summaryrefslogtreecommitdiff
path: root/drivers/pci/controller
AgeCommit message (Collapse)Author
2022-03-10PCI: fu740: Drop redundant '-gpios' from DT GPIO lookupBen Dooks
The calls to devm_gpiod_get_optional() have the -gpios at the end of the name but the GPIO core code is already adding the suffix during the lookup. This means the PCIe driver is not finding the necessary reset or power lines to allow initialisation of the PCIe. Drop the redundant '-gpios' when we look up GPIOs from the DT. This bug has not been noticed because if U-Boot has setup the GPIO lines for the hardware when it does the PCIe initialisation (either by booting from PCIe or user command to access PCIe) then the PCIe will work in Linux. The U-Boot as supplied by SiFive does not by default initialise any PCIe component. Link: https://lore.kernel.org/r/20220221210347.1335004-1-ben.dooks@codethink.co.uk Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-03-10PCI: apple: Change MSI handling to handle 4-cell AIC fwspec formHector Martin
AIC2 changes the IRQ fwspec to add a cell. Always use the second-to-last cell for the MSI handling, so it will work for both AIC1 and AIC2 devices. Signed-off-by: Hector Martin <marcan@marcan.st> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20220309192123.152028-2-marcan@marcan.st
2022-03-07PCI: imx6: Enable i.MX6QP PCIe power management supportRichard Zhu
i.MX6QP PCIe supports the reset logic, thus it can reset itself to the initialized state when exit from L2 or L3 states. Enable the i.MX6QP PCIe suspend/resume operations support. Link: https://lore.kernel.org/r/1645425237-4071-2-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-03-02PCI: hv: Avoid the retarget interrupt hypercall in irq_unmask() on ARM64Boqun Feng
On ARM64 Hyper-V guests, SPIs are used for the interrupts of virtual PCI devices, and SPIs can be managed directly via GICD registers. Therefore the retarget interrupt hypercall is not needed on ARM64. An arch-specific interface hv_arch_irq_unmask() is introduced to handle the architecture level differences on this. For x86, the behavior remains unchanged, while for ARM64 no hypercall is invoked when unmasking an irq for virtual PCI devices. Link: https://lore.kernel.org/r/20220217034525.1687678-1-boqun.feng@gmail.com Signed-off-by: Boqun Feng <boqun.feng@gmail.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com>
2022-02-27Merge tag 'irq-urgent-2022-02-27' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq fix from Thomas Gleixner: "A single fix for a regression caused by the recent PCI/MSI rework which resulted in a recursive locking problem in the VMD driver. The cure is to cache the relevant information upfront instead of retrieving it at runtime" * tag 'irq-urgent-2022-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: PCI: vmd: Prevent recursive locking on interrupt allocation
2022-02-25Revert "PCI: aardvark: Fix initialization with old Marvell's Arm Trusted ↵Pali Rohár
Firmware" This reverts commit b0c6ae0f8948a2be6bf4e8b4bbab9ca1343289b6. Armada 3720 phy driver (phy-mvebu-a3700-comphy.c) does not return -EOPNOTSUPP from phy_power_on() callback anymore. So remove dead code which handles -EOPNOTSUPP return value. Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Link: https://lore.kernel.org/r/20220203214444.1508-6-kabel@kernel.org Signed-off-by: Vinod Koul <vkoul@kernel.org>
2022-02-24Merge tag 'pci-v5.17-fixes-5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull pci fixes from Bjorn Helgaas: - Fix a merge error that broke PCI device enumeration on mvebu platforms, including Turris Omnia (Armada 385) (Pali Rohár) - Avoid using ATS on all AMD Navi10 and Navi14 GPUs because some VBIOSes don't account for "harvested" (disabled) parts of the chip when initializing caches (Alex Deucher) * tag 'pci-v5.17-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: Mark all AMD Navi10 and Navi14 GPU ATS as broken PCI: mvebu: Fix device enumeration regression
2022-02-24sizes.h: Add SZ_1T macroChristophe Leroy
Today drivers/pci/controller/pci-xgene.c defines SZ_1T Move it into linux/sizes.h so that it can be re-used elsewhere. Link: https://lore.kernel.org/r/575cb7164cf124c75df7cb9242ea7374733942bf.1642752946.git.christophe.leroy@csgroup.eu Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Krzysztof Wilczyński <kw@linux.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Toan Le <toan@os.amperecomputing.com> Cc: linux-pci@vger.kernel.org
2022-02-23PCI: qcom: Add SM8450 PCIe supportDmitry Baryshkov
On SM8450 platform PCIe hosts do not use all the clocks (and add several additional clocks), so expand the driver to handle these requirements. PCIe0 and PCIe1 hosts use different sets of clocks, so separate entries are required. Link: https://lore.kernel.org/r/20220223101435.447839-5-dmitry.baryshkov@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
2022-02-23PCI: qcom: Add ddrss_sf_tbu flagDmitry Baryshkov
Qualcomm PCIe driver uses compatible string to check if the ddrss_sf_tbu clock should be used. Since sc7280 support has added flags, switch to the new mechanism to check if this clock should be used. Link: https://lore.kernel.org/r/20220223101435.447839-4-dmitry.baryshkov@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
2022-02-23PCI: qcom: Remove redundancy between qcom_pcie and qcom_pcie_cfgDmitry Baryshkov
In preparation to adding more flags to configuration data, use pointer to struct qcom_pcie_cfg directly inside struct qcom_pcie, rather than duplicating all its fields. This would save us from the boilerplate code that just copies flag values from one struct to another one. Link: https://lore.kernel.org/r/20220223101435.447839-3-dmitry.baryshkov@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
2022-02-22PCI: mvebu: Implement support for legacy INTx interruptsPali Rohár
This adds support for legacy INTx interrupts received from other PCIe devices and which are reported by a new INTx irq chip. With this change, kernel can distinguish between INTA, INTB, INTC and INTD interrupts. Note that for this support, device tree files has to be properly adjusted to provide "interrupts" or "interrupts-extended" property with intx interrupt source, "interrupt-names" property with "intx" string and also 'interrupt-controller' subnode must be defined. If device tree files do not provide these nodes then driver would work as before. Link: https://lore.kernel.org/r/20220222155030.988-12-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-22PCI: mvebu: Fix macro names and comments about legacy interruptsPali Rohár
Register 0x1910 unmasks interrupts and legacy INTx interrupts are unmasked because driver does not support individual masking yet. Link: https://lore.kernel.org/r/20220222155030.988-11-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-22PCI: mvebu: Use child_ops APIPali Rohár
Split struct pci_ops between ops and child_ops. Member ops is used for accessing PCIe Root Ports via pci-bridge-emul.c driver and child_ops for accessing real PCIe cards. There is no need to mix these two struct pci_ops into one as PCI core code already provides separate callbacks via bridge->ops and bridge->child_ops. Link: https://lore.kernel.org/r/20220222155030.988-9-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-22PCI: mvebu: Add support for Advanced Error Reporting registers on emulated ↵Pali Rohár
bridge AER registers start at mvebu offset 0x0100. Registers PCI_ERR_ROOT_COMMAND, PCI_ERR_ROOT_STATUS and PCI_ERR_ROOT_ERR_SRC are not supported on pre-XP hardware and returns zeros. Note that AER interrupt is not supported yet as mvebu emulated bridge does not implement interrupts support at all yet. Also remove custom macro PCIE_HEADER_LOG_4_OFF as it is unused and correctly this register should be referenced via standard macros with offset, e.g. as: PCIE_CAP_PCIERR_OFF + PCI_ERR_HEADER_LOG + 4. Link: https://lore.kernel.org/r/20220222155030.988-8-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-22PCI: mvebu: Add support for PCI Bridge Subsystem Vendor ID on emulated bridgePali Rohár
Register with Subsystem Device/Vendor ID is at offset 0x2c. Export is via emulated bridge. After this change Subsystem ID is visible in lspci output at line: Capabilities: [40] Subsystem Link: https://lore.kernel.org/r/20220222155030.988-7-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-22PCI: mvebu: Correctly configure x1/x4 modePali Rohár
If x1/x4 mode is not set correctly then link with endpoint card is not established. Use DTS property 'num-lanes' to deteriminate x1/x4 mode. Link: https://lore.kernel.org/r/20220222155030.988-6-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-21PCI: vmd: Prevent recursive locking on interrupt allocationThomas Gleixner
Tejas reported the following recursive locking issue: swapper/0/1 is trying to acquire lock: ffff8881074fd0a0 (&md->mutex){+.+.}-{3:3}, at: msi_get_virq+0x30/0xc0 but task is already holding lock: ffff8881017cd6a0 (&md->mutex){+.+.}-{3:3}, at: __pci_enable_msi_range+0xf2/0x290 stack backtrace: __mutex_lock+0x9d/0x920 msi_get_virq+0x30/0xc0 pci_irq_vector+0x26/0x30 vmd_msi_init+0xcc/0x210 msi_domain_alloc+0xbf/0x150 msi_domain_alloc_irqs_descs_locked+0x3e/0xb0 __pci_enable_msi_range+0x155/0x290 pci_alloc_irq_vectors_affinity+0xba/0x100 pcie_port_device_register+0x307/0x550 pcie_portdrv_probe+0x3c/0xd0 pci_device_probe+0x95/0x110 This is caused by the VMD MSI code which does a lookup of the Linux interrupt number for an VMD managed MSI[X] vector. The lookup function tries to acquire the already held mutex. Avoid that by caching the Linux interrupt number at initialization time instead of looking it up over and over. Fixes: 82ff8e6b78fc ("PCI/MSI: Use msi_get_virq() in pci_get_vector()") Reported-by: "Surendrakumar Upadhyay, TejaskumarX" <tejaskumarx.surendrakumar.upadhyay@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: "Surendrakumar Upadhyay, TejaskumarX" <tejaskumarx.surendrakumar.upadhyay@intel.com> Cc: linux-pci@vger.kernel.org Link: https://lore.kernel.org/r/87a6euub2a.ffs@tglx
2022-02-17PCI: iproc: Set all 24 bits of PCI class codePali Rohár
Register 0x43c in its low 24 bits contains PCI class code. Update code to set all 24 bits of PCI class code and not only upper 16 bits of PCI class code. Use a new macro PCI_CLASS_BRIDGE_PCI_NORMAL which represents whole 24 bits of normal PCI bridge class. Link: https://lore.kernel.org/r/20220214114109.26809-2-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Roman Bacik <roman.bacik@broadcom.com> Acked-by: Ray Jui <ray.jui@broadcom.com>
2022-02-17PCI: Add defines for normal and subtractive PCI bridgesPali Rohár
Add these PCI class codes to pci_ids.h: PCI_CLASS_BRIDGE_PCI_NORMAL PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE Use these defines in all kernel code for describing PCI class codes for normal and subtractive PCI bridges. [bhelgaas: similar change in pci-mvebu.c] Link: https://lore.kernel.org/r/20220214114109.26809-1-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-02-15Merge tag 'hyperv-fixes-signed-20220215' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux Pull hyperv fixes from Wei Liu: - Rework use of DMA_BIT_MASK in vmbus to work around a clang bug (Michael Kelley) - Fix NUMA topology (Long Li) - Fix a memory leak in vmbus (Miaoqian Lin) - One minor clean-up patch (Cai Huoqing) * tag 'hyperv-fixes-signed-20220215' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: Drivers: hv: utils: Make use of the helper macro LIST_HEAD() Drivers: hv: vmbus: Rework use of DMA_BIT_MASK(64) Drivers: hv: vmbus: Fix memory leak in vmbus_add_channel_kobj PCI: hv: Fix NUMA node assignment when kernel boots with custom NUMA topology
2022-02-14PCI: mvebu: Fix device enumeration regressionPali Rohár
Jan reported that on Turris Omnia (Armada 385), no PCIe devices were detected after upgrading from v5.16.1 to v5.16.3 and identified the cause as the backport of 91a8d79fc797 ("PCI: mvebu: Fix configuring secondary bus of PCIe Root Port via emulated bridge"), which appeared in v5.17-rc1. 91a8d79fc797 was incorrectly applied from mailing list patch [1] to the linux git repository [2] probably due to resolving merge conflicts incorrectly. Fix it now. [1] https://lore.kernel.org/r/20211125124605.25915-12-pali@kernel.org [2] https://git.kernel.org/linus/91a8d79fc797 [bhelgaas: commit log] BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215540 Fixes: 91a8d79fc797 ("PCI: mvebu: Fix configuring secondary bus of PCIe Root Port via emulated bridge") Link: https://lore.kernel.org/r/20220214110228.25825-1-pali@kernel.org Link: https://lore.kernel.org/r/20220127234917.GA150851@bhelgaas Reported-by: Jan Palus <jpalus@fastmail.com> Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-02-11PCI: uniphier-ep: Add NX1 supportKunihiko Hayashi
Add basic support for UniPhier NX1 SoC as non-legacy SoC. This includes a compatible string, SoC-dependent data containing init() and wait() functions for the controller. Link: https://lore.kernel.org/r/1644480596-20037-4-git-send-email-hayashi.kunihiko@socionext.com Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Rob Herring <robh@kernel.org>
2022-02-11PCI: uniphier-ep: Add SoC data structureKunihiko Hayashi
Define SoC data structure that includes pci_epc_features, SoC-dependent callback functions and flags to distinguish the behavior of each SoC. The callback functions define init() to initialize the controller and wait() to wait until initialization is completed. Rename uniphier_pcie_init_ep() to uniphier_pcie_pro5_init_ep() for initializing PCIe controller implemented in Pro5 SoC. And Pro5 SoC doesn't have wait() function. Link: https://lore.kernel.org/r/1644480596-20037-3-git-send-email-hayashi.kunihiko@socionext.com Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Rob Herring <robh@kernel.org>
2022-02-08PCI: aardvark: Update comment about link going down after link-upMarek Behún
Update the comment about what happens when link goes down after we have checked for link-up. If a PIO request is done while link-down, we have a serious problem. Link: https://lore.kernel.org/r/20220110015018.26359-23-kabel@kernel.org Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Drop __maybe_unused from advk_pcie_disable_phy()Marek Behún
This function is now always used in driver remove method, drop the __maybe_unused attribute. Link: https://lore.kernel.org/r/20220110015018.26359-22-kabel@kernel.org Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Don't mask irq when mappingPali Rohár
By default, all Legacy INTx interrupts are masked, so there is no need to mask this interrupt during irq_map() callback. Link: https://lore.kernel.org/r/20220110015018.26359-21-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Remove irq_mask_ack() callback for INTx interruptsPali Rohár
Callback for irq_mask_ack() is the same as for irq_mask(). As there is no special handling for irq_ack(), there is no need to define irq_mask_ack() too. Link: https://lore.kernel.org/r/20220110015018.26359-20-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Marc Zyngier <maz@kernel.org>
2022-02-08PCI: aardvark: Use separate INTA interrupt for emulated root bridgePali Rohár
Emulated root bridge currently provides only one Legacy INTA interrupt which is used for reporting PCIe PME and ERR events and handled by kernel PCIe PME and AER drivers. Aardvark HW reports these PME and ERR events separately, so there is no need to mix real INTA interrupt and emulated INTA interrupt for PCIe PME and AER drivers. Register a new advk-RP (as in Root Port) irq chip and a new irq domain for emulated root bridge and use this new separate irq domain for providing INTA interrupt from emulated root bridge for PME and ERR events. The real INTA interrupt from real devices is now separate. A custom map_irq callback function on PCI host bridge structure is used to allocate IRQ mapping for emulated root bridge from new irq domain. Original callback of_irq_parse_and_map_pci() is used for all other devices as before. Link: https://lore.kernel.org/r/20220110015018.26359-19-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Fix support for PME requester on emulated bridgePali Rohár
Enable aardvark PME interrupt unconditionally by unmasking it and read PME requester ID to emulated bridge config space immediately after receiving interrupt. PME requester ID is stored in the PCIE_MSG_LOG_REG register, which contains the last inbound message. So when new inbound message is received by HW (including non-PM), the content in PCIE_MSG_LOG_REG register is replaced by a new value. PCIe specification mandates that subsequent PMEs are kept pending until the PME Status Register bit is cleared by software by writing a 1b. Support for masking/unmasking PME interrupt on emulated bridge via PCI_EXP_RTCTL_PMEIE bit is now implemented only in emulated bridge config space, to ensure that we do not miss any aardvark PME interrupt. Reading of PCI_EXP_RTCAP and PCI_EXP_RTSTA registers is simplified as final value is now always stored into emulated bridge config space by the interrupt handler, so there is no need to implement support for these registers in read_pcie callback. Clearing of W1C bit PCI_EXP_RTSTA_PME is now also simplified as it is done by pci-bridge-emul.c code for emulated bridge config space. So there is no need to implement support for clearing this bit in write_pcie callback. Link: https://lore.kernel.org/r/20220110015018.26359-18-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Add support for PME interruptsPali Rohár
Currently enabling PCI_EXP_RTSTA_PME bit in PCI_EXP_RTCTL register does nothing. This is because PCIe PME driver expects to receive PCIe interrupt defined in PCI_EXP_FLAGS_IRQ register, but aardvark hardware does not trigger PCIe INTx/MSI interrupt for PME event, rather it triggers custom aardvark interrupt which this driver is not processing yet. Fix this issue by handling PME interrupt in advk_pcie_handle_int() and chaining it to PCIe interrupt 0 with generic_handle_domain_irq() (since aardvark sets PCI_EXP_FLAGS_IRQ to zero). With this change PCIe PME driver finally starts receiving PME interrupt. Link: https://lore.kernel.org/r/20220110015018.26359-17-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Optimize writing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME on ↵Pali Rohár
emulated bridge To optimize advk_pci_bridge_emul_pcie_conf_write() code, touch PCIE_ISR0_REG and PCIE_ISR0_MASK_REG registers only when it is really needed, when processing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME bits. Link: https://lore.kernel.org/r/20220110015018.26359-16-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Fix reading PCI_EXP_RTSTA_PME bit on emulated bridgePali Rohár
The emulated bridge returns incorrect value for PCI_EXP_RTSTA register during readout in advk_pci_bridge_emul_pcie_conf_read() function: the correct bit is BIT(16), but we are setting BIT(23), because the code does *value = (isr0 & PCIE_MSG_PM_PME_MASK) << 16 where PCIE_MSG_PM_PME_MASK is BIT(7). The code should probably have been something like *value = (!!(isr0 & PCIE_MSG_PM_PME_MASK)) << 16, but we are better of using an if() and using the proper macro for this bit. Link: https://lore.kernel.org/r/20220110015018.26359-15-kabel@kernel.org Fixes: 8a3ebd8de328 ("PCI: aardvark: Implement emulated root PCI bridge config space") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Add support for ERR interrupt on emulated bridgePali Rohár
ERR interrupt is triggered when corresponding bit is unmasked in both ISR0 and PCI_EXP_DEVCTL registers. Unmasking ERR bits in PCI_EXP_DEVCTL register is not enough. This means that currently the ERR interrupt is never triggered. Unmask ERR bits in ISR0 register at driver probe time. ERR interrupt is not triggered until ERR bits are unmasked also in PCI_EXP_DEVCTL register, which is done by AER driver. So it is safe to unconditionally unmask all ERR bits in aardvark probe. Aardvark HW sets PCI_ERR_ROOT_AER_IRQ to zero and when corresponding bits in ISR0 and PCI_EXP_DEVCTL are enabled, the HW triggers a generic interrupt on GIC. Chain this interrupt to PCIe interrupt 0 with generic_handle_domain_irq() to allow processing of ERR interrupts. Link: https://lore.kernel.org/r/20220110015018.26359-14-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Enable MSI-X supportPali Rohár
According to PCI 3.0 specification, sending both MSI and MSI-X interrupts is done by DWORD memory write operation to doorbell message address. The write operation for MSI has zero upper 16 bits and the MSI interrupt number in the lower 16 bits, while the write operation for MSI-X contains a 32-bit value from MSI-X table. Since the driver only uses interrupt numbers from range 0..31, the upper 16 bits of the DWORD memory write operation to doorbell message address are zero even for MSI-X interrupts. Thus we can enable MSI-X interrupts. Testing proves that kernel can correctly receive MSI-X interrupts from PCIe cards which supports both MSI and MSI-X interrupts. Link: https://lore.kernel.org/r/20220110015018.26359-13-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Fix setting MSI addressPali Rohár
MSI address for receiving MSI interrupts needs to be correctly set before enabling processing of MSI interrupts. Move code for setting PCIE_MSI_ADDR_LOW_REG and PCIE_MSI_ADDR_HIGH_REG from advk_pcie_init_msi_irq_domain() to advk_pcie_setup_hw(), before enabling PCIE_CORE_CTRL2_MSI_ENABLE. After this we can remove the now unused member msi_msg, which was used only for MSI doorbell address. MSI address can be any address which cannot be used to DMA to. So change it to the address of the main struct advk_pcie. Link: https://lore.kernel.org/r/20220110015018.26359-12-kabel@kernel.org Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org # f21a8b1b6837 ("PCI: aardvark: Move to MSI handling using generic MSI support")
2022-02-08PCI: aardvark: Add support for masking MSI interruptsPali Rohár
We should not unmask MSIs at setup, but only when kernel asks for them to be unmasked. At setup, mask all MSIs, and implement IRQ chip callbacks for masking and unmasking particular MSIs. Link: https://lore.kernel.org/r/20220110015018.26359-11-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Refactor unmasking summary MSI interruptPali Rohár
Refactor the masking of ISR0/1 Sources and unmasking of summary MSI interrupt so that it corresponds to the comments: - first mask all ISR0/1 - then unmask all MSIs - then unmask summary MSI interrupt Link: https://lore.kernel.org/r/20220110015018.26359-10-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Use dev_fwnode() instead of of_node_to_fwnode(dev->of_node)Marek Behún
Use simple dev_fwnode(dev) instead of struct device_node *node = dev->of_node; of_node_to_fwnode(node) especially since the node variable is not used elsewhere in the function. Link: https://lore.kernel.org/r/20220110015018.26359-9-kabel@kernel.org Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Make msi_domain_info structure a static driver structureMarek Behún
Make Aardvark's msi_domain_info structure into a private driver structure. Domain info is same for every potential instatination of a controller. Link: https://lore.kernel.org/r/20220110015018.26359-8-kabel@kernel.org Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Make MSI irq_chip structures static driver structuresMarek Behún
In [1] it was agreed that we should use struct irq_chip as a global static struct in the driver. Even though the structure currently contains a dynamic member (parent_device), In [2] the plans to kill it and make the structure completely static were set out. Convert Aardvark's priv->msi_bottom_irq_chip and priv->msi_irq_chip to static driver structure. [1] https://lore.kernel.org/linux-pci/877dbcvngf.wl-maz@kernel.org/ [2] https://lore.kernel.org/linux-pci/874k6gvkhz.wl-maz@kernel.org/ Link: https://lore.kernel.org/r/20220110015018.26359-7-kabel@kernel.org Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Check return value of generic_handle_domain_irq() when ↵Pali Rohár
processing INTx IRQ It is possible that we receive spurious INTx interrupt. Check for the return value of generic_handle_domain_irq() when processing INTx IRQ. Link: https://lore.kernel.org/r/20220110015018.26359-6-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Rewrite IRQ code to chained IRQ handlerPali Rohár
Rewrite the code to use irq_set_chained_handler_and_data() handler with chained_irq_enter() and chained_irq_exit() processing instead of using devm_request_irq(). advk_pcie_irq_handler() reads IRQ status bits and calls other functions based on which bits are set. These functions then read its own IRQ status bits and calls other aardvark functions based on these bits. Finally generic_handle_domain_irq() with translated linux IRQ numbers are called. Link: https://lore.kernel.org/r/20220110015018.26359-5-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Fix support for MSI interruptsPali Rohár
Aardvark hardware supports Multi-MSI and MSI_FLAG_MULTI_PCI_MSI is already set for the MSI chip. But when allocating MSI interrupt numbers for Multi-MSI, the numbers need to be properly aligned, otherwise endpoint devices send MSI interrupt with incorrect numbers. Fix this issue by using function bitmap_find_free_region() instead of bitmap_find_next_zero_area(). To ensure that aligned MSI interrupt numbers are used by endpoint devices, we cannot use Linux virtual irq numbers (as they are random and not properly aligned). Instead we need to use the aligned hwirq numbers. This change fixes receiving MSI interrupts on Armada 3720 boards and allows using NVMe disks which use Multi-MSI feature with 3 interrupts. Without this NVMe disks freeze booting as linux nvme-core.c is waiting 60s for an interrupt. Link: https://lore.kernel.org/r/20220110015018.26359-4-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Fix reading MSI interrupt numberPali Rohár
In advk_pcie_handle_msi() it is expected that when bit i in the W1C register PCIE_MSI_STATUS_REG is cleared, the PCIE_MSI_PAYLOAD_REG is updated to contain the MSI number corresponding to index i. Experiments show that this is not so, and instead PCIE_MSI_PAYLOAD_REG always contains the number of the last received MSI, overall. Do not read PCIE_MSI_PAYLOAD_REG register for determining MSI interrupt number. Since Aardvark already forbids more than 32 interrupts and uses own allocated hwirq numbers, the msi_idx already corresponds to the received MSI number. Link: https://lore.kernel.org/r/20220110015018.26359-3-kabel@kernel.org Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2022-02-08PCI: aardvark: Replace custom PCIE_CORE_INT_* macros with PCI_INTERRUPT_*Pali Rohár
Header file linux/pci.h defines enum pci_interrupt_pin with corresponding PCI_INTERRUPT_* values. Link: https://lore.kernel.org/r/20220110015018.26359-2-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
2022-02-04Merge tag 'pci-v5.17-fixes-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull pci fixes from Bjorn Helgaas: - Restructure j721e_pcie_probe() so we don't dereference a NULL pointer (Bjorn Helgaas) - Add a kirin_pcie_data struct to identify different Kirin variants to fix probe failure for controllers with an internal PHY (Bjorn Helgaas) * tag 'pci-v5.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: kirin: Add dev struct for of_device_get_match_data() PCI: j721e: Initialize pcie->cdns_pcie before using it
2022-02-04PCI: kirin: Add dev struct for of_device_get_match_data()Bjorn Helgaas
Bean reported that a622435fbe1a ("PCI: kirin: Prefer of_device_get_match_data()") broke kirin_pcie_probe() because it assumed match data of 0 was a failure when in fact, it meant the match data was "(void *)PCIE_KIRIN_INTERNAL_PHY". Therefore, probing of "hisilicon,kirin960-pcie" devices failed with -EINVAL and an "OF data missing" message. Add a struct kirin_pcie_data to encode the PHY type. Then the result of of_device_get_match_data() should always be a non-NULL pointer to a struct kirin_pcie_data that contains the PHY type. Fixes: a622435fbe1a ("PCI: kirin: Prefer of_device_get_match_data()") Link: https://lore.kernel.org/r/20220202162659.GA12603@bhelgaas Link: https://lore.kernel.org/r/20220201215941.1203155-1-huobean@gmail.com Reported-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-02-03PCI: imx6: Allow to probe when dw_pcie_wait_for_link() failsFabio Estevam
The intention of commit 886a9c134755 ("PCI: dwc: Move link handling into common code") was to standardize the behavior of link down as explained in its commit log: "The behavior for a link down was inconsistent as some drivers would fail probe in that case while others succeed. Let's standardize this to succeed as there are usecases where devices (and the link) appear later even without hotplug. For example, a reconfigured FPGA device." The pci-imx6 still fails to probe when the link is not present, which causes the following warning: imx6q-pcie 8ffc000.pcie: Phy link never came up imx6q-pcie: probe of 8ffc000.pcie failed with error -110 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 30 at drivers/regulator/core.c:2257 _regulator_put.part.0+0x1b8/0x1dc Modules linked in: CPU: 0 PID: 30 Comm: kworker/u2:2 Not tainted 5.15.0-next-20211103 #1 Hardware name: Freescale i.MX6 SoloX (Device Tree) Workqueue: events_unbound async_run_entry_fn [<c0111730>] (unwind_backtrace) from [<c010bb74>] (show_stack+0x10/0x14) [<c010bb74>] (show_stack) from [<c0f90290>] (dump_stack_lvl+0x58/0x70) [<c0f90290>] (dump_stack_lvl) from [<c012631c>] (__warn+0xd4/0x154) [<c012631c>] (__warn) from [<c0f87b00>] (warn_slowpath_fmt+0x74/0xa8) [<c0f87b00>] (warn_slowpath_fmt) from [<c076b4bc>] (_regulator_put.part.0+0x1b8/0x1dc) [<c076b4bc>] (_regulator_put.part.0) from [<c076b574>] (regulator_put+0x2c/0x3c) [<c076b574>] (regulator_put) from [<c08c3740>] (release_nodes+0x50/0x178) Fix this problem by ignoring the dw_pcie_wait_for_link() error like it is done on the other dwc drivers. Tested on imx6sx-sdb and imx6q-sabresd boards. Link: https://lore.kernel.org/r/20220106103645.2790803-1-festevam@gmail.com Fixes: 886a9c134755 ("PCI: dwc: Move link handling into common code") Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com> Cc: <stable@vger.kernel.org>
2022-02-03PCI: hv: Fix NUMA node assignment when kernel boots with custom NUMA topologyLong Li
When kernel boots with a NUMA topology with some NUMA nodes offline, the PCI driver should only set an online NUMA node on the device. This can happen during KDUMP where some NUMA nodes are not made online by the KDUMP kernel. This patch also fixes the case where kernel is booting with "numa=off". Fixes: 999dd956d838 ("PCI: hv: Add support for protocol 1.3 and support PCI_BUS_RELATIONS2") Signed-off-by: Long Li <longli@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Tested-by: Purna Pavan Chandra Aekkaladevi <paekkaladevi@microsoft.com> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Link: https://lore.kernel.org/r/1643247814-15184-1-git-send-email-longli@linuxonhyperv.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
generated by cgit (git 2.34.1) at 2025-07-15 17:33:02 +0000