summaryrefslogtreecommitdiff
path: root/drivers/bluetooth
AgeCommit message (Collapse)Author
2023-12-22Bluetooth: Add device 13d3:3572 IMC Networks Bluetooth RadioJagan Teki
This 13d3:3572 is part of Realtek RTW8852BE chip. The device table is: T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3572 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Jagan Teki <jagan@edgeble.ai> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-12-22Bluetooth: btnxpuart: remove useless assignmentFrancesco Dolcini
Remove useless assignment of rx_skb to NULL in case the skb is in error, this is already done in h4_recv_buf() that is executed a few lines before. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-12-22Bluetooth: btmtkuart: fix recv_buf() return valueFrancesco Dolcini
Serdev recv_buf() callback is supposed to return the amount of bytes consumed, therefore an int in between 0 and count. Do not return negative number in case of issue, just print an error and return count. This fixes a WARN in ttyport_receive_buf(). Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/ Fixes: 7237c4c9ec92 ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices") Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-12-22Bluetooth: btnxpuart: fix recv_buf() return valueFrancesco Dolcini
Serdev recv_buf() callback is supposed to return the amount of bytes consumed, therefore an int in between 0 and count. Do not return a negative number in case of issue, just print an error and return count. Before this change, in case of error, the returned negative number was internally converted to 0 in ttyport_receive_buf, now when the receive buffer is corrupted we return the size of the whole received data (`count`). This should allow for better recovery in case receiver/transmitter get out of sync if some data is lost. This fixes a WARN in ttyport_receive_buf(). Bluetooth: hci0: Frame reassembly failed (-84) ------------[ cut here ]------------ serial serial0: receive_buf returns -84 (count = 6) WARNING: CPU: 0 PID: 37 at drivers/tty/serdev/serdev-ttyport.c:37 ttyport_receive_buf+0xd8/0xf8 Modules linked in: mwifiex_sdio(+) ... CPU: 0 PID: 37 Comm: kworker/u4:2 Not tainted 6.7.0-rc2-00147-gf1a09972a45a #1 Hardware name: Toradex Verdin AM62 WB on Verdin Development Board (DT) Workqueue: events_unbound flush_to_ldisc pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : ttyport_receive_buf+0xd8/0xf8 lr : ttyport_receive_buf+0xd8/0xf8 ... Call trace: ttyport_receive_buf+0xd8/0xf8 flush_to_ldisc+0xbc/0x1a4 process_scheduled_works+0x16c/0x28c Closes: https://lore.kernel.org/all/ZWEIhcUXfutb5SY6@francesco-nb.int.toradex.com/ Fixes: 689ca16e5232 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets") Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-12-22Bluetooth: qca: Support HFP offload for QCA2066Zijun Hu
For QCA2066 HFP offload, HCI_Configure_Data_Path is not required since present HCI_Enhanced_Setup_Synchronous_Connection is enough to configure non-HCI data transport path when set both Input_Data_Path and Output_Data_Path parameters as 0x01, as is implemented by this change. Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-12-22Bluetooth: btintel: Print firmware SHA1Kiran K
Intel Read Version event contains a TLV(0x32) having firmware sha1 in operational image. Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-12-22Bluetooth: btusb: Don't suspend when there are connectionsLuiz Augusto von Dentz
This checks if there are connections before suspending since that may disrupt the connections making it stop receiving any data if remote wakeup is not enabled. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-12-22Bluetooth: qca: Set both WIDEBAND_SPEECH and LE_STATES quirks for QCA2066Zijun Hu
Set both WIDEBAND_SPEECH_SUPPORTED and VALID_LE_STATES quirks for QCA2066. Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-12-15Bluetooth: Fix deadlock in vhci_send_frameYing Hsu
syzbot found a potential circular dependency leading to a deadlock: -> #3 (&hdev->req_lock){+.+.}-{3:3}: __mutex_lock_common+0x1b6/0x1bc2 kernel/locking/mutex.c:599 __mutex_lock kernel/locking/mutex.c:732 [inline] mutex_lock_nested+0x17/0x1c kernel/locking/mutex.c:784 hci_dev_do_close+0x3f/0x9f net/bluetooth/hci_core.c:551 hci_rfkill_set_block+0x130/0x1ac net/bluetooth/hci_core.c:935 rfkill_set_block+0x1e6/0x3b8 net/rfkill/core.c:345 rfkill_fop_write+0x2d8/0x672 net/rfkill/core.c:1274 vfs_write+0x277/0xcf5 fs/read_write.c:594 ksys_write+0x19b/0x2bd fs/read_write.c:650 do_syscall_x64 arch/x86/entry/common.c:55 [inline] do_syscall_64+0x51/0xba arch/x86/entry/common.c:93 entry_SYSCALL_64_after_hwframe+0x61/0xcb -> #2 (rfkill_global_mutex){+.+.}-{3:3}: __mutex_lock_common+0x1b6/0x1bc2 kernel/locking/mutex.c:599 __mutex_lock kernel/locking/mutex.c:732 [inline] mutex_lock_nested+0x17/0x1c kernel/locking/mutex.c:784 rfkill_register+0x30/0x7e3 net/rfkill/core.c:1045 hci_register_dev+0x48f/0x96d net/bluetooth/hci_core.c:2622 __vhci_create_device drivers/bluetooth/hci_vhci.c:341 [inline] vhci_create_device+0x3ad/0x68f drivers/bluetooth/hci_vhci.c:374 vhci_get_user drivers/bluetooth/hci_vhci.c:431 [inline] vhci_write+0x37b/0x429 drivers/bluetooth/hci_vhci.c:511 call_write_iter include/linux/fs.h:2109 [inline] new_sync_write fs/read_write.c:509 [inline] vfs_write+0xaa8/0xcf5 fs/read_write.c:596 ksys_write+0x19b/0x2bd fs/read_write.c:650 do_syscall_x64 arch/x86/entry/common.c:55 [inline] do_syscall_64+0x51/0xba arch/x86/entry/common.c:93 entry_SYSCALL_64_after_hwframe+0x61/0xcb -> #1 (&data->open_mutex){+.+.}-{3:3}: __mutex_lock_common+0x1b6/0x1bc2 kernel/locking/mutex.c:599 __mutex_lock kernel/locking/mutex.c:732 [inline] mutex_lock_nested+0x17/0x1c kernel/locking/mutex.c:784 vhci_send_frame+0x68/0x9c drivers/bluetooth/hci_vhci.c:75 hci_send_frame+0x1cc/0x2ff net/bluetooth/hci_core.c:2989 hci_sched_acl_pkt net/bluetooth/hci_core.c:3498 [inline] hci_sched_acl net/bluetooth/hci_core.c:3583 [inline] hci_tx_work+0xb94/0x1a60 net/bluetooth/hci_core.c:3654 process_one_work+0x901/0xfb8 kernel/workqueue.c:2310 worker_thread+0xa67/0x1003 kernel/workqueue.c:2457 kthread+0x36a/0x430 kernel/kthread.c:319 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:298 -> #0 ((work_completion)(&hdev->tx_work)){+.+.}-{0:0}: check_prev_add kernel/locking/lockdep.c:3053 [inline] check_prevs_add kernel/locking/lockdep.c:3172 [inline] validate_chain kernel/locking/lockdep.c:3787 [inline] __lock_acquire+0x2d32/0x77fa kernel/locking/lockdep.c:5011 lock_acquire+0x273/0x4d5 kernel/locking/lockdep.c:5622 __flush_work+0xee/0x19f kernel/workqueue.c:3090 hci_dev_close_sync+0x32f/0x1113 net/bluetooth/hci_sync.c:4352 hci_dev_do_close+0x47/0x9f net/bluetooth/hci_core.c:553 hci_rfkill_set_block+0x130/0x1ac net/bluetooth/hci_core.c:935 rfkill_set_block+0x1e6/0x3b8 net/rfkill/core.c:345 rfkill_fop_write+0x2d8/0x672 net/rfkill/core.c:1274 vfs_write+0x277/0xcf5 fs/read_write.c:594 ksys_write+0x19b/0x2bd fs/read_write.c:650 do_syscall_x64 arch/x86/entry/common.c:55 [inline] do_syscall_64+0x51/0xba arch/x86/entry/common.c:93 entry_SYSCALL_64_after_hwframe+0x61/0xcb This change removes the need for acquiring the open_mutex in vhci_send_frame, thus eliminating the potential deadlock while maintaining the required packet ordering. Fixes: 92d4abd66f70 ("Bluetooth: vhci: Fix race when opening vhci device") Signed-off-by: Ying Hsu <yinghsu@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-12-08tty: serdev: convert to u8 and size_tJiri Slaby (SUSE)
Switch character types to u8 and sizes to size_t. To conform to characters/sizes in the rest of the tty layer. This patch converts struct serdev_device_ops hooks and its instantiations. Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org> Cc: Rob Herring <robh@kernel.org> Acked-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20231206073712.17776-24-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-10-23Bluetooth: btmtksdio: enable bluetooth wakeup in system suspendZhengping Jiang
The BTMTKSDIO_BT_WAKE_ENABLED flag is set for bluetooth interrupt during system suspend and increases wakeup count for bluetooth event. Signed-off-by: Zhengping Jiang <jiangzp@google.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-10-23Bluetooth: btusb: Add 0bda:b85b for Fn-Link RTL8852BEGuan Wentao
Add PID/VID 0bda:b85b for Realtek RTL8852BE USB bluetooth part. The PID/VID was reported by the patch last year. [1] Some SBCs like rockpi 5B A8 module contains the device. And it`s founded in website. [2] [3] Here is the device tables in /sys/kernel/debug/usb/devices . T: Bus=07 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=b85b Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Link: https://lore.kernel.org/all/20220420052402.19049-1-tangmeng@uniontech.com/ [1] Link: https://forum.radxa.com/t/bluetooth-on-ubuntu/13051/4 [2] Link: https://ubuntuforums.org/showthread.php?t=2489527 [3] Cc: stable@vger.kernel.org Signed-off-by: Meng Tang <tangmeng@uniontech.com> Signed-off-by: Guan Wentao <guanwentao@uniontech.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-10-23Bluetooth: hci_bcm4377: Mark bcm4378/bcm4387 as BROKEN_LE_CODEDJanne Grunau
bcm4378 and bcm4387 claim to support LE Coded PHY but fail to pair (reliably) with BLE devices if it is enabled. On bcm4378 pairing usually succeeds after 2-3 tries. On bcm4387 pairing appears to be completely broken. Cc: stable@vger.kernel.org # 6.4.y+ Link: https://discussion.fedoraproject.org/t/mx-master-3-bluetooth-mouse-doesnt-connect/87072/33 Link: https://github.com/AsahiLinux/linux/issues/177 Fixes: 288c90224eec ("Bluetooth: Enable all supported LE PHY by default") Signed-off-by: Janne Grunau <j@jannau.net> Reviewed-by: Eric Curtin <ecurtin@redhat.com> Reviewed-by: Neal Gompa <neal@gompa.dev> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-10-23Bluetooth: btusb: Add date->evt_skb is NULL checkyouwan Wang
fix crash because of null pointers [ 6104.969662] BUG: kernel NULL pointer dereference, address: 00000000000000c8 [ 6104.969667] #PF: supervisor read access in kernel mode [ 6104.969668] #PF: error_code(0x0000) - not-present page [ 6104.969670] PGD 0 P4D 0 [ 6104.969673] Oops: 0000 [#1] SMP NOPTI [ 6104.969684] RIP: 0010:btusb_mtk_hci_wmt_sync+0x144/0x220 [btusb] [ 6104.969688] RSP: 0018:ffffb8d681533d48 EFLAGS: 00010246 [ 6104.969689] RAX: 0000000000000000 RBX: ffff8ad560bb2000 RCX: 0000000000000006 [ 6104.969691] RDX: 0000000000000000 RSI: ffffb8d681533d08 RDI: 0000000000000000 [ 6104.969692] RBP: ffffb8d681533d70 R08: 0000000000000001 R09: 0000000000000001 [ 6104.969694] R10: 0000000000000001 R11: 00000000fa83b2da R12: ffff8ad461d1d7c0 [ 6104.969695] R13: 0000000000000000 R14: ffff8ad459618c18 R15: ffffb8d681533d90 [ 6104.969697] FS: 00007f5a1cab9d40(0000) GS:ffff8ad578200000(0000) knlGS:00000 [ 6104.969699] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 6104.969700] CR2: 00000000000000c8 CR3: 000000018620c001 CR4: 0000000000760ef0 [ 6104.969701] PKRU: 55555554 [ 6104.969702] Call Trace: [ 6104.969708] btusb_mtk_shutdown+0x44/0x80 [btusb] [ 6104.969732] hci_dev_do_close+0x470/0x5c0 [bluetooth] [ 6104.969748] hci_rfkill_set_block+0x56/0xa0 [bluetooth] [ 6104.969753] rfkill_set_block+0x92/0x160 [ 6104.969755] rfkill_fop_write+0x136/0x1e0 [ 6104.969759] __vfs_write+0x18/0x40 [ 6104.969761] vfs_write+0xdf/0x1c0 [ 6104.969763] ksys_write+0xb1/0xe0 [ 6104.969765] __x64_sys_write+0x1a/0x20 [ 6104.969769] do_syscall_64+0x51/0x180 [ 6104.969771] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 6104.969773] RIP: 0033:0x7f5a21f18fef [ 6104.9] RSP: 002b:00007ffeefe39010 EFLAGS: 00000293 ORIG_RAX: 0000000000000001 [ 6104.969780] RAX: ffffffffffffffda RBX: 000055c10a7560a0 RCX: 00007f5a21f18fef [ 6104.969781] RDX: 0000000000000008 RSI: 00007ffeefe39060 RDI: 0000000000000012 [ 6104.969782] RBP: 00007ffeefe39060 R08: 0000000000000000 R09: 0000000000000017 [ 6104.969784] R10: 00007ffeefe38d97 R11: 0000000000000293 R12: 0000000000000002 [ 6104.969785] R13: 00007ffeefe39220 R14: 00007ffeefe391a0 R15: 000055c10a72acf0 Signed-off-by: youwan Wang <wangyouwan@126.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-10-23Bluetooth: btusb: Add RTW8852BE device 13d3:3570 to device tablesMasum Reza
This device is used in TP-Link TX20E WiFi+Bluetooth adapter. Relevant information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3570 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Masum Reza <masumrezarock100@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-10-23Bluetooth: qca: add support for QCA2066Tim Jiang
This patch adds support for QCA2066 firmware patch and NVM downloading. as the RF performance of QCA2066 SOC chip from different foundries may vary. Therefore we use different NVM to configure them based on board ID. Changes in v2 - optimize the function qca_generate_hsp_nvm_name - remove redundant debug code for function qca_read_fw_board_id Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-10-23Bluetooth: Add support for Intel Misty Peak - 8087:0038Vijay Satija
Devices from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=01 Prnt=01 Port=13 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0038 Rev= 0.00 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Vijay Satija <vijay.satija@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-10-23Bluetooth: Add support ITTIM PE50-M75CJingyang Wang
-Device(35f5:7922) from /sys/kernel/debug/usb/devices P: Vendor=35f5 ProdID=7922 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Jingyang Wang <wjy7717@126.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-10-13Bluetooth: btrtl: Ignore error return for hci_devcd_register()Max Chou
If CONFIG_DEV_COREDUMP was not set, it would return -EOPNOTSUPP for hci_devcd_register(). In this commit, ignore error return for hci_devcd_register(). Otherwise Bluetooth initialization will be failed. Fixes: 044014ce85a1 ("Bluetooth: btrtl: Add Realtek devcoredump support") Cc: stable@vger.kernel.org Reported-by: Kirill A. Shutemov <kirill@shutemov.name> Closes: https://lore.kernel.org/all/ZRyqIn0_qqEFBPdy@debian.me/T/ Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-10-11Bluetooth: vhci: Fix race when opening vhci deviceArkadiusz Bokowy
When the vhci device is opened in the two-step way, i.e.: open device then write a vendor packet with requested controller type, the device shall respond with a vendor packet which includes HCI index of created interface. When the virtual HCI is created, the host sends a reset request to the controller. This request is processed by the vhci_send_frame() function. However, this request is send by a different thread, so it might happen that this HCI request will be received before the vendor response is queued in the read queue. This results in the HCI vendor response and HCI reset request inversion in the read queue which leads to improper behavior of btvirt: > dmesg [1754256.640122] Bluetooth: MGMT ver 1.22 [1754263.023806] Bluetooth: MGMT ver 1.22 [1754265.043775] Bluetooth: hci1: Opcode 0x c03 failed: -110 In order to synchronize vhci two-step open/setup process with virtual HCI initialization, this patch adds internal lock when queuing data in the vhci_send_frame() function. Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-09-20Bluetooth: btusb: add shutdown function for QCA6174Rocky Liao
We should send hci reset command before bt turn off, which can reset bt firmware status. Signed-off-by: Rocky Liao <quic_rjliao@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-09-01Merge tag 'tty-6.6-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver updates from Greg KH: "Here is the big set of tty and serial driver changes for 6.6-rc1. Lots of cleanups in here this cycle, and some driver updates. Short summary is: - Jiri's continued work to make the tty code and apis be a bit more sane with regards to modern kernel coding style and types - cpm_uart driver updates - n_gsm updates and fixes - meson driver updates - sc16is7xx driver updates - 8250 driver updates for different hardware types - qcom-geni driver fixes - tegra serial driver change - stm32 driver updates - synclink_gt driver cleanups - tty structure size reduction All of these have been in linux-next this week with no reported issues. The last bit of cleanups from Jiri and the tty structure size reduction came in last week, a bit late but as they were just style changes and size reductions, I figured they should get into this merge cycle so that others can work on top of them with no merge conflicts" * tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits) tty: shrink the size of struct tty_struct by 40 bytes tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw() tty: n_tty: extract ECHO_OP processing to a separate function tty: n_tty: unify counts to size_t tty: n_tty: use u8 for chars and flags tty: n_tty: simplify chars_in_buffer() tty: n_tty: remove unsigned char casts from character constants tty: n_tty: move newline handling to a separate function tty: n_tty: move canon handling to a separate function tty: n_tty: use MASK() for masking out size bits tty: n_tty: make n_tty_data::num_overrun unsigned tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun() tty: n_tty: use 'num' for writes' counts tty: n_tty: use output character directly tty: n_tty: make flow of n_tty_receive_buf_common() a bool Revert "tty: serial: meson: Add a earlycon for the T7 SoC" Documentation: devices.txt: Fix minors for ttyCPM* Documentation: devices.txt: Remove ttySIOC* Documentation: devices.txt: Remove ttyIOC* serial: 8250_bcm7271: improve bcm7271 8250 port ...
2023-08-24Bluetooth: btusb: Do not call kfree_skb() under spin_lock_irqsave()Jinjie Ruan
It is not allowed to call kfree_skb() from hardware interrupt context or with hardware interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile tested only. Fixes: baac6276c0a9 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints") Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-24Bluetooth: btusb: Fix quirks table namingBastien Nocera
The quirks table was named "blacklist_table" which isn't a good description for that table as devices detected using it weren't ignored by the driver. Rename the table to match what it actually does. Signed-off-by: Bastien Nocera <hadess@hadess.net> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-24Bluetooth: HCI: Introduce HCI_QUIRK_BROKEN_LE_CODEDLuiz Augusto von Dentz
This introduces HCI_QUIRK_BROKEN_LE_CODED which is used to indicate that LE Coded PHY shall not be used, it is then set for some Intel models that claim to support it but when used causes many problems. Cc: stable@vger.kernel.org # 6.4.y+ Link: https://github.com/bluez/bluez/issues/577 Link: https://github.com/bluez/bluez/issues/582 Link: https://lore.kernel.org/linux-bluetooth/CABBYNZKco-v7wkjHHexxQbgwwSz-S=GZ=dZKbRE1qxT1h4fFbQ@mail.gmail.com/T/# Fixes: 288c90224eec ("Bluetooth: Enable all supported LE PHY by default") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-24Bluetooth: btintel: Send new command for PPAGLokendra Singh
Added support for the new command opcode FE0B (HCI Intel PPAG Enable). btmon log: < HCI Command: Intel PPAG Enable (0x3f|0x020b) plen 4 Enable: 0x00000002 > HCI Event: Command Complete (0x0e) plen 4 Intel PPAG Enable (0x3f|0x020b) ncmd 1 Status: Success (0x00) Signed-off-by: Seema Sreemantha <seema.sreemantha@intel.com> Signed-off-by: Lokendra Singh <lokendra.singh@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-24Bluetooth: qca: add support for WCN7850Neil Armstrong
Add support for the WCN7850 Bluetooth chipset. Tested on the SM8550 QRD platform. Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-24Bluetooth: qca: use switch case for soc type behaviorNeil Armstrong
Use switch/case to handle soc type specific behaviour, the permit dropping the qca_is_xxx() inline functions and make the code clearer and easier to update for new SoCs. Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org> Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-24Bluetooth: btnxpuart: Improve inband Independent Reset handlingNeeraj Sanjay Kale
This improves the inband IR command handling for NXP BT chipsets. When the IR vendor command is received, the driver injects a HW error event, which causes a reset sequence in hci_error_reset(). The vendor IR command is sent to the controller while hci dev is been closed, and FW is re-downloaded when nxp_setup() is called during hci_dev_do_open(). The HCI_SETUP flag is set in nxp_hw_err() to make sure that nxp_setup() is been called during hci_dev_do_open(). This also makes the nxp_setup() and power save functions more generic. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-24Bluetooth: btnxpuart: Add support for IW624 chipsetNeeraj Sanjay Kale
This adds support for NXP IW624 chipset in btnxpuart driver by adding FW name and bootloader signature. Based on the loader version bits 7:6 of the bootloader signature, the driver can choose between selecting secure and non-secure FW files. For cmd5 payload during FW download, this chip has addresses of few registers offset by 1, so added boot_reg_offset to handle the chip specific offset. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-24Bluetooth: btnxpuart: Remove check for CTS low after FW downloadNeeraj Sanjay Kale
This removes the unnecessary check for CTS low after FW download. After FW download is complete, the CTS line is already seen low. It becomes high after 2 msec, and low again after FW initialization is complete. This makes the current check for CTS low redundant. This removes the wait for CTS low section and increase delay to 1200msec instead, which is sufficiant for all NXP chipsets to initialize FW. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11tty: ldops: unify to u8Jiri Slaby (SUSE)
Some hooks in struct tty_ldisc_ops still reference buffers by 'unsigned char'. Unify to 'u8' as the rest of the tty layer does. Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20230810091510.13006-32-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-08-11tty: use u8 for flagsJiri Slaby (SUSE)
This makes all those 'char's an explicit 'u8'. This is part of the continuing unification of chars and flags to be consistent u8. This approaches tty_port_default_receive_buf(). Note that we do not change signedness as we compile with -funsigned-char. Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org> Cc: William Hubbs <w.d.hubbs@gmail.com> Cc: Chris Brannon <chris@the-brannons.com> Cc: Kirk Reiser <kirk@reisers.ca> Cc: Samuel Thibault <samuel.thibault@ens-lyon.org> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Max Staudt <max@enpas.org> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com> Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de> Cc: Jeremy Kerr <jk@codeconstruct.com.au> Cc: Matt Johnston <matt@codeconstruct.com.au> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20230810091510.13006-18-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-08-11tty: make tty_ldisc_ops::*buf*() hooks operate on size_tJiri Slaby (SUSE)
Count passed to tty_ldisc_ops::receive_buf*(), ::lookahead_buf(), and returned from ::receive_buf2() is expected to be size_t. So set it to size_t to unify with the rest of the code. Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org> Cc: William Hubbs <w.d.hubbs@gmail.com> Cc: Chris Brannon <chris@the-brannons.com> Cc: Kirk Reiser <kirk@reisers.ca> Cc: Samuel Thibault <samuel.thibault@ens-lyon.org> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Max Staudt <max@enpas.org> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com> Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de> Cc: Jeremy Kerr <jk@codeconstruct.com.au> Cc: Matt Johnston <matt@codeconstruct.com.au> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20230810091510.13006-16-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-08-11tty: remove dummy tty_ldisc_ops::poll() implementationsJiri Slaby (SUSE)
tty_ldisc_ops::poll() is optional and needs not be provided. It is equal to returning 0. So remove all those from the code. Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20230810091510.13006-4-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-08-11Bluetooth: btrtl: Load FW v2 otherwise FW v1 for RTL8852CMax Chou
In this commit, prefer to load FW v2 if available. Fallback to FW v1 otherwise. This behavior is only for RTL8852C. Fixes: 9a24ce5e29b1 ("Bluetooth: btrtl: Firmware format v2 support") Cc: stable@vger.kernel.org Suggested-by: Juerg Haefliger <juerg.haefliger@canonical.com> Tested-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: btusb: Move btusb_recv_event_intel to btintelLuiz Augusto von Dentz
btusb_recv_event_intel is specific to Intel controllers therefore it shall be placed inside btintel.c so btusb don't have a mix of vendor specific code with the generic parts. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: btqca: Add WCN3988 supportLuca Weiss
Add support for the Bluetooth chip codenamed APACHE which is part of WCN3988. The firmware for this chip has a slightly different naming scheme compared to most others. For ROM Version 0x0200 we need to use apbtfw10.tlv + apnv10.bin and for ROM version 0x201 apbtfw11.tlv + apnv11.bin Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: btnxpuart: Add support for AW693 chipsetNeeraj Sanjay Kale
This adds support for NXP AW693 chipset in btnxpuart driver by adding FW name and bootloader signature. Based on the loader version bits 7:6 of the bootloader signature, the driver can choose between selecting secure and non-secure FW files. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: nokia: fix value check in nokia_bluetooth_serdev_probe()Yuanjun Gong
in nokia_bluetooth_serdev_probe(), check the return value of clk_prepare_enable() and return the error code if clk_prepare_enable() returns an unexpected value. Fixes: 7bb318680e86 ("Bluetooth: add nokia driver") Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11bluetooth: Explicitly include correct DT includesRob Herring
The DT of_device.h and of_platform.h date back to the separate of_platform_bus_type before it as merged into the regular platform bus. As part of that merge prepping Arm DT support 13 years ago, they "temporarily" include each other. They also include platform_device.h and of.h. As a result, there's a pretty much random mix of those include files used throughout the tree. In order to detangle these headers and replace the implicit includes with struct declarations, users need to explicitly include the correct includes. Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: btbcm: add default address for BCM43430A1Mans Rullgard
The BCM43430A1 has a default MAC address of AA:AA:AA:AA:AA:AA. Although, unlike some other entries, this does not include the chip name, it is clearly not a real address. This was found in AzureWave AW-NB197SM and AW-NM372SM modules. Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: btmtk: Fix kernel crash when processing coredumpChris Lu
There may be a potential kernel crash risk if 'skb->len - MTK_COREDUMP_END_LEN' value is less than 0 when doing memcmp in btmtk_process_coredump(). Check the value is valid before doing memcmp. [215.021695] Unable to handle kernel paging request at virtual address ffffff939fffd3c5 [215.021781] Mem abort info: [215.021805] ESR = 0x96000005 [215.021833] EC = 0x25: DABT (current EL), IL = 32 bits [215.021861] SET = 0, FnV = 0 [215.021875] EA = 0, S1PTW = 0 [215.021886] Data abort info: [215.021899] ISV = 0, ISS = 0x00000005 [215.021912] CM = 0, WnR = 0 [215.021929] swapper pgtable: 4k pages, 39-bit VAs, pgdp=00000000410de000 [215.021943] [ffffff939fffd3c5] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000 [215.021979] Internal error: Oops: 96000005 [#1] PREEMPT SMP [215.022496] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.10.186#3 (HASH:ad23 4) [215.022511] Hardware name: MediaTek Tomato board (DT) [215.022530] pstate: 80400009 (Nzcv daif +PAN -UAO -TCO BTYPE=--) [215.022556] pc : __pi_memcmp+0xd0/0x1b8 [215.022579] lr : btmtk_process_coredump+0xb0/0x5f8 [btmtk] [215.022593] sp : ffffffc010003d40 [215.022607] x29: ffffffc010003d40 x28: 0000000000000006 [215.022633] x27: ffffffda696350c0 x26: 0000000000000002 [215.022659] x25: 00000000000003ff x24: ffffff9360cca804 [215.022685] x23: 0000000000000000 x22: ffffff9365638500 [215.022710] x21: ffffff9365638700 x20: 0000000000000000 [215.022736] x19: ffffff936002e000 x18: 0000000000000000 [215.022761] x17: 0000000000000180 x16: ffffffda6881b8b4 [215.022787] x15: 0000000000000001 x14: 0000000000002d00 [215.022812] x13: 0000000000060000 x12: 0000000000000181 [215.022837] x11: 0000000000000006 x10: fffffffffffffffd [215.022862] x9 : 0000000000000006 x8 : 0000000000000003 [215.022887] x7 : 0000000000000000 x6 : 0000000000000000 [215.022913] x5 : ffffff93656387b8 x4 : 0000000000000000 [215.022938] x3 : ffffffc010003c18 x2 : 0000000000000006 [215.022963] x1 : ffffffda09d4124a x0 : ffffff939fffd3c5 [215.022989] Call trace: [215.023012] __pi_memcmp+0xd0/0x1b8 [215.023053] btusb_recv_acl_mtk+0x64/0x90 [btusb (HASH:dc6b 5)] [215.023087] btusb_recv_bulk+0x118/0x170 [btusb (HASH:dc6b 5)] [215.023121] btusb_bulk_complete+0x8c/0x148 [btusb (HASH:dc6b 5)] [215.023144] __usb_hcd_giveback_urb+0xbc/0x148 [215.023164] usb_giveback_urb_bh+0xb4/0x190 [215.023184] tasklet_action_common+0x98/0x1a0 [215.023201] tasklet_action+0x2c/0x38 [215.023220] __do_softirq+0xe0/0x38c [215.023241] invoke_softirq+0x34/0x6c [215.023258] irq_exit+0x6c/0xb0 [215.023279] __handle_domain_irq+0x98/0xd4 [215.023296] gic_handle_irq+0x5c/0x11c [215.023313] el1_irq+0xd0/0x180 [215.023332] cpuidle_enter_state+0xac/0x338 [215.023349] cpuidle_enter+0x40/0x70 [215.023366] do_idle+0x150/0x278 [215.023384] cpu_startup_entry+0x2c/0x58 [215.023401] rest_init+0xdc/0xec [215.023419] arch_call_rest_init+0x18/0x24 [215.023435] start_kernel+0x334/0x400 [215.023460] Code: 91002129 eb09010a 9a89810b cb0b0042 (38401403) [215.023478] ---[ end trace 28668fd20c7a90cd ] Fixes: 2822cd0173ad ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support") Signed-off-by: Chris Lu <chris.lu@mediatek.com> Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: btusb: Add support for another MediaTek 7922 VID/PIDRoger Gammans
This one is found on the Dell Inspiron 2-in-1 7435 The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0f1 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Roger Gammans <rgammans@gammascience.co.uk> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: hci_ldisc: check HCI_UART_PROTO_READY flag in HCIUARTGETPROTOLee, Chun-Yi
This patch adds code to check HCI_UART_PROTO_READY flag before accessing hci_uart->proto. It fixes the race condition in hci_uart_tty_ioctl() between HCIUARTSETPROTO and HCIUARTGETPROTO. This issue bug found by Yu Hao and Weiteng Chen: BUG: general protection fault in hci_uart_tty_ioctl [1] The information of C reproducer can also reference the link [2] Reported-by: Yu Hao <yhao016@ucr.edu> Closes: https://lore.kernel.org/all/CA+UBctC3p49aTgzbVgkSZ2+TQcqq4fPDO7yZitFT5uBPDeCO2g@mail.gmail.com/ [1] Reported-by: Weiteng Chen <wchen130@ucr.edu> Closes: https://lore.kernel.org/lkml/CA+UBctDPEvHdkHMwD340=n02rh+jNRJNNQ5LBZNA+Wm4Keh2ow@mail.gmail.com/T/ [2] Signed-off-by: "Lee, Chun-Yi" <jlee@suse.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: btusb: Add new VID/PID 04ca/3804 for MT7922Chris Lu
Add VID 04ca & PID 3804 for MediaTek MT7922 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=3804 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: btusb: Add new VID/PID 0489/e102 for MT7922Chris Lu
Add VID 0489 & PID e102 for MediaTek MT7922 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e102 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: Add support for Gale Peak (8087:0036)Kiran K
Devices from /sys/kernel/debug/usb/devices: T: Bus=09 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0036 Rev= 0.00 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: btusb: Add a new VID/PID 0489/e0f6 for MT7922Chris Lu
Add VID/PID 0489/e0f6 for MediaTek MT7922 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0f6 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2023-08-11Bluetooth: btusb: Add device 0489:e0f5 as MT7922 deviceValentin David
Asus ROG Ally gaming computer has a MediaTek MT7922 chip that uses USB id 0489:e0f5 and needs to be added to the table. Without this, the device is not usable and gives the following error: Bluetooth: hci0: Opcode 0x c03 failed: -110 Output from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0f5 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Valentin David <valentin.david@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
generated by cgit (git 2.34.1) at 2025-07-18 06:50:21 +0000