| Age | Commit message (Collapse) | Author |
|---|
|
qca8081 PHY supports to use genphy_c45_pma_read_abilities for
getting the PHY features supported except for the autoneg ability
but autoneg ability exists in MDIO_STAT1 instead of MMD7.1, add it
manually after calling genphy_c45_pma_read_abilities.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
74165 is a 16nm process SoC with a 10/100 integrated Ethernet PHY,
utilize the recently defined 16nm EPHY macro to configure that PHY.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the following unlocked accessors to complete the set:
__mdiobus_modify()
__mdiodev_read()
__mdiodev_write()
__mdiodev_modify()
__mdiodev_modify_changed()
which we will need for Marvell DSA PCS conversion.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a function, phylink_pcs_change() which can be used by PCs drivers
to notify phylink about changes to the PCS link state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add hooks that are called before and after the mac_config() call,
which will be needed to deal with errata workarounds for the
Marvell 88e639x DSA switches.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add phylink PCS enable/disable callbacks that will allow us to place
IEEE 802.3 register compliant PCS in power-down mode while not being
used.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge in late fixes to prepare for the 6.5 net-next PR.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Two deadly typos break RX and TX traffic on the VSC8502 PHY using RGMII
if phy-mode = "rgmii-id" or "rgmii-txid", and no "tx-internal-delay-ps"
override exists. The negative error code from phy_get_internal_delay()
does not get overridden with the delay deduced from the phy-mode, and
later gets committed to hardware. Also, the rx_delay gets overridden by
what should have been the tx_delay.
Fixes: dbb050d2bfc8 ("phy: mscc: Add support for RGMII delay configuration")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Harini Katakam <harini.katakam@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230627134235.3453358-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Linux provides phy_set_bits() helper so let's drop brcm_phy_setbits() and
use phy_set_bits() in its place.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230622184721.24368-1-giulio.benetti@benettiengineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix an issue where the kernel would stall during netboot, showing the
"sched: RT throttling activated" message. This stall was triggered by
the behavior of the mii_interrupt bit (Bit 7 - DP83TD510E_STS_MII_INT)
in the DP83TD510E's PHY_STS Register (Address = 0x10). The DP83TD510E
datasheet (2020) states that the bit clears on write, however, in
practice, the bit clears on read.
This discrepancy had significant implications on the driver's interrupt
handling. The PHY_STS Register was used by handle_interrupt() to check
for pending interrupts and by read_status() to get the current link
status. The call to read_status() was unintentionally clearing the
mii_interrupt status bit without deasserting the IRQ pin, causing
handle_interrupt() to miss other pending interrupts. This issue was most
apparent during netboot.
The fix refrains from using the PHY_STS Register for interrupt handling.
Instead, we now solely rely on the INTERRUPT_REG_1 Register (Address =
0x12) and INTERRUPT_REG_2 Register (Address = 0x13) for this purpose.
These registers directly influence the IRQ pin state and are latched
high until read.
Note: The INTERRUPT_REG_2 Register (Address = 0x13) exists and can also
be used for interrupt handling, specifically for "Aneg page received
interrupt" and "Polarity change interrupt". However, these features are
currently not supported by this driver.
Fixes: 165cd04fe253 ("net: phy: dp83td510: Add support for the DP83TD510 Ethernet PHY")
Cc: <stable@vger.kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230621043848.3806124-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert fman_dtsec, xilinx_axienet and pcs-lynx to pass the neg_mode
into phylink_mii_c22_pcs_config(). Where appropriate, drivers are
updated to have neg_mode passed into their pcs_config() and
pcs_link_up() functions. For other drivers, we just hoist the call
to phylink_pcs_neg_mode() to their pcs_config() method out of
phylink_mii_c22_pcs_config().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Do-00EaFM-Ra@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use phylink_pcs_neg_mode() for phylink_mii_c22_pcs_config(). This
results in no functional change.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dj-00EaFG-Mt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PCS have to work out whether they should enable PCS negotiation by
looking at the "mode" and "interface" arguments, and the Autoneg bit
in the advertising mask.
This leads to some complex logic, so lets pull that out into phylink
and instead pass a "neg_mode" argument to the PCS configuration and
link up methods, instead of the "mode" argument.
In order to transition drivers, add a "neg_mode" flag to the phylink
PCS structure to PCS can indicate whether they want to be passed the
neg_mode or the old mode argument.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8De-00EaFA-Ht@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
tools/testing/selftests/net/fcnal-test.sh
d7a2fc1437f7 ("selftests: net: fcnal-test: check if FIPS mode is enabled")
dd017c72dde6 ("selftests: fcnal: Test SO_DONTROUTE on TCP sockets.")
https://lore.kernel.org/all/5007b52c-dd16-dbf6-8d64-b9701bfa498b@tessares.net/
https://lore.kernel.org/all/20230619105427.4a0df9b3@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently for each timestamp frame, the SW needs to go and read the
received timestamp over the MDIO bus. But the HW has the capability
to store the received nanoseconds part and the least significant two
bits of the seconds in the reserved field of the PTP header. In this
way we could save few MDIO transactions (actually a little more
transactions because the access to the PTP registers are indirect)
for each received frame.
Instead of reading the rest of seconds part of the timestamp of the
frame using MDIO transactions schedule PTP worker thread to read the
seconds part every 500ms and then for each of the received frames use
this information. Because if for example running with 512 frames per
second, there is no point to read 512 times the second part.
Doing all these changes will give a great CPU usage performance.
Running ptp4l with logSyncInterval of -9 will give a ~60% CPU
improvement.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The text has been cut/paste from genphy_c45_ethtool_get_eee but not
changed to reflect it performs set.
Additionally, extend the comment. This function implements the logic
that eee_enabled has global control over EEE. When eee_enabled is
false, no link modes will be advertised, and as a result, the MAC
should not transmit LPI.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230619220332.4038924-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit da9ef50f545f86ffe6ff786174d26500c4db737a.
This fixes a regression in which the link would come up, but no
communication was possible.
The reverted commit was also removing a comment about
DP83867_PHYCR_FORCE_LINK_GOOD, this is not added back in this commits
since it seems that this is unrelated to the original code change.
Closes: https://lore.kernel.org/all/ZGuDJos8D7N0J6Z2@francesco-nb.int.toradex.com/
Fixes: da9ef50f545f ("net: phy: dp83867: perform soft reset and retain established link")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Link: https://lore.kernel.org/r/20230619154435.355485-1-francesco@dolcini.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PHY address and device address are passed in the wrong order.
Cc: stable@vger.kernel.org
Fixes: 4e4aafcddbbf ("net: mdio: Add dedicated C45 API to MDIO bus drivers")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230619094948.84452-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The new phy driver attempts to select a driver from another subsystem,
but that fails when the NVMEM subsystem is disabled:
WARNING: unmet direct dependencies detected for NVMEM_MTK_EFUSE
Depends on [n]: NVMEM [=n] && (ARCH_MEDIATEK [=n] || COMPILE_TEST [=y]) && HAS_IOMEM [=y]
Selected by [y]:
- MEDIATEK_GE_SOC_PHY [=y] && NETDEVICES [=y] && PHYLIB [=y] && (ARM64 && ARCH_MEDIATEK [=n] || COMPILE_TEST [=y])
I could not see an actual compile time dependency, so presumably this
is only needed for for working correctly but not technically a dependency
on that particular nvmem driver implementation, so it would likely
be safe to remove the select for compile testing.
To keep the spirit of the original 'select', just replace this with a
'depends on' that ensures that the driver will work but does not get in
the way of build testing.
Fixes: 98c485eaf509b ("net: phy: add driver for MediaTek SoC built-in GE PHYs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230616093009.3511692-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use devm_regulator_get_enable_optional() instead of hand writing it. It
saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the core is left to remove the LEDs via devm_, it is performed too
late, after the PHY driver is removed from the PHY. This results in
dereferencing a NULL pointer when the LED core tries to turn the LED
off before destroying the LED.
Manually unregister the LEDs at a safe point in phy_remove.
Cc: stable@vger.kernel.org
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 01e5b728e9e4 ("net: phy: Add a binding for PHY LEDs")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
include/linux/mlx5/driver.h
617f5db1a626 ("RDMA/mlx5: Fix affinity assignment")
dc13180824b7 ("net/mlx5: Enable devlink port for embedded cpu VF vports")
https://lore.kernel.org/all/20230613125939.595e50b8@canb.auug.org.au/
tools/testing/selftests/net/mptcp/mptcp_join.sh
47867f0a7e83 ("selftests: mptcp: join: skip check if MIB counter not supported")
425ba803124b ("selftests: mptcp: join: support RM_ADDR for used endpoints or not")
45b1a1227a7a ("mptcp: introduces more address related mibs")
0639fa230a21 ("selftests: mptcp: add explicit check for new mibs")
https://lore.kernel.org/netdev/20230609-upstream-net-20230610-mptcp-selftests-support-old-kernels-part-3-v1-0-2896fe2ee8a3@tessares.net/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Q-USGMII is a derivative of USGMII, that uses a specific formatting for
the control word. The layout is close to the USXGMII control word, but
doesn't support speeds over 1Gbps. Use a dedicated decoding logic for
the USGMII control word, re-using USXGMII definitions but only considering
10/100/1000Mbps speeds
Fixes: 5e61fe157a27 ("net: phy: Introduce QUSGMII PHY mode")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Q-USGMII is the quad port version of USGMII, and supports a max speed of
1Gbps on each line. Make so that phylink_interface_max_speed() reports
this information correctly.
Fixes: ae0e4bb2a0e0 ("net: phylink: Adjust link settings based on rate matching")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some of MediaTek's Filogic SoCs come with built-in gigabit Ethernet
PHYs which require calibration data from the SoC's efuse.
Despite the similar design the driver doesn't share any code with the
existing mediatek-ge.c.
Add support for such PHYs by introducing a new driver with basic
support for MediaTek SoCs MT7981 and MT7988 built-in 1GE PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Broadcom PHYs have two LEDs selector registers which allow us to control
the LED assignment, including how to turn them on/off.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These registers are common to most PHYs and are not specific to the
BCM5482, renamed the constants accordingly, no functional change.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/sch_taprio.c
d636fc5dd692 ("net: sched: add rcu annotations around qdisc->qdisc_sleeping")
dced11ef84fb ("net/sched: taprio: don't overwrite "sch" variable in taprio_dump_class_stats()")
net/ipv4/sysctl_net_ipv4.c
e209fee4118f ("net/ipv4: ping_group_range: allow GID from 2147483648 to 4294967294")
ccce324dabfe ("tcp: make the first N SYN RTO backoffs linear")
https://lore.kernel.org/all/20230605100816.08d41a7b@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For PHYs that call rtl821x_probe() where an external clock can be
configured, make sure that the clock is disabled
when ->suspend() is called and enabled on resume.
The PHY_ALWAYS_CALL_SUSPEND is added to ensure that the suspend function
is actually always called.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases, the PHY can use an external clock source instead of a
crystal.
Add an optional clock in the phy node to make sure that the clock source
is enabled, if specified, before probing.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ksz9477 DSA switch driver is currently updating some MMD registers
on the internal port PHYs to address some chip errata. However, these
errata are really a property of the PHY itself, not the switch they are
part of, so this is kind of a layering violation. It makes more sense for
these writes to be done inside the driver which binds to the PHY and not
the driver for the containing device.
This also addresses some issues where the ordering of when these writes
are done may have been incorrect, causing the link to erratically fail to
come up at the proper speed or at all. Doing this in the PHY driver
during config_init ensures that they happen before anything else tries to
change the state of the PHY on the port.
The new code also ensures that autonegotiation is disabled during the
register writes and re-enabled afterwards, as indicated by the latest
version of the errata documentation from Microchip.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Raju Lakkaraju reported that the below commit caused a regression
with Lan743x drivers and a 2.5G SFP. Sadly, this is because the commit
was utterly wrong. Let's fix this properly by not moving the
linkmode_and(), but instead copying the link ksettings and then
modifying the advertising mask before passing the modified link
ksettings to phylib.
Fixes: df0acdc59b09 ("net: phylink: fix ksettings_set() ethtool call")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1q4eLm-00Ayxk-GZ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the ability to read the PHY maintained LPI counter which is in the
Clause 45 vendor space, device address 7, offset 0x803F. The counter is
cleared on read.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230531231729.1873932-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/sfc/tc.c
622ab656344a ("sfc: fix error unwinds in TC offload")
b6583d5e9e94 ("sfc: support TC decap rules matching on enc_src_port")
net/mptcp/protocol.c
5b825727d087 ("mptcp: add annotations around msk->subflow accesses")
e76c8ef5cc5b ("mptcp: refactor mptcp_stream_accept()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The interrupt fix in commit 97a89ed101bb should be applied on all variants
of GPY2xx PHY and GPY115C.
Fixes: 97a89ed101bb ("net: phy: mxl-gpy: disable interrupts on GPY215 by default")
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230531074822.39136-1-lxu@maxlinear.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for optional rx/tx-internal-delay-ps from devicetree.
- When rx/tx-internal-delay-ps is/are specified, these take priority
- When either is absent,
1) use 2ns for respective settings if rgmii-id/rxid/txid is/are present
2) use 0.2ns for respective settings if mode is rgmii
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All the PHY devices variants specified have the same mask and
hence can be simplified to one vendor look up for 0x00070400.
Any individual config can be identified by PHY_ID_MATCH_EXACT
in the respective structure.
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the Microchip LAN865x Rev.B0 10BASE-T1S Internal PHYs
(LAN8650/1). The LAN865x combines a Media Access Controller (MAC) and an
internal 10BASE-T1S Ethernet PHY to access 10BASE‑T1S networks. As
LAN867X and LAN865X are using the same function for the read_status,
rename the function as lan86xx_read_status.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
By default, except Reset Complete interrupt in the Interrupt Mask 2
Register all other interrupts are disabled/masked. As Reset Complete
status is already handled, it doesn't make sense to disable it.
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Tested-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As per the datasheet DS-LAN8670-1-2-60001573C.pdf, the Reset Complete
status bit in the STS2 register has to be checked before proceeding to
the initial configuration. Reading STS2 register will also clear the
Reset Complete interrupt which is non-maskable.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Tested-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As per AN1699, the initial configuration in the driver applies to LAN867x
Rev.B1 hardware revision. 0x0007C160 (Rev.A0) and 0x0007C161 (Rev.B0)
never released to production and hence they don't need to be supported.
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Replace read-modify-write code in the lan867x_config_init function to
avoid handling data type mismatch and to simplify the code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove LAN867X from the driver description as this driver is common for
all the Microchip 10BASE-T1S PHYs.
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In order to have our interrupt descriptor fully setup and in particular
the action, ensure that we register a full fledged interrupt handler.
This also allow us to set the interrupt polarity and flow through the
same call.
This is specifically necessary for kernel/irq/pm.c::suspend_device_irq
to set the interrupt descriptor to the IRQD_WAKEUP_ARMED state and
enable the interrupt for wake-up since it was still in a disabled state.
Without an interrupt descriptor we would have ran into cases where the
wake-up interrupt is not capable of waking up the system, specifically
if we resumed the system ACPI S5 using the Ethernet PHY. In that case
the Ethernet PHY interrupt would be pending by the time the kernel
booted, which it would acknowledge but then we could never use it as
a wake-up source again.
Fixes: 8baddaa9d4ba ("net: phy: broadcom: Add support for Wake-on-LAN")
Suggested-by: Doug Berger <doug.berger@broadcom.com>
Debugged-by: Doug Berger <doug.berger@broadcom.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/ipv4/raw.c
3632679d9e4f ("ipv{4,6}/raw: fix output xfrm lookup wrt protocol")
c85be08fc4fa ("raw: Stop using RTO_ONLINK.")
https://lore.kernel.org/all/20230525110037.2b532b83@canb.auug.org.au/
Adjacent changes:
drivers/net/ethernet/freescale/fec_main.c
9025944fddfe ("net: fec: add dma_wmb to ensure correct descriptor values")
144470c88c5d ("net: fec: using the standard return codes when xdp xmit errors")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add two helper functions for calling PCS methods. phylink_pcs_config()
allows us to handle PCS configuration specifics in one location, rather
than the two call sites. phylink_pcs_link_up() gives us consistency.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1q1TzK-007Exd-Rs@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
By default the VSC8501 and VSC8502 RGMII/GMII/MII RX_CLK output is
disabled. To allow packet forwarding towards the MAC it needs to be
enabled.
For other PHYs supported by this driver the clock output is enabled
by default.
Fixes: d3169863310d ("net: phy: mscc: add support for VSC8502")
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Holding the struct phy_device (phydev) lock is unnecessary when
accessing phydev->interface in the PHY driver .config_init method,
which is the only place that vsc85xx_rgmii_set_skews() is called from.
The phy_modify_paged() function implements required MDIO bus level
locking, which can not be achieved by a phydev lock.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VSC8501 PHY can use the same driver implementation as the VSC8502.
Adding the PHY ID and copying the handler functions of VSC8502 is
sufficient to operate it.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mscc driver implements support for VSC8502, so its ID should be in
the MODULE_DEVICE_TABLE for automatic loading.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Fixes: d3169863310d ("net: phy: mscc: add support for VSC8502")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
