| Age | Commit message (Collapse) | Author |
|---|
|
- Simplify pci_read_bridge_bases() logic (Ilpo Järvinen)
* pci/enumeration:
PCI: Simplify pci_read_bridge_bases() logic
PCI: Move struct pci_bus_resource into bus.c
PCI: Remove unused PCI_SUBTRACTIVE_DECODE
|
|
- Convert driver .remove_new() callbacks to .remove() again to finish the
conversion from returning 'int' to being 'void' (Sergio Paracuellos)
* pci/driver-remove:
PCI: acpiphp_ampere_altra: Switch back to struct platform_driver::remove()
PCI: controller: Switch back to struct platform_driver::remove()
|
|
- Export pcim_request_all_regions(), a managed interface to request all
BARs (Philipp Stanner)
- Replace pcim_iomap_regions_request_all() with pcim_request_all_regions(),
and pcim_iomap_table()[n] with pcim_iomap(n), in the following drivers:
ahci, crypto qat, crypto octeontx2, intel_th, iwlwifi, ntb idt, serial
rp2, ALSA korg1212 (Philipp Stanner)
- Remove the now unused pcim_iomap_regions_request_all() (Philipp Stanner)
- Export pcim_iounmap_region(), a managed interface to unmap and release a
PCI BAR (Philipp Stanner)
- Replace pcim_iomap_regions(mask) with pcim_iomap_region(n), and
pcim_iounmap_regions(mask) with pcim_iounmap_region(n), in the following
drivers: fpga dfl-pci, block mtip32xx, gpio-merrifield, cavium (Philipp
Stanner)
* pci/devm:
ethernet: cavium: Replace deprecated PCI functions
gpio: Replace deprecated PCI functions
fpga/dfl-pci.c: Replace deprecated PCI functions
PCI: Deprecate pcim_iounmap_regions()
PCI: Make pcim_iounmap_region() a public function
PCI: Remove pcim_iomap_regions_request_all()
ALSA: korg1212: Replace deprecated PCI functions
serial: rp2: Replace deprecated PCI functions
ntb: idt: Replace deprecated PCI functions
wifi: iwlwifi: replace deprecated PCI functions
intel_th: pci: Replace deprecated PCI functions
crypto: marvell - replace deprecated PCI functions
crypto: qat - replace deprecated PCI functions
ata: ahci: Replace deprecated PCI functions
PCI: Make pcim_request_all_regions() a public function
|
|
- Wait up to 1 second for DOE Busy bit to clear before writing a request to
the mailbox to avoid failures if the mailbox is still busy from a
previous transfer (Gregory Price)
* pci/doe:
PCI/DOE: Poll DOE Busy bit for up to 1 second in pci_doe_send_req()
|
|
- Add read/modify/write locking for Link Control 2, which is used to manage
Link speed (Ilpo Järvinen)
- Cache all supported Link speeds for use by the PCIe bandwidth controller
(Ilpo Järvinen)
- Extract the Link Bandwidth Management Status check into pcie_lbms_seen(),
where it can be shared between the bandwidth controller and quirks that
use it to help retrain failed links (Ilpo Järvinen)
- Re-add Link Bandwidth notification support with updates to address the
reasons it was previously reverted (Alexandru Gagniuc, Ilpo Järvinen)
- Add pcie_set_target_speed() and related functionality to manage PCIe Link
speed based on thermal constraints (Ilpo Järvinen)
- Add a thermal cooling driver to throttle PCIe Links via the existing
thermal management framework (Ilpo Järvinen)
- Add a userspace selftest for the PCIe bandwidth controller (Ilpo
Järvinen)
- Drop duplicate pcie_get_speed_cap(), pcie_get_width_cap() declarations
(Bjorn Helgaas)
* pci/bwctrl:
PCI: Drop duplicate pcie_get_speed_cap(), pcie_get_width_cap() declarations
selftests/pcie_bwctrl: Create selftests
thermal: Add PCIe cooling driver
PCI/bwctrl: Add pcie_set_target_speed() to set PCIe Link Speed
PCI/bwctrl: Re-add BW notification portdrv as PCIe BW controller
PCI: Abstract LBMS seen check into pcie_lbms_seen()
PCI: Refactor pcie_update_link_speed()
PCI: Store all PCIe Supported Link Speeds
PCI: Protect Link Control 2 Register with RMW locking
Documentation PCI: Reformat RMW ops documentation
|
|
Currently, the Rockchip PCIe endpoint controller driver does not handle
the PERST# signal, which prevents detecting when link training should
actually be started or if the host resets the device. This however can
be supported using the controller reset_gpios property set as an input
GPIO for endpoint mode.
Modify the Rockchip PCI endpoint controller driver to get the reset_gpio
and its associated interrupt which is serviced using a threaded IRQ with
the function rockchip_pcie_ep_perst_irq_thread() as handler.
This handler function notifies a link down event corresponding to the RC
side asserting the PERST# signal using pci_epc_linkdown() when the gpio
is high. Once the gpio value goes down, corresponding to the RC
de-asserting the PERST# signal, link training is started. The polarity
of the gpio interrupt trigger is changed from high to low after the RC
asserted PERST#, and conversely changed from low to high after the RC
de-asserts PERST#.
Also, given that the host mode controller and the endpoint mode
controller use two different property names for the same PERST# signal
(ep_gpios property and reset_gpios property respectively), for clarity,
rename the ep_gpio field of struct rockchip_pcie to perst_gpio.
Link: https://lore.kernel.org/r/20241017015849.190271-14-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: make log messages consistent, add missing include]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The Rockchip RK3399 TRM V1.3 Part2, Section 17.5.8.1.2, step 7,
describes the endpoint mode link training process clearly and states
that:
Insure link training completion and success by observing link_st field
in PCIe Client BASIC_STATUS1 register change to 2'b11. If both side
support PCIe Gen2 speed, re-train can be Initiated by asserting the
Retrain Link field in Link Control and Status Register. The software
should insure the BASIC_STATUS0[negotiated_speed] changes to "1", that
indicates re-train to Gen2 successfully.
This procedure is very similar to what is done for the root-port mode
in rockchip_pcie_host_init_port().
Implement this link training procedure for the endpoint mode as well.
Given that the RK3399 SoC does not have an interrupt signaling link
status changes, training is implemented as a delayed work which is
rescheduled until the link training completes or the endpoint controller
is stopped. The link training work is first scheduled in
rockchip_pcie_ep_start() when the endpoint function is started. Link
training completion is signaled to the function using pci_epc_linkup().
Accordingly, the linkup_notifier field of the Rockchip pci_epc_features
structure is changed to true.
Link: https://lore.kernel.org/r/20241017015849.190271-13-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: update log messages to make them consistent]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Define the EPC operation ->stop() for the Rockchip endpoint driver with
the function rockchip_pcie_ep_stop(). This function disables link
training and the controller configuration, as the reverse to what
the start operation defined with rockchip_pcie_ep_start() does.
Link: https://lore.kernel.org/r/20241017015849.190271-12-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The function rockchip_pcie_init_port() enables link training for a
controller configured in EP mode. Enabling link training is again done
in rockchip_pcie_ep_probe() after that function executed
rockchip_pcie_init_port(). Enabling link training only needs to be done
once, and doing so at the probe stage before the controller is actually
started by the user serves no purpose.
Refactor this by removing the link training enablement from both
rockchip_pcie_init_port() and rockchip_pcie_ep_probe() and moving it to
the endpoint start operation defined with rockchip_pcie_ep_start().
Enabling the controller configuration using the PCIE_CLIENT_CONF_ENABLE
bit in the same PCIE_CLIENT_CONFIG register is also moved to
rockchip_pcie_ep_start() and both the controller configuration and link
training enable bits are set with a single call to
rockchip_pcie_write().
Link: https://lore.kernel.org/r/20241017015849.190271-11-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move the code in rockchip_pcie_ep_probe() to hide the MSI-X capability
to its own function, rockchip_pcie_ep_hide_broken_msix_cap().
No functional changes.
Link: https://lore.kernel.org/r/20241017015849.190271-10-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Introduce the function rockchip_pcie_ep_init_ob_mem() allocate the
outbound memory regions and memory needed for IRQ handling.
These changes tidy up rockchip_pcie_ep_probe().
No functional change.
Link: https://lore.kernel.org/r/20241017015849.190271-9-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
To be consistent with the usual "get_resources" naming of driver
functions that acquire controller resources like clocks, PHY etc,
rename the function rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources().
No functional changes.
Link: https://lore.kernel.org/r/20241017015849.190271-8-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The call to rockchip_pcie_prog_ep_ob_atu() used to map the PCI address
of MSI data to the memory window allocated on probe for IRQs is done
in rockchip_pcie_ep_send_msi_irq() assuming a fixed alignment to a
256B boundary of the PCI address. This is not correct as the alignment
constraint for the RK3399 PCI mapping depends on the number of bits of
address changing in the mapped region. This leads to an unstable system
which sometimes work and sometimes does not (crashing on paging faults
when memcpy_toio() or memcpy_fromio() are used).
Similar to regular data mapping, the MSI data mapping must thus be
handled according to the information provided by
rockchip_pcie_ep_align_addr(). Modify rockchip_pcie_ep_send_msi_irq()
to use rockchip_pcie_ep_align_addr() to correctly program entry 0 of
the ATU for sending MSI IRQs.
Link: https://lore.kernel.org/r/20241017015849.190271-7-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits from the CPU address space used for the
mapping. For a PCI mapping of size bytes starting from pci_addr, the
number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1], up to 20 bits, that is,
up to 1MB mappings.
This means that when preparing a PCI address mapping, an endpoint
function driver must use an offset into the allocated controller
memory region that is equal to the mask of the starting PCI address
over rockchip_pcie_ep_ob_atu_num_bits() bits. This offset also
determines the maximum size of the mapping given the starting PCI
address and the fixed 1MB controller memory window size.
Implement the ->align_addr() endpoint controller operation to allow the
mapping alignment to be transparently handled by endpoint function
drivers through the function pci_epc_mem_map().
Link: https://lore.kernel.org/r/20241017015849.190271-6-dlemoal@kernel.org
Co-developed-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: change local variable name for address offset]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add a check to verify that the outbound region to be used for mapping an
address is not already in use.
Link: https://lore.kernel.org/r/20241017015849.190271-5-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
There is no need to loop over all regions to find the memory window used
to map an address. We can use rockchip_ob_region() to determine the
region index, together with a check that the address passed as argument
is the address used to create the mapping. Furthermore, the
ob_region_map bitmap should also be checked to ensure that we are not
attempting to unmap an address that is not mapped.
Link: https://lore.kernel.org/r/20241017015849.190271-4-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Introduce the macro ROCKCHIP_PCIE_AT_SIZE_ALIGN to initialize the .align
field of the controller epc_features structure to 256. This is defined
as a shift using the macro ROCKCHIP_PCIE_AT_MIN_NUM_BITS (to avoid
using the "magic" value 8 directly).
Link: https://lore.kernel.org/r/20241017015849.190271-3-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits masked from the CPU address space used for the
mapping. For a PCI mapping of <size> bytes starting from <pci_addr>,
the number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1].
However, rockchip_pcie_prog_ep_ob_atu() calculates num_pass_bits only
using the size of the mapping, resulting in an incorrect number of mask
bits depending on the value of the PCI address to map.
Fix this by introducing the helper function
rockchip_pcie_ep_ob_atu_num_bits() to correctly calculate the number of
mask bits to use to program the address translation unit. The number of
mask bits is calculated depending on both the PCI address and size of
the mapping, and clamped between 8 and 20 using the macros
ROCKCHIP_PCIE_AT_MIN_NUM_BITS and ROCKCHIP_PCIE_AT_MAX_NUM_BITS. As
defined in the Rockchip RK3399 TRM V1.3 Part2, Sections 17.5.5.1.1 and
17.6.8.2.1, this clamping is necessary because:
1) The lower 8 bits of the PCI address to be mapped by the outbound
region are ignored. So a minimum of 8 address bits are needed and
imply that the PCI address must be aligned to 256.
2) The outbound memory regions are 1MB in size. So while we can specify
up to 63-bits for the PCI address (num_bits filed uses bits 0 to 5 of
the outbound address region 0 register), we must limit the number of
valid address bits to 20 to match the memory window maximum size (1
<< 20 = 1MB).
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/r/20241017015849.190271-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
|
|
Rename pwrctrl functions and structures from "pwrctl" to "pwrctrl" to match
the similar file renames.
Link: https://lore.kernel.org/r/20241115214428.2061153-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
|
|
To slightly reduce confusion between "pwrctl" (the power controller and
power sequencing framework) and "bwctrl" (the bandwidth controller),
rename "pwrctl" to "pwrctrl" so they use the same "ctrl" suffix.
Rename drivers/pci/pwrctl/ to drivers/pci/pwrctrl/, including the related
MAINTAINERS, include file (include/linux/pci-pwrctl.h), Makefile, and
Kconfig changes.
This is the minimal rename of files only. A subsequent commit will rename
functions and data structures.
Link: https://lore.kernel.org/r/20241115214428.2061153-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
|
|
pwrctl parent
There is no need to iterate over all children of the pwrctl device parent
to remove the pwrctl device. Since the pwrctl device associated with the
PCI device can be found using of_find_device_by_node() API, use it directly
instead.
Any pwrctl devices lying around without getting associated with the PCI
devices will be removed once their parent device gets removed.
Link: https://lore.kernel.org/r/20241025-pci-pwrctl-rework-v2-5-568756156cbe@linaro.org
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
As per the kernel device driver model, a pwrctl device is the supplier for
the PCI device, but the device link that enforces the supplier-consumer
relationship was previously created by the pwrctl driver. Therefore, the
driver model didn't prevent probing PCI client drivers before probing the
corresponding pwrctl drivers. This may lead to a race condition if the PCI
device was already powered on by the bootloader (before the pwrctl driver).
If the bootloader did not power on the PCI device, this wouldn't create any
problem as the pwrctl driver will be the one powering on the device, so the
PCI client driver always gets probed afterward. But if the device was
already powered on, then the device will be seen by the PCI core and the
PCI client driver may get probed before its pwrctl driver. This creates a
race condition as the pwrctl driver may change the device power state while
the device is being accessed by the client driver.
One such issue was already reported on the Qcom X13s platform with the WLAN
device and fixed with a hack in the WCN pwrseq driver by a9aaf1ff88a8
("power: sequencing: request the WLAN enable GPIO as-is").
A cleaner way to fix the above mentioned race condition is to ensure that
the pwrctl drivers are always probed before the client drivers.
If the PCI device is associated with a pwrctl platform device with a power
supply, add a device link between the PCI device and the pwrctl device
before device_attach() in pci_bus_add_device().
Note that there is no need to explicitly remove the device link as that
will be taken care of by the driver core when the PCI device gets removed.
Fixes: 4565d2652a37 ("PCI/pwrctl: Add PCI power control core code")
Fixes: 8fb18619d910 ("PCI/pwrctl: Create platform devices for child OF nodes of the port node")
Link: https://lore.kernel.org/r/20241025-pci-pwrctl-rework-v2-3-568756156cbe@linaro.org
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[bhelgaas: squash fix from
https://lore.kernel.org/r/20241120062459.6371-1-manivannan.sadhasivam@linaro.org
for SPARCv9 issue reported by Jonathan Currier <dullfire@yahoo.com>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: wrap code to 80 columns]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: stable+noautosel@kernel.org # Depends on power supply check
|
|
Currently, pwrctl devices are created if the corresponding PCI nodes are
defined in devicetree. But this is not correct, because not all PCI nodes
require pwrctl support. Pwrctl comes into the picture only when the device
requires kernel to manage its power state. This can be determined using the
power supply properties present in the devicetree node of the device.
Add of_pci_supply_present() to check whether the devicetree contains at
least one power supply property for a device. If one is present, create a
pwrctl device for that PCI node.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 8fb18619d910 ("PCI/pwrctl: Create platform devices for child OF nodes of the port node")
Link: https://lore.kernel.org/r/20241025-pci-pwrctl-rework-v2-2-568756156cbe@linaro.org
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[bhelgaas: rename of_pci_is_supply_present() to of_pci_supply_present() for
readability]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: stable+noautosel@kernel.org # Depends on of_platform_device_create() rework
|
|
The of_platform_populate() API creates platform devices by descending
through the children of the parent node. But it provides no control over
the child nodes, which makes it difficult to add checks for the child
nodes in the future.
Use of_platform_device_create() and for_each_child_of_node_scoped() to make
it possible to add checks for each node before creating the platform
device.
Link: https://lore.kernel.org/r/20241025-pci-pwrctl-rework-v2-1-568756156cbe@linaro.org
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"Nothing particular important in the SoC driver updates, just the usual
improvements to for drivers/soc and a couple of subsystems that don't
fit anywhere else:
- The largest set of updates is for Qualcomm SoC drivers, extending
the set of supported features for additional SoCs in the QSEECOM,
LLCC and socinfo drivers.a
- The ti_sci firmware driver gains support for power managment
- The drivers/reset subsystem sees a rework of the microchip sparx5
and amlogic reset drivers to support additional chips, plus a few
minor updates on other platforms
- The SCMI firmware interface driver gains support for two protocol
extensions, allowing more flexible use of the shared memory area
and new DT binding properties for configurability.
- Mediatek SoC drivers gain support for power managment on the MT8188
SoC and a new driver for DVFS.
- The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
and a few bugfixes
- The Hisilicon Kunpeng HCCS driver gains support for configuring
lanes through sysfs
Finally, there are cleanups and minor fixes for drivers/{soc, bus,
memory}, including changing back the .remove_new callback to .remove,
as well as a few other updates for freescale (powerpc) soc drivers,
NXP i.MX soc drivers, cznic turris platform driver, memory controller
drviers, TI OMAP SoC drivers, and Tegra firmware drivers"
* tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (116 commits)
soc: fsl: cpm1: qmc: Set the ret error code on platform_get_irq() failure
soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
soc: fsl: cpm1: tsa: switch to for_each_available_child_of_node_scoped()
platform: cznic: turris-omnia-mcu: Rename variable holding GPIO line names
platform: cznic: turris-omnia-mcu: Document the driver private data structure
firmware: turris-mox-rwtm: Document the driver private data structure
bus: Switch back to struct platform_driver::remove()
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"Bindings:
- Enable dtc "interrupt_provider" warnings for binding examples. Fix
the warnings in fsl,mu-msi and ti,sci-inta due to this.
- Convert zii,rave-sp-wdt, zii,rave-sp-pwrbutton, and
altr,fpga-passive-serial to DT schema format
- Add some documentation on the different forms of YAML text blocks
which are a constant source of review comments
- Fix some schema errors in constraints for arrays
- Add compatibles for qcom,sar2130p-pdc and onnn,adt7462
DT core:
- Allow overlay kunit tests to run CONFIG_OF_OVERLAY=n
- Add some warnings on deprecated address handling
- Rework early_init_dt_scan() so the arch can pass in the phys
address of the DTB as __pa() is not always valid to use. This fixes
a warning for arm64 with kexec.
- Add and use some new DT graph iterators for iterating over ports
and endpoints
- Rework reserved-memory handling to be sized dynamically for fixed
regions
- Optimize of_modalias() to avoid a strlen() call
- Constify struct device_node and property pointers where ever
possible"
* tag 'devicetree-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (36 commits)
of: Allow overlay kunit tests to run CONFIG_OF_OVERLAY=n
dt-bindings: interrupt-controller: qcom,pdc: Add SAR2130P compatible
of/address: Rework bus matching to avoid warnings
of: WARN on deprecated #address-cells/#size-cells handling
of/fdt: Don't use default address cell sizes for address translation
dt-bindings: Enable dtc "interrupt_provider" warnings
of/fdt: add dt_phys arg to early_init_dt_scan and early_init_dt_verify
dt-bindings: cache: qcom,llcc: Fix X1E80100 reg entries
dt-bindings: watchdog: convert zii,rave-sp-wdt.txt to yaml format
dt-bindings: input: convert zii,rave-sp-pwrbutton.txt to yaml
media: xilinx-tpg: use new of_graph functions
fbdev: omapfb: use new of_graph functions
gpu: drm: omapdrm: use new of_graph functions
ASoC: audio-graph-card2: use new of_graph functions
ASoC: audio-graph-card: use new of_graph functions
ASoC: test-component: use new of_graph functions
of: property: use new of_graph functions
of: property: add of_graph_get_next_port_endpoint()
of: property: add of_graph_get_next_port()
of: module: remove strlen() call in of_modalias()
...
|
|
In addition to a primary endpoint controller, an endpoint function may be
associated with a secondary endpoint controller, epf->sec_epc, to provide
NTB (non-transparent bridge) functionality.
Previously, pci_epc_remove_epf() incorrectly cleared epf->epc instead of
epf->sec_epc when removing from the secondary endpoint controller.
Extend the epc->list_lock coverage and clear either epf->epc or
epf->sec_epc as indicated.
Link: https://lore.kernel.org/r/20241107-epc_rfc-v2-2-da5b6a99a66f@quicinc.com
Fixes: 63840ff53223 ("PCI: endpoint: Add support to associate secondary EPC with EPF")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: reworded subject and description]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
|
|
pci_epc_destroy() invokes pci_bus_release_domain_nr() to release the PCI
domain ID, but there are two issues:
- 'epc->dev' is passed to pci_bus_release_domain_nr() which was already
freed by device_unregister(), leading to a use-after-free issue.
- Domain ID corresponds to the EPC device parent, so passing 'epc->dev'
is also wrong.
Fix these issues by passing 'epc->dev.parent' to
pci_bus_release_domain_nr() and also do it before device_unregister().
Fixes: 0328947c5032 ("PCI: endpoint: Assign PCI domain number for endpoint controllers")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241107-epc_rfc-v2-1-da5b6a99a66f@quicinc.com
[mani: reworded subject and description]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
|
|
The advertised resizable BAR size was fixed in commit 72e34b8593e0 ("PCI:
dwc: endpoint: Fix advertised resizable BAR size").
Commit 867ab111b242 ("PCI: dwc: ep: Add a generic dw_pcie_ep_linkdown()
API to handle Link Down event") was included shortly after this, and
moved the code to another function. When the code was moved, this fix
was mistakenly lost.
According to the spec, it is illegal to not have a bit set in
PCI_REBAR_CAP, and 1 MB is the smallest size allowed.
So, set bit 4 in PCI_REBAR_CAP, so that we actually advertise support
for a 1 MB BAR size.
Fixes: 867ab111b242 ("PCI: dwc: ep: Add a generic dw_pcie_ep_linkdown() API to handle Link Down event")
Link: https://lore.kernel.org/r/20241116005950.2480427-2-cassel@kernel.org
Link: https://lore.kernel.org/r/20240606-pci-deinit-v1-3-4395534520dc@linaro.org
Link: https://lore.kernel.org/r/20240307111520.3303774-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
|
|
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Link: https://lore.kernel.org/r/20241104190714.275977-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
If platform_get_resource_byname() fails and returns NULL because DT lacks
an 'mmio' property for the MHI endpoint, dereferencing res->start will
cause a NULL pointer access. Add a check to prevent it.
Fixes: 1bf5f25324f7 ("PCI: endpoint: Add PCI Endpoint function driver for MHI bus")
Link: https://lore.kernel.org/r/20241105120735.1240728-1-quic_zhonhan@quicinc.com
Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com>
[kwilczynski: error message update per the review feedback]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
pci_epf_test_clean_dma_chan()
Remove a surplus return statement from the void function that has been
added in the commit commit 8353813c88ef ("PCI: endpoint: Enable DMA
tests for endpoints with DMA capabilities").
Especially, as an empty return statements at the end of a void functions
serve little purpose.
This fixes the following checkpatch.pl script warning:
WARNING: void function return statements are not generally useful
#296: FILE: drivers/pci/endpoint/functions/pci-epf-test.c:296:
+ return;
+}
Link: https://lore.kernel.org/r/tencent_F250BEE2A65745A524E2EFE70CF615CA8F06@qq.com
Signed-off-by: Wang Jiang <jiangwang@kylinos.cn>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
Use the dw_pcie_ep_align_addr() function to calculate the alignment in
dw_pcie_ep_raise_{msi,msix}_irq() instead of open coding the same.
Link: https://lore.kernel.org/r/20241017132052.4014605-6-cassel@kernel.org
Link: https://lore.kernel.org/r/20241104205144.409236-2-cassel@kernel.org
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[kwilczynski: squashed patch that fixes memory map sizes]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
6cf57be0f78e ("PCI: Add pcie_get_speed_cap() to find max supported link
speed") and c70b65fb7f12 ("PCI: Add pcie_get_width_cap() to find max
supported link width") added declarations to drivers/pci/pci.h.
576c7218a154 ("PCI: Export pcie_get_speed_cap and pcie_get_width_cap")
subsequently added duplicates to include/linux/pci.h.
Remove the originals from drivers/pci/pci.h. Both interfaces are used by
amdgpu, so they must be in include/linux/pci.h.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
|
|
Add a thermal cooling driver to provide path to access PCIe bandwidth
controller using the usual thermal interfaces.
A cooling device is instantiated for controllable PCIe Ports from the
bwctrl service driver.
If registering the cooling device fails, allow bwctrl's probe to succeed
regardless. As cdev in that case contains IS_ERR() pseudo "pointer", clean
that up inside the probe function so the remove side doesn't need to
suddenly make an odd looking IS_ERR() check.
The thermal side state 0 means no throttling, i.e., maximum supported PCIe
Link Speed.
Link: https://lore.kernel.org/r/20241018144755.7875-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: dropped data->cdev test per
https://lore.kernel.org/r/ZzRm1SJTwEMRsAr8@wunner.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # From the cooling device interface perspective
|
|
Currently, PCIe Link Speeds are adjusted by custom code rather than in a
common function provided in PCI core. The PCIe bandwidth controller
(bwctrl) introduces an in-kernel API, pcie_set_target_speed(), to set PCIe
Link Speed.
Convert Target Speed quirk to use the new API. The Target Speed quirk runs
very early when bwctrl is not yet probed for a Port and can also run later
when bwctrl is already setup for the Port, which requires the per port
mutex (set_speed_mutex) to be only taken if the bwctrl setup is already
complete.
The new API is also intended to be used in an upcoming commit that adds a
thermal cooling device to throttle PCIe bandwidth when thermal thresholds
are reached.
The PCIe bandwidth control procedure is as follows. The highest speed
supported by the Port and the PCIe device which is not higher than the
requested speed is selected and written into the Target Link Speed in the
Link Control 2 Register. Then bandwidth controller retrains the PCIe Link.
Bandwidth Notifications enable the cur_bus_speed in the struct pci_bus to
keep track PCIe Link Speed changes. While Bandwidth Notifications should
also be generated when bandwidth controller alters the PCIe Link Speed, a
few platforms do not deliver LMBS interrupt after Link Training as
expected. Thus, after changing the Link Speed, bandwidth controller makes
additional read for the Link Status Register to ensure cur_bus_speed is
consistent with the new PCIe Link Speed.
Link: https://lore.kernel.org/r/20241018144755.7875-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: squash devm_mutex_init() error checking from
https://lore.kernel.org/r/20241030163139.2111689-1-andriy.shevchenko@linux.intel.com,
drop export of pcie_set_target_speed()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This mostly reverts the commit b4c7d2076b4e ("PCI/LINK: Remove bandwidth
notification"). An upcoming commit extends this driver building PCIe
bandwidth controller on top of it.
PCIe bandwidth notifications were first added in the commit e8303bb7a75c
("PCI/LINK: Report degraded links via link bandwidth notification") but
later had to be removed. The significant changes compared with the old
bandwidth notification driver include:
1) Don't print the notifications into kernel log, just keep the Link
Speed cached in struct pci_bus updated. While somewhat unfortunate,
the log spam was the source of complaints that eventually lead to
the removal of the bandwidth notifications driver (see the links
below for further information).
2) Besides the Link Bandwidth Management Interrupt, also enable Link
Autonomous Bandwidth Interrupt to cover the other source of bandwidth
changes.
3) Handle Link Speed updates robustly. Refresh the cached Link Speed
when enabling Bandwidth Notification Interrupts, and solve the race
between Link Speed read and LBMS/LABS update in
pcie_bwnotif_irq_thread().
4) Use concurrency safe LNKCTL RMW operations.
5) The driver is now called PCIe bwctrl (bandwidth controller) instead
of just bandwidth notifications because of increased scope and
functionality within the driver.
6) Coexist with the Target Link Speed quirk in pcie_failed_link_retrain().
Provide LBMS counting API for it.
7) Tweaks to variable/functions names for consistency and length reasons.
Bandwidth Notifications enable the cur_bus_speed in the struct pci_bus to
keep track PCIe Link Speed changes.
[bhelgaas: This is based on previous work by Alexandru Gagniuc
<mr.nuke.me@gmail.com>; see e8303bb7a75c ("PCI/LINK: Report degraded links
via link bandwidth notification")]
Link: https://lore.kernel.org/r/20241018144755.7875-7-ilpo.jarvinen@linux.intel.com
Link: https://lore.kernel.org/all/20190429185611.121751-1-helgaas@kernel.org/
Link: https://lore.kernel.org/linux-pci/20190501142942.26972-1-keith.busch@intel.com/
Link: https://lore.kernel.org/linux-pci/20200115221008.GA191037@google.com/
Suggested-by: Lukas Wunner <lukas@wunner.de> # Building bwctrl on top of bwnotif
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: squash fix to drop IRQF_ONESHOT and convert to hardirq handler:
https://lore.kernel.org/r/20241115165717.15233-1-ilpo.jarvinen@linux.intel.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Wangxun FF5xxx NICs are similar to SFxxx, RP1000 and RP2000 NICs. They may
be multi-function devices, but they do not advertise an ACS capability.
But the hardware does isolate FF5xxx functions as though it had an ACS
capability and PCI_ACS_RR and PCI_ACS_CR were set in the ACS Control
register, i.e., all peer-to-peer traffic is directed upstream instead of
being routed internally.
Add ACS quirk for FF5xxx NICs in pci_quirk_wangxun_nic_acs() so the
functions can be in independent IOMMU groups.
Link: https://lore.kernel.org/r/E16053DB2B80E9A5+20241115024604.30493-1-mengyuanlou@net-swift.com
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Fix typos and whitespace errors.
Link: https://lore.kernel.org/r/20241102174537.1362183-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
When populating "ranges" property for a PCI bridge or endpoint,
of_pci_prop_ranges() incorrectly uses the CPU address of the resource. In
such PCI nodes, the window should instead be in PCI address space. Call
pci_bus_address() on the resource in order to obtain the PCI bus address.
[Previous discussion at:
https://lore.kernel.org/all/8b4fa91380fc4754ea80f47330c613e4f6b6592c.1724159867.git.andrea.porta@suse.com/]
Link: https://lore.kernel.org/r/20241108094256.28933-1-andrea.porta@suse.com
Fixes: 407d1a51921e ("PCI: Create device tree node for bridge")
Tested-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
|
|
Add a PCI hotplug controller driver for the OCTEON PCIe device. The OCTEON
PCIe device is a multi-function device where function 0 serves as the PCI
hotplug controller.
There is an out-of-band management console interface to firmware running on
function 0 whereby an administrator can disable functions to save power or
enable them with one of several personalities (virtio-net, virtio-crypto,
NVMe, etc) for the other functions. Function 0 initiates hotplug events
handled by this driver when the other functions are enabled or disabled.
+--------------------------------+
| Root Port |
+--------------------------------+
|
PCIe
|
+---------------------------------------------------------------+
| OCTEON PCIe Multifunction Device |
+---------------------------------------------------------------+
| | | |
| | | |
+---------------------+ +----------------+ +-----+ +----------------+
| Function 0 | | Function 1 | | ... | | Function 7 |
| (Hotplug controller)| | (Hotplug slot) | | | | (Hotplug slot) |
+---------------------+ +----------------+ +-----+ +----------------+
|
|
+-------------------------+
| Controller Firmware |
+-------------------------+
The hotplug controller driver enables hotplugging of non-controller
functions within the same device. During probing, the driver removes
the non-controller functions and registers them as PCI hotplug slots.
These slots are added back by the driver, only upon request from the
device firmware.
The controller uses MSI-X interrupts to notify the host of hotplug
events initiated by the OCTEON firmware. Additionally, the driver
allows users to enable or disable individual functions via sysfs slot
entries, as provided by the PCI hotplug framework.
Link: https://lore.kernel.org/r/20241111134523.2796699-1-sthotton@marvell.com
Co-developed-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
[bhelgaas: use pci_info() when possible]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If a reset is issued to a running device with a driver that didn't register
the notification callbacks, the driver may be unaware of this event and
have an inconsistent view of the device's state. Log a warning of this
event because there's nothing else indicating the event occured, which
could be confusing when debugging such situations.
Link: https://lore.kernel.org/r/20241025222755.3756162-2-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Amey Narkhede <ameynarkhede03@gmail.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The "bus" and "cxl_bus" reset methods reset a device by asserting Secondary
Bus Reset on the bridge leading to the device. These only work if the
device is the only device below the bridge.
Add a sysfs 'reset_subordinate' attribute on bridges that can assert
Secondary Bus Reset regardless of how many devices are below the bridge.
This resets all the devices below a bridge in a single command, including
the locking and config space save/restore that reset methods normally do.
This may be the only way to reset devices that don't support other reset
methods (ACPI, FLR, PM reset, etc).
Link: https://lore.kernel.org/r/20241025222755.3756162-1-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
[bhelgaas: commit log, add capable(CAP_SYS_ADMIN) check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Amey Narkhede <ameynarkhede03@gmail.com>
|
|
The controller driver is the parent device of the PCIe host bridge,
PCI-PCI bridge and PCIe endpoint as shown below.
PCIe controller (Top level parent & parent of host bridge)
|
v
PCIe Host bridge (Parent of PCI-PCI bridge)
|
v
PCI-PCI bridge (Parent of endpoint driver)
|
v
PCIe endpoint driver
Now, when the controller device goes to runtime suspend, PM framework will
check the runtime PM state of the child device (host bridge) and will find
it to be disabled. So it will allow the parent (controller device) to go to
runtime suspend. Only if the child device's state was 'active' it will
prevent the parent to get suspended.
It is a property of the runtime PM framework that it can only follow
continuous dependency chains. That is, if there is a device with runtime
PM disabled in a dependency chain, runtime PM cannot be enabled for devices
below it and above it in that chain both at the same time.
Since runtime PM is disabled for host bridge, the state of the child
devices under the host bridge is not taken into account by PM framework for
the top level parent, PCIe controller. So the PM framework allows the
controller driver to enter runtime PM irrespective of the state of the
devices under the host bridge. And this causes the topology breakage and
also possible PM issues like controller driver going to runtime suspend
while the endpoint driver is doing transfers.
Because of the above, in order to enable runtime PM for a PCIe controller
device, one needs to ensure that runtime PM is enabled for all devices in
every dependency chain between it and any PCIe endpoint (as runtime PM is
enabled for PCIe endpoints).
This means that runtime PM needs to be enabled for the host bridge device,
which is present in all of these dependency chains.
After this change, the host bridge device will be runtime-suspended by the
runtime PM framework automatically after suspending its last child and it
will be runtime-resumed automatically before resuming its first child which
will allow the runtime PM framework to track dependencies between the host
bridge device and all of its descendants.
The PM framework expects parent runtime PM to be enabled before enabling
runtime PM of the child. Ensure pm_runtime_enable() is called for the
controller drivers before calling pci_host_probe().
Link: https://lore.kernel.org/r/20241111-runtime_pm-v7-2-9c164eefcd87@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
A PCI controller device, e.g., StarFive, is parent to PCI host bridge
device. We must enable runtime PM of the controller before enabling runtime
PM of the host bridge, which will happen in pci_host_probe(), to avoid this
warning:
pcie-starfive 940000000.pcie: Enabling runtime PM for inactive device with active children
Fix this issue by enabling StarFive controller device's runtime PM before
calling pci_host_probe() in plda_pcie_host_init().
Link: https://lore.kernel.org/r/20241111-runtime_pm-v7-1-9c164eefcd87@quicinc.com
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Remove a surplus semicolon and fix the following warning:
./drivers/pci/controller/pcie-mediatek-gen3.c:414:2-3: Unneeded semicolon
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=11789
Link: https://lore.kernel.org/r/20241111010935.20208-1-yang.lee@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
The "phy-names" property is optional, so the message indicating its
absence during the probe should be of "info" severity rather than
"error" severity.
Link: https://lore.kernel.org/r/20241018113045.2050295-1-bwawrzyn@cisco.com
Signed-off-by: Bartosz Wawrzyniak <bwawrzyn@cisco.com>
[kwilczynski: update log messages wording, commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
soc/drivers
Reset controller updates for v6.13
* Split the Amlogic reset-meson driver into platform and auxiliary
bus drivers. Add support for the reset controller in the G12 and
SM1 audio clock controllers.
* Replace the list of boolean parameters to the internal
reset_control_get functions with an enum reset_flags bitfield,
to make the code more self-descriptive.
* Add devres helpers to request pre-deasserted (and automatically
re-asserting during cleanup) reset controls. This allows reducing
boilerplate in drivers that deassert resets for the lifetime of a
device.
* Use the new auto-deasserting devres helpers in reset-uniphier-glue
as an example.
* Add support for the LAN966x PCI device in drivers/misc, as a
dependency for the following reset-microchip-sparx5 patches.
* Add support for being used on the LAN966x PCI device to the
reset-microchip-sparx5 driver.
Commit 86f134941a4b ("MAINTAINERS: Add the Microchip LAN966x PCI driver
entry") introduces a trivial merge conflict with commit 7280f01e79cc
("net: lan969x: add match data for lan969x") from the net-next tree [1].
[1] https://lore.kernel.org/all/20241101122505.3eacd183@canb.auug.org.au/
* tag 'reset-for-v6.13' of git://git.pengutronix.de/pza/linux: (21 commits)
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
reset: mchp: sparx5: set the dev member of the reset controller
reset: mchp: sparx5: Allow building as a module
reset: mchp: sparx5: Add MCHP_LAN966X_PCI dependency
reset: mchp: sparx5: Map cpu-syscon locally in case of LAN966x
MAINTAINERS: Add the Microchip LAN966x PCI driver entry
misc: Add support for LAN966x PCI device
reset: uniphier-glue: Use devm_reset_control_bulk_get_shared_deasserted()
reset: Add devres helpers to request pre-deasserted reset controls
reset: replace boolean parameters with flags parameter
reset: amlogic: Fix small whitespace issue
reset: amlogic: add auxiliary reset driver support
reset: amlogic: split the device core and platform probe
reset: amlogic: move drivers to a dedicated directory
reset: amlogic: add reset status support
reset: amlogic: use reset number instead of register count
reset: amlogic: add driver parameters
reset: amlogic: make parameters unsigned
reset: amlogic: use generic data matching function
...
Link: https://lore.kernel.org/r/20241105105229.3729474-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There's only one user of pci_walk_bus_locked(), and it's internal to the
PCI core. Unexport it and make it private to drivers/pci/.
Link: https://lore.kernel.org/r/20241022224851.340648-6-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
[bhelgaas: move decl to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The Target Speed quirk in pcie_failed_link_retrain() uses the presence of
LBMS bit as one of the triggering conditions, effectively monopolizing the
use of that bit. An upcoming change will introduce a PCIe bandwidth
controller which sets up an interrupt to track LBMS. As LBMS will be
cleared by the interrupt handler, the Target Speed quirk will no longer be
able to observe LBMS directly.
As a preparatory step for the change, extract the LBMS seen check from
pcie_failed_link_retrain() into a new function pcie_lmbs_seen().
Link: https://lore.kernel.org/r/20241018144755.7875-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
