| Age | Commit message (Collapse) | Author |
|---|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
net/core/page_pool_user.c
0b11b1c5c320 ("netdev: let netlink core handle -EMSGSIZE errors")
429679dcf7d9 ("page_pool: fix netlink dump stop/resume")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Following the addition of new GTP RSS hash options to ethtool.h, this patch
implements the corresponding RSS settings for GTP packets in the Intel ice
driver. It enables users to configure RSS for GTP-U and GTP-C traffic over IPv4
and IPv6, utilizing the newly defined hash options.
The implementation covers the handling of gtpu(4|6), gtpc(4|6), gtpc(4|6)t,
gtpu(4|6)e, gtpu(4|6)u, and gtpu(4|6)d traffic, providing enhanced load
distribution for GTP traffic across multiple processing units.
Signed-off-by: Takeru Hayasaka <hayatake396@gmail.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Simplify stats accumulation logic to fix the case where we don't take
previous stat value into account, we should always respect it.
Main netdev stats of our PF (Tx/Rx packets/bytes) were reported orders of
magnitude too big during OpenStack reconfiguration events, possibly other
reconfiguration cases too.
The regression was reported to be between 6.1 and 6.2, so I was almost
certain that on of the two "preserve stats over reset" commits were the
culprit. While reading the code, it was found that in some cases we will
increase the stats by arbitrarily large number (thanks to ignoring "-prev"
part of condition, after zeroing it).
Note that this fixes also the case where we were around limits of u64, but
that was not the regression reported.
Full disclosure: I remember suggesting this particular piece of code to
Ben a few years ago, so blame on me.
Fixes: 2fd5e433cd26 ("ice: Accumulate HW and Netdev statistics over reset")
Reported-by: Nebojsa Stevanovic <nebojsa.stevanovic@gcore.com>
Link: https://lore.kernel.org/intel-wired-lan/VI1PR02MB439744DEDAA7B59B9A2833FE912EA@VI1PR02MB4397.eurprd02.prod.outlook.com
Reported-by: Christian Rohmann <christian.rohmann@inovex.de>
Link: https://lore.kernel.org/intel-wired-lan/f38a6ca4-af05-48b1-a3e6-17ef2054e525@inovex.de
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-03-05 (idpf, ice, i40e, igc, e1000e)
This series contains updates to idpf, ice, i40e, igc and e1000e drivers.
Emil disables local BH on NAPI schedule for proper handling of softirqs
on idpf.
Jake stops reporting of virtchannel RSS option which in unsupported on
ice.
Rand Deeb adds null check to prevent possible null pointer dereference
on ice.
Michal Schmidt moves DPLL mutex initialization to resolve uninitialized
mutex usage for ice.
Jesse fixes incorrect variable usage for calculating Tx stats on ice.
Ivan Vecera corrects logic for firmware equals check on i40e.
Florian Kauer prevents memory corruption for XDP_REDIRECT on igc.
Sasha reverts an incorrect use of FIELD_GET which caused a regression
for Wake on LAN on e1000e.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Older versions of GCC really want to know the full definition
of the type involved in rcu_assign_pointer().
struct dpll_pin is defined in a local header, net/core can't
reach it. Move all the netdev <> dpll code into dpll, where
the type is known. Otherwise we'd need multiple function calls
to jump between the compilation units.
This is the same problem the commit under fixes was trying to address,
but with rcu_assign_pointer() not rcu_dereference().
Some of the exports are not needed, networking core can't
be a module, we only need exports for the helpers used by
drivers.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/all/35a869c8-52e8-177-1d4d-e57578b99b6@linux-m68k.org/
Fixes: 640f41ed33b5 ("dpll: fix build failure due to rcu_dereference_check() on unknown type")
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240305013532.694866-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix an obviously incorrect assignment, created with a typo or cut-n-paste
error.
Fixes: 5995ef88e3a8 ("ice: realloc VSI stats arrays")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The pf->dplls.lock mutex is initialized too late, after its first use.
Move it to the top of ice_dpll_init.
Note that the "err_exit" error path destroys the mutex. And the mutex is
the last thing destroyed in ice_dpll_deinit.
This fixes the following warning with CONFIG_DEBUG_MUTEXES:
ice 0000:10:00.0: The DDP package was successfully loaded: ICE OS Default Package version 1.3.36.0
ice 0000:10:00.0: 252.048 Gb/s available PCIe bandwidth (16.0 GT/s PCIe x16 link)
ice 0000:10:00.0: PTP init successful
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 0 PID: 410 at kernel/locking/mutex.c:587 __mutex_lock+0x773/0xd40
Modules linked in: crct10dif_pclmul crc32_pclmul crc32c_intel polyval_clmulni polyval_generic ice(+) nvme nvme_c>
CPU: 0 PID: 410 Comm: kworker/0:4 Not tainted 6.8.0-rc5+ #3
Hardware name: HPE ProLiant DL110 Gen10 Plus/ProLiant DL110 Gen10 Plus, BIOS U56 10/19/2023
Workqueue: events work_for_cpu_fn
RIP: 0010:__mutex_lock+0x773/0xd40
Code: c0 0f 84 1d f9 ff ff 44 8b 35 0d 9c 69 01 45 85 f6 0f 85 0d f9 ff ff 48 c7 c6 12 a2 a9 85 48 c7 c7 12 f1 a>
RSP: 0018:ff7eb1a3417a7ae0 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
RDX: 0000000000000002 RSI: ffffffff85ac2bff RDI: 00000000ffffffff
RBP: ff7eb1a3417a7b80 R08: 0000000000000000 R09: 00000000ffffbfff
R10: ff7eb1a3417a7978 R11: ff32b80f7fd2e568 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: ff32b7f02c50e0d8
FS: 0000000000000000(0000) GS:ff32b80efe800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055b5852cc000 CR3: 000000003c43a004 CR4: 0000000000771ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
? __warn+0x84/0x170
? __mutex_lock+0x773/0xd40
? report_bug+0x1c7/0x1d0
? prb_read_valid+0x1b/0x30
? handle_bug+0x42/0x70
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? __mutex_lock+0x773/0xd40
? rcu_is_watching+0x11/0x50
? __kmalloc_node_track_caller+0x346/0x490
? ice_dpll_lock_status_get+0x28/0x50 [ice]
? __pfx_ice_dpll_lock_status_get+0x10/0x10 [ice]
? ice_dpll_lock_status_get+0x28/0x50 [ice]
ice_dpll_lock_status_get+0x28/0x50 [ice]
dpll_device_get_one+0x14f/0x2e0
dpll_device_event_send+0x7d/0x150
dpll_device_register+0x124/0x180
ice_dpll_init_dpll+0x7b/0xd0 [ice]
ice_dpll_init+0x224/0xa40 [ice]
? _dev_info+0x70/0x90
ice_load+0x468/0x690 [ice]
ice_probe+0x75b/0xa10 [ice]
? _raw_spin_unlock_irqrestore+0x4f/0x80
? process_one_work+0x1a3/0x500
local_pci_probe+0x47/0xa0
work_for_cpu_fn+0x17/0x30
process_one_work+0x20d/0x500
worker_thread+0x1df/0x3e0
? __pfx_worker_thread+0x10/0x10
kthread+0x103/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
irq event stamp: 125197
hardirqs last enabled at (125197): [<ffffffff8416409d>] finish_task_switch.isra.0+0x12d/0x3d0
hardirqs last disabled at (125196): [<ffffffff85134044>] __schedule+0xea4/0x19f0
softirqs last enabled at (105334): [<ffffffff84e1e65a>] napi_get_frags_check+0x1a/0x60
softirqs last disabled at (105332): [<ffffffff84e1e65a>] napi_get_frags_check+0x1a/0x60
---[ end trace 0000000000000000 ]---
Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The function ice_bridge_setlink() may encounter a NULL pointer dereference
if nlmsg_find_attr() returns NULL and br_spec is dereferenced subsequently
in nla_for_each_nested(). To address this issue, add a check to ensure that
br_spec is not NULL before proceeding with the nested attribute iteration.
Fixes: b1edc14a3fbf ("ice: Implement ice_bridge_getlink and ice_bridge_setlink")
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The E800 series hardware uses the same iAVF driver as older devices,
including the virtchnl negotiation scheme.
This negotiation scheme includes a mechanism to determine what type of RSS
should be supported, including RSS over PF virtchnl messages, RSS over
firmware AdminQ messages, and RSS via direct register access.
The PF driver will always prefer VIRTCHNL_VF_OFFLOAD_RSS_PF if its
supported by the VF driver. However, if an older VF driver is loaded, it
may request only VIRTCHNL_VF_OFFLOAD_RSS_REG or VIRTCHNL_VF_OFFLOAD_RSS_AQ.
The ice driver happily agrees to support these methods. Unfortunately, the
underlying hardware does not support these mechanisms. The E800 series VFs
don't have the appropriate registers for RSS_REG. The mailbox queue used by
VFs for VF to PF communication blocks messages which do not have the
VF-to-PF opcode.
Stop lying to the VF that it could support RSS over AdminQ or registers, as
these interfaces do not work when the hardware is operating on an E800
series device.
In practice this is unlikely to be hit by any normal user. The iAVF driver
has supported RSS over PF virtchnl commands since 2016, and always defaults
to using RSS_PF if possible.
In principle, nothing actually stops the existing VF from attempting to
access the registers or send an AQ command. However a properly coded VF
will check the capability flags and will report a more useful error if it
detects a case where the driver does not support the RSS offloads that it
does.
Fixes: 1071a8358a28 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
1. pcaps are free'd right after AQ routines are done, no need for
devm_'s
2. a test frame for loopback test in ethtool -t is destroyed at the end
of the test so we don't need devm_ here either.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_down() clears QINT_TQCTL_CAUSE_ENA_M bit twice, which is not
necessary. First clearing happens in ice_vsi_dis_irq() and second in
ice_vsi_stop_tx_ring() - remove the first one.
While at it, make ice_vsi_dis_irq() static as ice_down() is the only
current caller of it.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The indentation for ice_set_ctx and ice_write_rxq_ctx breaks the function
name after the return type. This style of breaking is used a lot throughout
the ice driver, even in cases where its not actually helpful for
readability. We no longer prefer this style of line splitting in the
driver, and new code is avoiding it.
Normally, I would leave this alone unless the actual function contents or
description needed updating. However, a future change is going to add
inverse functions for converting packed context to unpacked context
structures. To keep this code uniform with the existing set functions, fix
up the style to the modern format of keeping the type on the same line.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The functions used to pack the Tx and Rx context into the hardware format
rely on using BIT() and then subtracting 1 to get a bitmask. These
functions even have a comment about how x86 machines can't use this method
for certain widths because the SHL instructions will not work properly.
The Linux kernel already provides the GENMASK macro for generating a
suitable bitmask. Further, GENMASK is capable of generating the mask
including the shift_width. Since width is the total field width, take care
to subtract one to get the final bit position.
Since we now include the shifted bits as part of the mask, shift the source
value first before applying the mask.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In ice_common.c there are 4 functions used for converting the unpacked
software Tx and Rx context structure data into the packed format used by
hardware. These functions have extremely generic names:
* ice_write_byte
* ice_write_word
* ice_write_dword
* ice_write_qword
When I saw these function names my first thought was "write what? to
where?". Understanding what these functions do requires looking at the
implementation details. The functions take bits from an unpacked structure
and copy them into the packed layout used by hardware.
As part of live migration, we will want functions which perform the inverse
operation of reading bits from the packed layout and copying them into the
unpacked format. Naming these as "ice_read_byte", etc would be very
confusing since they appear to write data.
In preparation for adding this new inverse operation, rename the existing
functions to use the prefix "ice_pack_ctx_". This makes it clear that they
perform the bit packing while copying from the unpacked software context
structure to the packed hardware context.
The inverse operations can then neatly be named ice_unpack_ctx_*, clearly
indicating they perform the bit unpacking while copying from the packed
hardware context to the unpacked software context structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The lan_vsi_num field of the VF structure is no longer used for any
purpose. Remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When initializing over virtchnl, the PF is required to pass a VSI ID to the
VF as part of its capabilities exchange. The VF driver reports this value
back to the PF in a variety of commands. The PF driver validates that this
value matches the value it sent to the VF.
Some hardware families such as the E700 series could use this value when
reading RSS registers or communicating directly with firmware over the
Admin Queue.
However, E800 series hardware does not support any of these interfaces and
the VF's only use for this value is to report it back to the PF. Thus,
there is no requirement that this value be an actual VSI ID value of any
kind.
The PF driver already does not trust that the VF sends it a real VSI ID.
The VSI structure is always looked up from the VF structure. The PF does
validate that the VSI ID provided matches a VSI associated with the VF, but
otherwise does not use the VSI ID for any purpose.
Instead of reporting the VSI number relative to the PF space, report a
fixed value of 1. When communicating with the VF over virtchnl, validate
that the VSI number is returned appropriately.
This avoids leaking information about the firmware of the PF state.
Currently the ice driver only supplies a VF with a single VSI. However, it
appears that virtchnl has some support for allowing multiple VSIs. I did
not attempt to implement this. However, space is left open to allow further
relative indexes if additional VSIs are provided in future feature
development. For this reason, keep the ice_vc_isvalid_vsi_id function in
place to allow extending it for multiple VSIs in the future.
This change will also simplify handling of live migration in a future
series. Since we no longer will provide a real VSI number to the VF, there
will be no need to keep track of this number when migrating to a new host.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_vc_fdir_param_check() function validates that the VSI ID of the
virtchnl flow director command matches the VSI number of the VF. This is
already checked by the call to ice_vc_isvalid_vsi_id() immediately
following this.
This check is unnecessary since ice_vc_isvalid_vsi_id() already confirms
this by checking that the VSI ID can locate the VSI associated with the VF
structure.
Furthermore, a following change is going to refactor the ice driver to
report VSI IDs using a relative index for each VF instead of reporting the
PF VSI number. This additional check would break that logic since it
enforces that the VSI ID matches the VSI number.
Since this check duplicates the logic in ice_vc_isvalid_vsi_id() and gets
in the way of refactoring that logic, remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_vc_isvalid_q_id() function takes a VSI index and a queue ID. It
looks up the VSI from its index, and then validates that the queue number
is valid for that VSI.
The VSI ID passed is typically a VSI index from the VF. This VSI number is
validated by the PF to ensure that it matches the VSI associated with the
VF already.
In every flow where ice_vc_isvalid_q_id() is called, the PF driver already
has a pointer to the VSI associated with the VF. This pointer is obtained
using ice_get_vf_vsi(), rather than looking up the VSI using the index sent
by the VF.
Since we already know which VSI to operate on, we can modify
ice_vc_isvalid_q_id() to take a VSI pointer instead of a VSI index. Pass
the VSI we found from ice_get_vf_vsi() instead of re-doing the lookup. This
removes some unnecessary computation and scanning of the VSI list.
It also removes the last place where the driver directly used the VSI
number from the VF. This will pave the way for refactoring to communicate
relative VSI numbers to the VF instead of absolute numbers from the PF
space.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
During VSI reconfiguration filters and VSI config which is set in
ice_vf_init_host_cfg() are lost. Recall the host configuration function
to restore them.
Without this config VF on which MSI-X amount was changed might had a
connection problems.
Fixes: 4d38cb44bd32 ("ice: manage VFs MSI-X using resource tracking")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_qp_dis() currently does things in very mixed way. Tx is stopped
before disabling IRQ on related queue vector, then it takes care of
disabling Rx and finally NAPI is disabled.
Let us start with disabling IRQs in the first place followed by turning
off NAPI. Then it is safe to handle queues.
One subtle change on top of that is that even though ice_qp_ena() looks
more sane, clear ICE_CFG_BUSY as the last thing there.
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/mptcp/protocol.c
adf1bb78dab5 ("mptcp: fix snd_wnd initialization for passive socket")
9426ce476a70 ("mptcp: annotate lockless access for RX path fields")
https://lore.kernel.org/all/20240228103048.19255709@canb.auug.org.au/
Adjacent changes:
drivers/dpll/dpll_core.c
0d60d8df6f49 ("dpll: rely on rcu for netdev_dpll_pin()")
e7f8df0e81bf ("dpll: move xa_erase() call in to match dpll_pin_alloc() error path order")
drivers/net/veth.c
1ce7d306ea63 ("veth: try harder when allocating queue memory")
0bef512012b1 ("net: add netdev_lockdep_set_classes() to virtual drivers")
drivers/net/wireless/intel/iwlwifi/mvm/d3.c
8c9bef26e98b ("wifi: iwlwifi: mvm: d3: implement suspend with MLO")
78f65fbf421a ("wifi: iwlwifi: mvm: ensure offloading TID queue exists")
net/wireless/nl80211.c
f78c1375339a ("wifi: nl80211: reject iftype change with mesh ID change")
414532d8aa89 ("wifi: cfg80211: use IEEE80211_MAX_MESH_ID_LEN appropriately")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 91fdbce7e8d6 ("ice: Add support in the driver for associating
queue with napi") invoked the netif_queue_set_napi() call. This
kernel function requires to be called with rtnl_lock taken,
otherwise ASSERT_RTNL() warning will be triggered. ice_vsi_rebuild()
initiating this call is under rtnl_lock when the rebuild is in
response to configuration changes from external interfaces (such as
tc, ethtool etc. which holds the lock). But, the VSI rebuild
generated from service tasks and resets (PFR/CORER/GLOBR) is not
under rtnl lock protection. Handle these cases as well to hold lock
before the kernel call (by setting the 'locked' boolean to false).
netif_queue_set_napi() is also used to clear previously set napi
in the q_vector unroll flow. Handle this for locked/lockless execution
paths.
Fixes: 91fdbce7e8d6 ("ice: Add support in the driver for associating queue with napi")
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Do not allow to set phase adjust value for a pin if PF reset is in
progress, this would cause confusing netlink extack errors as the firmware
cannot process the request properly during the reset time.
Return (-EBUSY) and report extack error for the user who tries configure
pin phase adjust during the reset time.
Test by looping execution of below steps until netlink error appears:
- perform PF reset
$ echo 1 > /sys/class/net/<ice PF>/device/reset
- change pin phase adjust value:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--do pin-set --json '{"id":0, "phase-adjust":1000}'
Fixes: 90e1c90750d7 ("ice: dpll: implement phase related callbacks")
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Do not allow dpll periodic work function to acquire data from firmware
if PF reset is in progress. Acquiring data will cause dmesg errors as the
firmware cannot respond or process the request properly during the reset
time.
Test by looping execution of below step until dmesg error appears:
- perform PF reset
$ echo 1 > /sys/class/net/<ice PF>/device/reset
Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu")
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Do not allow to acquire data or alter configuration of dpll and pins
through firmware if PF reset is in progress, this would cause confusing
netlink extack errors as the firmware cannot respond or process the
request properly during the reset time.
Return (-EBUSY) and extack error for the user who tries access/modify
the config of dpll/pin through firmware during the reset time.
The PF reset and kernel access to dpll data are both asynchronous. It is
not possible to guard all the possible reset paths with any determinictic
approach. I.e., it is possible that reset starts after reset check is
performed (or if the reset would be checked after mutex is locked), but at
the same time it is not possible to wait for dpll mutex unlock in the
reset flow.
This is best effort solution to at least give a clue to the user
what is happening in most of the cases, knowing that there are possible
race conditions where the user could see a different error received
from firmware due to reset unexpectedly starting.
Test by looping execution of below steps until netlink error appears:
- perform PF reset
$ echo 1 > /sys/class/net/<ice PF>/device/reset
- i.e. try to alter/read dpll/pin config:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--dump pin-get
Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The value of phase_adjust for input pin shall be updated in
ice_dpll_pin_state_update(..). Fix by adding proper argument to the
firmware query function call - a pin's struct field pointer where the
phase_adjust value during driver runtime is stored.
Previously the phase_adjust used to misinform user about actual
phase_adjust value. I.e., if phase_adjust was set to a non zero value and
if driver was reloaded, the user would see the value equal 0, which is
not correct - the actual value is equal to value set before driver reload.
Fixes: 90e1c90750d7 ("ice: dpll: implement phase related callbacks")
Reviewed-by: Alan Brady <alan.brady@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix the connection state between source DPLL and output pin, updating the
attribute 'state' of 'parent_device'. Previously, the connection state
was broken, and didn't reflect the correct state.
When 'state_on_dpll_set' is called with the value
'DPLL_PIN_STATE_CONNECTED' (1), the output pin will switch to the given
DPLL, and the state of the given DPLL will be set to connected.
E.g.:
--do pin-set --json '{"id":2, "parent-device":{"parent-id":1,
"state": 1 }}'
This command will connect DPLL device with id 1 to output pin with id 2.
When 'state_on_dpll_set' is called with the value
'DPLL_PIN_STATE_DISCONNECTED' (2) and the given DPLL is currently
connected, then the output pin will be disabled.
E.g:
--do pin-set --json '{"id":2, "parent-device":{"parent-id":1,
"state": 2 }}'
This command will disable output pin with id 2 if DPLL device with ID 1 is
connected to it; otherwise, the command is ignored.
Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Yochai Hagvi <yochai.hagvi@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
net/core/dev.c
9f30831390ed ("net: add rcu safety to rtnl_prop_list_size()")
723de3ebef03 ("net: free altname using an RCU callback")
net/unix/garbage.c
11498715f266 ("af_unix: Remove io_uring code for GC.")
25236c91b5ab ("af_unix: Fix task hung while purging oob_skb in GC.")
drivers/net/ethernet/renesas/ravb_main.c
ed4adc07207d ("net: ravb: Count packets instead of descriptors in GbEth RX path"
)
c2da9408579d ("ravb: Add Rx checksum offload support for GbEth")
net/mptcp/protocol.c
bdd70eb68913 ("mptcp: drop the push_pending field")
28e5c1380506 ("mptcp: annotate lockless accesses around read-mostly fields")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To fully support initializing the LAG support code, a DDP package that
extracts the logical port from the metadata is required. If such a
package is not present, there could be difficulties in supporting some
bond types.
Add a check into the initialization flow that will bypass the new paths
if any of the support pieces are missing.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Fixes: df006dd4b1dc ("ice: Add initial support framework for LAG")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240213183957.1483857-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During devlink reload it is needed to remove debugfs entries
correlated with only one PF. ice_debugfs_exit() removes all
entries created by ice driver so we can't use it.
Introduce ice_debugfs_pf_deinit() in order to release PF's
debugfs entries. Move ice_debugfs_exit() call to ice_module_exit(),
it makes more sense since ice_debugfs_init() is called in
ice_module_init() and not in ice_probe().
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Recent changes to the devlink reload (commit 9b2348e2d6c9
("devlink: warn about existing entities during reload-reinit"))
force the drivers to destroy devlink ports during reinit.
Adjust ice driver to this requirement, unregister netdvice, destroy
devlink port. ice_init_eth() was removed and all the common code
between probe and reload was moved to ice_load().
During devlink reload we can't take devl_lock (it's already taken)
and in ice_probe() we have to lock it. Use devl_* variant of the API
which does not acquire and release devl_lock. Guard ice_load()
with devl_lock only in case of probe.
Suggested-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E825C devices shall support the new signing type of RSA 3K for new DDP
section (SEGMENT_SIGN_TYPE_RSA3K_E825 (5) - already in the code).
The driver is responsible to verify the presence of correct signing type.
Add 3k signinig support for E825C devices based on mac_type:
ICE_MAC_GENERIC_3K_E825;
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E800 series devices have a couple of quirks:
1. Sideband control queues are not supported
2. The registers that the driver needs to program for the "Precision
Time Protocol (PTP)" feature are different for E800 series devices
compared to other devices supported by this driver.
Both these require conditional logic based on the underlying device we
are dealing with.
The function ice_is_sbq_supported added by commit 8f5ee3c477a8
("ice: add support for sideband messages") addresses (1).
The same function can be used to address (2) as well
but this just looks weird readability wise in cases that have nothing
to do with sideband control queues:
if (ice_is_sbq_supported(hw))
/* program register A */
else
/* program register B */
For these cases, the function ice_is_generic_mac introduced by this
patch communicates the idea/intention better. Also rework
ice_is_sbq_supported to use this new function.
As side-band queue is supported for E825C devices, it's mac_type is
considered as generic mac_type.
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Introduce new Intel Ethernet E825C family devices.
Add new PCI device IDs which are going to be supported by the
driver:
- 579C: Intel(R) Ethernet Connection E825-C for backplane
- 579D: Intel(R) Ethernet Connection E825-C for QSFP
- 579E: Intel(R) Ethernet Connection E825-C for SFP
- 579F: Intel(R) Ethernet Connection E825-C for SGMII
Add helper function ice_is_e825c() to verify if the running device
belongs to E825C family.
Co-developed-by: Jan Glaza <jan.glaza@intel.com>
Signed-off-by: Jan Glaza <jan.glaza@intel.com>
Co-developed-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/stmicro/stmmac/common.h
38cc3c6dcc09 ("net: stmmac: protect updates of 64-bit statistics counters")
fd5a6a71313e ("net: stmmac: est: Per Tx-queue error count for HLBF")
c5c3e1bfc9e0 ("net: stmmac: Offload queueMaxSDU from tc-taprio")
drivers/net/wireless/microchip/wilc1000/netdev.c
c9013880284d ("wifi: fill in MODULE_DESCRIPTION()s for wilc1000")
328efda22af8 ("wifi: wilc1000: do not realloc workqueue everytime an interface is added")
net/unix/garbage.c
11498715f266 ("af_unix: Remove io_uring code for GC.")
1279f9d9dec2 ("af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The kernel build regressions/improvements email contained a couple of
issues with old compilers (in fact all the reports were on different
architectures, but all gcc 5.5) and the FIELD_PREP() and FIELD_GET()
conversions. They're all because an integer #define that should have
been declared as unsigned, was shifted to the point that it could set
the sign bit.
The fix just involves making sure the defines use the "U" identifier on
the constants to make sure they're unsigned. Should make the checkers
happier.
Confirmed with objdump before/after that there is no change to the
binaries.
Issues were reported as follows:
./drivers/net/ethernet/intel/ice/ice_base.c:238:7: note: in expansion of macro 'FIELD_GET'
(FIELD_GET(GLINT_CTL_ITR_GRAN_25_M, regval) == ICE_ITR_GRAN_US))
^
./include/linux/compiler_types.h:435:38: error: call to '__compiletime_assert_1093' declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_nvm.c:709:16: note: in expansion of macro ‘FIELD_GET’
orom->major = FIELD_GET(ICE_OROM_VER_MASK, combo_ver);
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_796’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_common.c:945:18: note: in expansion of macro ‘FIELD_GET’
u8 max_agg_bw = FIELD_GET(GL_PWR_MODE_CTL_CAR_MAX_BW_M,
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_420’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/i40e/i40e_dcb.c:458:8: note: in expansion of macro ‘FIELD_GET’
oui = FIELD_GET(I40E_LLDP_TLV_OUI_MASK, ouisubtype);
^
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/lkml/d03e90ca-8485-4d1b-5ec1-c3398e0e8da@linux-m68k.org/ #i40e #ice
Fixes: 62589808d73b ("i40e: field get conversion")
Fixes: 5a259f8e0baf ("ice: field get conversion")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20240206022906.2194214-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Copy paste issue left a comment for this structure that has nothing
to do with FW alignment; remove the comment.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
HW incorrectly reports EIPE errors on encapsulated packets
with L2 padding inside inner packet. HW shows outer UDP/IPV4
packet checksum errors as part of the EIPE flags of the
Rx descriptor. These are reported only if checksum offload
is enabled and L3/L4 parsed flag is valid in Rx descriptor.
When that error is reported by HW, we don't act on it
instead of incrementing main Rx errors statistic as it
would normally happen.
Add a new statistic to count these errors since we still want
to print them.
Signed-off-by: Aniruddha Paul <aniruddha.paul@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jan Glaza <jan.glaza@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently, XSK control path in ice driver calls directly
ice_vsi_cfg_txq() whereas we have ice_vsi_cfg_single_txq() for that
purpose. Use the latter from XSK side and make ice_vsi_cfg_txq() static.
ice_vsi_cfg_txq() resides in ice_base.c and is rather big, so to reduce
the code churn let us move the callers of it from ice_lib.c to
ice_base.c.
This change puts ice_qp_ena() on nice diet due to the checks and
operations that ice_vsi_cfg_single_{r,t}xq() do internally.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-182 (-182)
Function old new delta
ice_xsk_pool_setup 2165 1983 -182
Total: Before=472597, After=472415, chg -0.04%
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently, XSK control path in ice driver calls directly
ice_vsi_cfg_rxq() whereas we have ice_vsi_cfg_single_rxq() for that
purpose. Use the latter from XSK side and make ice_vsi_cfg_rxq() static.
ice_vsi_cfg_rxq() resides in ice_base.c and is rather big, so to reduce
the code churn let us move two callers of it from ice_lib.c to
ice_base.c.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Pass additional argunent status_error over lock_status_get()
so drivers can fill it up. In case they do, expose the value over
previously introduced attribute to user. Do it only in case the
current lock_status is either "unlocked" or "holdover".
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The ice driver currently attempts to destroy and re-initialize the Tx
timestamp tracker during the reset flow. The release of the Tx tracker
only happened during CORE reset or GLOBAL reset. The ice_ptp_rebuild()
function always calls the ice_ptp_init_tx function which will allocate
a new tracker data structure, resulting in memory leaks during PF reset.
Certainly the driver should not be allocating a new tracker without
removing the old tracker data, as this results in a memory leak.
Additionally, there's no reason to remove the tracker memory during a
reset. Remove this logic from the reset and rebuild flow. Instead of
releasing the Tx tracker, flush outstanding timestamps just before we
reset the PHY timestamp block in ice_ptp_cfg_phy_interrupt().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The ice_ptp_reset() function uses a goto to skip past clock owner
operations if performing a PF reset or if the device is not the clock
owner. This is a bit confusing. Factor this out into
ice_ptp_rebuild_owner() instead.
The ice_ptp_reset() function is called by ice_rebuild() to restore PTP
functionality after a device reset. Follow the convention set by the
ice_main.c file and rename this function to ice_ptp_rebuild(), in the
same way that we have ice_prepare_for_reset() and
ice_ptp_prepare_for_reset().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The ice_ptp_tx_cfg_intr() function sends a control queue message to
configure the PHY timestamp interrupt block. This is a very similar name
to a function which is used to configure the MAC Other Interrupt Cause
Enable register.
Rename this function to ice_ptp_cfg_phy_interrupt in order to make it
more obvious to the reader what action it performs, and distinguish it
from other similarly named functions.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
E810 hardware does not have a Tx timestamp ready bitmap. Don't check
has_ready_bitmap in E810-specific functions.
Add has_ready_bitmap check in ice_ptp_process_tx_tstamp() to stop
relying on the fact that ice_get_phy_tx_tstamp_ready() returns all 1s.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The tx->verify_cached flag is used to inform the Tx timestamp tracking
code whether it needs to verify the cached Tx timestamp value against
a previous captured value. This is necessary on E810 hardware which does
not have a Tx timestamp ready bitmap.
In addition, we currently rely on the fact that the
ice_get_phy_tx_tstamp_ready() function returns all 1s for E810 hardware.
Instead of introducing a brand new flag, rename and verify_cached to
has_ready_bitmap, inverting the relevant checks.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The ice_ptp_prepare_for_reset() and ice_ptp_reset() functions currently
check the pf->flags ICE_FLAG_PFR_REQ bit to determine if the current
reset is a PF reset or not.
This is problematic, because it is possible that a PF reset and a higher
level reset (CORE reset, GLOBAL reset, EMP reset) are requested
simultaneously. In that case, the driver performs the highest level
reset requested. However, the ICE_FLAG_PFR_REQ flag will still be set.
The main driver reset functions take an enum ice_reset_req indicating
which reset is actually being performed. Pass this data into the PTP
functions and rely on this instead of relying on the driver flags.
This ensures that the PTP code performs the proper level of reset that
the driver is actually undergoing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add PTP state machine so that the driver can correctly identify PTP
state around resets.
When the driver got information about ungraceful reset, PTP was not
prepared for reset and it returned error. When this situation occurs,
prepare PTP before rebuilding its structures.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Now that ice driver correctly sets up frag_size in xdp_rxq_info, let us
make it work for ZC multi-buffer as well. ice_rx_ring::rx_buf_len for ZC
is being set via xsk_pool_get_rx_frame_size() and this needs to be
propagated up to xdp_rxq_info.
Use a bigger hammer and instead of unregistering only xdp_rxq_info's
memory model, unregister it altogether and register it again and have
xdp_rxq_info with correct frag_size value.
Fixes: 1bbc04de607b ("ice: xsk: add RX multi-buffer support")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-9-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Ice and i40e ZC drivers currently set offset of a frag within
skb_shared_info to 0, which is incorrect. xdp_buffs that come from
xsk_buff_pool always have 256 bytes of a headroom, so they need to be
taken into account to retrieve xdp_buff::data via skb_frag_address().
Otherwise, bpf_xdp_frags_increase_tail() would be starting its job from
xdp_buff::data_hard_start which would result in overwriting existing
payload.
Fixes: 1c9ba9c14658 ("i40e: xsk: add RX multi-buffer support")
Fixes: 1bbc04de607b ("ice: xsk: add RX multi-buffer support")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-8-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
