| Age | Commit message (Collapse) | Author |
|---|
|
The original comment that describes the function
nand_davinci_read_page_hwecc_oob_first() is very obscure and it is hard
to understand what it is for.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-3-paul@crapouillou.net
|
|
The function nand_davinci_read_page_hwecc_oob_first() first reads the
OOB data, extracts the ECC information, programs the ECC hardware before
reading the actual data in a loop.
Right after the OOB data was read, it called nand_read_page_op() to
reset the read cursor to the beginning of the page. This caused the
first page to be read twice: in that call, and later in the loop.
Address that issue by changing the call to nand_read_page_op() to
nand_change_read_column_op(), which will only reset the read cursor.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-2-paul@crapouillou.net
|
|
The function nand_davinci_read_page_hwecc_oob_first() does read the ECC
data from the OOB area. Therefore it does not need to calculate the ECC
as it is already available.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb82c ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-1-paul@crapouillou.net
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"Core:
- Remove obsolete macros only used by the old nand_ecclayout struct
- Don't remove debugfs directory if device is in use
- MAINTAINERS:
- Add entry for Qualcomm NAND controller driver
- Update the devicetree documentation path of hyperbus
MTD devices:
- block2mtd:
- Add support for an optional custom MTD label
- Minor refactor to avoid hard coded constant
- mtdswap: Remove redundant assignment of pointer eb
CFI:
- Fixup CFI on ixp4xx
Raw NAND controller drivers:
- Arasan:
- Prevent an unsupported configuration
- Xway, Socrates: plat_nand, Pasemi, Orion, mpc5121, GPIO, Au1550nd,
AMS-Delta:
- Keep the driver compatible with on-die ECC engines
- cs553x, lpc32xx_slc, ndfc, sharpsl, tmio, txx9ndfmc:
- Revert the commits: "Fix external use of SW Hamming ECC helper"
- And let callers use the bare Hamming helpers
- Fsmc: Fix use of SM ORDER
- Intel:
- Fix potential buffer overflow in probe
- xway, vf610, txx9ndfm, tegra, stm32, plat_nand, oxnas, omap, mtk,
hisi504, gpmi, gpio, denali, bcm6368, atmel:
- Make use of the helper function devm_platform_ioremap_resource{,byname}()
Onenand drivers:
- Samsung: Drop Exynos4 and describe driver in KConfig
Raw NAND chip drivers:
- Hynix: Add support for H27UCG8T2ETR-BC MLC NAND
SPI NOR core:
- Add spi-nor device tree binding under SPI NOR maintainers
SPI NOR manufacturer drivers:
- Enable locking for n25q128a13
SPI NOR controller drivers:
- Use devm_platform_ioremap_resource_byname()"
* tag 'mtd/for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (50 commits)
mtd: core: don't remove debugfs directory if device is in use
MAINTAINERS: Update the devicetree documentation path of hyperbus
mtd: block2mtd: add support for an optional custom MTD label
mtd: block2mtd: minor refactor to avoid hard coded constant
mtd: fixup CFI on ixp4xx
mtd: rawnand: arasan: Prevent an unsupported configuration
MAINTAINERS: Add entry for Qualcomm NAND controller driver
mtd: rawnand: hynix: Add support for H27UCG8T2ETR-BC MLC NAND
mtd: rawnand: xway: Keep the driver compatible with on-die ECC engines
mtd: rawnand: socrates: Keep the driver compatible with on-die ECC engines
mtd: rawnand: plat_nand: Keep the driver compatible with on-die ECC engines
mtd: rawnand: pasemi: Keep the driver compatible with on-die ECC engines
mtd: rawnand: orion: Keep the driver compatible with on-die ECC engines
mtd: rawnand: mpc5121: Keep the driver compatible with on-die ECC engines
mtd: rawnand: gpio: Keep the driver compatible with on-die ECC engines
mtd: rawnand: au1550nd: Keep the driver compatible with on-die ECC engines
mtd: rawnand: ams-delta: Keep the driver compatible with on-die ECC engines
Revert "mtd: rawnand: cs553x: Fix external use of SW Hamming ECC helper"
Revert "mtd: rawnand: lpc32xx_slc: Fix external use of SW Hamming ECC helper"
Revert "mtd: rawnand: ndfc: Fix external use of SW Hamming ECC helper"
...
|
|
Under the following conditions:
* after rounding up by 4 the number of bytes to transfer (this is
related to the controller's internal constraints),
* if this (rounded) amount of data is situated beyond the end of the
device,
* and only in NV-DDR mode,
the Arasan NAND controller timeouts.
This currently can happen in a particular helper used when picking
software ECC algorithms. Let's prevent this situation by refusing to use
the NV-DDR interface with software engines.
Fixes: 4edde6031458 ("mtd: rawnand: arasan: Support NV-DDR interface")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211008163640.1753821-1-miquel.raynal@bootlin.com
|
|
Add support for the H27UCG8T2ETR-BC MLC NAND. The NAND is used widely
in the NTC CHIP, is an MLC type NAND, and is 8GB in size. Neither
JEDEC nor ONFI detection identifies it correctly, so the ID is added
to the nand_ids.c file. Additionally, per the datasheet this NAND
appears to use the same paired pages scheme as the Toshiba
TC58TEG5DCLTA00 (dist3), so add support for that to enable use in
SLC emulation mode.
Tested on a NTC CHIP the device is able to write to a ubifs formatted
partition, and then have U-Boot (with proposed patches) boot from a
kernel located on that ubifs formatted partition.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210930162402.344-1-macroalpha82@gmail.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: d525914b5bd8 ("mtd: rawnand: xway: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Cc: Jan Hoffmann <jan@3e8.eu>
Cc: Kestrel seventyfour <kestrelseventyfour@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-10-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: b36bf0a0fe5d ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-9-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 612e048e6aab ("mtd: rawnand: plat_nand: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-8-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 8fc6f1f042b2 ("mtd: rawnand: pasemi: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-7-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 553508cec2e8 ("mtd: rawnand: orion: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-6-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 6dd09f775b72 ("mtd: rawnand: mpc5121: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-5-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: f6341f6448e0 ("mtd: rawnand: gpio: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-4-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: dbffc8ccdf3a ("mtd: rawnand: au1550: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-3-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 59d93473323a ("mtd: rawnand: ams-delta: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-2-miquel.raynal@bootlin.com
|
|
This reverts commit 56a8d3fd1f342d10ee7b27e9ac0f4d00b5fbb91c.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-9-miquel.raynal@bootlin.com
|
|
This reverts commit c4b7d7c480d607e4f52d310d9d16b194868d0917.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-8-miquel.raynal@bootlin.com
|
|
This reverts commit 3e09c0252501829b14b10f14e1982aaab77d0b80.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-7-miquel.raynal@bootlin.com
|
|
This reverts commit 46fcb57e6b7283533ebf8ba17a6bd30fa88bdc9f.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-6-miquel.raynal@bootlin.com
|
|
This reverts commit 6a4c5ada577467a5f79e06f2c5e69c09983c22fb.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-5-miquel.raynal@bootlin.com
|
|
This reverts commit 3d227a0b0ce319edbff6fd0d8af4d66689e477cc.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-4-miquel.raynal@bootlin.com
|
|
The introduction of the generic ECC engine API lead to a number of
changes in various drivers which broke some of them. Here is a typical
example: I expected the SM_ORDER option to be handled by the Hamming ECC
engine internals. Problem: the fsmc driver does not instantiate (yet) a
real ECC engine object so we had to use a 'bare' ECC helper instead of
the shiny rawnand functions. However, when not intializing this engine
properly and using the bare helpers, we do not get the SM ORDER feature
handled automatically. It looks like this was lost in the process so
let's ensure we use the right SM ORDER now.
Fixes: ad9ffdce4539 ("mtd: rawnand: fsmc: Fix external use of SW Hamming ECC helper")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-2-miquel.raynal@bootlin.com
|
|
From QPIC V2 onwards there is a separate register to read
last code word "QPIC_NAND_READ_LOCATION_LAST_CW_n".
qcom_nandc_read_cw_raw() is used to read only one code word
at a time. If we will configure number of code words to 1 in
in QPIC_NAND_DEV0_CFG0 register then QPIC controller thinks
its reading the last code word, since from QPIC V2 onwards
we are having separate register to read the last code word,
we have to configure "QPIC_NAND_READ_LOCATION_LAST_CW_n"
register to fetch data from controller buffer to system
memory.
Fixes: 503ee5aad430 ("mtd: rawnand: qcom: update last code word register")
Cc: stable@kernel.org
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1630998357-1359-1-git-send-email-mdalam@codeaurora.org
|
|
ebu_nand_probe() read the value of u32 variable "cs" from the device
firmware description and used it as the index for array ebu_host->cs
that can contain MAX_CS (2) elements at most. That could result in
a buffer overflow and various bad consequences later.
Fix the potential buffer overflow by restricting values of "cs" with
MAX_CS in probe.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0b1039f016e8 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Co-developed-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210903082653.16441-1-novikov@ispras.ru
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074252.9633-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074245.9583-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074237.9533-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074230.9483-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074222.9433-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074215.9383-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074207.9333-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074200.9283-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074153.9233-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074145.9183-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074138.9133-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource_byname()
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074130.9083-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074123.9033-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource_byname()
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074116.8983-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource_byname()
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074108.8933-1-caihuoqing@baidu.com
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074031.8883-1-caihuoqing@baidu.com
|
|
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769330c34b4deabeed939325c77a7ec2f.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
|
|
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-10-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD changes:
- blkdevs:
- Simplify the refcounting in blktrans_{open, release}
- Simplify blktrans_getgeo
- Remove blktrans_ref_mutex
- Simplify blktrans_dev_get
- Use lockdep_assert_held
- Don't hold del_mtd_blktrans_dev in blktrans_{open, release}
- ftl:
- Don't cast away the type when calling add_mtd_blktrans_dev
- Don't cast away the type when calling add_mtd_blktrans_dev
- Use container_of() rather than cast
- Fix use-after-free
- Add discard support
- Allow use of MTD_RAM for testing purposes
- concat:
- Check _read, _write callbacks existence before assignment
- Judge callback existence based on the master
- maps:
- Maps: remove dead MTD map driver for PMC-Sierra MSP boards
- mtdblock:
- Warn if added for a NAND device
- Add comment about UBI block devices
- Update old JFFS2 mention in Kconfig
- partitions:
- Redboot: convert to YAML
NAND core changes:
- Repair Miquel Raynal's email address in MAINTAINERS
- Fix a couple of spelling mistakes in Kconfig
- bbt: Skip bad blocks when searching for the BBT in NAND
- Remove never changed ret variable
Raw NAND changes:
- cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
- intel: Fix error handling in probe
- omap: Fix kernel doc warning on 'calcuate' typo
- gpmc: Fix the ECC bytes vs. OOB bytes equation
SPI-NAND core changes:
- Properly fill the OOB area.
- Fix comment
SPI-NAND drivers changes:
- macronix: Add Quad support for serial NAND flash"
* tag 'mtd/for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (30 commits)
mtd: rawnand: cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
mtd_blkdevs: simplify the refcounting in blktrans_{open, release}
mtd_blkdevs: simplify blktrans_getgeo
mtd_blkdevs: remove blktrans_ref_mutex
mtd_blkdevs: simplify blktrans_dev_get
mtd/rfd_ftl: don't cast away the type when calling add_mtd_blktrans_dev
mtd/ftl: don't cast away the type when calling add_mtd_blktrans_dev
mtd_blkdevs: use lockdep_assert_held
mtd_blkdevs: don't hold del_mtd_blktrans_dev in blktrans_{open, release}
mtd: rawnand: intel: Fix error handling in probe
mtd: mtdconcat: Check _read, _write callbacks existence before assignment
mtd: mtdconcat: Judge callback existence based on the master
mtd: maps: remove dead MTD map driver for PMC-Sierra MSP boards
mtd: rfd_ftl: use container_of() rather than cast
mtd: rfd_ftl: fix use-after-free
mtd: rfd_ftl: add discard support
mtd: rfd_ftl: allow use of MTD_RAM for testing purposes
mtdblock: Warn if added for a NAND device
mtd: spinand: macronix: Add Quad support for serial NAND flash
mtdblock: Add comment about UBI block devices
...
|
|
'cafe_nand_probe()'
A successful 'init_rs_non_canonical()' call should be balanced by a
corresponding 'free_rs()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: 8c61b7a7f4d4 ("[MTD] [NAND] Use rslib for CAFÉ ECC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/fd313d3fb787458bcc73189e349f481133a2cdc9.1629532640.git.christophe.jaillet@wanadoo.fr
|
|
ebu_nand_probe() did not invoke ebu_dma_cleanup() and
clk_disable_unprepare() on some error handling paths. The patch fixes
that.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0b1039f016e8 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Co-developed-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817092930.23040-1-novikov@ispras.ru
|
|
The ret variable used for returning value in the function
`meson_nfc_rw_cmd_prepare_and_execute` is never change after initialising.
Therefore, we can remove it safely and return 0 at the end of the function.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210803113300.24230-1-wangborong@cdjrlc.com
|
|
Fix a trivial typo which is reported after enabling W=1 level of warnings:
drivers/mtd/nand/raw/omap2.c:927: warning: expecting prototype
for omap_calcuate_ecc(). Prototype was for omap_calculate_ecc() instead
Signed-off-by: Vladimir Molokov <vladimir@molokov.se>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210801205909.7102-1-vladimir@molokov.se
|
|
Due to 14f97f0b8e2b, the rawnand platforms without "secure-regions"
property defined in DT fails to probe. The issue is,
of_get_nand_secure_regions() errors out if
of_property_count_elems_of_size() returns a negative error code.
If the "secure-regions" property is not present in DT, then also we'll
get -EINVAL from of_property_count_elems_of_size() but it should not
be treated as an error for platforms not declaring "secure-regions"
in DT.
So fix this behaviour by checking for the existence of that property in
DT and return 0 if it is not present.
Fixes: 14f97f0b8e2b ("mtd: rawnand: Add a check in of_get_nand_secure_regions()")
Reported-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Tested-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210727062813.32619-1-manivannan.sadhasivam@linaro.org
|
|
There are two spelling mistakes in the Kconfig text. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210704094705.37175-1-colin.king@canonical.com
|
|
The blocks containing the bad block table can become bad as well. So
make sure to skip any blocks that are marked bad when searching for the
bad block table.
Otherwise in very rare cases where two BBT blocks wear out it might
happen that an obsolete BBT is used instead of a newer available
version.
This only applies to drivers which make use of a bad block marker in flash.
Other drivers won't be able to identify bad BBT blocks and thus can't skip
these.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210625123821.207458-1-s.riedmueller@phytec.de
|
