| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Maxim MAX77705:
- Added core MFD driver.
- Added charger driver.
- Added devicetree bindings for the charger and MFD core.
- Added Haptic controller support via the input subsystem.
- Added LED support.
- Added support to simple-mfd-i2c for fuel gauge and hwmon.
Samsung S2MPU05 (Exynos7870 PMIC):
- Added core MFD support.
- Added Regulator support for 21 LDOs and 5 BUCKs.
- Added devicetree bindings for regulators and the PMIC core.
TI TPS65215 & TPS65214:
- Added support to the existing TPS65219 driver.
- Added devicetree bindings.
STMicroelectronics STM32MP25:
- Added support to the stm32-timers MFD driver.
- Added devicetree bindings.
Congatec Board Controller (CGBC):
- Added HWMON support for internal sensors.
- Added support for the conga-SA8 module.
Microchip LAN969X:
- Enabled the at91-usart MFD driver for this architecture.
MediaTek MT6359:
- Added mfd_cell for mt6359-accdet to allow its driver to probe.
Other misc driver updates:
- AXP20X (AXP717): Added AXP717_TS_PIN_CFG register to writeable regs
for temperature sensor configuration.
- SM501: Switched to using BIT() macro to mitigate potential integer
overflows in GPIO functions.
- ENE KB3930: Added a NULL pointer check for off_gpios during probe
to prevent potential dereference.
- SYSCON: Added a check for invalid resource size to prevent issues
from DT misconfiguration.
- CGBC: Corrected signedness issues in cgbc_session_request
- intel_soc_pmic_chtdc_ti / intel_soc_pmic_crc: Removed unneeded
explicit assignment to REGCACHE_NONE.
- ipaq-micro / tps65010: Switched to using str_enable_disable()
helpers for clarity and potential size reduction.
- upboard-fpga: Removed unnecessary ACPI_PTR() annotation.
- max8997: Removed unused max8997_irq_exit() function, using devm_*
helpers instead.
- lp3943: Dropped unused #include <linux/pwm.h> from the header file.
- db8500-prcmu: Removed needless return statements in void APIs.
- qnap-mcu: Replaced commas with semicolons between expressions for
correctness.
- STA2X11: Removed the core MFD driver as the underlying platform
support was removed.
- EZX-PCAP: Removed the unused pcap_adc_sync function.
- PCF50633 (OpenMoko PMIC): Removed the entire driver (core, adc,
gpio, irq) as the underlying s3c24xx platform support was removed.
Devicetree updates:
- Converted fsl,mcu-mpc8349emitx binding to YAML
- Added qcom,msm8937-tcsr compatible
- Added microchip,sama7d65-flexcom compatible
- Added rockchip,rk3528-qos syscon compatible
- Added airoha,en7581-pbus-csr syscon compatible
- Added microchip,sama7d65-ddr3phy syscon compatible
- Added microchip,sama7d65-sfrbu syscon compatible"
* tag 'mfd-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (49 commits)
mfd: cgbc-core: Add support for conga-SA8
dt-bindings: mfd: syscon: Add microchip,sama7d65-sfrbu
dt-bindings: mfd: syscon: Add microchip,sama7d65-ddr3phy
mfd: cgbc: Add support for HWMON
dt-bindings: mfd: syscon: Add the pbus-csr node for Airoha EN7581 SoC
mfd: cgbc-core: Cleanup signedness in cgbc_session_request()
mfd: pcf50633: Remove remaining PCF50633 support
mfd: pcf50633: Remove unused platform IRQ code
mfd: pcF50633-gpio: Remove unused driver
mfd: pcf50633-adc: Remove unused driver
mfd: qnap-mcu: Convert commas to semicolons in qnap_mcu_exec()
mfd: mt6397-core: Add mfd_cell for mt6359-accdet
dt-bindings: mfd: syscon: Add rk3528 QoS register compatible
dt-bindings: mfd: atmel,sama5d2-flexcom: Add microchip,sama7d65-flexcom
mfd: ezx-pcap: Remove unused pcap_adc_sync
mfd: db8500-prcmu: Remove needless return in three void APIs
mfd: Remove STA2x11 core driver
mfd: max77620: Allow building as a module
mfd: ene-kb3930: Fix a potential NULL pointer dereference
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8937
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been a very quiet release, we've got support for one device
added, another removed, and some smaller fixes and API improvements.
The main thing of note is the rework of the PCA9450 LDO5 handling.
- A rework of the handling of LDO5 on the PCA9450, this was quite
wrong in how it handled the SD_VSEL conrol and only worked for some
system designs. This includes a DTS update since there was a not
quite ABI compatible change as part of the fix
- A devres change introducing devm_kmemdup_array() was pulled in so
it could be used with some regulator conversions to that function,
this pulled in some other devres and IIO stuff that was part of the
same pull request
- Removal of the PCF50633 driver, the SoC for the OpenMoko platform
that used it has been removed
- Support for the NXP PF9453"
* tag 'regulator-v6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (24 commits)
regulator: axp20x: AXP717: dcdc4 doesn't have delay
regulator: dt-bindings: rtq2208: Cleanup whitespace
regulator: dt-bindings: rtq2208: Mark fixed LDO VOUT property as deprecated
regulator: rtq6752: make const read-only array fault_mask static
regulator: pf9453: add PMIC PF9453 support
regulator: dt-bindings: pca9450: Add nxp,pf9453 compatible string
regulator: pcf50633-regulator: Remove
regulator: pca9450: Handle hardware with fixed SD_VSEL for LDO5
regulator: cros-ec: use devm_kmemdup_array()
regulator: devres: use devm_kmemdup_array()
regulator: Add (devm_)of_regulator_get()
devres: Introduce devm_kmemdup_array()
iio: imu: st_lsm9ds0: Replace device.h with what is needed
driver core: Split devres APIs to device/devres.h
err.h: move IOMEM_ERR_PTR() to err.h
regulator: pca9450: Remove duplicate code in probe
regulator: ad5398: Fix incorrect power down bit mask
regulator: pca9450: Fix enable register for LDO5
regulator: pca9450: Fix control register for LDO5
Revert "regulator: pca9450: Add SD_VSEL GPIO for LDO5"
...
|
|
rk806_set_mode_dcdc()
If 'ctr_bit' is negative, the shift counts become negative, causing a
shift of bounds and undefined behavior.
Presumably that's not possible in normal operation, but the code
generation isn't optimal. And undefined behavior should be avoided
regardless.
Improve code generation and remove the undefined behavior by converting
the signed variables to unsigned.
Fixes the following warning with an UBSAN kernel:
vmlinux.o: warning: objtool: rk806_set_mode_dcdc() falls through to next function rk806_get_mode_dcdc()
vmlinux.o: warning: objtool: .text.rk806_set_mode_dcdc: unexpected end of section
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/2023abcddf3f524ba478d64339996f25dc4097d2.1742852847.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/oe-kbuild-all/202503182350.52KeHGD4-lkp@intel.com/
|
|
According to AXP717 user manual, DCDC4 doesn't have a ramp delay like
DCDC1/2/3 do.
Remove it from the description and cleanup the macros.
Signed-off-by: Philippe Simons <simons.philippe@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://patch.msgid.link/20250318205147.42850-1-simons.philippe@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Don't populate the const read-only array fault_mask on the stack at run
time, instead make it static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://patch.msgid.link/20250317165845.525593-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the hidden bank register to identify whether the LDO voltage is
fixed or variable. Remove the read of 'richtek,fixed-microvolt'
property.
Fixes: af1296d15d89 ("regulator: rtq2208: Add fixed LDO VOUT property and check that matches the constraints")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://patch.msgid.link/dae0321b710518ce32260336e3cc9caf2ba84215.1742204502.git.cy_huang@richtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the hidden bank RG to get the correct buck converter phase mapping.
Fixes: 85a11f55621a ("regulator: rtq2208: Add Richtek RTQ2208 SubPMIC")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://patch.msgid.link/ae3245aa713f76000dbd20b4ad6f66d30611d3b8.1742204502.git.cy_huang@richtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the core detects permanent regulator hardware failure or imminent
power failure of a critical supply, it will call hw_protection_shutdown in
an attempt to do a limited orderly shutdown followed by powering off the
system.
This doesn't work out well for many unattended embedded systems that don't
have support for shutdown and that power on automatically when power is
supplied:
- A brief power cycle gets detected by the driver
- The kernel powers down the system and SoC goes into shutdown mode
- Power is restored
- The system remains oblivious to the restored power
- System needs to be manually power cycled for a duration long enough
to drain the capacitors
Allow users to fix this by calling the newly introduced
hw_protection_trigger() instead: This way the hw_protection commandline or
sysfs parameter is used to dictate the policy of dealing with the
regulator fault.
Link: https://lkml.kernel.org/r/20250217-hw_protection-reboot-v3-8-e1c09b090c0c@pengutronix.de
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Cc: Benson Leung <bleung@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Matteo Croce <teknoraver@meta.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Rob Herring (Arm) <robh@kernel.org>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Support new PMIC PF9453, which is totally difference with PCA9450. So
create new file for it.
The PF9453 is a single chip Power Management IC (PMIC) specifically
designed for i.MX 91 processor. It provides power supply solutions for IoT
(Internet of Things), smart appliance, and portable applications where size
and efficiency are critical. The device provides four high efficiency
step-down regulators, three LDOs, one 400 mA load switch and 32.768 kHz
crystal oscillator driver.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250314-pf9453-v5-2-ab0cf1f871b0@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The dummy regulator driver does not need to create a platform device, it
only did so because it was simple to do. Change it over to use the
faux bus instead as this is NOT a real platform device, and it makes
the code even smaller than before.
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/2025021027-outclass-stress-59dd@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Due to asynchronous driver probing there is a chance that the dummy
regulator hasn't already been probed when first accessing it.
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Link: https://patch.msgid.link/20250313103051.32430-3-ceggers@arri.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
S2MPU05 is a PMIC by manufactured by Samsung, particularly used in
Exynos7870 based devices. Add driver support for controlling its 21 LDO
and 5 BUCK regulators.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250301-exynos7870-pmic-regulators-v3-3-808d0b47a564@disroot.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The pcf50633 was used as part of the OpenMoko devices but
the support for its main chip was recently removed in:
commit 61b7f8920b17 ("ARM: s3c: remove all s3c24xx support")
See https://lore.kernel.org/all/Z8z236h4B5A6Ki3D@gallifrey/
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://patch.msgid.link/20250311014959.743322-6-linux@treblig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sometimes I get a NULL pointer dereference at boot time in kobject_get()
with the following call stack:
anatop_regulator_probe()
devm_regulator_register()
regulator_register()
regulator_resolve_supply()
kobject_get()
By placing some extra BUG_ON() statements I could verify that this is
raised because probing of the 'dummy' regulator driver is not completed
('dummy_regulator_rdev' is still NULL).
In the JTAG debugger I can see that dummy_regulator_probe() and
anatop_regulator_probe() can be run by different kernel threads
(kworker/u4:*). I haven't further investigated whether this can be
changed or if there are other possibilities to force synchronization
between these two probe routines. On the other hand I don't expect much
boot time penalty by probing the 'dummy' regulator synchronously.
Cc: stable@vger.kernel.org
Fixes: 259b93b21a9f ("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Link: https://patch.msgid.link/20250311091803.31026-1-ceggers@arri.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently, we are unnecessarily holding a regulator_ww_class_mutex lock
when creating debugfs entries for a newly created regulator. This was
brought up as a concern in the discussion in commit cba6cfdc7c3f
("regulator: core: Avoid lockdep reports when resolving supplies").
This causes the following lockdep splat after executing
`ls /sys/kernel/debug` on my platform:
======================================================
WARNING: possible circular locking dependency detected
5.15.167-axis9-devel #1 Tainted: G O
------------------------------------------------------
ls/2146 is trying to acquire lock:
ffffff803a562918 (&mm->mmap_lock){++++}-{3:3}, at: __might_fault+0x40/0x88
but task is already holding lock:
ffffff80014497f8 (&sb->s_type->i_mutex_key#3){++++}-{3:3}, at: iterate_dir+0x50/0x1f4
which lock already depends on the new lock.
[...]
Chain exists of:
&mm->mmap_lock --> regulator_ww_class_mutex --> &sb->s_type->i_mutex_key#3
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&sb->s_type->i_mutex_key#3);
lock(regulator_ww_class_mutex);
lock(&sb->s_type->i_mutex_key#3);
lock(&mm->mmap_lock);
*** DEADLOCK ***
This lock dependency still exists on the latest kernel and using a newer
non-tainted kernel would still cause this problem.
Fix by moving sysfs symlinking and creation of debugfs entries to after
the release of the regulator lock.
Fixes: cba6cfdc7c3f ("regulator: core: Avoid lockdep reports when resolving supplies")
Fixes: eaa7995c529b ("regulator: core: avoid regulator_resolve_supply() race condition")
Signed-off-by: Ludvig Pärsson <ludvig.parsson@axis.com>
Link: https://patch.msgid.link/20250305-regulator_lockdep_fix-v1-1-ab938b12e790@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are two ways to set the output voltage of the LD05
regulator. First by writing to the voltage selection registers
and second by toggling the SD_VSEL signal.
Usually board designers connect SD_VSEL to the VSELECT signal
controlled by the USDHC controller, but in some cases the
signal is hardwired to a fixed low level (therefore selecting
3.3V as initial value for allowing to boot from the SD card).
In these cases, the voltage is only determined by the value
of the LDO5CTRL_L register. Introduce a property
nxp,sd-vsel-fixed-low to let the driver know that SD_VSEL
is low and there is no GPIO to actually get that
information from dynamically.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://patch.msgid.link/20250303132258.50204-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Raag Jadav <raag.jadav@intel.com>:
This series converts regulator drivers to use the newly introduced[1]
devm_kmemdup_array() helper.
[1] https://lore.kernel.org/r/20250212062513.2254767-1-raag.jadav@intel.com
|
|
Convert to use devm_kmemdup_array() and while at it, make the size robust
against type changes.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Link: https://patch.msgid.link/20250228072057.151436-3-raag.jadav@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Convert to use devm_kmemdup_array() which is more robust.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Link: https://patch.msgid.link/20250228072057.151436-2-raag.jadav@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Sebastian Reichel <sebastian.reichel@collabora.com>:
This introduces devm_of_regulator_get without the _optional suffix, since
that is more sensible for the Rockchip usecase.
|
|
The Rockchip power-domain controller also plans to make use of
per-domain regulators similar to the MediaTek power-domain controller.
Since existing DTs are missing the regulator information, the kernel
should fallback to the automatically created dummy regulator if
necessary. Thus the version without the _optional suffix is needed.
The Rockchip driver plans to use the managed version, but to be
consistent with existing code the unmanaged version is added at the
same time.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patch.msgid.link/20250220-rk3588-gpu-pwr-domain-regulator-v6-1-a4f9c24e5b81@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SD_VSEL GPIO is fetched twice for no reason. Remove the
duplicate code.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://patch.msgid.link/20250219080152.11883-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This reverts commit cd7a38c40b231350a3cd0fd774f4e6bb68c4b411.
When submitting the change above, it was thought that the origin of the
init_data should be a clear choice, from the driver or from DT but not
both.
It turns out some devices, such as qcom-msm8974-lge-nexus5-hammerhead,
relied on the old behaviour to override the init_data provided by the
driver, making it some kind of default if none is provided by the platform.
Using the init_data provided by the driver when it is present broke these
devices so revert the change to fixup the situation and add a comment
to make things a bit more clear
Reported-by: Luca Weiss <luca@lucaweiss.eu>
Closes: https://lore.kernel.org/lkml/5857103.DvuYhMxLoT@lucaweiss.eu
Fixes: cd7a38c40b23 ("regulator: core: do not silently ignore provided init_data")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patch.msgid.link/20250211-regulator-init-data-fixup-v1-1-5ce1c6cff990@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
AD5398_SW_POWER_DOWN was defined with a bit position outside the valid
range of the device's 16-bit register. The bitwise operation with an
unsigned short would always evaluate to 0, making the power down check
ineffective.
Update AD5398_SW_POWER_DOWN to use a valid bit position within the
16-bit range of the register.
Fixes: 19d022d67d73 ("regulator: ad5398: change enable bit name to improve readibility")
Signed-off-by: Dheeraj Reddy Jonnalagadda <dheeraj.linuxdev@gmail.com>
Link: https://patch.msgid.link/20250206103153.59114-1-dheeraj.linuxdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Isaac Scott <isaac.scott@ideasonboard.com>:
The AD5398 is a DAC that can be used to control current flow in circuits
in a wide variety of applications such as motor control, or in my case,
LED control. I found when working with the current driver that it did
not work for my use case. It transpired that it only had support for
platform_data, and didn't appear to be correctly implemented according
to the datasheet, which can be found here:
https://www.analog.com/media/en/technical-documentation/data-sheets/ad5398.pdf
One example of this is the "soft power-down" bit being referred to in
the driver as simply "enable", which gives the impression that the
setting that bit will allow current through the regulator, which it does
not.
This series allows the regulator to be given its constraints via the
device tree, and makes the function of the enable register much more
obvious.
|
|
The LDO5 regulator has two configuration registers, but only
LDO5CTRL_L contains the bits for enabling/disabling the regulator.
Fixes: 0935ff5f1f0a ("regulator: pca9450: add pca9450 pmic driver")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://patch.msgid.link/20241218152842.97483-6-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For LDO5 we need to be able to check the status of the SD_VSEL input in
order to know which control register is used. Read the status of the
SD_VSEL signal via GPIO and use the correct register accordingly.
To use this, the LDO5 node in the devicetree needs the sd-vsel-gpios
property to reference the GPIO that is used to read back the SD_VSEL
status internally. Please note that the SION bit in the IOMUX must be
set if the signal is muxed as VSELECT and controlled by the USDHC
controller.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://patch.msgid.link/20241218152842.97483-5-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This reverts commit 8c67a11bae889f51fe5054364c3c789dfae3ad73.
It turns out that all boards using the PCA9450 actually have the
SD_VSEL input connected to the VSELECT signal of the SoCs SD/MMC
interface or use a fixed level.
The assumptions on which this was implemented were wrong. There
is no need for a GPIO-only-based approach and keeping this will
cause confusion and lead people to implement non-standard setups.
All in-tree users of this have been migrated and we can savely
remove this now and allow for a more future-proof approach
of syncing the actual status of SD_VSEL and the PMIC driver.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://patch.msgid.link/20241218152842.97483-4-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Previously, the ad5398 driver used only platform_data, which is
deprecated in favour of device tree. This caused the AD5398 to fail to
probe as it could not load its init_data. If the AD5398 has a device
tree node, pull the init_data from there using
of_get_regulator_init_data.
Signed-off-by: Isaac Scott <isaac.scott@ideasonboard.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://patch.msgid.link/20250128173143.959600-4-isaac.scott@ideasonboard.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The mask name AD5398_CURRENT_EN_MASK is misleading, as it implies that
setting bit 16 of the AD5398 enables current flow. In fact, setting this
bit prevents current flow, due to this bit being a software power down
control. This bit is referred to as "soft power down" in the datasheet.
As such, change the name of the bit and modify its use in the driver to
make the regulator more intuitively usable.
(When calling ad5398_enable, current will start flowing, and vice
versa).
Signed-off-by: Isaac Scott <isaac.scott@ideasonboard.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://patch.msgid.link/20250128173143.959600-2-isaac.scott@ideasonboard.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of fixes that have come in during the merge window: one that
operates the TPS6287x devices more within the design spec and can
prevent current surges when changing voltages and another more trivial
one for error message formatting"
* tag 'regulator-fix-v6.14-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Add missing newline character
regulator: TPS6287X: Use min/max uV to get VRANGE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This was a very quiet release, aside from some smaller improvements we
have:
- Support for power budgeting on regulators, initially targeted at
some still in review support for PSE controllers but generally
useful
- Support for error interrupts from ROHM BD96801 devices
- Support for NXP PCA9452"
* tag 'regulator-v6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: dt-bindings: Add regulator-power-budget-milliwatt property
regulator: Add support for power budget
regulator: core: Resolve supply using of_node from regulator_config
regulator: of: Implement the unwind path of of_regulator_match()
regulator: tps65219: Remove debugging helper function
regulator: tps65219: Remove MODULE_ALIAS
regulator: tps65219: Update driver name
regulator: tps65219: Use dev_err_probe() instead of dev_err()
regulator: dt-bindings: mt6315: Drop regulator-compatible property
regulator: pca9450: Add PMIC pca9452 support
regulator: dt-bindings: pca9450: Add pca9452 support
regulator: pca9450: Use dev_err_probe() to simplify code
regulator: pca9450: add enable_value for all bucks
regulator: bd96801: Add ERRB IRQ
|
|
dev_err_probe() error messages need newline character.
Fixes: 6eabfc018e8d ("regulator: core: Allow specifying an initial load w/ the bulk API")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://patch.msgid.link/20250122072019.1926093-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Changing voltage might ignore slew rate and cause a current surge.
With current implementation the driver will get the regulator to change
the voltage range used during run time. According to communication I
have had with Texas Instruments, this is not intended, since the
Dynamic Voltage Scaling in the hardware is only designed to work
within a voltage range. The current implementation will therefore
ignore the slew rate that is defined in devicetree when the voltage
range is changed during use.
The current implementation will always select a voltage in the most
accurate range that can reach that voltage even though multiple ranges
are able to reach that voltage. There are 4 Voltage ranges with the
following reach:
0b00: 0.4-0.71875V (1.25mV step size)
0b01: 0.4-1.0375V (2.5mV)
0b10: 0.4-1.675V (5mV)
0b11: 0.8-3.3V (10mV)
This in practice means that a change from below to above 0.71875V will
use the smallest range(0b00) for the values below and the second
smallest range(0b01) for the voltages above (Up to 1.675V). I have
timed how long it takes to go from below 0.71875V to above. The
increase was 100mV which, with the slew rate set to 1250µV/µs. This
in theory should take 80µs to do. With the current implementation, it
takes 10µs on my hardware. Doing the same test with the slew rate set
to 5000µV/µs, which should take 20µs, also only takes 10µs to do on
my hardware. Not only is this not in line with the technical
specification for the regulator. It also causes a current surge. Which
when calculating the output current, as described in the technical
specification, compared to what I could observe on my hardware the real
output is ~1A higher (~1.2A) than what I calculated it to be(~0.2A).
I tested also transitioning from a bigger to a smaller range, and the
results were the same.
Instead, let's limit the voltage range to a single one, which is in
line with the intended use of the regulator. This is done by looking
up the minimum and maximum requested voltage specified in devicetree.
Signed-off-by: Jonas Andreasson <jonas.andreasson@axis.com>
Link: https://patch.msgid.link/20250121-tps-fix-v2-1-50cc4d0f1635@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Introduce power budget management for the regulator device. Enable tracking
of available power capacity by providing helpers to request and release
power budget allocations.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250115-feature_regulator_pw_budget-v2-1-0a44b949e6bc@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Previously, the regulator core resolved its supply only from the parent
device or its children, ignoring the of_node specified in the
regulator_config structure.
This behavior causes issues in scenarios where multiple regulator devices
are registered for components described as children of a controller, each
with their own specific regulator supply.
For instance, in a PSE controller with multiple PIs (Power Interfaces),
each PI may have a distinct regulator supply. However, the regulator core
would incorrectly use the PSE controller node or its first child to look up
the regulator supply, rather than the node specified by the
regulator_config->of_node for the PI.
This update modifies the behavior to prioritize the of_node in
regulator_config for resolving the supply. This ensures correct resolution
of the power supply for each device. If no supply is found in the provided
of_node, the core falls back to searching within the parent device as
before.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250109-b4-feature_poe_arrange-v2-13-55ded947b510@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_regulator_match() does not release the OF node reference in the error
path, resulting in an OF node leak. Therefore, call of_node_put() on the
obtained nodes before returning the EINVAL error.
Since it is possible that some drivers call this function and do not
exit on failure, such as s2mps11_pmic_driver, clear the init_data and
of_node in the error path.
This was reported by an experimental verification tool that I am
developing. As I do not have access to actual devices nor the QEMU board
configuration to test drivers that call this function, no runtime test
was able to be performed.
Fixes: 1c8fa58f4750 ("regulator: Add generic DT parsing for regulators")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Link: https://patch.msgid.link/20250104080453.2153592-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The regulator bindings don't document regulator-uv-survival-time-ms, but
the more descriptive regulator-uv-less-critical-window-ms instead.
Looking back at v3[1] and v4[2] of the series adding the support,
the property was indeed renamed between these patch series, but
unfortunately the rename only made it into the DT bindings with the
driver code still using the old name.
Let's therefore rename the property in the driver code to follow suit.
This will break backwards compatibility, but there are no upstream
device trees using the property and we never documented the old name
of the property anyway. ¯\_(ツ)_/¯"
[1]: https://lore.kernel.org/all/20231025084614.3092295-7-o.rempel@pengutronix.de/
[2]: https://lore.kernel.org/all/20231026144824.4065145-5-o.rempel@pengutronix.de/
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://patch.msgid.link/20241218-regulator-uv-survival-time-ms-rename-v1-1-6cac9c3c75da@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This helper function is primarily used by developers for debugging & is
not a standard feature included in other PMIC drivers. The purpose of
debugging function is to check if rdev is determine if the regulator has
been registered prior to requesting a threaded irq. This case is already
handled with the ISERR(rdev) check because the error code is returned.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://patch.msgid.link/20241217204526.1010989-5-s-ramamoorthy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove MODULE_ALIAS because the same module alias is already generated by
MODULE_DEVICE_TABLE.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://patch.msgid.link/20241217204526.1010989-4-s-ramamoorthy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Follow the same naming convention in tps6594-regulator.c with
tpsxxx-regulator instead of tpsxxx-pmic.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://patch.msgid.link/20241217204526.1010989-3-s-ramamoorthy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make the error message format unified by switching from dev_err() to
dev_err_probe() where there is a chance of -EPROBE_DEFER returned. This
helps simplify the error code where possible.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://patch.msgid.link/20241217204526.1010989-2-s-ramamoorthy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the PMIC pca9452 support, which add ldo3 compared with pca9451a.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20241205-pca9450-v1-4-aab448b74e78@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use dev_err_probe() to simplify code.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20241205-pca9450-v1-2-aab448b74e78@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set 'enable_value' in the regulator descriptor for different bucks to
manage their enable modes:
- 00b: OFF
- 01b: ON when PMIC_ON_REQ = H
- 10b: ON when PMIC_ON_REQ = H && PMIC_STBY_REQ = L
- 11b: Always ON
Ensure appropriate behavior based on the intended design. For example:
- Buck2, designed for vddarm, should be set to '10b' (ON when
PMIC_STBY_REQ = L) since it can be off when `PMIC_STBY_REQ = H` after the
kernel enters suspend.
- Other bucks remain '01b' (ON when PMIC_ON_REQ = H), matching the default
setting. This avoids the need to re-enable them during kernel boot as they
are already enabled after PMIC initialization.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20241205-pca9450-v1-1-aab448b74e78@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
AXP717 datasheet says that regulator ramp delay is 15.625 us/step,
which is 10mV in our case.
Add a AXP_DESC_RANGES_DELAY macro and update AXP_DESC_RANGES macro to
expand to AXP_DESC_RANGES_DELAY with ramp_delay = 0
For DCDC4, steps is 100mv
Add a AXP_DESC_DELAY macro and update AXP_DESC macro to
expand to AXP_DESC_DELAY with ramp_delay = 0
This patch fix crashes when using CPU DVFS.
Signed-off-by: Philippe Simons <simons.philippe@gmail.com>
Tested-by: Hironori KIKUCHI <kikuchan98@gmail.com>
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Fixes: d2ac3df75c3a ("regulator: axp20x: add support for the AXP717")
Link: https://patch.msgid.link/20241208124308.5630-1-simons.philippe@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ROHM BD96801 "scalable PMIC" provides two physical IRQs. The ERRB
handling can in many cases be omitted because it is used to inform fatal
IRQs, which usually kill the power from the SOC.
There may however be use-cases where the SOC has a 'back-up' emergency
power source which allows some very short time of operation to try to
gracefully shut down sensitive hardware. Furthermore, it is possible the
processor controlling the PMIC is not powered by the PMIC. In such cases
handling the ERRB IRQs may be beneficial.
Add support for ERRB IRQs.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/ZzWkny4lKpY09SX5@mva-rohm
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of fixes that came in during the merge window, plus
documetation of a new device ID for the Qualcomm LABIBB driver.
There's a core fix for the rarely used current constraints and a fix
for the Qualcomm RPMH driver which had described only one of the two
voltage ranges that the hardware could control, creating a potential
incompatibility with the configuration left by firmware"
* tag 'regulator-fix-v6.13-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Ignore unset max_uA constraints in current limit check
dt-bindings: regulator: qcom-labibb-regulator: document the pmi8950 labibb regulator
regulator: qcom-rpmh: Update ranges for FTSMPS525
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
- Several drivers, including atmel-flexcom/rk8xx-core, palmas, and
tps65010, have undergone minor code improvements to enhance
consistency and fix race conditions.
- The syscon driver now utilizes the regmap max_register_is_0
capability for consistent register map configuration across syscons
of all sizes.
- New device support has been added for QCS8300, qcs615, SA8255p, and
samsung,s2dos05, expanding the range of compatible hardware.
- The cros_ec driver now supports loading cros_ec_ucsi on supported ECs
and avoids loading the charger with UCSI, streamlining functionality.
- The bd96801 driver now utilizes the more modern maple tree register
cache, improving performance.
- The da9052-spi driver has undergone a fix to change the read-mask to
write-mask, preventing potential issues.
- Unused declarations in max77693 have been removed, and support for
samsung,s2dos05 has been added, enhancing code clarity and device
compatibility.
- Error handling in cs42l43 has been fixed to avoid unbalanced
regulator put and ensure proper synchronization during driver
removal.
- The wcd934x driver now uses MODULE_DEVICE_TABLE() instead of
MODULE_ALIAS(), improving code consistency.
- Documentation for qcom,tcsr, syscon, and atmel-smc has been updated
and reorganized for better clarity and maintainability.
- The intel_soc_pmic_bxtwc driver has undergone significant
improvements, including the use of IRQ domains for various devices,
fixing IRQ domain names duplication, and code refactoring for better
consistency and maintainability.
- The ipaq-micro driver has received a fix for a missing break
statement in the default case, enhancing code robustness.
- Support for the AXP323 PMIC has been added to the axp20x driver,
along with ensuring a clear relationship between IDs and model names,
and allowing multiple regulators, broadening hardware compatibility.
- The cs42l43 driver now disables IRQs during suspend for improved
power management.
- The adp5585 driver has reduced its dependencies by dropping the
obsolete dependency on COMPILE_TEST.
- Initial support for the MT6328 PMIC has been added to the mt6397
driver, expanding the range of supported hardware.
- The rtc-bd70528 driver has been simplified by dropping the IC name
from IRQ, improving code readability.
- Documentation for qcom,spmi-pmic, ti,twl, and zii,rave-sp has been
updated to enhance clarity and incorporate new features.
- The rt5033 driver has received a fix for a missing
regmap_del_irq_chip() in the error handling path.
- New device support has been added for MSM8917, and the
intel_soc_pmic_crc driver now supports non-ACPI instantiated
i2c_client.
- The 88pm886 driver has added support for the RTC cell, and the tqmx86
driver has improved its GPIO IRQ setup and added I2C IRQ support,
increasing functionality.
- The sprd,sc2731 DT schema has been updated and converted to YAML
format for better readability and maintainability.
* tag 'mfd-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (62 commits)
dt-bindings: mfd: bd71828: Use charger resistor in mOhm instead of MOhm
dt-bindings: mfd: sprd,sc2731: Convert to YAML
mfd: tqmx86: Add I2C IRQ support
mfd: tqmx86: Make IRQ setup errors non-fatal
mfd: tqmx86: Refactor GPIO IRQ setup
mfd: tqmx86: Improve gpio_irq module parameter description
mfd: tqmx86: Add board definitions for TQMx120UC, TQMx130UC and TQMxE41S
mfd: 88pm886: Add the RTC cell
dt-bindings: mfd: Add Realtek RTL9300 switch peripherals
mfd: intel_soc_pmic_crc: Add support for non ACPI instantiated i2c_client
mfd: intel_soc_pmic_*: Consistently use filename as driver name
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8917
mfd: rt5033: Fix missing regmap_del_irq_chip()
mfd: cgbc-core: Fix error handling paths in cgbc_init_device()
dt-bindings: mfd: aspeed: Support for AST2700
mfd: Switch back to struct platform_driver::remove()
dt-bindings: mfd: qcom,spmi-pmic: Document PMICs added in SM8750
mfd: rtc: bd7xxxx Drop IC name from IRQ
mfd: mt6397: Add initial support for MT6328
mfd: adp5585: Drop obsolete dependency on COMPILE_TEST
...
|
|
We should only consider max_uA constraints if they are explicitly defined.
In cases where it is not set, we should assume the regulator has no current
limit.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20241121-feature_poe_port_prio-v3-2-83299fa6967c@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
