| Age | Commit message (Collapse) | Author |
|---|
|
Implement hw_control ops to drive Switch LEDs based on hardware events.
Netdev trigger is the declared supported trigger for hw control
operation and supports the following mode:
- tx
- rx
When hw_control_set is called, LEDs are set to follow the requested
mode.
Each LEDs will blink at 4Hz by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell 88E6361 is an 8-port switch derived from the
88E6393X/88E9193X/88E6191X switches family. It can benefit from the
existing mv88e6xxx driver by simply adding the proper switch description in
the driver. Main differences with other switches from this
family are:
- 8 ports exposed (instead of 11): ports 1, 2 and 8 not available
- No 5GBase-x nor SFI/USXGMII support
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some switches families have minor differences on supported link speed for
ports. Instead of redefining a new port_max_speed_mode for each different
configuration, allow to pass mv88e6xxx_chip structure to allow
differentiating those chips by known chip id
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
88E6393X/88E6193X/88E6191X switches have in fact 8 internal PHYs, but those
are not present starting at port 0: supported ports go from 1 to 8
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mv88e6xxx currently assumes that switch equipped with internal phys have
those phys mapped contiguously starting from port 0 (see
mv88e6xxx_phy_is_internal). However, some switches have internal PHYs but
NOT starting from port 0. For example 88e6393X, 88E6193X and 88E6191X have
integrated PHYs available on ports 1 to 8
To properly support this offset, add a new field to allow specifying an
internal PHYs layout. If field is not set, default layout is assumed (start
at port 0)
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make sure to use existing helper to get internal PHYs count instead of
redoing it manually
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since this function is a simple helper, we do not need to pass a full
dsa_switch structure, we can directly pass the mv88e6xxx_chip structure.
Doing so will allow to share this function with any other function
not manipulating dsa_switch structure but needing info about number of
internal phys
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is no gpiod_export() and gpiod_unexport() looks pretty much stray.
The gpiod_export() and gpiod_unexport() shouldn't be used in the code,
GPIO sysfs is deprecated. That said, simply drop the stray call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230528142531.38602-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This update introduces specific register access boundaries for the
KSZ8873 and KSZ8863 chips within the DSA Microchip driver. The outlined
ranges target global control registers, port registers, and advanced
control registers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
validation
This patch prepares the ksz8863_smi part of ksz8 driver to utilize the
regmap register access validation feature.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The only place where this variable would be set to false is the
ksz8_config_cpu_port() function. But it is done in a bogus way:
for (i = 0; i < dev->phy_port_cnt; i++) {
if (i == dev->phy_port_cnt) <--- will be never executed.
break;
p->on = 1;
So, we never have a situation where p->on = 0. In this case, we can just
remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It is not immediately obvious that this driver allocates, via the
KSZ_REGMAP_TABLE() macro, 3 regmaps for register access: dev->regmap[0]
for 8-bit access, dev->regmap[1] for 16-bit and dev->regmap[2] for
32-bit access.
In future changes that add support for reg_fields, each field will have
to specify through which of the 3 regmaps it's going to go. Add an enum
now, to denote one of the 3 register access widths, and make the code go
through some wrapper functions for easier review and further
modification.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch refines the error handling mechanism for 8-bit register
read-modify-write operations. In case of a failure, it now logs an error
message detailing the problematic offset. This enhancement aids in
debugging by providing more precise information when these operations
encounter issues.
Furthermore, the ksz_prmw8() function has been updated to return error
values rather than void, enabling calling functions to appropriately
respond to errors.
Additionally, in case of an error that affects both the current and
future accesses, the PHY driver will log the errors consistently, akin
to the existing behavior in all ksz_read*/ksz_write* helpers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use the newly introduced lynx_pcs_create_mdiodev() which simplifies the
creation and destruction of the lynx PCS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the link forcing out of mac_config() and into the mac_prepare()
and mac_finish() methods. This results in no change to the order in
which these operations are performed, but does mean when we convert
mv88e6xxx to phylink_pcs support, we will continue to preserve this
ordering.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to datasheet, the command opcode must be specified
into bits [14:12] of the Extended Port Control register (EPC).
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marco Migliore <m.migliore@tiesse.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ports are in standalone mode, they should have learning disabled to
avoid adding new entries in the MAC lookup table which might be used by
other bridge ports to forward packets. While adding that, also make sure
learning is enabled for CPU port.
Fixes: 888cdb892b61 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.
Fixes: 888cdb892b61 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.
Fixes: 888cdb892b61 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On mt753x_cpu_port_enable() there's code that enables flooding for the CPU
port only. Since mt753x_cpu_port_enable() runs twice when both CPU ports
are enabled, port 6 becomes the only port to forward the frames to. But
port 5 is the active port, so no frames received from the user ports will
be forwarded to port 5 which breaks network connectivity.
Every bit of the BC_FFP, UNM_FFP, and UNU_FFP bits represents a port. Fix
this issue by setting the bit that corresponds to the CPU port without
overwriting the other bits.
Clear the bits beforehand only for the MT7531 switch. According to the
documents MT7621 Giga Switch Programming Guide v0.3 and MT7531 Reference
Manual for Development Board v1.0, after reset, the BC_FFP, UNM_FFP, and
UNU_FFP bits are set to 1 for MT7531, 0 for MT7530.
The commit 5e5502e012b8 ("net: dsa: mt7530: fix roaming from DSA user
ports") silently changed the method to set the bits on the MT7530_MFC.
Instead of clearing the relevant bits before mt7530_cpu_port_enable()
which runs under a for loop, the commit started doing it on
mt7530_cpu_port_enable().
Back then, this didn't really matter as only a single CPU port could be
used since the CPU port number was hardcoded. The driver was later changed
with commit 1f9a6abecf53 ("net: dsa: mt7530: get cpu-port via dp->cpu_dp
instead of constant") to retrieve the CPU port via dp->cpu_dp. With that,
this silent change became an issue for when using multiple CPU ports.
Fixes: 5e5502e012b8 ("net: dsa: mt7530: fix roaming from DSA user ports")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The multi-chip module MT7530 switch with a 40 MHz oscillator on the
MT7621AT, MT7621DAT, and MT7621ST SoCs forwards corrupt frames using
trgmii.
This is caused by the assumption that MT7621 SoCs have got 150 MHz PLL,
hence using the ncpo1 value, 0x0780.
My testing shows this value works on Unielec U7621-06, Bartel's testing
shows it won't work on Hi-Link HLK-MT7621A and Netgear WAC104. All devices
tested have got 40 MHz oscillators.
Using the value for 125 MHz PLL, 0x0640, works on all boards at hand. The
definitions for 125 MHz PLL exist on the Banana Pi BPI-R2 BSP source code
whilst 150 MHz PLL don't.
Forwarding frames using trgmii on the MCM MT7530 switch with a 25 MHz
oscillator on the said MT7621 SoCs works fine because the ncpo1 value
defined for it is for 125 MHz PLL.
Change the 150 MHz PLL comment to 125 MHz PLL, and use the 125 MHz PLL
ncpo1 values for both oscillator frequencies.
Link: https://github.com/BPI-SINOVOIP/BPI-R2-bsp/blob/81d24bbce7d99524d0771a8bdb2d6663e4eb4faa/u-boot-mt/drivers/net/rt2880_eth.c#L2195
Fixes: 7ef6f6f8d237 ("net: dsa: mt7530: Add MT7621 TRGMII mode support")
Tested-by: Bartel Eerdekens <bartel.eerdekens@constell8.be>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add rsvd2cpu capability for mv88e6321 model, to allow proper bpdu
processing.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Fixes: 51c901a775621 ("net: dsa: mv88e6xxx: distinguish Global 2 Rsvd2CPU")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With LEDS_CLASS=m, a built-in qca8k driver fails to link:
arm-linux-gnueabi-ld: drivers/net/dsa/qca/qca8k-leds.o: in function `qca8k_setup_led_ctrl':
qca8k-leds.c:(.text+0x1ea): undefined reference to `devm_led_classdev_register_ext'
Change the dependency to avoid the broken configuration.
Fixes: 1e264f9d2918 ("net: dsa: qca8k: add LEDs basic support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230420213639.2243388-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adjacent changes:
net/mptcp/protocol.h
63740448a32e ("mptcp: fix accept vs worker race")
2a6a870e44dd ("mptcp: stops worker on unaccepted sockets at listener close")
ddb1a072f858 ("mptcp: move first subflow allocation at mpc access time")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are two variants of the MT7531 switch IC which got different
features (and pins) regarding port 5:
* MT7531AE: SGMII/1000Base-X/2500Base-X SerDes PCS
* MT7531BE: RGMII
Moving the creation of the SerDes PCS from mt753x_setup to mt7530_probe
with commit 6de285229773 ("net: dsa: mt7530: move SGMII PCS creation
to mt7530_probe function") works fine for MT7531AE which got two
instances of mtk-pcs-lynxi, however, MT7531BE requires mt7531_pll_setup
to setup clocks before the single PCS on port 6 (usually used as CPU
port) starts to work and hence the PCS creation failed on MT7531BE.
Fix this by introducing a pointer to mt7531_create_sgmii function in
struct mt7530_priv and call it again at the end of mt753x_setup like it
was before commit 6de285229773 ("net: dsa: mt7530: move SGMII PCS
creation to mt7530_probe function").
Fixes: 6de285229773 ("net: dsa: mt7530: move SGMII PCS creation to mt7530_probe function")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/ZDvlLhhqheobUvOK@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Because of the logic in place, SW_HUGE_PACKET can never be set.
(If the first condition is true, then the 2nd one is also true, but is not
executed)
Change the logic and update each bit individually.
Fixes: 29d1e85f45e0 ("net: dsa: microchip: ksz8: add MTU configuration support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/43107d9e8b5b8b05f0cbd4e1f47a2bb88c8747b2.1681755535.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add LEDs blink_set() support to qca8k Switch Family.
These LEDs support hw accellerated blinking at a fixed rate
of 4Hz.
Reject any other value since not supported by the LEDs switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add LEDs basic support for qca8k Switch Family by adding basic
brightness_set() support.
Since these LEDs refelect port status, the default label is set to
":port". DT binding should describe the color and function of the
LEDs using standard LEDs api.
Each LED always have the device name as prefix. The device name is
composed from the mii bus id and the PHY addr resulting in example
names like:
- qca8k-0.0:00:amber:lan
- qca8k-0.0:00:white:lan
- qca8k-0.0:01:amber:lan
- qca8k-0.0:01:white:lan
These LEDs supports only blocking variant of the brightness_set()
function since they can sleep during access of the switch leds to set
the brightness.
While at it add to the qca8k header file each mode defined by the Switch
Documentation for future use.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move qca8k_port_to_phy() to qca8k header as it's useful for future
reference in Switch LEDs module since the same logic is applied to get
the right index of the switch port.
Make it inline as it's simple function that just decrease the port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to not transmit (preemptible) frames which will be received by
the link partner as corrupted (because it doesn't support FP), the
hardware requires the driver to program the QSYS_PREEMPTION_CFG_P_QUEUES
register only after the MAC Merge layer becomes active (verification
succeeds, or was disabled).
There are some cases when FP is known (through experimentation) to be
broken. Give priority to FP over cut-through switching, and disable FP
for known broken link modes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mqprio queue configuration can appear either through
TC_SETUP_QDISC_MQPRIO or through TC_SETUP_QDISC_TAPRIO. Make sure both
are treated in the same way.
Code does nothing new for now (except for rejecting multiple TXQs per
TC, which is a useless concept with DSA switches).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This doesn't apply anything to hardware and in general doesn't do
anything that the software variant doesn't do, except for checking that
there isn't more than 1 TXQ per TC (TXQs for a DSA switch are a dubious
concept anyway). The reason we add this is to be able to parse one more
field added to struct tc_mqprio_qopt_offload, namely preemptible_tcs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the switch emits an IRQ, we don't know what caused it, and we
iterate through all ports to check the MAC Merge status.
Move that iteration inside the ocelot lib; we will change the locking in
a future change and it would be good to encapsulate that lock completely
within the ocelot lib.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
That comment was written prior to knowing that what I was actually
seeing was a manifestation of the bug fixed in commit b4024c9e5c57
("felix: Fix initialization of ioremap resources").
There isn't any particular reason now why the hardware initialization is
done in felix_setup(), so just delete that comment to avoid spreading
misinformation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch can either take the MAC or the PHY role in an MII or RMII
link. There are distinct PHY_INTERFACE_ macros for these two roles.
Correct the mapping so that the `REV` version is used for the PHY
role.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230411023541.2372609-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts:
drivers/net/ethernet/google/gve/gve.h
3ce934558097 ("gve: Secure enough bytes in the first TX desc for all TCP pkts")
75eaae158b1b ("gve: Add XDP DROP and TX support for GQI-QPL format")
https://lore.kernel.org/all/20230406104927.45d176f5@canb.auug.org.au/
https://lore.kernel.org/all/c5872985-1a95-0bc8-9dcc-b6f23b439e9d@tessares.net/
Adjacent changes:
net/can/isotp.c
051737439eae ("can: isotp: fix race between isotp_sendsmg() and isotp_release()")
96d1c81e6a04 ("can: isotp: add module parameter for maximum pdu size")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To handle potential read/write operation failures, update
ksz8_w_sta_mac_table() to make use of the return values provided by
read/write functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since ksz8_w_sta_mac_table() is only used within ksz8795.c, make it static
to limit its scope.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
read/write functions
Take advantage of the return values provided by read/write functions in
ksz8_r_sta_mac_table() to handle cases where read/write operations may
fail.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
empty entries
Prepare for the next patch by ensuring that ksz8_r_sta_mac_table() does
not use error codes for empty entries. This change will enable better
handling of read/write errors in the upcoming patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As ksz8_r_sta_mac_table() is only used within ksz8795.c, there is no need
to export it. Make the function static for better encapsulation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
operations
Add support for add/del_fdb operations and utilize the refactored static
MAC table code. This resolves kernel warnings caused by the lack of fdb
add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move static MAC table operations to separate functions in order to reuse
the code for add/del_fdb. This is needed to address kernel warnings
caused by the lack of fdb add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add driver for the built-in Gigabit Ethernet switch which can be found
in the MediaTek MT7988 SoC.
The switch shares most of its design with MT7530 and MT7531, but has
it's registers mapped into the SoCs register space rather than being
connected externally or internally via MDIO.
Introduce a new platform driver to support that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As MT7530 and MT7531 internally use 32-bit wide registers, each access
to any register of the switch requires several operations on the MDIO
bus. Hence if there is congruent access, e.g. due to PCS or PHY
polling, this can mess up and interfere with another ongoing register
access sequence.
However, the MDIO bus mutex is only relevant for MDIO-connected
switches. Prepare switches which have there registers directly mapped
into the SoCs register space via MMIO which do not require such
locking. There we can simply use regmap's default locking mechanism.
Hence guard mutex operations to only be performed in case of MDIO
connected switches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split MT7530 switch driver into a common part and a part specific
for MDIO connected switches and multi-chip modules.
Move MDIO-specific functions to newly introduced mt7530-mdio.c while
keeping the common parts in mt7530.c.
Introduce new Kconfig symbol CONFIG_NET_DSA_MT7530_MDIO which is
implied by CONFIG_NET_DSA_MT7530.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MT7988 shares a significant part of the setup function with MT7531.
Split-off those parts into a shared function which is going to be used
also by mt7988_setup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move commonly used parts from mt7530_remove into new
mt7530_remove_common helper function which will be used by both,
mt7530_remove and the to-be-introduced mt7988_remove.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move commonly used parts from mt7530_probe into new mt7530_probe_common
helper function which will be used by both, mt7530_probe and the
to-be-introduced mt7988_probe.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation of splitting mt7530.c into a driver for MDIO-connected
as well as MDIO-accessed built-in switches on one hand and MMIO-accessed
built-in switches move the p5_inft_modes() function from mt7530.h to
mt7530.c. The function is only needed there and will trigger a compiler
warning about a defined but unused function otherwise when including
mt7530.h in the to-be-introduced bus-specific drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
