| Age | Commit message (Collapse) | Author |
|---|
|
Add support for parsing DT time property "sink-bc12-completion-time-ms".
This timer is used to relax the PD state machine during Sink attach to
allow completion of Battery Charging (BC1.2) charger type detection in
TCPC before PD negotiations. BC1.2 detection is a hardware mechanism to
detect charger port type that is run by some controllers (such as
"maxim,max33359") in parallel to Type-C connection state machines.
This is to ensure that BC1.2 completes before PD is enabled as running
BC1.2 in parallel with PD negotiation results in delays violating timer
constraints in PD spec.
This is an optional timer and will not add any delay unless explicitly
set.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241103034402.2460252-4-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that we track TRBs base on request->num_trbs on reclaim, we don't
need to save the dwc3_request->needs_extra_trb check. Remove it.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/08dd88a3308ac7894267c52340eaf0e1564bbf36.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current logic in dwc3 driver is tracking req->num_queued_sgs and
req->sg. But they can be checked base on the num_pending_sgs and
num_trbs. They are redundant and can complicate the SG logic. Let's
remove them.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/96c7bf8f6b3e91e607d5b78ea51cb1d00c614eaf.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dwc3_request->num_queued_sgs is decremented on completion. If a
partially completed request is handled, then the
dwc3_request->num_queued_sgs no longer reflects the total number of
num_queued_sgs (it would be cleared).
Correctly check the number of request SG entries remained to be prepare
and queued. Failure to do this may cause null pointer dereference when
accessing non-existent SG entry.
Cc: stable@vger.kernel.org
Fixes: c96e6725db9d ("usb: dwc3: gadget: Correct the logic for queuing sgs")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d07a7c4aa0fcf746cdca0515150dbe5c52000af7.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The check whether the TRB ring is full or empty in dwc3_calc_trbs_left()
is insufficient. It assumes there are active TRBs if there's any request
in the started_list. However, that's not the case for requests with a
large SG list.
That is, if we have a single usb request that requires more TRBs than
the total TRBs in the TRB ring, the queued TRBs will be available when
all the TRBs in the ring are completed. But the request is only
partially completed and remains in the started_list. With the current
logic, the TRB ring is empty, but dwc3_calc_trbs_left() returns 0.
Fix this by additionally checking for the request->num_trbs for active
TRB count.
Cc: stable@vger.kernel.org
Fixes: 51f1954ad853 ("usb: dwc3: gadget: Fix dwc3_calc_trbs_left()")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/708dc62b56b77da1f704cc2ae9b6ddb1f2dbef1f.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver cannot issue the End Transfer command to the SETUP transfer.
Don't clear DWC3_EP_TRANSFER_STARTED flag to make sure that the driver
won't send Start Transfer command again, which can cause no-resource
error. For example this can occur if the host issues a reset to the
device.
Cc: stable@vger.kernel.org
Fixes: 76cb323f80ac ("usb: dwc3: ep0: clear all EP0 flags")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d3d618185fd614bb7426352a9fc1199641d3b5f5.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit ec6ce7075ef879b91a8710829016005dc8170f17.
Fix installation of WinUSB driver using OS descriptors. Without the
fix the drivers are not installed correctly and the property
'DeviceInterfaceGUID' is missing on host side.
The original change was based on the assumption that the interface
number is in the high byte of wValue but it is in the low byte,
instead. Unfortunately, the fix is based on MS documentation which is
also wrong.
The actual USB request for OS descriptors (using USB analyzer) looks
like:
Offset 0 1 2 3 4 5 6 7
0x000 C1 A1 02 00 05 00 0A 00
C1: bmRequestType (device to host, vendor, interface)
A1: nas magic number
0002: wValue (2: nas interface)
0005: wIndex (5: get extended property i.e. nas interface GUID)
008E: wLength (142)
The fix was tested on Windows 10 and Windows 11.
Cc: stable@vger.kernel.org
Fixes: ec6ce7075ef8 ("usb: gadget: composite: fix OS descriptors w_value logic")
Signed-off-by: Michal Vrastil <michal.vrastil@hidglobal.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Peter korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20241113235433.20244-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the clock sehci->clk was not enabled in spear_ehci_hcd_drv_probe,
it should not be disabled in any path.
Conversely, if it was enabled in spear_ehci_hcd_drv_probe, it must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 7675d6ba436f ("USB: EHCI: make ehci-spear a separate driver")
Cc: stable@vger.kernel.org
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241114230310.432213-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 6.13-rc1
Here are the USB-serial updates for 6.13-rc1, including:
- improved support for quirky pl2303 hxd devices
- make sure ftdi_sio TIOCGSERIAL returns consistent data
Everything has been in linux-next with no reported issues.
* tag 'usb-serial-6.13-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: Fix atomicity violation in get_serial_info()
USB: serial: pl2303: account for deficits of clones
|
|
Turns out that we have some const pointers being passed to
to_usb_device_driver() but were not catching this. Change the macro to
properly propagate the const-ness of the pointer so that we will notice
when we try to write to memory that we shouldn't be writing to.
This requires fixing up the usb_driver_applicable() function as well,
because it can handle a const * to struct usb_driver.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111342-lagoon-reapprove-5e49@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Turns out that we have some const pointers being passed to
to_usb_driver() but were not catching this. Change the macro to
properly propagate the const-ness of the pointer so that we will notice
when we try to write to memory that we shouldn't be writing to.
This requires fixing up the usb_match_dynamic_id() function as well,
because it can handle a const * to struct usb_driver.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111339-shaky-goldsmith-b233@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When walking the list of dynamic ids for a driver, no lock was being
held, which meant that an id could be removed or added while the list
was being iterated. Fix this up by properly grabing the lock while we
walk the list.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111324-tubby-facecloth-d4a0@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are a number of places where we accidentally pass in a constant
structure to later cast it off to a dynamic one, and then attempt to
grab a lock on it, which is not a good idea. To help resolve this, move
the dynamic id lock out of the dynamic id structure for the driver and
into one single lock for all USB dynamic ids. As this lock should never
have any real contention (it's only every accessed when a device is
added or removed, which is always serialized) there should not be any
difference except for some memory savings.
Note, this just converts the existing use of the dynamic id lock to the
new static lock, there is one place that is accessing the dynamic id
list without grabbing the lock, that will be fixed up in a follow-on
change.
Cc: Johan Hovold <johan@kernel.org>
Cc: Herve Codina <herve.codina@bootlin.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111322-kindly-finalist-d247@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure type safety by using min_t() instead of casted min().
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-9-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure type safety by using min_t() instead of casted min().
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-8-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure type safety by using min_t()/max_t() instead of casted min()/max().
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-7-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure type safety by using min_t() instead of casted min().
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-6-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure type safety by using min_t() instead of min().
Also add the explicit `unsigned int` as scripts/checkpatch.pl warns about:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-5-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure type safety by using min_t/max_t instead of casted min/max.
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-4-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure type safety by using max_t() instead of max().
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-3-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure type safety by using min_t() instead of casted min().
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-2-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are a few places in the kernel where PCI IDs for different Cadence
USB controllers are being used. Besides different naming, they duplicate
each other. Make this all in order by providing common definitions via
PCI IDs database and use in all users. While doing that, rename
definitions as Roger suggested.
Suggested-by: Roger Quadros <rogerq@kernel.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20241112160125.2340972-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently if the maximum-speed is set to Super Speed for a 3.1 Gen2
capable controller, the FORCE_GEN1 bit of LLUCTL register is set only
for one SuperSpeed port (or the first port) present. Modify the logic
to set the FORCE_GEN1 bit for all ports if speed is being limited to
Gen-1.
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241112182018.199392-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
logic
The existing implementation of the TxFIFO resizing logic only supports
scenarios where more than one port RAM is used. However, there is a need
to resize the TxFIFO in USB2.0-only mode where only a single port RAM is
available. This commit introduces the necessary changes to support
TxFIFO resizing in such scenarios by adding a missing check for single
port RAM.
This fix addresses certain platform configurations where the existing
TxFIFO resizing logic does not work properly due to the absence of
support for single port RAM. By adding this missing check, we ensure
that the TxFIFO resizing logic works correctly in all scenarios,
including those with a single port RAM.
Fixes: 9f607a309fbe ("usb: dwc3: Resize TX FIFOs to meet EP bursting requirements")
Cc: stable@vger.kernel.org # 6.12.x: fad16c82: usb: dwc3: gadget: Refine the logic for resizing Tx FIFOs
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241112044807.623-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since len1 is unsigned int, len1 < 0 always false. Remove it keep code
simple.
Signed-off-by: Rex Nie <rex.nie@jaguarmicro.com>
Rule: add
Link: https://lore.kernel.org/stable/20241108094255.2133-1-rex.nie%40jaguarmicro.com
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241112152021.2236-1-rex.nie@jaguarmicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "command" variable can be controlled by the user via debugfs. The
worry is that if con_index is zero then "&uc->ucsi->connector[con_index
- 1]" would be an array underflow.
Fixes: 170a6726d0e2 ("usb: typec: ucsi: add support for separate DP altmode devices")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/c69ef0b3-61b0-4dde-98dd-97b97f81d912@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some Lenovo platforms, the patch works around problems with ov2740
sensor initialization, which manifest themself like below:
[ 4.540476] ov2740 i2c-INT3474:01: error -EIO: failed to find sensor
[ 4.542066] ov2740 i2c-INT3474:01: probe with driver ov2740 failed with error -5
or
[ 7.742633] ov2740 i2c-INT3474:01: chip id mismatch: 2740 != 0
[ 7.742638] ov2740 i2c-INT3474:01: error -ENXIO: failed to find sensor
and also by random failures of video stream start.
Issue can be reproduced by this script:
n=0
k=0
while [ $n -lt 50 ] ; do
sudo modprobe -r ov2740
sleep `expr $RANDOM % 5`
sudo modprobe ov2740
if media-ctl -p | grep -q ov2740 ; then
let k++
fi
let n++
done
echo Success rate $k/$n
Without the patch, success rate is approximately 15 or 50 tries.
With the patch it does not fail.
This problem is some hardware or firmware malfunction, that can not be
easy debug and fix. While setting small autosuspend delay is not perfect
workaround as user can configure it to any value, it will prevent
the failures by default.
Additionally setting small autosuspend delay should have positive effect
on power consumption as for most ljca workloads device is used for just
a few milliseconds flowed by long periods of at least 100ms of inactivity
(usually more).
Fixes: acd6199f195d ("usb: Add support for Intel LJCA device")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com> # ThinkPad X1 Yoga Gen 8, ov2740
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://lore.kernel.org/r/20241112075514.680712-2-stanislaw.gruszka@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do not mark interface as ready to suspend when we are still waiting
for response messages from the device.
Fixes: acd6199f195d ("usb: Add support for Intel LJCA device")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com> # ThinkPad X1 Yoga Gen 8, ov2740
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://lore.kernel.org/r/20241112075514.680712-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dtbinding have imx7ulp and imx8ulp compatible with imx7d before. And
then the dtb follow the dtbinding. However, the driver doesn't add imx8ulp
compatible now. To make imx8ulp work well, this will add support for it.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20241111090916.1534047-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The GET_CAPABILITY size is wrong. The definitions for the
command sizes are for bitfieds and therefore in bits, not
bytes.
This fixes an issue that prevents the interface from being
registered with UCSI versions older than 2.0 because the
command size exceeds the MESSAGE_IN field size.
Fixes: 226ff2e681d0 ("usb: typec: ucsi: Convert connector specific commands to bitmaps")
Reported-by: Abel Vesa <abel.vesa@linaro.org>
Closes: https://lore.kernel.org/linux-usb/Zy864W7sysWZbCTd@linaro.org/
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241111100220.1743872-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a possibility that a request's callback could be invoked from
usb_ep_queue() (call trace below, supplemented with missing calls):
req->complete from usb_gadget_giveback_request
(drivers/usb/gadget/udc/core.c:999)
usb_gadget_giveback_request from musb_g_giveback
(drivers/usb/musb/musb_gadget.c:147)
musb_g_giveback from rxstate
(drivers/usb/musb/musb_gadget.c:784)
rxstate from musb_ep_restart
(drivers/usb/musb/musb_gadget.c:1169)
musb_ep_restart from musb_ep_restart_resume_work
(drivers/usb/musb/musb_gadget.c:1176)
musb_ep_restart_resume_work from musb_queue_resume_work
(drivers/usb/musb/musb_core.c:2279)
musb_queue_resume_work from musb_gadget_queue
(drivers/usb/musb/musb_gadget.c:1241)
musb_gadget_queue from usb_ep_queue
(drivers/usb/gadget/udc/core.c:300)
According to the docstring of usb_ep_queue(), this should not happen:
"Note that @req's ->complete() callback must never be called from within
usb_ep_queue() as that can create deadlock situations."
In fact, a hardware lockup might occur in the following sequence:
1. The gadget is initialized using musb_gadget_enable().
2. Meanwhile, a packet arrives, and the RXPKTRDY flag is set, raising an
interrupt.
3. If IRQs are enabled, the interrupt is handled, but musb_g_rx() finds an
empty queue (next_request() returns NULL). The interrupt flag has
already been cleared by the glue layer handler, but the RXPKTRDY flag
remains set.
4. The first request is enqueued using usb_ep_queue(), leading to the call
of req->complete(), as shown in the call trace above.
5. If the callback enables IRQs and another packet is waiting, step (3)
repeats. The request queue is empty because usb_g_giveback() removes the
request before invoking the callback.
6. The endpoint remains locked up, as the interrupt triggered by hardware
setting the RXPKTRDY flag has been handled, but the flag itself remains
set.
For this scenario to occur, it is only necessary for IRQs to be enabled at
some point during the complete callback. This happens with the USB Ethernet
gadget, whose rx_complete() callback calls netif_rx(). If called in the
task context, netif_rx() disables the bottom halves (BHs). When the BHs are
re-enabled, IRQs are also enabled to allow soft IRQs to be processed. The
gadget itself is initialized at module load (or at boot if built-in), but
the first request is enqueued when the network interface is brought up,
triggering rx_complete() in the task context via ioctl(). If a packet
arrives while the interface is down, it can prevent the interface from
receiving any further packets from the USB host.
The situation is quite complicated with many parties involved. This
particular issue can be resolved in several possible ways:
1. Ensure that callbacks never enable IRQs. This would be difficult to
enforce, as discovering how netif_rx() interacts with interrupts was
already quite challenging and u_ether is not the only function driver.
Similar "bugs" could be hidden in other drivers as well.
2. Disable MUSB interrupts in musb_g_giveback() before calling the callback
and re-enable them afterwars (by calling musb_{dis,en}able_interrupts(),
for example). This would ensure that MUSB interrupts are not handled
during the callback, even if IRQs are enabled. In fact, it would allow
IRQs to be enabled when releasing the lock. However, this feels like an
inelegant hack.
3. Modify the interrupt handler to clear the RXPKTRDY flag if the request
queue is empty. While this approach also feels like a hack, it wastes
CPU time by attempting to handle incoming packets when the software is
not ready to process them.
4. Flush the Rx FIFO instead of calling rxstate() in musb_ep_restart().
This ensures that the hardware can receive packets when there is at
least one request in the queue. Once IRQs are enabled, the interrupt
handler will be able to correctly process the next incoming packet
(eventually calling rxstate()). This approach may cause one or two
packets to be dropped (two if double buffering is enabled), but this
seems to be a minor issue, as packet loss can occur when the software is
not yet ready to process them. Additionally, this solution makes the
gadget driver compliant with the rule mentioned in the docstring of
usb_ep_queue().
There may be additional solutions, but from these four, the last one has
been chosen as it seems to be the most appropriate, as it addresses the
"bad" behavior of the driver.
Fixes: baebdf48c360 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
Cc: stable@vger.kernel.org
Signed-off-by: Hubert Wiśniewski <hubert.wisniewski.25632@gmail.com>
Link: https://lore.kernel.org/r/4ee1ead4525f78fb5909a8cbf99513ad0082ad21.camel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of checking if any of the USB-C ports have orientation GPIO and
thus is orientation-aware, check for the GPIO for the port being
registered. There are no boards that are affected by this change at this
moment, so the patch is not marked as a fix, but it might affect other
boards in future.
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241109-ucsi-glue-fixes-v2-2-8b21ff4f9fbe@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UCSI connector's indices start from 1 up to 3, PMIC_GLINK_MAX_PORTS.
Correct the condition in the pmic_glink_ucsi_connector_status()
callback, fixing Type-C orientation reporting for the third USB-C
connector.
Fixes: 76716fd5bf09 ("usb: typec: ucsi: glink: move GPIO reading into connector_status callback")
Cc: stable@vger.kernel.org
Reported-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241109-ucsi-glue-fixes-v2-1-8b21ff4f9fbe@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After an initial range change on the insigned int alt being > 1
the only possible values for alt are 0 or 1. Therefore the else
statement for values other than 0 or 1 is redundant and can be
removed. Replace the else if (all == 1) check with just an else.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/5f54ffd0-b5fe-4203-a626-c166becad362@gmail.com
Link: https://lore.kernel.org/r/20241107133348.22762-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Avoid using GPIOF_ACTIVE_LOW as it's deprecated and subject to remove.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241104093609.156059-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 6.12-rc7
Here's a fix for a long-standing use-after-free in an io_edgeport debug
printk and some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.12-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add support for Sierra Wireless EM86xx
USB: serial: io_edgeport: fix use after free in debug printk
USB: serial: option: add Quectel RG650V
USB: serial: option: add Fibocom FG132 0x0112 composition
|
|
Our static checker found a bug where set_serial_info() uses a mutex, but
get_serial_info() does not. Fortunately, the impact of this is relatively
minor. It doesn't cause a crash or any other serious issues. However, if a
race condition occurs between set_serial_info() and get_serial_info(),
there is a chance that the data returned by get_serial_info() will be
inconsistent.
Fixes: 3ae36bed3a93 ("fdti_sio: switch to ->[sg]et_serial()")
Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
That allows the fields in those command data structures to
be easily validated. If an unsupported field is accessed, a
warning is generated.
This will not force UCSI version checks to be made in every
place where these data structures are accessed, but it will
make it easier to pinpoint issues that are caused by the
unconditional accesses to those fields, and perhaps more
importantly, allow those issues to be noticed immediately.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241106150605.1017744-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are apparently incomplete clones of the HXD type chip in use.
Those return -EPIPE on GET_LINE_REQUEST and BREAK_REQUEST. Avoid
flooding the kernel log with those errors. Detect them during startup
and then use the line_settings cache instead of GET_LINE_REQUEST. Signal
missing break support via -ENOTTY.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
[ johan: fix macro prefix, drop oom error message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add support for Sierra Wireless EM86xx with USB-id 0x1199:0x90e5 and
0x1199:0x90e4.
0x1199:0x90e5
T: Bus=03 Lev=01 Prnt=01 Port=05 Cnt=01 Dev#= 14 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1199 ProdID=90e5 Rev= 5.15
S: Manufacturer=Sierra Wireless, Incorporated
S: Product=Semtech EM8695 Mobile Broadband Adapter
S: SerialNumber=004403161882339
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#=12 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=qcserial
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=qcserial
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I:* If#=12 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#=13 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#=13 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x1199:0x90e4
T: Bus=03 Lev=01 Prnt=01 Port=05 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1199 ProdID=90e4 Rev= 0.00
S: Manufacturer=Sierra Wireless, Incorporated
S: SerialNumber=004403161882339
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=10 Driver=qcserial
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Jack Wu <wojackbb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Stop Endpoint command on an already stopped endpoint fails and may be
misinterpreted as a known hardware bug by the completion handler. This
results in an unnecessary delay with repeated retries of the command.
Avoid queuing this command when endpoint state flags indicate that it's
stopped or halted and the command will fail. If commands are pending on
the endpoint, their completion handlers will process cancelled TDs so
it's done. In case of waiting for external operations like clearing TT
buffer, the endpoint is stopped and cancelled TDs can be processed now.
This eliminates practically all unnecessary retries because an endpoint
with pending URBs is maintained in Running state by the driver, unless
aforementioned commands or other operations are pending on it. This is
guaranteed by xhci_ring_ep_doorbell() and by the fact that it is called
every time any of those operations completes.
The only known exceptions are hardware bugs (the endpoint never starts
at all) and Stream Protocol errors not associated with any TRB, which
cause an endpoint reset not followed by restart. Sounds like a bug.
Generally, these retries are only expected to happen when the endpoint
fails to start for unknown/no reason, which is a worse problem itself,
and fixing the bug eliminates the retries too.
All cases were tested and found to work as expected. SET_DEQ_PENDING
was produced by patching uvcvideo to unlink URBs in 100us intervals,
which then runs into this case very often. EP_HALTED was produced by
restarting 'cat /dev/ttyUSB0' on a serial dongle with broken cable.
EP_CLEARING_TT by the same, with the dongle on an external hub.
Fixes: fd9d55d190c0 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-34-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_invalidate_cancelled_tds() may not work correctly if the hardware
is modifying endpoint or stream contexts at the same time by executing
a Set TR Dequeue command. And even if it worked, it would be unable to
queue Set TR Dequeue for the next stream, failing to clear xHC cache.
On stream endpoints, a chain of Set TR Dequeue commands may take some
time to execute and we may want to cancel more TDs during this time.
Currently this leads to Stop Endpoint completion handler calling this
function without testing for SET_DEQ_PENDING, which will trigger the
aforementioned problems when it happens.
On all endpoints, a halt condition causes Reset Endpoint to be queued
and an error status given to the class driver, which may unlink more
URBs in response. Stop Endpoint is queued and its handler may execute
concurrently with Set TR Dequeue queued by Reset Endpoint handler.
(Reset Endpoint handler calls this function too, but there seems to
be no possibility of it running concurrently with Set TR Dequeue).
Fix xhci_invalidate_cancelled_tds() to work correctly under a pending
Set TR Dequeue. Bail out of the function when SET_DEQ_PENDING is set,
then make the completion handler call the function again and also call
xhci_giveback_invalidated_tds(), which needs to be called next.
This seems to fix another potential bug, where the handler would call
xhci_invalidate_cancelled_tds(), which may clear some deferred TDs if
a sanity check fails, and the TDs wouldn't be given back promptly.
Said sanity check seems to be wrong and prone to false positives when
the endpoint halts, but fixing it is beyond the scope of this change,
besides ensuring that cleared TDs are given back properly.
Fixes: 5ceac4402f5d ("xhci: Handle TD clearing for multiple streams case")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-33-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some host controllers fail to atomically transition an endpoint to the
Running state on a doorbell ring and enter a hidden "Restarting" state,
which looks very much like Stopped, with the important difference that
it will spontaneously transition to Running anytime soon.
A Stop Endpoint command queued in the Restarting state typically fails
with Context State Error and the completion handler sees the Endpoint
Context State as either still Stopped or already Running. Even a case
of Halted was observed, when an error occurred right after the restart.
The Halted state is already recovered from by resetting the endpoint.
The Running state is handled by retrying Stop Endpoint.
The Stopped state was recognized as a problem on NEC controllers and
worked around also by retrying, because the endpoint soon restarts and
then stops for good. But there is a risk: the command may fail if the
endpoint is "stopped for good" already, and retries will fail forever.
The possibility of this was not realized at the time, but a number of
cases were discovered later and reproduced. Some proved difficult to
deal with, and it is outright impossible to predict if an endpoint may
fail to ever start at all due to a hardware bug. One such bug (albeit
on ASM3142, not on NEC) was found to be reliably triggered simply by
toggling an AX88179 NIC up/down in a tight loop for a few seconds.
An endless retries storm is quite nasty. Besides putting needless load
on the xHC and CPU, it causes URBs never to be given back, paralyzing
the device and connection/disconnection logic for the whole bus if the
device is unplugged. User processes waiting for URBs become unkillable,
drivers and kworker threads lock up and xhci_hcd cannot be reloaded.
For peace of mind, impose a timeout on Stop Endpoint retries in this
case. If they don't succeed in 100ms, consider the endpoint stopped
permanently for some reason and just give back the unlinked URBs. This
failure case is rare already and work is under way to make it rarer.
Start this work today by also handling one simple case of race with
Reset Endpoint, because it costs just two lines to implement.
Fixes: fd9d55d190c0 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-32-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code which it is referencing does not exist in the same function,
or the file for that matter. Since it was added [1], the Interrupter
Moderation Interval can be changed within xhci addon, e.g. PCI
xhci_pci_setup().
[1], commit 0ebbab374223 ("USB: xhci: Ring allocation and initialization.")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-31-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add xhci_dequeue_td() helper function to reduce code duplication.
Function xhci_dequeue_td() advances the dequeue pointer past the specified
Transfer Descriptor (TD) and releases the TD.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-30-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The function is modified to return 'void' instead of an integer since it
invariably returns '0'. Additionally, multiple functions which only
return xhci_td_cleanup() are also refactored to return void.
This change eliminates the need for callers to handle a return value that
does not convey meaningful information and improve code readability, as it
becomes immediately clear that the function does not produce a significant
output.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-29-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Function td_to_noop() does not utilize arguments 'xhci' and 'ep_ring'.
These unused arguments are removed to clean up the code.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-28-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove redundant TRB cycle reset, the TRB cycle is already set to zero by
the preceding memset(), making the explicit reset unnecessary.
Clarify ring loop start point. Change the loop start from the dequeue
segment to the start segment. Both approaches achieve the same result,
but starting from the start segment makes it clearer that the entire ring
is being zeroed out.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-27-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Variable 'max_interrupters' contains the maximum supported interrupters
or the maximum interrupters the user has requested. Thus, it should be
used instead of HCS_MAX_INTRS().
User set 'max_interrupters' value is validated in xhci_gen_setup(),
otherwise 'max_interrupters' value is 'HCS_MAX_INTRS(xhci->hcs_params1)'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This quirk is old and seldom seen, as a result the trace is changed
to debug message and only printed when the quirk is set.
Move it into xhci_gen_setup() where the majority of quirks are set.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-25-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
