| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fixes from Krzysztof Wilczyński:
"Two small patches that are important for fixing boot time hang on
Intel JHL7540 'Titan Ridge' platforms equipped with a Thunderbolt
controller.
The boot time issue manifests itself when a PCI Express bandwidth
control is unnecessarily enabled on the Thunderbolt controller
downstream ports, which only supports a link speed of 2.5 GT/s in
accordance with USB4 v2 specification (p. 671, sec. 11.2.1, "PCIe
Physical Layer Logical Sub-block").
As such, there is no need to enable bandwidth control on such
downstream port links, which also works around the issue.
Both patches were tested by the original reporter on the hardware on
which the failure origin golly manifested itself. Both fixes were
proven to resolve the reported boot hang issue, and both patches have
been in linux-next this week with no reported problems"
* tag 'pci-v6.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/bwctrl: Enable only if more than one speed is supported
PCI: Honor Max Link Speed when determining supported speeds
|
|
If a PCIe port only supports a single speed, enabling bandwidth control
is pointless: There's no need to monitor autonomous speed changes, nor
can the speed be changed.
Not enabling it saves a small amount of memory and compute resources,
but also fixes a boot hang reported by Niklas: It occurs when enabling
bandwidth control on Downstream Ports of Intel JHL7540 "Titan Ridge 2018"
Thunderbolt controllers. The ports only support 2.5 GT/s in accordance
with USB4 v2 sec 11.2.1, so the present commit works around the issue.
PCIe r6.2 sec 8.2.1 prescribes that:
"A device must support 2.5 GT/s and is not permitted to skip support
for any data rates between 2.5 GT/s and the highest supported rate."
Consequently, bandwidth control is currently only disabled if a port
doesn't support higher speeds than 2.5 GT/s. However the Implementation
Note in PCIe r6.2 sec 7.5.3.18 cautions:
"It is strongly encouraged that software primarily utilize the
Supported Link Speeds Vector instead of the Max Link Speed field,
so that software can determine the exact set of supported speeds on
current and future hardware. This can avoid software being confused
if a future specification defines Links that do not require support
for all slower speeds."
In other words, future revisions of the PCIe Base Spec may allow gaps
in the Supported Link Speeds Vector. To be future-proof, don't just
check whether speeds above 2.5 GT/s are supported, but rather check
whether *more than one* speed is supported.
Fixes: 665745f27487 ("PCI/bwctrl: Re-add BW notification portdrv as PCIe BW controller")
Closes: https://lore.kernel.org/r/db8e457fcd155436449b035e8791a8241b0df400.camel@kernel.org
Link: https://lore.kernel.org/r/3564908a9c99fc0d2a292473af7a94ebfc8f5820.1734428762.git.lukas@wunner.de
Reported-by: Niklas Schnelle <niks@kernel.org>
Tested-by: Niklas Schnelle <niks@kernel.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Jonathan Cameron <Jonthan.Cameron@huawei.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The Supported Link Speeds Vector in the Link Capabilities 2 Register
indicates the *supported* link speeds. The Max Link Speed field in the
Link Capabilities Register indicates the *maximum* of those speeds.
pcie_get_supported_speeds() neglects to honor the Max Link Speed field and
will thus incorrectly deem higher speeds as supported. Fix it.
One user-visible issue addressed here is an incorrect value in the sysfs
attribute "max_link_speed".
But the main motivation is a boot hang reported by Niklas: Intel JHL7540
"Titan Ridge 2018" Thunderbolt controllers supports 2.5-8 GT/s speeds,
but indicate 2.5 GT/s as maximum. Ilpo recalls seeing this on more
devices. It can be explained by the controller's Downstream Ports
supporting 8 GT/s if an Endpoint is attached, but limiting to 2.5 GT/s
if the port interfaces to a PCIe Adapter, in accordance with USB4 v2
sec 11.2.1:
"This section defines the functionality of an Internal PCIe Port that
interfaces to a PCIe Adapter. [...]
The Logical sub-block shall update the PCIe configuration registers
with the following characteristics: [...]
Max Link Speed field in the Link Capabilities Register set to 0001b
(data rate of 2.5 GT/s only).
Note: These settings do not represent actual throughput. Throughput
is implementation specific and based on the USB4 Fabric performance."
The present commit is not sufficient on its own to fix Niklas' boot hang,
but it is a prerequisite: A subsequent commit will fix the boot hang by
enabling bandwidth control only if more than one speed is supported.
The GENMASK() macro used herein specifies 0 as lowest bit, even though
the Supported Link Speeds Vector ends at bit 1. This is done on purpose
to avoid a GENMASK(0, 1) macro if Max Link Speed is zero. That macro
would be invalid as the lowest bit is greater than the highest bit.
Ilpo has witnessed a zero Max Link Speed on Root Complex Integrated
Endpoints in particular, so it does occur in practice. (The Link
Capabilities Register is optional on RCiEPs per PCIe r6.2 sec 7.5.3.)
Fixes: d2bd39c0456b ("PCI: Store all PCIe Supported Link Speeds")
Closes: https://lore.kernel.org/r/70829798889c6d779ca0f6cd3260a765780d1369.camel@kernel.org
Link: https://lore.kernel.org/r/fe03941e3e1cc42fb9bf4395e302bff53ee2198b.1734428762.git.lukas@wunner.de
Reported-by: Niklas Schnelle <niks@kernel.org>
Tested-by: Niklas Schnelle <niks@kernel.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add support for the Xilinx Versal CPM5 Root Port Controller 1. The key
difference between Controller 0 and Controller 1 lies in the
platform-specific error interrupt bits, which are located at different
register offsets.
To handle these differences, updated variant structure to hold the
following platform-specific details:
- Interrupt status register offset (ir_status)
- Interrupt enable register offset (ir_enable)
- Miscellaneous interrupt values (ir_misc_value)
The driver differentiates between Controller 0 and Controller 1 using the
compatible string in the device tree. This ensures that the appropriate
register offsets are used for each controller, allowing for correct
handling of platform-specific interrupts and initialization.
Link: https://lore.kernel.org/r/20240922061318.2653503-3-thippesw@amd.com
Signed-off-by: Thippeswamy Havalige <thippesw@amd.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
When allocating a BAR using pci_epf_alloc_space(), there are checks that
round up the size to a power of two.
However, there is no check in pci_epc_set_bar() which verifies that the
requested BAR size is a power of two.
Add a power of two check in pci_epc_set_bar(), so that we don't need to
add such a check in each and every PCI endpoint controller driver.
Link: https://lore.kernel.org/r/20241213143301.4158431-14-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
A BAR of type BAR_FIXED has a fixed BAR size (the size cannot be changed).
When using pci_epf_alloc_space() to allocate backing memory for a BAR,
pci_epf_alloc_space() will always set the size to the fixed BAR size if
the BAR type is BAR_FIXED (and will give an error if you the requested size
is larger than the fixed BAR size).
However, some drivers might not call pci_epf_alloc_space() before calling
pci_epc_set_bar(), so add a check in pci_epc_set_bar() to ensure that an
EPF driver cannot set a size different from the fixed BAR size, if the BAR
type is BAR_FIXED.
The pci_epc_function_is_valid() check is removed because this check is now
done by pci_epc_get_features().
Link: https://lore.kernel.org/r/20241213143301.4158431-13-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
All non-DWC EPC drivers implement (struct pci_epc *)->ops->get_features().
All DWC EPC drivers implement (struct dw_pcie_ep *)->ops->get_features(),
except for pcie-artpec6.c.
epc_features has been required in pci-epf-test.c since commit 6613bc2301ba
("PCI: endpoint: Fix NULL pointer dereference for ->get_features()").
A follow-up commit will make further use of epc_features in EPC core code.
Implement epc_features in the only EPC driver where it is currently not
implemented.
Link: https://lore.kernel.org/r/20241213143301.4158431-12-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
|
|
dw_pcie_prog_ep_inbound_atu()
dw_pcie_prog_ep_inbound_atu() is used to program an inbound iATU in
"BAR Match Mode".
A memory address returned by e.g. kmalloc() is guaranteed to have natural
alignment (aligned to the size of the allocation). It is however not
guaranteed that pci_epc_set_bar() (and thus dw_pcie_prog_ep_inbound_atu())
is supplied an address that has natural alignment. (An EPF driver can send
in an arbitrary physical address to pci_epc_set_bar().)
The DWC Databook description for the LWR_TARGET_RW and LWR_TARGET_HW fields
in the IATU_LWR_TARGET_ADDR_OFF_INBOUND_i registers state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
Add a check to ensure that the physical address programmed in the iATU is
aligned to the size of the BAR (BAR_MASK+1), as without this, we can get
hard to debug errors, as we could write to bits that are read-only (without
getting a write error), which could cause the iATU to end up redirecting to
a physical address that is different from the address that we intended.
Link: https://lore.kernel.org/r/20241213143301.4158431-11-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
In commit 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update
inbound map address") set_bar() was modified to support dynamically
changing the backing physical address of a BAR that was already configured.
This means that set_bar() can be called twice, without ever calling
clear_bar() (as calling clear_bar() would clear the BAR's PCI address
assigned by the host).
This can only be done if the new BAR size/flags does not differ from the
existing BAR configuration. Add these missing checks.
If we allow set_bar() to set e.g. a new BAR size that differs from the
existing BAR size, the new address translation range will be smaller than
the BAR size already determined by the host, which would mean that a read
past the new BAR size would pass the iATU untranslated, which could allow
the host to read memory not belonging to the new struct pci_epf_bar.
While at it, add comments which clarifies the support for dynamically
changing the physical address of a BAR. (Which was also missing.)
Fixes: 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Link: https://lore.kernel.org/r/20241213143301.4158431-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
|
|
The "DesignWare Cores PCI Express Controller Register Descriptions,
Version 4.60a", section "1.21.70 IATU_LWR_TARGET_ADDR_OFF_INBOUND_i",
fields LWR_TARGET_RW and LWR_TARGET_HW both state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
If we do not write the BAR_MASK before writing the iATU registers, we are
relying the reset value of the BAR_MASK being larger than the requested
BAR size (which is supplied in the struct pci_epf_bar which is passed to
pci_epc_set_bar()). The reset value of the BAR_MASK is SoC dependent.
Thus, if the struct pci_epf_bar requests a BAR size that is larger than the
reset value of the BAR_MASK, the iATU will try to write to read-only bits,
which will cause the iATU to end up redirecting to a physical address that
is different from the address that was intended.
Thus, we should always write the iATU registers after writing the BAR_MASK.
Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20241213143301.4158431-9-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
|
|
Alexandre observed a warning emitted from pci_msi_setup_msi_irqs() on a
RISCV platform which does not provide PCI/MSI support:
WARNING: CPU: 1 PID: 1 at drivers/pci/msi/msi.h:121 pci_msi_setup_msi_irqs+0x2c/0x32
__pci_enable_msix_range+0x30c/0x596
pci_msi_setup_msi_irqs+0x2c/0x32
pci_alloc_irq_vectors_affinity+0xb8/0xe2
RISCV uses hierarchical interrupt domains and correctly does not implement
the legacy fallback. The warning triggers from the legacy fallback stub.
That warning is bogus as the PCI/MSI layer knows whether a PCI/MSI parent
domain is associated with the device or not. There is a check for MSI-X,
which has a legacy assumption. But that legacy fallback assumption is only
valid when legacy support is enabled, but otherwise the check should simply
return -ENOTSUPP.
Loongarch tripped over the same problem and blindly enabled legacy support
without implementing the legacy fallbacks. There are weak implementations
which return an error, so the problem was papered over.
Correct pci_msi_domain_supports() to evaluate the legacy mode and add
the missing supported check into the MSI enable path to complete it.
Fixes: d2a463b29741 ("PCI/MSI: Reject multi-MSI early")
Reported-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/87ed2a8ow5.ffs@tglx
|
|
After 17423360a27a ("PCI/ASPM: Save L1 PM Substates Capability for
suspend/resume"), pci_save_aspm_l1ss_state(dev) saves the L1SS state for
"dev", and pci_restore_aspm_l1ss_state(dev) restores the state for both
"dev" and its parent.
The problem is that unless pci_save_state() has been used in some other
path and has already saved the parent L1SS state, we will restore junk to
the parent, which means the L1 Substates likely won't work correctly.
Save the L1SS config for both the device and its parent in
pci_save_aspm_l1ss_state(). When restoring, we need both because L1SS must
be enabled at the parent (the Downstream Port) before being enabled at the
child (the Upstream Port).
Link: https://lore.kernel.org/r/20241115072200.37509-3-jhp@endlessos.org
Fixes: 17423360a27a ("PCI/ASPM: Save L1 PM Substates Capability for suspend/resume")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218394
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
[bhelgaas: parallel save/restore structure, simplify commit log, patch at
https://lore.kernel.org/r/20241212230340.GA3267194@bhelgaas]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org> # Asus B1400CEAE
|
|
When removing a virtual Endpoint, pci_epf_remove_vepf() failed to clear
epf_vf->epf_pf, which caused a subsequent pci_epf_add_vepf() to incorrectly
return -EBUSY:
pci_epf_add_vepf(epf_pf, epf_vf) // add
pci_epf_remove_vepf(epf_pf, epf_vf) // remove
pci_epf_add_vepf(epf_pf, epf_vf) // add again, -EBUSY error
Fix by clearing epf_vf->epf_pf in pci_epf_remove_vepf().
Link: https://lore.kernel.org/r/20241210-pci-epc-core_fix-v3-3-4d86dd573e4b@quicinc.com
Fixes: 1cf362e907f3 ("PCI: endpoint: Add support to add virtual function in endpoint core")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
|
|
Simplify pci_epc_get() implementation by using class_find_device_by_name().
Link: https://lore.kernel.org/r/20241210-pci-epc-core_fix-v3-2-4d86dd573e4b@quicinc.com
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
The devm_pci_epc_destroy() comment says destroys the EPC device, but it
does not actually do that since devres_destroy() does not call
devm_pci_epc_release(), and it also can not fully undo what the API
devm_pci_epc_create() does, so it is faulty.
Fortunately, the faulty API has not been used by current kernel tree. Use
devres_release() instead of devres_destroy() so the EPC device will be
released.
Link: https://lore.kernel.org/r/20241210-pci-epc-core_fix-v3-1-4d86dd573e4b@quicinc.com
Fixes: 5e8cb4033807 ("PCI: endpoint: Add EP core layer to enable EP controller and EP functions")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Link: https://lore.kernel.org/r/20241202-sysfs-const-bin_attr-pci-v1-4-c32360f495a7@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
PCI region request functions have a @name parameter (sometimes called
"res_name"). It is used in a log message to inform drivers about request
collisions, e.g., when another driver has requested that region already.
This message is only useful when it contains the actual owner of the
region, i.e., which driver requested it. So far, a great many drivers
misuse the @name parameter and just pass pci_name(), which doesn't result
in useful debug information.
Rename "res_name" to "name".
Detail @name's purpose in the docstrings.
Link: https://lore.kernel.org/r/20241203100023.31152-2-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
[bhelgaas: tweak comment wording to include "driver"]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Link: https://lore.kernel.org/r/20241202-sysfs-const-bin_attr-pci-v1-3-c32360f495a7@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
|
|
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Link: https://lore.kernel.org/r/20241202-sysfs-const-bin_attr-pci-v1-2-c32360f495a7@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Link: https://lore.kernel.org/r/20241202-sysfs-const-bin_attr-pci-v1-1-c32360f495a7@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Clean up the existing export namespace code along the same lines of
commit 33def8498fdd ("treewide: Convert macro and uses of __section(foo)
to __section("foo")") and for the same reason, it is not desired for the
namespace argument to be a macro expansion itself.
Scripted using
git grep -l -e MODULE_IMPORT_NS -e EXPORT_SYMBOL_NS | while read file;
do
awk -i inplace '
/^#define EXPORT_SYMBOL_NS/ {
gsub(/__stringify\(ns\)/, "ns");
print;
next;
}
/^#define MODULE_IMPORT_NS/ {
gsub(/__stringify\(ns\)/, "ns");
print;
next;
}
/MODULE_IMPORT_NS/ {
$0 = gensub(/MODULE_IMPORT_NS\(([^)]*)\)/, "MODULE_IMPORT_NS(\"\\1\")", "g");
}
/EXPORT_SYMBOL_NS/ {
if ($0 ~ /(EXPORT_SYMBOL_NS[^(]*)\(([^,]+),/) {
if ($0 !~ /(EXPORT_SYMBOL_NS[^(]*)\(([^,]+), ([^)]+)\)/ &&
$0 !~ /(EXPORT_SYMBOL_NS[^(]*)\(\)/ &&
$0 !~ /^my/) {
getline line;
gsub(/[[:space:]]*\\$/, "");
gsub(/[[:space:]]/, "", line);
$0 = $0 " " line;
}
$0 = gensub(/(EXPORT_SYMBOL_NS[^(]*)\(([^,]+), ([^)]+)\)/,
"\\1(\\2, \"\\3\")", "g");
}
}
{ print }' $file;
done
Requested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://mail.google.com/mail/u/2/#inbox/FMfcgzQXKWgMmjdFwwdsfgxzKpVHWPlc
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fix from Bjorn Helgaas:
- When removing a PCI device, only look up and remove a platform device
if there is an associated device node for which there could be a
platform device, to fix a merge window regression (Brian Norris)
* tag 'pci-v6.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/pwrctrl: Unregister platform device only if one actually exists
|
|
If a PCI device has an associated device_node with power supplies,
pci_bus_add_device() creates platform devices for use by pwrctrl. When the
PCI device is removed, pci_stop_dev() uses of_find_device_by_node() to
locate the related platform device, then unregisters it.
But when we remove a PCI device with no associated device node,
dev_of_node(dev) is NULL, and of_find_device_by_node(NULL) returns the
first device with "dev->of_node == NULL". The result is that we (a)
mistakenly unregister a completely unrelated platform device, leading to
issues like the first trace below, and (b) dereference the NULL pointer
from dev_of_node() when clearing OF_POPULATED, as in the second trace.
Unregister a platform device only if there is one associated with this PCI
device. This resolves issues seen when doing:
# echo 1 > /sys/bus/pci/devices/.../remove
Sample issue from unregistering the wrong platform device:
WARNING: CPU: 0 PID: 5095 at drivers/regulator/core.c:5885 regulator_unregister+0x140/0x160
Call trace:
regulator_unregister+0x140/0x160
devm_rdev_release+0x1c/0x30
release_nodes+0x68/0x100
devres_release_all+0x98/0xf8
device_unbind_cleanup+0x20/0x70
device_release_driver_internal+0x1f4/0x240
device_release_driver+0x20/0x40
bus_remove_device+0xd8/0x170
device_del+0x154/0x380
device_unregister+0x28/0x88
of_device_unregister+0x1c/0x30
pci_stop_bus_device+0x154/0x1b0
pci_stop_and_remove_bus_device_locked+0x28/0x48
remove_store+0xa0/0xb8
dev_attr_store+0x20/0x40
sysfs_kf_write+0x4c/0x68
Later NULL pointer dereference for of_node_clear_flag(NULL, OF_POPULATED):
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000c0
Call trace:
pci_stop_bus_device+0x190/0x1b0
pci_stop_and_remove_bus_device_locked+0x28/0x48
remove_store+0xa0/0xb8
dev_attr_store+0x20/0x40
sysfs_kf_write+0x4c/0x68
Link: https://lore.kernel.org/r/20241126210443.4052876-1-briannorris@chromium.org
Fixes: 681725afb6b9 ("PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent")
Reported-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Closes: https://lore.kernel.org/r/1732890621-19656-1-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Brian Norris <briannorris@chromium.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the two simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups
that can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog"
* tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Fix a potential abuse of seq_printf() format string in drivers
cpu: Remove spurious NULL in attribute_group definition
s390/con3215: Remove spurious NULL in attribute_group definition
perf: arm-ni: Remove spurious NULL in attribute_group definition
driver core: Constify bin_attribute definitions
sysfs: attribute_group: allow registration of const bin_attribute
firmware_loader: Fix possible resource leak in fw_log_firmware_info()
drivers: core: fw_devlink: Fix excess parameter description in docstring
driver core: class: Correct WARN() message in APIs class_(for_each|find)_device()
cacheinfo: Use of_property_present() for non-boolean properties
cdx: Fix cdx_mmap_resource() after constifying attr in ->mmap()
drivers: core: fw_devlink: Make the error message a bit more useful
phy: tegra: xusb: Set fwnode for xusb port devices
drm: display: Set fwnode for aux bus devices
driver core: fw_devlink: Stop trying to optimize cycle detection logic
driver core: Constify attribute arguments of binary attributes
sysfs: bin_attribute: add const read/write callback variants
sysfs: implement all BIN_ATTR_* macros in terms of __BIN_ATTR()
sysfs: treewide: constify attribute callback of bin_attribute::llseek()
sysfs: treewide: constify attribute callback of bin_attribute::mmap()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Make pci_stop_dev() and pci_destroy_dev() safe so concurrent
callers can't stop a device multiple times, even as we migrate from
the global pci_rescan_remove_lock to finer-grained locking (Keith
Busch)
- Improve pci_walk_bus() implementation by making it recursive and
moving locking up to avoid need for a 'locked' parameter (Keith
Busch)
- Unexport pci_walk_bus_locked(), which is only used internally by
the PCI core (Keith Busch)
- Detect some Thunderbolt chips that are built-in and hence
'trustworthy' by a heuristic since the 'ExternalFacingPort' and
'usb4-host-interface' ACPI properties are not quite enough (Esther
Shimanovich)
Resource management:
- Use PCI bus addresses (not CPU addresses) in 'ranges' properties
when building dynamic DT nodes so systems where PCI and CPU
addresses differ work correctly (Andrea della Porta)
- Tidy resource sizing and assignment with helpers to reduce
redundancy (Ilpo Järvinen)
- Improve pdev_sort_resources() 'bogus alignment' warning to be more
specific (Ilpo Järvinen)
Driver binding:
- Convert driver .remove_new() callbacks to .remove() again to finish
the conversion from returning 'int' to being 'void' (Sergio
Paracuellos)
- Export pcim_request_all_regions(), a managed interface to request
all BARs (Philipp Stanner)
- Replace pcim_iomap_regions_request_all() with
pcim_request_all_regions(), and pcim_iomap_table()[n] with
pcim_iomap(n), in the following drivers: ahci, crypto qat, crypto
octeontx2, intel_th, iwlwifi, ntb idt, serial rp2, ALSA korg1212
(Philipp Stanner)
- Remove the now unused pcim_iomap_regions_request_all() (Philipp
Stanner)
- Export pcim_iounmap_region(), a managed interface to unmap and
release a PCI BAR (Philipp Stanner)
- Replace pcim_iomap_regions(mask) with pcim_iomap_region(n), and
pcim_iounmap_regions(mask) with pcim_iounmap_region(n), in the
following drivers: fpga dfl-pci, block mtip32xx, gpio-merrifield,
cavium (Philipp Stanner)
Error handling:
- Add sysfs 'reset_subordinate' to reset the entire hierarchy below a
bridge; previously Secondary Bus Reset could only be used when
there was a single device below a bridge (Keith Busch)
- Warn if we reset a running device where the driver didn't register
pci_error_handlers notification callbacks (Keith Busch)
ASPM:
- Disable ASPM L1 before touching L1 PM Substates to follow the spec
closer and avoid a CPU load timeout on some platforms (Ajay
Agarwal)
- Set devices below Intel VMD to D0 before enabling ASPM L1 Substates
as required per spec for all L1 Substates changes (Jian-Hong Pan)
Power management:
- Enable starfive controller runtime PM before probing host bridge
(Mayank Rana)
- Enable runtime power management for host bridges (Krishna chaitanya
chundru)
Power control:
- Use of_platform_device_create() instead of of_platform_populate()
to create pwrctl platform devices so we can control it based on the
child nodes (Manivannan Sadhasivam)
- Create pwrctrl platform devices only if there's a relevant power
supply property (Manivannan Sadhasivam)
- Add device link from the pwrctl supplier to the PCI dev to ensure
pwrctl drivers are probed before the PCI dev driver; this avoids a
race where pwrctl could change device power state while the PCI
driver was active (Manivannan Sadhasivam)
- Find pwrctl device for removal with of_find_device_by_node()
instead of searching all children of the parent (Manivannan
Sadhasivam)
- Rename 'pwrctl' to 'pwrctrl' to match new bandwidth controller
('bwctrl') and hotplug files (Bjorn Helgaas)
Bandwidth control:
- Add read/modify/write locking for Link Control 2, which is used to
manage Link speed (Ilpo Järvinen)
- Extract Link Bandwidth Management Status check into
pcie_lbms_seen(), where it can be shared between the bandwidth
controller and quirks that use it to help retrain failed links
(Ilpo Järvinen)
- Re-add Link Bandwidth notification support with updates to address
the reasons it was previously reverted (Alexandru Gagniuc, Ilpo
Järvinen)
- Add pcie_set_target_speed() and related functionality so drivers
can manage PCIe Link speed based on thermal or other constraints
(Ilpo Järvinen)
- Add a thermal cooling driver to throttle PCIe Links via the
existing thermal management framework (Ilpo Järvinen)
- Add a userspace selftest for the PCIe bandwidth controller (Ilpo
Järvinen)
PCI device hotplug:
- Add hotplug controller driver for Marvell OCTEON multi-function
device where function 0 has a management console interface to
enable/disable and provision various personalities for the other
functions (Shijith Thotton)
- Retain a reference to the pci_bus for the lifetime of a pci_slot to
avoid a use-after-free when the thunderbolt driver resets USB4 host
routers on boot, causing hotplug remove/add of downstream docks or
other devices (Lukas Wunner)
- Remove unused cpcihp struct cpci_hp_controller_ops.hardware_test
(Guilherme Giacomo Simoes)
- Remove unused cpqphp struct ctrl_dbg.ctrl (Christophe JAILLET)
- Use pci_bus_read_dev_vendor_id() instead of hand-coded presence
detection in cpqphp (Ilpo Järvinen)
- Simplify cpqphp enumeration, which is already simple-minded and
doesn't handle devices below hot-added bridges (Ilpo Järvinen)
Virtualization:
- Add ACS quirk for Wangxun FF5xxx NICs, which don't advertise an ACS
capability but do isolate functions as though PCI_ACS_RR and
PCI_ACS_CR were set, so the functions can be in independent IOMMU
groups (Mengyuan Lou)
TLP Processing Hints (TPH):
- Add and document TLP Processing Hints (TPH) support so drivers can
enable and disable TPH and the kernel can save/restore TPH
configuration (Wei Huang)
- Add TPH Steering Tag support so drivers can retrieve Steering Tag
values associated with specific CPUs via an ACPI _DSM to improve
performance by directing DMA writes closer to their consumers (Wei
Huang)
Data Object Exchange (DOE):
- Wait up to 1 second for DOE Busy bit to clear before writing a
request to the mailbox to avoid failures if the mailbox is still
busy from a previous transfer (Gregory Price)
Endpoint framework:
- Skip attempts to allocate from endpoint controller memory window if
the requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to
handle controller-specific size and alignment constraints, and add
test cases to the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can
observe DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas
Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent
(Niklas Cassel)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks
'mmio' DT property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid
use-after-free (Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when
removing the secondary controller associated with an NTB (Zijun Hu)
Cadence PCIe controller driver:
- Lower severity of 'phy-names' message (Bartosz Wawrzyniak)
Freescale i.MX6 PCIe controller driver:
- Fix suspend/resume support on i.MX6QDL, which has a hardware
erratum that prevents use of L2 (Stefan Eichenberger)
Intel VMD host bridge driver:
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 DT binding to require the exact number of
clocks for each SoC (Fei Shao)
- Add support for DT 'max-link-speed' and 'num-lanes' properties to
restrict the link speed and width (AngeloGioacchino Del Regno)
Microchip PolarFlare PCIe controller driver:
- Add DT and driver support for using either of the two PolarFire
Root Ports (Conor Dooley)
NVIDIA Tegra194 PCIe controller driver:
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
Qualcomm PCIe controller driver:
- Add qcom SAR2130P DT binding with an additional clock (Dmitry
Baryshkov)
- Enable MSI interrupts if 'global' IRQ is supported, since a
previous commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP
v5.80a and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the
qcom,pcie-sm8450.yaml DT binding to qcom,pcie-common.yaml, where it
can be used by other Qcom platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the
link comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned
to support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the
'iommu-map' DT property and doesn't need BDF-to-SID translation
(Qiang Yu)
Rockchip PCIe controller driver:
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint
.align value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead
of searching for it, and verify that the address was mapped (Damien
Le Moal)
- When mapping an endpoint window, verify that the address hasn't
been mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which
fixes intermittent page faults in memcpy_toio() and memcpy_fromio()
(Damien Le Moal)
- Rename rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources() for consistency with similar DT
interfaces (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and do
it only in the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and
controller configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it
(Damien Le Moal)
- Add a handler for PERST# signal so we can detect host-initiated
resets and start link training after PERST# is deasserted (Damien
Le Moal)
Synopsys DesignWare PCIe controller driver:
- Clear outbound address on unmap so dw_pcie_find_index() won't match
an ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when
testing for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
TI J721E PCIe driver:
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100
us), before deasserting PERST# to ensure power and refclk are
stable (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root
Complex mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we
can do (Kishon Vijay Abraham I)
Miscellaneous:
- Reorganize kerneldoc parameter names to match order in function
signature (Julia Lawall)
- Fix sysfs reset_method_store() memory leak (Todd Kjos)
- Simplify pci_create_slot() (Ilpo Järvinen)
- Fix incorrect printf format specifiers in pcitest (Luo Yifan)"
* tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (127 commits)
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
PCI/pwrctrl: Rename pwrctrl functions and structures
PCI/pwrctrl: Rename pwrctl files to pwrctrl
PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent
PCI/pwrctl: Ensure that pwrctl drivers are probed before PCI client drivers
PCI/pwrctl: Create pwrctl device only if at least one power supply is present
PCI/pwrctl: Use of_platform_device_create() to create pwrctl devices
tools: PCI: Fix incorrect printf format specifiers
...
|
|
- Fix typos and whitespace errors (Bjorn Helgaas)
* pci/typos:
PCI: Fix typos
|
|
- Reorganize kerneldoc parameter names to match order in function signature
(Julia Lawall)
- Remove kerneldoc return value descriptions from hotplug registration
interfaces that don't return anything (Ilpo Järvinen)
- Fix sysfs reset_method_store() memory leak (Todd Kjos)
- Simplify pci_create_slot() (Ilpo Järvinen)
- Fix incorrect printf format specifiers in pcitest (Luo Yifan)
* pci/misc:
tools: PCI: Fix incorrect printf format specifiers
PCI: Simplify pci_create_slot() logic
PCI: Fix reset_method_store() memory leak
PCI: hotplug: Remove "Returns" kerneldoc from void functions
PCI: hotplug: Reorganize kerneldoc parameter names
|
|
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
* pci/controller/vmd:
PCI: vmd: Add DID 8086:B06F and 8086:B60B for Intel client SKUs
|
|
- Move endpoint controller cleanups that depend on refclk from the host to
the notifier that tells us the host has deasserted PERST# (Manivannan
Sadhasivam)
* pci/controller/tegra194:
PCI: tegra194: Move controller cleanups to pex_ep_event_pex_rst_deassert()
|
|
- Fix address translation unit programming (Damien Le Moal)
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint .align
value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead of
searching for it, and verify that the address was mapped (Damien Le Moal)
- When mapping an endpoint window, verify that the address hasn't been
mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which fixes
intermittent page faults in memcpy_toio() and memcpy_fromio() (Damien Le
Moal)
- Rename rockchip_pcie_parse_ep_dt() to rockchip_pcie_ep_get_resources()
for consistency with similar DT interfaces (Damien Le Moal)
- Factor out memory allocations to tidy rockchip_pcie_ep_probe() (Damien Le
Moal)
- Factor out MSI-X quirk to tidy rockchip_pcie_ep_probe() (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and only in
the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and controller
configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it (Damien Le
Moal)
- Add a handler for PERST# signal so we can detect host resets and start
link training when exiting reset (Damien Le Moal)
* pci/controller/rockchip:
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
|
|
- Enable MSI interrupts if 'global' IRQ is supported, since a previous
commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the host to
the notifier that tells us the host has deasserted PERST# (Manivannan
Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP v5.80a
and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the qcom,pcie-sm8450.yaml
DT binding to qcom,pcie-common.yaml, where it can be used by other Qcom
platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the link
comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned to
support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the 'iommu-map'
DT property and doesn't need BDF-to-SID translation (Qiang Yu)
* pci/controller/qcom:
PCI: qcom: Disable ASPM L0s for X1E80100
PCI: qcom: Remove BDF2SID mapping config for SC8280X family SoC
dt-bindings: PCI: qcom,pcie-x1e80100: Add 'global' interrupt
dt-bindings: PCI: qcom: Move OPP table to qcom,pcie-common.yaml
PCI: qcom: Add support for IPQ9574
dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller
PCI: qcom-ep: Move controller cleanups to qcom_pcie_perst_deassert()
PCI: qcom: Enable MSI interrupts together with Link up if 'Global IRQ' is supported
|
|
- Add DT and driver support for using either of the two PolarFire Root
Ports (Conor Dooley)
* pci/controller/microchip:
PCI: microchip: Add support for using either Root Port 1 or 2
dt-bindings: PCI: microchip,pcie-host: Add reg for Root Port 2
|
|
- Add support for DT 'max-link-speed' and 'num-lanes' properties to
restrict the link speed and width (AngeloGioacchino Del Regno)
* pci/controller/mediatek:
PCI: mediatek-gen3: Remove unneeded semicolon
PCI: mediatek-gen3: Add support for restricting link width
PCI: mediatek-gen3: Add support for setting max-link-speed limit
|
|
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root Complex
mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we can do
(Kishon Vijay Abraham I)
* pci/controller/keystone:
PCI: keystone: Add link up check to ks_pcie_other_map_bus()
PCI: keystone: Set mode as Root Complex for "ti,keystone-pcie" compatible
|
|
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100 us),
before deasserting PERST# to ensure power and refclk are stable
(Siddharth Vadapalli)
* pci/controller/j721e:
PCI: j721e: Deassert PERST# after a delay of PCIE_T_PVPERL_MS milliseconds
PCI: j721e: Add PCIe support for J722S SoC
|
|
- Fix suspend/resume support on i.MX6QDL, which has a hardware erratum that
prevents use of L2 (Stefan Eichenberger)
* pci/controller/imx6:
PCI: imx6: Fix suspend/resume support on i.MX6QDL
|
|
- Clear outbound address on unmap so dw_pcie_find_index() won't match an
ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when testing
for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
* pci/controller/dwc:
PCI: dwc: ep: Fix advertised resizable BAR size regression
PCI: dwc: Use of_property_present() for non-boolean properties
PCI: dwc: endpoint: Clear outbound address on unmap
|
|
- Lower severity of 'phy-names' message (Bartosz Wawrzyniak)
* pci/controller/cadence:
PCI: cadence: Lower severity of message when phy-names property is absent in DTS
|
|
- Add pci_epc_function_is_valid() to avoid repeating common validation
checks (Damien Le Moal)
- Skip attempts to allocate from endpoint controller memory window if the
requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to handle
controller-specific size and alignment constraints, and add test cases to
the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can observe
DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent (Niklas
Cassel)
- Remove superfluous 'return' from pci_epf_test_clean_dma_chan() (Wang
Jiang)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks 'mmio' DT
property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid use-after-free
(Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when removing
the secondary controller associated with an NTB (Zijun Hu)
- Fix pci_epc_map map_size kerneldoc (Rick Wertenbroek)
* pci/endpoint:
PCI: endpoint: Fix pci_epc_map map_size kerneldoc string
PCI: endpoint: Clear secondary (not primary) EPC in pci_epc_remove_epf()
PCI: endpoint: Fix PCI domain ID release in pci_epc_destroy()
PCI: endpoint: epf-mhi: Avoid NULL dereference if DT lacks 'mmio'
PCI: endpoint: Remove surplus return statement from pci_epf_test_clean_dma_chan()
PCI: dwc: ep: Use align addr function for dw_pcie_ep_raise_{msi,msix}_irq()
PCI: endpoint: test: Synchronously cancel command handler work
PCI: dwc: endpoint: Implement the pci_epc_ops::align_addr() operation
PCI: endpoint: test: Use pci_epc_mem_map/unmap()
PCI: endpoint: Update documentation
PCI: endpoint: Introduce pci_epc_mem_map()/unmap()
PCI: endpoint: Improve pci_epc_mem_alloc_addr()
PCI: endpoint: Introduce pci_epc_function_is_valid()
|
|
- Add ACS quirk for Wangxun FF5xxx NICs, which don't advertise and ACS
capability but do isolate functions as though PCI_ACS_RR and PCI_ACS_CR
were set, so the functions can be in independent IOMMU groups (Mengyuan
Lou)
* pci/virtualization:
PCI: Add ACS quirk for Wangxun FF5xxx NICs
|
|
- Add and document TLP Processing Hints (TPH) support so drivers can enable
and disable TPH and the kernel can save/restore TPH configuration (Wei
Huang)
- Add TPH Steering Tag support so drivers can retrieve Steering Tag values
associated with specific CPUs via an ACPI _DSM to direct DMA writes
closer to their consumers (Wei Huang)
* pci/tph:
PCI/TPH: Add TPH documentation
PCI/TPH: Add Steering Tag support
PCI: Add TLP Processing Hints (TPH) support
|
|
- Detect some Thunderbolt chips that are built-in and hence 'trustworthy'
by a heuristic since the 'ExternalFacingPort' and 'usb4-host-interface'
ACPI properties are not quite enough (Esther Shimanovich)
* pci/thunderbolt:
PCI: Detect and trust built-in Thunderbolt chips
|
|
- Add resource_set_size() to set resource size when start has already been
set (Ilpo Järvinen)
- Add resource_set_range() helper to set both resource start and size (Ilpo
Järvinen)
- Use IS_ALIGNED() and resource_size() in quirk_s3_64M() instead of
open-coding them (Ilpo Järvinen)
- Add ALIGN_DOWN_IF_NONZERO() to avoid code duplication when distributing
resources across devices (Ilpo Järvinen)
- Improve pdev_sort_resources() warning message to be more specific (Ilpo
Järvinen)
* pci/resource:
PCI: Improve pdev_sort_resources() warning message
PCI: Add ALIGN_DOWN_IF_NONZERO() helper
PCI: Use align and resource helpers, and SZ_* in quirk_s3_64M()
PCI: Use resource_set_{range,size}() helpers
resource: Add resource set range and size helpers
|
|
- Add sysfs 'reset_subordinate' to reset hierarchy below bridge (Keith
Busch)
- Warn if we reset a running device where driver didn't register
pci_error_handlers notification callbacks (Keith Busch)
* pci/reset:
PCI: Warn if a running device is unaware of reset
PCI: Add 'reset_subordinate' to reset hierarchy below bridge
|
|
- Use of_platform_device_create() instead of of_platform_populate() to
create pwrctl platform devices so we can control it based on the child
nodes (Manivannan Sadhasivam)
- Create pwrctrl platform devices only if there's a relevant power supply
property (Manivannan Sadhasivam)
- Add device link from the pwrctl supplier to the PCI dev to ensure pwrctl
drivers are probed before the PCI dev driver; this avoids a race where
pwrctl could change device power state while the PCI driver was active
(Manivannan Sadhasivam)
- Find pwrctl device for removal with of_find_device_by_node() instead of
searching all children of the parent (Manivannan Sadhasivam)
- Rename 'pwrctl' to 'pwrctrl' to use the same 'ctrl' suffix as 'bwctrl'
and other PCI files to reduce confusion (Bjorn Helgaas)
* pci/pwrctl:
PCI/pwrctrl: Rename pwrctrl functions and structures
PCI/pwrctrl: Rename pwrctl files to pwrctrl
PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent
PCI/pwrctl: Ensure that pwrctl drivers are probed before PCI client drivers
PCI/pwrctl: Create pwrctl device only if at least one power supply is present
PCI/pwrctl: Use of_platform_device_create() to create pwrctl devices
# Conflicts:
# drivers/pci/bus.c
# drivers/pci/remove.c
|
|
- Enable starfive controller runtime PM before probing host bridge (Mayank
Rana)
- Enable runtime power management for host bridges (Krishna chaitanya
chundru)
* pci/pm:
PCI: Enable runtime PM of the host bridge
PCI: starfive: Enable controller runtime PM before probing host bridge
|
|
- Use PCI bus addresses (not CPU addresses) in 'ranges' properties when
building dynamic DT nodes so systems where the PCI and CPU addresses
space differ work correctly (Andrea della Porta)
* pci/of:
PCI: of_property: Assign PCI instead of CPU bus address to dynamic PCI nodes
|
|
- Make pci_stop_dev() and pci_destroy_dev() concurrent safe (Keith Busch)
- Move __pci_walk_bus() mutex up into the caller, which avoids the need for
a parameter to control locking (Keith Busch)
- Simplify __pci_walk_bus() by making it recursive (Keith Busch)
- Unexport pci_walk_bus_locked(), which is only used internally by the PCI
core (Keith Busch)
* pci/locking:
PCI: Unexport pci_walk_bus_locked()
PCI: Convert __pci_walk_bus() to be recursive
PCI: Move __pci_walk_bus() mutex to where we need it
PCI: Make pci_destroy_dev() concurrent safe
PCI: Make pci_stop_dev() concurrent safe
|
|
- Add hotplug controller driver for Marvell OCTEON multi-function device
where function 0 has a management console interface to enable/disable and
provision various personalities for the other functions (Shijith Thotton)
* pci/hotplug-octeon:
PCI: hotplug: Add OCTEON PCI hotplug controller driver
|
|
- Remove unused cpcihp struct cpci_hp_controller_ops.hardware_test
(Guilherme Giacomo Simoes)
- Remove unused cpqphp struct ctrl_dbg.ctrl (Christophe JAILLET)
- Clean up cpqphp PCIBIOS_* return value confusion (Ilpo Järvinen)
- Use pci_bus_read_dev_vendor_id() instead of hand-coded presence detection
in cpqphp (Ilpo Järvinen)
- Simplify cpqphp enumeration, which is already simple-minded and doesn't
handle devices below hot-added bridges (Ilpo Järvinen)
- Retain a reference to the pci_bus for the lifetime of a pci_slot to avoid
a use-after-free when the thunderbolt driver resets USB4 host routers on
boot, causing hotplug remove/add of downstream docks or other devices
(Lukas Wunner)
* pci/hotplug:
PCI: Fix use-after-free of slot->bus on hot remove
PCI: cpqphp: Simplify PCI_ScanBusForNonBridge()
PCI: cpqphp: Use define to read class/revision dword
PCI: cpqphp: Use pci_bus_read_dev_vendor_id() to detect presence
PCI: cpqphp: Fix PCIBIOS_* return value confusion
PCI: cpqphp: Remove unused struct ctrl_dbg.ctrl
PCI: cpcihp: Remove unused struct cpci_hp_controller_ops.hardware_test
|
