x1b0/0x304) from [<80008044>] (0x80008044)
---[ end trace 1b75b31a2719ed1c ]---
The problem is that currently none of the clocks are being registered for
OMAP4470 devices and so on boot-up no clocks can be found and the kernel panics.
This fix allows the kernel to boot without failure using a simple RAMDISK file
system on OMAP4470 blaze board.
Per feedback from Paul and Benoit the 4470 clock data is incomplete for new
modules such as the 2D graphics block that has been added to the 4470.
Therefore add a warning to indicate that the clock data is incomplete.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP3, OMAP4 and AM33xx share some common data like, clksel_rate
oscillator clock input (Virtual clock nodes), required for
clock tree; so move common data to common data file so that it
can be reused.
[hvaibhav@ti.com: Created separate commit from Paul's developement
branch]
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
an oops on boot for all omap3xxx platforms that use usbhs_omap for
EHCI. The actual oops comes from faulty ehci-omap cleanup, but the
failure caused by the change is evidenced here:
[ 3.655059] ehci-omap ehci-omap.0: utmi_p1_gfclk failed error:-2
[ 3.661376] ehci-omap: probe of ehci-omap.0 failed with error -2
utmi_p1_gfclk is a clock that exists on OMAP4, but not OMAP3. In the
OMAP3 case, it is configured as a dummy clock. However, OMAP4 lists
the dev_id as NULL, but OMAP3 lists it as "usbhs_omap".
Attempting to get that clock from ehci-omap then fails. The solution
is to just change the clock3xxx_data.c for dummy clocks used in the
errata fix to match the dev_id, NULL, used in clock44xx_data.c.
Tested on BB-xM.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into devel-driver
|
|
commit 8259573b (ARM: OMAP2+: nand: Make board_onenand_init() visible
to board code) broke the build for configs with OneNAND disabled. By
removing the static in the header file, it created a duplicate definition
in the .c and the .h files, resuling in a build error:
/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.c:102:111: error: redefinition of 'board_onenand_init'
/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.h:56:51: note: previous definition of 'board_onenand_init' was here
make[2]: *** [arch/arm/mach-omap2/board-flash.o] Error 1
make[2]: *** Waiting for unfinished jobs....
make[1]: *** [arch/arm/mach-omap2] Error 2
make: *** [sub-make] Error 2
Fix this by removing the duplicate dummy entry from the C file.
Cc: Enric Balletbò i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This allows us to pass dma request lines in platform data to
MMC driver the same way as we already do for omap2430 and later.
Also note that we need to only build this code if MMC_OMAP
is selected, so change Makefile accordingly and place it near
the MMC_OMAP_HS in the Makefile.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For a power domain to idle all the clock domains in it must idle.
This patch implements an optimization of the cpuidle code by
denying and later allowing only the first registered clock domain
of a power domain, and so optimizes the latency of the low power code.
The functions _cpuidle_allow_idle and _cpuidle_deny_idle are
not used anymore and so are removed.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
One of the main contributors of the low power code latency is
the PER power domain. To optimize the high-performance and
low-latency C1 state, prevent any PER state which is lower
than the CORE state in C1.
Reported and suggested by Kevin Hilman.
Reported-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
If the next state is no found in the next_valid_state function,
fallback to the default value of C1 (which is state 0).
This prevents the use of a bogus state -1 in the rest of the cpuidle
code.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
commit e7410cf7 (OMAP3: PM: move device-specific special cases from PM
core into CPUidle) moved mangement of cam_pwrdm to CPUidle but left
some remnants behind, namely the call to clkcm_allo_idle() for the
clockdomains in the MPU pwrdm. Remove these since they are not
necessary and cause unwanted latency in the idle path.
Acked-by: Tero Kristo <Tero Kristo <t-kristo@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
We only need to call the pre/post transtion methods when we know the
power state is changing. First, split up the pre/post transition
calls to be per-powerdomain, and then make them conditional on whether
the power domain is actually changing states.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Iteration over all power domains in the idle path is unnecessary since
only power domains that are transitioning need to be accounted for.
Also PRCM register accesses are known to be expensive, so the
additional latency added to the idle path is signficiant.
In order allow the pre/post transitions to be isolated and called
per-pwrdm, change the API so passing in a specific power domain will
trigger the pre/post transtion accounting for only that specific power
domain. Passing NULL means iterating over all power domains as is
current behavior.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-pm
Reimplement the OMAP PRCM I/O chain code. Needed for I/O wakeups to
work correctly.
Conflicts:
arch/arm/mach-omap2/prm2xxx_3xxx.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into devel-driver
Convert the OMAP HDQ1W driver to use runtime PM. Make it available on
all OMAP2+ chips that appear to have it integrated. Fix a problem
preventing it from being used on OMAP4.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley (as per Tony Lindgren's request):
"Some uncontroversial OMAP clock, hwmod, and compiler warning fixes for 3.5-rc"
* tag 'omap-fixes-a-for-3.5rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
ARM: OMAP2+: mux: fix sparse warning
ARM: OMAP2+: CM: increase the module disable timeout
ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
ARM: OMAP: PM: Lock clocks list while generating summary
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"Here are a few fixes with the biggest one being fix for Beagle DVI
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier."
* tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
|
|
As IO Daisy chain sequence is triggered via hwmod mux, there is no need to
control it from cpuidle path for OMAP3.
Also as omap3_disable_io_chain is no longer being used, just remove the
function.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
IO Daisychain feature has to be triggered whenever there is a change in
device's mux configuration (See section 3.9.4 in OMAP4 Public TRM vP).
Now devices can idle independent of the powerdomain, there can be a
window where device is idled and corresponding powerdomain can be
ON/INACTIVE state. In such situations, since both module wake up is
enabled at padlevel as well as io daisychain sequence is triggered,
there will be 2 PRCM interrupts (Module async wake up via swakeup and
IO Pad interrupt). But as PRCM Interrupt handler clears the Module
Padlevel WKST bit in the first interrupt, module specific interrupt
handler will not triggered for the second time
Also look at detailed explanation given by Rajendra at
http://www.spinics.net/lists/linux-serial/msg04480.html
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: remove dependency on pm.c & pm.h; add kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Enable IO Wake up for OMAP3/4 as part of PRM Init. Currently this has been
managed in cpuidle path which is not the right place. Subsequent patch
will remove IO Daisy chain handling in cpuidle path once daisy chain is
handled as part of hwmod mux. This patch also moves the OMAP4 IO wakeup
enable code from the trigger function to init time setup.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: harmonize function names with other PRM functions; add
kerneldoc; resolve checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
IO daisychain is a mechanism that allows individual IO pads to generate
wakeup events on their own based on a switch of an input signal level.
This allows the hardware module behind the pad to be powered down, but
still have device level capability to detect IO events, and once this
happens the module can be powered back up to resume IO. See section
3.9.4 in OMAP4430 Public TRM for details.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: use the shared MAX_IOPAD_LATCH_TIME declaration; renamed
omap4_trigger_io_chain() to conform to other PRM function names;
added kerneldoc; resolved checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Since IO Daisychain modifies only PRM registers, it makes sense to move
it to PRM File. Also changed the timeout value for IO chain enable to
100us and added a wait for status disable at the end.
Thanks to Nishanth Menon <nm@ti.com> for contributing a fix to the
timeout code waiting for WUCLKOUT to go high.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: renamed omap3_trigger_io_chain() to better describe the
end result and to match other PRM functions; removed
omap3_disable_io_chain(); moved MAX_IOPAD_LATCH_TIME to prcm-common as it
will also be used by the OMAP4 code; removed unnecessary barrier;
added kerneldoc; added credit for fix from Nishanth]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Currently the enabling and disabling of IO Daisy chain is not
according to the TRM. The below steps are followed to enable/
disable the IO chain, based loosely on the "Sec 3.5.7.2.2
I/O Wake-Up Mechanism" section in OMAP3630 Public TRM[1].
Steps to enable IO chain:
[a] Set PM_WKEN_WKUP.EN_IO bit
[b] Set the PM_WKEN_WKUP.EN_IO_CHAIN bit
[c] Poll for PM_WKST_WKUP.ST_IO_CHAIN.
[d] When ST_IO_CHAIN bit set to 1, clear PM_WKEN_WKUP.EN_IO_CHAIN
[e] Clear ST_IO_CHAIN bit.
Steps to disable IO chain:
[a] Clear PM_WKEN_WKUP.EN_IO_CHAIN bit
[b] Clear PM_WKEN_WKUP.EN_IO bit
[c] Clear PM_WKST_WKUP.ST_IO bit by writing 1 to it.
Step [e] & [c] in each case can be skipped, as these are handled
by the PRCM interrupt handler later.
[1] http://focus.ti.com/pdfs/wtbu/OMAP36xx_ES1.x_PUBLIC_TRM_vV.zip
Signed-off-by: Mohan V <mohanv@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[paul@pwsan.com: modified commit message to clarify that these steps are
based loosely on the TRM section, rather than documented exactly]
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: resolved new warnings from checkpatch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
For OMAP4 only builds, the omap2_prm_* functions have dummy wrappers
to detect incorrect usage. However, several unrelated omap3 PRM
functions have made it inside the #else clause of the #ifdef wrapping
the omap2_prm stubs, causing them to disappear on OMAP4-only builds.
This was unnoticed until the IO chain support was added and introduced
a new function in this section which is referenced by omap_hwmod.c:
arch/arm/mach-omap2/omap_hwmod.c: In function '_reconfigure_io_chain':
arch/arm/mach-omap2/omap_hwmod.c:1665:3: error: implicit declaration of function 'omap3xxx_prm_reconfigure_io_chain' [-Werror=implicit-function-declaration]
Fix by using the #ifdef to only wrap the omap2_prm functions that
need stubs on OMAP4-only builds.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: fixed checkpatch warnings for patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Convert the old-style device registration code for HDQ1W to use
omap_device. This will allow the driver to be converted to use PM
runtime and to take advantage of the OMAP IP block management
infrastructure (hwmod, PM, etc.).
A side benefit of this conversion is that it also makes the HDQ device
available on OMAP2420. The previous code only enabled it on 2430 and
3430.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
|
|
As per the OMAP4 documentation, audio over HDMI must be transmitted in
no-idle mode. This patch adds the HWMOD_SWSUP_SIDLE so that omap_hwmod uses
no-idle/force-idle settings instead of smart-idle mode.
This is required as the DSS interface clock is used as functional clock
for the HDMI wrapper audio FIFO. If no-idle mode is not used, audio could
be choppy, have bad quality or not be audible at all.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
[b-cousson@ti.com: Update the subject and align the .flags
location with the script template]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit bbd707acee279a61177a604822db92e8164d00db ("ARM: omap2: use
machine specific hook for late init") resulted in the addition of this
sparse warning:
arch/arm/mach-omap2/mux.c:791:12: warning: symbol 'omap_mux_late_init' was not declared. Should it be static?
Fix by including the header file containing the prototype.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
|
|
Increase the timeout for disabling an IP block to five milliseconds.
This is to handle the usb_host_fs idle latency, which takes almost
four milliseconds after a host controller reset.
This is the second of two patches needed to resolve the following
boot warning:
omap_hwmod: usb_host_fs: _wait_target_disable failed
Thanks to Sergei Shtylyov <sshtylyov@mvista.com> for finding
an unrelated hunk in a previous version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Tero Kristo <t-kristo@ti.com>
|
|
Until the OMAP4 code is converted to disable the use of the clock
framework-based clockdomain enable/disable sequence, any clock used as
a hwmod main_clk must have a clockdomain associated with it. This
patch populates some clock structure clockdomain names to resolve the
following warnings during kernel init:
omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
omap_hwmod: trace_clk_div_ck: missing clockdomain for trace_clk_div_ck.
omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
omap_hwmod: ddrphy_ck: missing clockdomain for ddrphy_ck.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
The 32k sync timer IP block target idle modes in the hwmod data are
incorrect. The IP block does not support any smart-idle modes.
Update the data to reflect the correct modes.
This problem was initially identified and a diff fragment posted to
the lists by Benoît Cousson <b-cousson@ti.com>. A patch description
bug in the first version was also identified by Benoît.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
|
|
If an IP is configured in Smart-Standby-Wakeup, when disabling wakeup feature the
IP will not go back to Smart-Standby, but will remain in Smart-Standby-Wakeup.
Signed-off-by: Djamil Elaidi <d-elaidi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The beagleboard USB Host Port that is used is Port 2. The platform driver
sets MODE_PHY for port 1 causing pin muxing to override the pins on the
expansion connector P17 when using board_mux[]. Since USBHS Port 1 is not
connected remove the case for muxing the USB Port1 pins by default.
Tested with BeagleBoard xM revC and checked the userguides for Beagle xM
and revC to be sure USB Port2 is what is used.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If the kernel is built only for OMAP2 the following warning will show up:
arch/arm/mach-omap2/twl-common.c:52: warning: ‘twl_set_voltage’ defined but not used
arch/arm/mach-omap2/twl-common.c:58: warning: ‘twl_get_voltage’ defined but not used
The twl_set/get_voltage callbacks only used when OMAP3/4 is selected.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
In case a board provides the gpio_pendown and not board_pdata,
the GPIO debounce is not taken care of.
Fix this by taking care of GPIO debounce in any case.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
'control_clean_dspbridge_writes_cleanup_3.6', 'hwmod_soc_conditional_cleanup_3.6', 'mcbsp_clock_aliases_cleanup_3.6' and 'remove_clkdm_requirement_from_hwmod_3.6' into omap_cleanup_a_3.6
Conflicts:
arch/arm/mach-omap2/omap_hwmod.c
|
|
Commit e813a55eb9c9bc6c8039fb16332cf43402125b30 ("OMAP: board-files:
remove custom PD GPIO handling for DVI output") moved TFP410 chip's
powerdown-gpio handling from the board files to the tfp410 driver. One
gpio_request_one(powerdown-gpio, ...) was mistakenly left unremoved in
the Beagle board file. This causes the tfp410 driver to fail to request
the gpio on Beagle, causing the driver to fail and thus the DVI output
doesn't work.
This patch removes several boot errors from board-omap3beagle.c:
- gpio_request: gpio--22 (DVI reset) status -22
- Unable to get DVI reset GPIO
There is a combination of leftover code and revision confusion.
Additionally, xM support is currently a hack.
For original Beagleboard this removes the double initialization of GPIO
170, properly configures it as an output, and wraps the initialization
in an if block so that xM does not attempt to request it.
For Beagleboard xM it removes reference to GPIO 129 which was part
of rev A1 and A2 designs, but never functioned. It then properly assigns
beagle_dvi_device.reset_gpio in beagle_twl_gpio_setup and removes the
hack of initializing it high. Additionally, it uses
gpio_set_value_cansleep since this GPIO is connected through i2c.
Unfortunately, there is no way to tell the difference between xM A2 and
A3. However, GPIO 129 does not function on rev A1 and A2, and the TWL
GPIO used on A3 and beyond is not used on rev A1 and A2, there are no
problems created by this fix.
Tested on Beagleboard-xM Rev C1 and Beagleboard Rev B4.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Here's one more gpio_to_irq conversion that we missed
earlier. Tested with n800 in gadget mode using USB_ETH.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 62285963 (usb: musb: drop a gigantic amount of ifdeferry)
got rid of a bunch of ifdefs in the MUSB code. Looks like the
platform init code is still using these dropped defines though,
which in many cases results the board defaulting always to host
mode.
Currently the situation is that USB_MUSB_HDRC is the main
Kconfig option with additional USB_GADGET_MUSB_HDRC so only
these two should be used to select between host and OTG mode.
Fix the situation for omaps. The following users should fix the
platform init code in a similar way:
Dropped Kconfig option Current users
USB_MUSB_OTG blackfin, davinci, not in Kconfigs
USB_MUSB_PERIPHERAL davinci, not in Kconfigs
USB_MUSB_HOST davinci, not in Kconfigs
USB_MUSB_HDRC_HCD blackfin, not in Kconfigs
USB_MUSB_OTG blackfin, not in Kconfigs
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The TWL driver has been converted to use SPARSE_IRQ and no longer
needs to be passed IRQ base/end. Since driver no longer uses these
fields, so remove them from the reamaining users.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Commit 9fa2df6b90786301b175e264f5fa9846aba81a65
(ARM: OMAP2+: OPP: allow OPP enumeration to continue if device is not present)
makes the logic:
for (i = 0; i < opp_def_size; i++) {
<snip>
if (!oh || !oh->od) {
<snip>
continue;
}
<snip>
opp_def++;
}
In short, the moment we hit a "Bad OPP", we end up looping the list
comparing against the bad opp definition pointer for the rest of the
iteration count. Instead, increment opp_def in the for loop itself
and allow continue to be used in code without much thought so that
we check the next set of OPP definition pointers :)
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
The current Makefile compiles the cpuidle34xx.c and cpuidle44xx.c files
even if the cpuidle option is not set in the kernel.
This patch fixes this by creating a section in the Makefile where these
files are compiled only if the CONFIG_CPU_IDLE option is set.
This modification breaks an implicit dependency between CPU_IDLE and PM as
they belong to the same block in the Makefile. This is fixed in the Kconfig
by selecting explicitely PM is CPU_IDLE is set.
The linux coding style recommend to use no-op functions in the headers
when the subsystem is disabled instead of adding big section in C files.
This patch fix this also.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
prcm_setup_regs() blindly accesses IVA bits
in the PRM and calls omap3_iva_idle() which
does more IVA related register accesses.
Only do this if the IVA hardware actually
exists.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
clockdomain
Remove prm_clkdm and cm_clkdm and allow hwmods to have no clockdomain.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
Remove the existing alias for pad_fck, prcm_fck from the clock data and
add them as opt_clks to the hwmod data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Remove the existing alias for pad_fck, prcm_fck from the clock data and
add them as opt_clks to the hwmod data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Remove the existing alias for pad_fck, prcm_fck from the clock data and
add them as opt_clks to the hwmod data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Provide an interface for a driver to call SCM functions to
set a boot address and boot mode.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
SCM contains boot addr and boot mode registers to control
other processors on different OMAP versions. It controls the
boot address and mode for DSP based subsystems like: IVA 2.1
(OMAP2430), IVA 2.2 (OMAP3) and DSP (OMAP4).
If contained within SCM registers, when a processor is
booting it uses BOOTADDR to start running the code at that
location. BOOTMOD register specifies a different set of
modes for the processor to execute when booting (from direct,
idle, self-loop, user and default).
Since there was no offset associated with OMAP4, this patch
defines it.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
