| Age | Commit message (Collapse) | Author |
|---|
|
DW APB/AHB SSI core now supports the procedure automatically detecting the
number of native chip-select lines. Thus there is no longer point in
defaulting to four CS if the platform doesn't specify the real number
especially seeing the default number didn't correspond to any original DW
APB/AHB databook.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240424150657.9678-5-fancer.lancer@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Number of native chip-select lines is either retrieved from the "num-cs"
DT-property or auto-detected in the generic DW APB/AHB SSI probe method.
In the former case the property is supposed to be of the "u32" size.
Convert the field type to being u32 then to be able to drop the temporary
variable afterwards.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240424150657.9678-4-fancer.lancer@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Aside with the FIFO depth and DFS field size it's possible to auto-detect
a number of native chip-select synthesized in the DW APB/AHB SSI IP-core.
It can be done just by writing ones to the SER register. The number of
writable flags in the register is limited by the SSI_NUM_SLAVES IP-core
synthesize parameter. All the upper flags are read-only and wired to zero.
Based on that let's add the number of native CS auto-detection procedure
so the low-level platform drivers wouldn't need to manually set it up
unless it's required to set a constraint due to platform-specific reasons
(for instance, due to a hardware bug).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240424150657.9678-3-fancer.lancer@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since commit dd3e7cba1627 ("ocfs2/dlm: move BITS_TO_BYTES() to bitops.h
for wider use") there is a generic helper available to calculate a number
of bytes needed to accommodate the specified number of bits. Let's use it
instead of the hard-coded DIV_ROUND_UP() macro function.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240424150657.9678-2-fancer.lancer@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On the STM32F4/7, the MOSI and CLK pins float while the controller is
disabled. CS is a regular GPIO, and therefore always driven. Currently,
the controller is enabled in the transfer_one() callback, which runs
after CS is asserted. Therefore, there is a period where the SPI pins
are floating while CS is asserted, making it possible for stray signals
to disrupt communications. An analogous problem occurs at the end of the
transfer when the controller is disabled before CS is released.
This problem can be reliably observed by enabling the pull-up (if
CPOL=0) or pull-down (if CPOL=1) on the clock pin. This will cause two
extra unintended clock edges per transfer, when the controller is
enabled and disabled.
Note that this bug is likely not present on the STM32H7, because this
driver sets the AFCNTR bit (not supported on F4/F7), which keeps the SPI
pins driven even while the controller is disabled.
Enabling/disabling the controller as part of runtime PM was suggested as
an alternative approach, but this breaks the driver on the STM32MP1 (see
[1]). The following quote from the manual may explain this:
> To restart the internal state machine properly, SPI is strongly
> suggested to be disabled and re-enabled before next transaction starts
> despite its setting is not changed.
This patch has been tested on an STM32F746 with a MAX14830 UART
expander.
[1] https://lore.kernel.org/lkml/ZXzRi_h2AMqEhMVw@dell-precision-5540/T/
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Link: https://lore.kernel.org/r/20240424135237.1329001-2-ben.wolsieffer@hefring.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Wolfram Sang <wsa+renesas@sang-engineering.com>:
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_*() functions causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
obvious and self explaining.
This is part of a tree-wide series. The rest of the patches can be found here
(some parts may still be WIP):
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux.git i2c/time_left
Because these patches are generated, I audit them before sending. This is why I
will send series step by step. Build bot is happy with these patches, though.
No functional changes intended.
|
|
Merge series from Lorenzo Bianconi <lorenzo@kernel.org>:
Introduce support for SPI-NAND driver of the Airoha NAND Flash Interface
found on Airoha ARM EN7581 SoCs.
|
|
If spi_sync() is called with the non-empty queue and the same spi_message
is then reused, the complete callback for the message remains set while
the context is cleared, leading to a null pointer dereference when the
callback is invoked from spi_finalize_current_message().
With function inlining disabled, the call stack might look like this:
_raw_spin_lock_irqsave from complete_with_flags+0x18/0x58
complete_with_flags from spi_complete+0x8/0xc
spi_complete from spi_finalize_current_message+0xec/0x184
spi_finalize_current_message from spi_transfer_one_message+0x2a8/0x474
spi_transfer_one_message from __spi_pump_transfer_message+0x104/0x230
__spi_pump_transfer_message from __spi_transfer_message_noqueue+0x30/0xc4
__spi_transfer_message_noqueue from __spi_sync+0x204/0x248
__spi_sync from spi_sync+0x24/0x3c
spi_sync from mcp251xfd_regmap_crc_read+0x124/0x28c [mcp251xfd]
mcp251xfd_regmap_crc_read [mcp251xfd] from _regmap_raw_read+0xf8/0x154
_regmap_raw_read from _regmap_bus_read+0x44/0x70
_regmap_bus_read from _regmap_read+0x60/0xd8
_regmap_read from regmap_read+0x3c/0x5c
regmap_read from mcp251xfd_alloc_can_err_skb+0x1c/0x54 [mcp251xfd]
mcp251xfd_alloc_can_err_skb [mcp251xfd] from mcp251xfd_irq+0x194/0xe70 [mcp251xfd]
mcp251xfd_irq [mcp251xfd] from irq_thread_fn+0x1c/0x78
irq_thread_fn from irq_thread+0x118/0x1f4
irq_thread from kthread+0xd8/0xf4
kthread from ret_from_fork+0x14/0x28
Fix this by also setting message->complete to NULL when the transfer is
complete.
Fixes: ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Link: https://lore.kernel.org/r/20240430182705.13019-1-mans@mansr.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are macros spi_valid_txbuf() and spi_valid_rxbuf() for determining
if an xfer actually intended to send or receive data.
These checks were hard-coded in spi_statistics_add_transfer_stats(). We
can make use of the macros instead to make the code more readable and
more robust against potential future changes in case the definition of
what valid means changes.
The macro takes the spi_message as an argument, so we need to change
spi_statistics_add_transfer_stats() to take the spi_message as an
argument instead of the controller.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240430201530.2138095-3-dlechner@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430114142.28551-9-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240430114142.28551-8-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240430114142.28551-7-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430114142.28551-6-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430114142.28551-5-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240430114142.28551-4-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430114142.28551-3-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430114142.28551-2-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Introduce support for SPI-NAND driver of the Airoha NAND Flash Interface
found on Airoha ARM SoCs.
Tested-by: Rajeev Kumar <Rajeev.Kumar@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/6c9db20505b01a66807995374f2af475a23ce5b2.1714377864.git.lorenzo@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Declare a new mobileye,eyeq5-ospi compatible.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240423-cdns-qspi-mbly-v4-4-3d2a7b535ad0@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Call readl_relaxed_poll_timeout() with no sleep at the start of
cqspi_wait_for_bit(). If its short timeout expires, a sleeping
readl_relaxed_poll_timeout() call takes the relay.
The reason is to avoid hrtimer interrupts on the system. All read
operations are expected to take less than 100µs.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240423-cdns-qspi-mbly-v4-3-3d2a7b535ad0@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Support reads through polling, without any IRQ. The main reason is
performance; profiling shows that the first IRQ comes quickly on our
specific hardware. Once this IRQ arrives, we poll until all data is
retrieved. Avoid initial sleep to reduce IRQ count.
Hide this behavior behind a quirk flag.
This is confirmed through micro-benchmarks, but also end-to-end
performance tests. Mobileye EyeQ5, octal flash, reading 235M on a UBIFS
filesystem:
- No optimizations, ~10.34s, ~22.7 MB/s, 199230 IRQs
- CQSPI_SLOW_SRAM, ~10.34s, ~22.7 MB/s, 70284 IRQs
- CQSPI_RD_NO_IRQ, ~9.37s, ~25.1 MB/s, 521 IRQs
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240423-cdns-qspi-mbly-v4-2-3d2a7b535ad0@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If FIFO depth DT property is provided, check it matches what hardware
reports and warn otherwise. Else, use hardware provided value.
Hardware exposes FIFO depth indirectly because
CQSPI_REG_SRAMPARTITION is partially read-only.
Move probe cqspi->ddata assignment prior to cqspi_of_get_pdata() call.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240423-cdns-qspi-mbly-v4-1-3d2a7b535ad0@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the scope based of_node_put() cleanup in s3c64xx_spi_csinfo to
automatically release the device node with the __free() cleanup handler
Initialize data_np at the point of declaration for clarity of scope.
This change reduces the risk of memory leaks and simplifies the code by
removing manual node put call.
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Shivani Gupta <shivani07g@gmail.com>
Link: https://lore.kernel.org/r/20240418000505.731724-1-shivani07g@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In some cases SPI child devices behind spi-mux require different
settings like: max_speed_hz, mode and bits_per_word.
Typically the slave device driver puts the settings in place and calls
spi_setup() once during probe and assumes they stay in place for all
following spi transfers.
However spi-mux forwarded spi_setup() -call to SPI master driver only
when slave driver calls spi_setup(). If second slave device was
accessed meanwhile and that driver called spi_setup(), the
settings did not change back to the first spi device.
In case of wrong max_speed_hz this caused spi trasfers to fail.
This commit adds spi_setup() call after mux is changed. This way
the right device specific parameters are set to the master driver.
The fix has been tested by using custom hardware and debugging
spi master driver speed settings.
Co-authored-by: Petri Tauriainen <petri.tauriainen@bittium.com>
Signed-off-by: Heikki Keranen <heikki.keranen@bittium.com>
Link: https://lore.kernel.org/r/20240422114150.84426-1-heikki.keranen@bittium.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes: 439fbc97502a ("spi: cs42l43: Add bridged cs35l56 amplifiers")
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240418103315.1487267-1-mstrozek@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240417104730.2510856-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_add_action_or_reset() rather than manually cleaning up on the
error path.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240417093026.79396-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>:
In some cs42l43 systems a couple of cs35l56 amplifiers are attached
to the cs42l43's SPI and I2S. On Windows the cs42l43 is controlled
by a SDCA class driver and these two amplifiers are controlled by
firmware running on the cs42l43. However, under Linux the decision
was made to interact with the cs42l43 directly, affording the user
greater control over the audio system. However, this has resulted
in an issue where these two bridged cs35l56 amplifiers are not
populated in ACPI and must be added manually. There is at least an
SDCA extension unit DT entry we can key off.
The process of adding this is handled using a software node, firstly the
ability to add native chip selects to software nodes must be added.
Secondly, an additional flag for naming the SPI devices is added this
allows the machine driver to key to the correct amplifier. Then finally,
the cs42l43 SPI driver adds the two amplifiers directly onto its SPI
bus.
An additional series will follow soon to add the audio machine driver
parts (in the sof-sdw driver), however that is fairly orthogonal to
this part of the process, getting the actual amplifiers registered.
|
|
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
A couple of additional refactorings on top of the multi-CS support.
One is to make sure that the comment and the code are not disrupted
if additional changes come in the future and second one is f or the
sake of deduplication. In both cases it also makes indentation level
smaller in the affected pieces of the code.
No functional changes intended.
|
|
On some cs42l43 systems a couple of cs35l56 amplifiers are attached
to the cs42l43's SPI and I2S. On Windows the cs42l43 is controlled
by a SDCA class driver and these two amplifiers are controlled by
firmware running on the cs42l43. However, under Linux the decision
was made to interact with the cs42l43 directly, affording the user
greater control over the audio system. However, this has resulted
in an issue where these two bridged cs35l56 amplifiers are not
populated in ACPI and must be added manually.
Check for the presence of the "01fa-cirrus-sidecar-instances" property
in the SDCA extension unit's ACPI properties to confirm the presence
of these two amplifiers and if they exist add them manually onto the
SPI bus.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240416100904.3738093-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update the name for software node based SPI devices to use the fwnode
name as the device name. This is helpful since swnode devices are
usually added within the kernel, and the kernel often then requires a
predictable name such that it can refer back to the device.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240416100904.3738093-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use is_acpi_device_node() rather than checking ACPI_COMPANION(), such
that when checking for other types of firmware node, the code can
consistently do checks against the fwnode.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240416100904.3738093-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Due to the reading of FIFO during the dump of data registers in
debugfs, if SPI transmission is in progress, it will be affected
and may result in transmission failure. Therefore, the dump
interface of data registers in debugfs is removed.
Fixes: 2b2142f247eb ("spi: hisi-kunpeng: Add debugfs support")
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Reviewed-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/20240416015839.3323398-1-liudingyuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For some reason the commit 1209c5566f9b ("spi: Consistently use BIT
for cs_index_mask") missed one place to change, do it here to finish
the job.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240415184757.1198149-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In order of deduplication and better maintenance introduce a new
spi_for_each_valid_cs() helper macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240415193340.1279360-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The multi-CS support splits the comment and the code in the spi_set_cs().
To avoid this in the future extract spi_toggle_csgpiod() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240415193340.1279360-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is no need to allocate chip_data and then validate number of
CS pins as it will have the same effect. Hence move number of CS pins
validation out of condition in setup().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240403171550.1074644-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ID table already has respective entry and MODULE_DEVICE_TABLE and
creates proper alias for platform driver. Having another MODULE_ALIAS
causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240414154859.126931-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The version format string in the AXI SPI Engine driver was probably
intended to print the version number in the same format as the DT
compatible string (e.g. 1.00.a). However, the version just uses
semantic versioning so formatting the patch number as a character
is not correct and would result in printing control characters for
patch numbers less than 32.
Fixes: b1353d1c1d45 ("spi: Add Analog Devices AXI SPI Engine controller support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240412-axi-spi-engine-version-printf-v1-1-95e1e842c1a6@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Refactor code for "is the node's child available?" check by using the
corresponding macro instead, which reads more clearly.
While at it, use scope-based cleanup instead of manual of_node_put()
calls when getting platform data through cdns_xspi_of_get_plat_data().
This removes the unnecessary "node_child" declaration out of the loop's
scope and auto cleans up "node_child" when it goes out of scope, even
when we return early due to error.
Signed-off-by: Kousik Sanagavarapu <five231003@gmail.com>
Link: https://msgid.link/r/20240410130205.179069-1-five231003@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
cqspi_enable_dtr() is called for each operation, commands or not, reads
or writes. It writes CQSPI_REG_CONFIG then waits for idle (three
successful reads). Skip that in the no-DTR case if DTR is already
disabled.
It cannot be skipped in the DTR case as cqspi_setup_opcode_ext() writes
to a register and we must wait for idle state.
According to ftrace, the average cqspi_exec_mem_op() call goes from
85.4µs to 83.6µs when reading 235M over UBIFS on an octal flash.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240405-cdns-qspi-mbly-v2-6-956679866d6d@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Avoid of_device_get_match_data() call on each IRQ and each read
operation. Store pointer in `struct cqspi_st` device instance.
End-to-end performance measurements improve with this patch. On a given
octal flash, reading 235M over UBIFS is ~3.4% faster. During that read,
the average cqspi_exec_mem_op() call goes from 85.4µs to 80.7µs
according to ftrace. The worst case goes from 622.4µs to 615.2µs.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240405-cdns-qspi-mbly-v2-4-956679866d6d@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Cadence QSPI Controller driver is used on Mobileye EyeQ5 platform.
Allow building on MIPS.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240405-cdns-qspi-mbly-v2-3-956679866d6d@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In function pci1xxxx_spi_probe, there is a potential null pointer that
may be caused by a failed memory allocation by the function devm_kzalloc.
Hence, a null pointer check needs to be added to prevent null pointer
dereferencing later in the code.
To fix this issue, spi_bus->spi_int[iter] should be checked. The memory
allocated by devm_kzalloc will be automatically released, so just directly
return -ENOMEM without worrying about memory leaks.
Fixes: 1cc0cbea7167 ("spi: microchip: pci1xxxx: Add driver for SPI controller of PCI1XXXX PCIe switch")
Signed-off-by: Huai-Yuan Liu <qq810974084@gmail.com>
Link: https://msgid.link/r/20240403014221.969801-1-qq810974084@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
devm_spi_alloc_controller will allocate an SPI controller and
automatically release a reference on it when dev is unbound from
its driver. It doesn't need to call spi_controller_put explicitly
to put the reference when lpspi driver failed initialization.
Fixes: 2ae0ab0143fc ("spi: lpspi: Avoid potential use-after-free in probe()")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://msgid.link/r/20240403084029.2000544-1-carlos.song@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
pxa_ssp_request() implies a reference counting, hence the pxa_ssp_free()
must be called when we are done. Add missed call.
Fixes: bb77c99ee6d3 ("spi: pxa2xx: Skip SSP initialization if it's done elsewhere")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240402144523.3402063-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the SPI data size is smaller than FIFO, it operates in PIO mode,
and if it is larger than FIFO size, it oerates in DMA mode.
If the SPI data size is equal to fifo, it operates in PIO mode and it is
separated to 2 transfers. To prevent it, it must operate in DMA mode
from the case where the data size and the fifo size are the same.
Fixes: 1ee806718d5e ("spi: s3c64xx: support interrupt based pio mode")
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240329085840.65856-1-jaewon02.kim@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from David Lechner <dlechner@baylibre.com>:
I found a couple more controller drivers that were checking if the
tx_buf and rx_buf fields in the spi_transfer structure were set by a
peripheral driver that I missed in [1]. These checks can be removed
as well.
[1]: https://lore.kernel.org/linux-spi/20240325-spi-remove-is_dma_mapped-v2-1-d08d62b61f1c@baylibre.com/
|
|
Merge series from Louis Chauvet <louis.chauvet@bootlin.com>:
This series adds the support for the omap-mcspi multi mode which allows
sending SPI messages with a shorter delay between CS and the message.
One drawback of the multi-mode is that the CS is raised between each word,
so it can only be used with messages containing 1 word transfers and
asking for cs_change. Few devices, like FPGAs, may easily workaround this
limitation.
The first patch removes the current implementation, which is working, but
don't comply with what is asked in the spi transfer (The CS is raised by
the hardware regardless of cs_change state). No drivers or board file use this
implementation upstream.
The second patch adds the implementation of the multi-mode, which complies
with what is asked in the SPI message.
The third patch is the suggested optimization for using MULTI mode in more
situations.
|
|
There are no more peripheral drivers that set t->tx_dma or t->rx_dma.
Therefore, is_dma_mapped is always false and can be removed.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240328-spi-more-tx-rx-buf-cleanup-v1-2-9ec1ceedf08c@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
