| Age | Commit message (Collapse) | Author |
|---|
|
Linux xHCI driver doesn't report and handle port cofig error change.
If Port Configure Error for root hub port occurs, CEC bit in PORTSC
would be set by xHC and remains 1. This happends when the root port
fails to configure its link partner, e.g. the port fails to exchange
port capabilities information using Port Capability LMPs.
Then the Port Status Change Events will be blocked until all status
change bits(CEC is one of the change bits) are cleared('0') (refer to
xHCI spec 4.19.2). Otherwise, the port status change event for this
root port will not be generated anymore, then root port would look
like dead for user and can't be recovered until a Host Controller
Reset(HCRST).
This patch is to check CEC bit in PORTSC in xhci_get_port_status()
and set a Config Error in the return status if CEC is set. This will
cause a ClearPortFeature request, where CEC bit is cleared in
xhci_clear_port_change_bit().
[The commit log is based on initial Marvell patch posted at
http://marc.info/?l=linux-kernel&m=142323612321434&w=2]
Reported-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v3.2+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'regulator/fix/palmas' into regulator-linus
|
|
Its ClickPad shares PNP ID "LEN2006" with the one in model E540 which is
already handled by the driver (both are Haswell iterations of the Edge
line, launched in 2014) but the dimensions it reports are different:
$ sudo ./touchpad-edge-detector /dev/input/event3
Touchpad SynPS/2 Synaptics TouchPad on /dev/input/event3
Move one finger around the touchpad to detect the actual edges
Kernel says: x [1472..5044], y [1408..3398]
Touchpad sends: x [1024..5045], y [2457..4832] /^C
Fortunately we can use the board ID, which is also different, to
distinguish among them.
$ dmesg | grep -i synaptics
psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1,
caps: 0xd001a3/0x940300/0x127c00, board id: 2691, fw id: 1494646
psmouse serio1: synaptics: serio: Synaptics pass-through port at
isa0060/serio1/input0
input: SynPS/2 Synaptics TouchPad as
/devices/platform/i8042/serio1/input/input4
Board ID in E540 is 2722:
psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1,
caps: 0xd001a3/0x940300/0x127c00, board id: 2722, fw id: 1484859
(from https://launchpadlibrarian.net/179702965/BootDmesg.txt)
Signed-off-by: Ramiro Morales <cramm0@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Pull networking fixes from David Miller:
1) Validate iov ranges before feeding them into iov_iter_init(), from
Al Viro.
2) We changed copy_from_msghdr_from_user() to zero out the msg_namelen
is a NULL pointer is given for the msg_name. Do the same in the
compat code too. From Catalin Marinas.
3) Fix partially initialized tuples in netfilter conntrack helper, from
Ian Wilson.
4) Missing continue; statement in nft_hash walker can lead to crashes,
from Herbert Xu.
5) tproxy_tg6_check looks for IP6T_INV_PROTO in ->flags instead of
->invflags, fix from Pablo Neira Ayuso.
6) Incorrect memory account of TCP FINs can result in negative socket
memory accounting values. Fix from Josh Hunt.
7) Don't allow virtual functions to enable VLAN promiscuous mode in
be2net driver, from Vasundhara Volam.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netfilter: nft_compat: set IP6T_F_PROTO flag if protocol is set
cx82310_eth: wait for firmware to become ready
net: validate the range we feed to iov_iter_init() in sys_sendto/sys_recvfrom
net: compat: Update get_compat_msghdr() to match copy_msghdr_from_user() behaviour
be2net: use PCI MMIO read instead of config read for errors
be2net: restrict MODIFY_EQ_DELAY cmd to a max of 8 EQs
be2net: Prevent VFs from enabling VLAN promiscuous mode
tcp: fix tcp fin memory accounting
ipv6: fix backtracking for throw routes
net: ethernet: pcnet32: Setup the SRAM and NOUFLO on Am79C97{3, 5}
ipv6: call ipv6_proxy_select_ident instead of ipv6_select_ident in udp6_ufo_fragment
netfilter: xt_TPROXY: fix invflags check in tproxy_tg6_check()
netfilter: restore rule tracing via nfnetlink_log
netfilter: nf_tables: allow to change chain policy without hook if it exists
netfilter: Fix potential crash in nft_hash walker
netfilter: Zero the tuple in nfnl_cthelper_parse_tuple()
|
|
Commit 3296f71cd2fde7a2ad52e66a27eae419f6328066 ("Input: ALPS - consolidate
setting protocol parameters") inadvertently moved call to
alps_dolphin_get_device_area() from v5 to v7 protocol, causing both
protocols report incorrect maximum values for X and Y axes which resulted
in crash in Synaptics X driver.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94801
Reported-by: Santiago Gala <sgala@apache.org>
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Driver recovery requires the device's list node to have been initialized.
Fixes: https://lkml.org/lkml/2015/3/22/262
Reported-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Commit 25b884a83d487fd62c3de7ac1ab5549979188482 ("x86/xen: set
regions above the end of RAM as 1:1") introduced a regression.
To be able to add memory pages which were added via memory hotplug to
a pv domain, the pages must be "invalid" instead of "identity" in the
p2m list before they can be added.
Suggested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org> # 3.16+
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Commit 054954eb051f35e74b75a566a96fe756015352c8 ("xen: switch to linear
virtual mapped sparse p2m list") introduced a regression regarding to
memory hotplug for a pv-domain: as the virtual space for the p2m list
is allocated for the to be expected memory size of the domain only,
hotplugged memory above that size will not be usable by the domain.
Correct this by using a configurable size for the p2m list in case of
memory hotplug enabled (default supported memory size is 512 GB for
64 bit domains and 4 GB for 32 bit domains).
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org> # 3.19+
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
The of_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Device domains never span IOMMU hardware units, which allows the
domain ID space for each IOMMU to be an independent address space.
Therefore we can have multiple, independent domains, each with the
same domain->id, but attached to different hardware units. This is
also why we need to do a heavy-weight search for VM domains since
they can span multiple IOMMUs hardware units and we don't require a
single global ID to use for all hardware units.
Therefore, if we call iommu_detach_domain() across all active IOMMU
hardware units for a non-VM domain, the result is that we clear domain
IDs that are not associated with our domain, allowing them to be
re-allocated and causing apparent coherency issues when the device
cannot access IOVAs for the intended domain.
This bug was introduced in commit fb170fb4c548 ("iommu/vt-d: Introduce
helper functions to make code symmetric for readability"), but is
significantly exacerbated by the more recent commit 62c22167dd70
("iommu/vt-d: Fix dmar_domain leak in iommu_attach_device") which calls
domain_exit() more frequently to resolve a domain leak.
Fixes: fb170fb4c548 ("iommu/vt-d: Introduce helper functions to make code symmetric for readability")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: stable@vger.kernel.org # v3.17+
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch is a fix to "iommu/arm-smmu: add support for iova_to_phys
through ATS1PR".
According to ARM documentation, translation registers are optional even
in SMMUv1, so ID0_S1TS needs to be checked to verify their presence.
Also, we check that the domain is a stage-1 domain.
Signed-off-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
user_mode_vm() and user_mode() are now the same. Change all callers
of user_mode_vm() to user_mode().
The next patch will remove the definition of user_mode_vm.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/43b1f57f3df70df5a08b0925897c660725015554.1426728647.git.luto@kernel.org
[ Merged to a more recent kernel. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* avoid panic with lots of IBSS stations
* Fix dvm's behavior after suspend resume
* Allow to keep connection after CSA failure
* Remove a noisy by harmless WARN_ON
* New device IDs
|
|
Pull bugfix for md from Neil Brown:
"One fix for md in 4.0-rc4
Regression in recent patch causes crash on error path"
* tag 'md/4.0-rc4-fix' of git://neil.brown.name/md:
md: fix problems with freeing private data after ->run failure.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are three fixes for 4.0-rc5 that revert 3 PCMCIA patches that
were merged in 4.0-rc1 that cause regressions. So let's revert them
for now and they will be reworked and resent sometime in the future.
All have been tested in linux-next for a while"
* tag 'char-misc-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "pcmcia: add a new resource manager for non ISA systems"
Revert "pcmcia: fix incorrect bracketing on a test"
Revert "pcmcia: add missing include for new pci resource handler"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are four small staging driver fixes, all for the vt6656 and
vt6655 drivers, that resolve some reported issues with them.
All of these patches have been in linux next for a while"
* tag 'staging-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
vt6655: Fix late setting of byRFType.
vt6655: RFbSetPower fix missing rate RATE_12M
staging: vt6656: vnt_rf_setpower: fix missing rate RATE_12M
staging: vt6655: vnt_tx_packet fix dma_idx selection.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fix from Greg KH:
"Here's a single 8250 serial driver that fixes a reported deadlock with
the serial console and the tty driver.
It's been in linux-next for a while now"
* tag 'tty-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_dw: Fix deadlock in LCR workaround
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY driver fixes from Greg KH:
"Here's a number of USB and PHY driver fixes for 4.0-rc5.
The largest thing here is a revert of a gadget function driver patch
that removes 500 lines of code. Other than that, it's a number of
reported bugs fixes and new quirk/id entries.
All have been in linux-next for a while"
* tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: common: otg-fsm: only signal connect after switching to peripheral
uas: Add US_FL_NO_ATA_1X for Initio Corporation controllers / devices
USB: ehci-atmel: rework clk handling
MAINTAINERS: add entry for USB OTG FSM
usb: chipidea: otg: add a_alt_hnp_support response for B device
phy: omap-usb2: Fix missing clk_prepare call when using old dt name
phy: ti/omap: Fix modalias
phy: core: Fixup return value of phy_exit when !pm_runtime_enabled
phy: miphy28lp: Convert to devm_kcalloc and fix wrong sizof
phy: miphy365x: Convert to devm_kcalloc and fix wrong sizeof
phy: twl4030-usb: Remove redundant assignment for twl->linkstat
phy: exynos5-usbdrd: Fix off-by-one valid value checking for args->args[0]
phy: Find the right match in devm_phy_destroy()
phy: rockchip-usb: Fixup rockchip_usb_phy_power_on failure path
phy: ti-pipe3: Simplify ti_pipe3_dpll_wait_lock implementation
phy: samsung-usb2: Remove NULL terminating entry from phys array
phy: hix5hd2-sata: Check return value of platform_get_resource
phy: exynos-dp-video: Kill exynos_dp_video_phy_pwr_isol function
Revert "usb: gadget: zero: Add support for interrupt EP"
Revert "xhci: Clear the host side toggle manually when endpoint is 'soft reset'"
...
|
|
Return EPROBE_DEFER if Regulator returns EPROBE_DEFER
If the Flexcan driver is built into kernel and a regulator is used to
enable the CAN transceiver, the Flexcan driver may not use the regulator.
When initializing the Flexcan device with a regulator defined in the device
tree, but not initialized, the regulator subsystem returns EPROBE_DEFER, hence
the Flexcan init fails.
The solution for this is to return EPROBE_DEFER if regulator is not initialized
and wait until the regulator is initialized.
Signed-off-by: Andreas Werner <kernel@andy89.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Making sure that the bus-off state gets passed to can_change_state().
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The PCAN USB (pro) FD adapters with firmware versions > 2.x support the
switching between ISO (default) and non-ISO conform bitstreams on the CAN bus.
The setting for the 2.x firmware adapters can be modified with the 'ip' tool
from the iproute2 package (option: fd-non-iso [on|off]).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The PUCAN_CMD_RX_FRAME_(ENABLE|DISABLE) command has extended its purpose
and was therefore renamed to PUCAN_CMD_SET_(EN|DIS)_OPTION.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
smatch detected the following issue:
drivers/net/can/usb/gs_usb.c:904 gs_usb_probe() error:
potential null dereference 'dev'. (kzalloc returns null)
Add a check for null return from kzalloc and return -ENOMEM
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
USB endpoint's wMaxPacketSize field is an le16 entity. Use
appropriate le16_to_cpu macros to maintain endian independence.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Current driver code arbitrarily assumes a max outstanding tx
value of 16 parallel transmissions. Meanwhile, the device
firmware provides its actual maximum inside its reply to the
CMD_GET_SOFTWARE_INFO message.
Under heavy tx traffic, if the interleaved transmissions count
increases above the limit reported by firmware, the firmware
breaks up badly, reports a massive list of internal errors, and
the candump traces hardly matches the actual frames sent and
received.
On the other hand, in certain models, the firmware can support
up to 48 tx URBs instead of just 16, increasing the driver
throughput by two-fold and reducing the possibility of -ENOBUFs.
Thus dynamically set the driver's max tx URBs value according
to firmware replies.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Transmission of an AP beacon does not call the TX interrupt service routine,
which usually does the cleanup. Instead, cleanup is handled in a tasklet
completion routine. Unfortunately, this routine has a serious bug in that it does
not release the DMA mapping before it frees the skb, thus one IOMMU mapping is
leaked for each beacon. The test system failed with no free IOMMU mapping slots
approximately one hour after hostapd was used to start an AP.
This issue was reported and tested at https://github.com/lwfinger/rtlwifi_new/issues/30.
Reported-and-tested-by: Kevin Mullican <kevin@mullican.com>
Cc: Kevin Mullican <kevin@mullican.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When the device is powered up, some (older) firmware versions fail to work
properly if we send commands before the boot is complete (everything is OK
when the device is hot-plugged). The firmware indicates its ready status by
putting the link up.
Newer firmwares delay the first command so they don't suffer from this problem.
They also report the link being always up.
Wait for firmware to become ready (link up) before sending any commands and/or
data.
This also allows lowering CMD_TIMEOUT value to a reasonable time.
Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull slave dmaengine fixes from Vinod Koul:
"Four fixes for dw, pl08x, imx-sdma and at_hdmac driver. Nothing
unusual here, simple fixes to these drivers"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: pl08x: Define capabilities for generic capabilities reporting
dmaengine: dw: append MODULE_ALIAS for platform driver
dmaengine: imx-sdma: switch to dynamic context mode after script loaded
dmaengine: at_hdmac: Fix calculation of the residual bytes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes for recent regressions (PCI/ACPI resources and at91
RTC locking), a stable-candidate powercap RAPL driver fix and two ARM
cpuidle fixes (one stable-candidate too).
Specifics:
- Revert a recent PCI commit related to IRQ resources management that
introduced a regression for drivers attempting to bind to devices
whose previous drivers did not balance pci_enable_device() and
pci_disable_device() as expected (Rafael J Wysocki).
- Fix a deadlock in at91_rtc_interrupt() introduced by a typo in a
recent commit related to wakeup interrupt handling (Dan Carpenter).
- Allow the power capping RAPL (Running-Average Power Limit) driver
to use different energy units for domains within one CPU package
which is necessary to handle Intel Haswell EP processors correctly
(Jacob Pan).
- Improve the cpuidle mvebu driver's handling of Armada XP SoCs by
updating the target residency and exit latency numbers for those
chips (Sebastien Rannou).
- Prevent the cpuidle mvebu driver from calling cpu_pm_enter() twice
in a row before cpu_pm_exit() is called on the same CPU which
breaks the core's assumptions regarding the usage of those
functions (Gregory Clement)"
* tag 'pm+acpi-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "x86/PCI: Refine the way to release PCI IRQ resources"
rtc: at91rm9200: double locking bug in at91_rtc_interrupt()
powercap / RAPL: handle domains with different energy units
cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
cpuidle: mvebu: Fix the CPU PM notifier usage
|
|
Pull drm updates from Dave Airlie:
"A bunch of fixes across drivers:
radeon:
disable two ended allocation for now, it breaks some stuff
amdkfd:
misc fixes
nouveau:
fix irq loop problem, add basic support for GM206 (new hw)
i915:
fix some WARNs people were seeing
exynos:
fix some iommu interactions causing boot failures"
* git://people.freedesktop.org/~airlied/linux:
drm/radeon: drop ttm two ended allocation
drm/exynos: fix the initialization order in FIMD
drm/exynos: fix typo config name correctly.
drm/exynos: Check for NULL dereference of crtc
drm/exynos: IS_ERR() vs NULL bug
drm/exynos: remove unused files
drm/i915: Make sure the primary plane is enabled before reading out the fb state
drm/nouveau/bios: fix i2c table parsing for dcb 4.1
drm/nouveau/device/gm100: Basic GM206 bring up (as copy of GM204)
drm/nouveau/device: post write to NV_PMC_BOOT_1 when flipping endian switch
drm/nouveau/gr/gf100: fix some accidental or'ing of buffer addresses
drm/nouveau/fifo/nv04: remove the loop from the interrupt handler
drm/radeon: Changing number of compute pipe lines
drm/amdkfd: Fix SDMA queue init. in non-HWS mode
drm/amdkfd: destroy mqd when destroying kernel queue
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull more DeviceTree fixes vfom Rob Herring:
- revert setting stdout-path as preferred console. This caused
regressions in PowerMACs and other systems.
- yet another fix for stdout-path option parsing.
- fix error path handling in of_irq_parse_one
* tag 'devicetree-fixes-for-4.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Revert "of: Fix premature bootconsole disable with 'stdout-path'"
of: handle both '/' and ':' in path strings
of: unittest: Add option string test case with longer path
of/irq: Fix of_irq_parse_one() returned error codes
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Here are current target-pending fixes for v4.0-rc5 code that have made
their way into the queue over the last weeks.
The fixes this round include:
- Fix long-standing iser-target logout bug related to early
conn_logout_comp completion, resulting in iscsi_conn use-after-tree
OOpsen. (Sagi + nab)
- Fix long-standing tcm_fc bug in ft_invl_hw_context() failure
handing for DDP hw offload. (DanC)
- Fix incorrect use of unprotected __transport_register_session() in
tcm_qla2xxx + other single local se_node_acl fabrics. (Bart)
- Fix reference leak in target_submit_cmd() -> target_get_sess_cmd()
for ack_kref=1 failure path. (Bart)
- Fix pSCSI backend ->get_device_type() statistics OOPs with
un-configured device. (Olaf + nab)
- Fix virtual LUN=0 target_configure_device failure OOPs at modprobe
time. (Claudio + nab)
- Fix FUA write false positive failure regression in v4.0-rc1 code.
(Christophe Vu-Brugier + HCH)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: do not reject FUA CDBs when write cache is enabled but emulate_write_cache is 0
target: Fix virtual LUN=0 target_configure_device failure OOPs
target/pscsi: Fix NULL pointer dereference in get_device_type
tcm_fc: missing curly braces in ft_invl_hw_context()
target: Fix reference leak in target_get_sess_cmd() error path
loop/usb/vhost-scsi/xen-scsiback: Fix use of __transport_register_session
tcm_qla2xxx: Fix incorrect use of __transport_register_session
iscsi-target: Avoid early conn_logout_comp for iser connections
Revert "iscsi-target: Avoid IN_LOGOUT failure case for iser-target"
target: Disallow changing of WRITE cache/FUA attrs after export
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull devicemapper fixes from Mike Snitzer:
"A handful of stable fixes for DM:
- fix thin target to always zero-fill reads to unprovisioned blocks
- fix to interlock device destruction's suspend from internal
suspends
- fix 2 snapshot exception store handover bugs
- fix dm-io to cope with DISCARD and WRITE_SAME capabilities changing"
* tag 'dm-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm io: deal with wandering queue limits when handling REQ_DISCARD and REQ_WRITE_SAME
dm snapshot: suspend merging snapshot when doing exception handover
dm snapshot: suspend origin when doing exception handover
dm: hold suspend_lock while suspending device during device deletion
dm thin: fix to consistently zero-fill reads to unprovisioned blocks
|
|
Pull UBI fix from Artem Bityutskiy:
"This fixes a bug introduced during the v4.0 merge window where we
forgot to put braces where they should be"
* tag 'upstream-4.0-rc5' of git://git.infradead.org/linux-ubifs:
UBI: fix missing brace control flow
|
|
The BCM43362 firmware falsely reports it is capable of providing
MBSS. As a result AP mode no longer works for this device. Therefor
disable MBSS in the driver for this chipset.
Cc: stable@vger.kernel.org # 3.19.y
Reported-by: Jorg Krause <jkrause@posteo.de>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
* pm-cpuidle:
cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
cpuidle: mvebu: Fix the CPU PM notifier usage
* powercap:
powercap / RAPL: handle domains with different energy units
* irq-pm:
rtc: at91rm9200: double locking bug in at91_rtc_interrupt()
* acpi-resources:
Revert "x86/PCI: Refine the way to release PCI IRQ resources"
|
|
If ->run() fails, it can either free the data structures it
allocated, or leave that task to ->free() which will be called
on failures.
However:
md.c calls ->free() even if ->private_data is NULL, which
causes problems in some personalities.
raid0.c frees the data, but doesn't clear ->private_data,
which will become a problem when we fix md.c
So better fix both these issues at once.
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Fixes: 5aa61f427e4979be733e4847b9199ff9cc48a47e
URL: https://bugzilla.kernel.org/show_bug.cgi?id=94381
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When an EEH error occurs, the device/slot is disconnected. This condition
is more reliably detected (i.e., returns all ones) with an MMIO read rather
than a config read -- especially on power platforms.
Hence, this patch fixes EEH error detection by replacing config reads with
MMIO reads for reading the error registers. The error registers in
Skyhawk-R/BE2/BE3 are accessible both via the config space and the
PCICFG (BAR0) memory space.
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Issuing this cmd for more than 8 EQs does not have the intended effect
even on BEx and Skyhawk-R.
This patch fixes this by issuing this cmd for upto 8 EQs at a time.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, a PF does not restrict its VF interface from enabling vlan
promiscuous mode. This breaks vlan isolation when a vlan
(transparent tagging) is configured on a VF.
This patch fixes this problem by disabling the vlan promisc capability
for VFs.
Reported-by: Yoann Juet <veilletechno-irts@univ-nantes.fr>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b4b55cda5874 (Refine the way to release PCI IRQ resources)
introduced a regression in the PCI IRQ resource management by causing
the IRQ resource of a device, established when pci_enabled_device()
is called on a fully disabled device, to be released when the driver
is unbound from the device, regardless of the enable_cnt.
This leads to the situation that an ill-behaved driver can now make a
device unusable to subsequent drivers by an imbalance in their use of
pci_enable/disable_device(). That is a serious problem for secondary
drivers like vfio-pci, which are innocent of the transgressions of
the previous driver.
Since the solution of this problem is not immediate and requires
further discussion, revert commit b4b55cda5874 and the issue it was
supposed to address (a bug related to xen-pciback) will be taken
care of in a different way going forward.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
Backporting a couple of plane related fixes from drm-next to v4.0.
* tag 'drm-intel-fixes-2015-03-19' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Make sure the primary plane is enabled before reading out the fb state
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
|
|
git://people.freedesktop.org/~gabbayo/linux into drm-fixes
- Fixing SDMA initialization when in non-HWS mode (debug mode)
- Memory leak fix when destroying kernel queue
- Fix number of available compute pipelines according to new firmware
* tag 'drm-amdkfd-fixes-2015-03-19' of git://people.freedesktop.org/~gabbayo/linux:
drm/radeon: Changing number of compute pipe lines
drm/amdkfd: Fix SDMA queue init. in non-HWS mode
drm/amdkfd: destroy mqd when destroying kernel queue
|
|
emulate_write_cache is 0
A check that rejects a CDB with FUA bit set if no write cache is
emulated was added by the following commit:
fde9f50 target: Add sanity checks for DPO/FUA bit usage
The condition is as follows:
if (!dev->dev_attrib.emulate_fua_write ||
!dev->dev_attrib.emulate_write_cache)
However, this check is wrong if the backend device supports WCE but
"emulate_write_cache" is disabled.
This patch uses se_dev_check_wce() (previously named
spc_check_dev_wce) to invoke transport->get_write_cache() if the
device has a write cache or check the "emulate_write_cache" attribute
otherwise.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a NULL pointer dereference triggered by a late
target_configure_device() -> alloc_workqueue() failure that results
in target_free_device() being called with DF_CONFIGURED already set,
which subsequently OOPses in destroy_workqueue() code.
Currently this only happens at modprobe target_core_mod time when
core_dev_setup_virtual_lun0() -> target_configure_device() fails,
and the explicit target_free_device() gets called.
To address this bug originally introduced by commit 0fd97ccf45, go
ahead and move DF_CONFIGURED to end of target_configure_device()
code to handle this special failure case.
Reported-by: Claudio Fleiner <cmf@daterainc.com>
Cc: Claudio Fleiner <cmf@daterainc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a NULL pointer dereference OOPs with pSCSI backends
within target_core_stat.c code. The bug is caused by a configfs attr
read if no pscsi_dev_virt->pdv_sd has been configured.
Reported-by: Olaf Hering <olaf@aepfle.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a missing set of conditional check braces in
ft_invl_hw_context() originally introduced by commit dcd998ccd
when handling DDP failures in ft_recv_write_data() code.
commit dcd998ccdbf74a7d8fe0f0a44e85da1ed5975946
Author: Kiran Patil <kiran.patil@intel.com>
Date: Wed Aug 3 09:20:01 2011 +0000
tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: <stable@vger.kernel.org> # 3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a se_cmd->cmd_kref leak buf when se_sess->sess_tearing_down
is true within target_get_sess_cmd() submission path code.
This se_cmd reference leak can occur during active session shutdown when
ack_kref=1 is passed by target_submit_cmd_[map_sgls,tmr]() callers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch changes loopback, usb-gadget, vhost-scsi and xen-scsiback
fabric code to invoke transport_register_session() instead of the
unprotected flavour, to ensure se_tpg->session_lock is taken when
adding new session list nodes to se_tpg->tpg_sess_list.
Note that since these four fabric drivers already hold their own
internal TPG mutexes when accessing se_tpg->tpg_sess_list, and
consist of a single se_session created through configfs attribute
access, no list corruption can currently occur.
So for correctness sake, go ahead and use the se_tpg->session_lock
protected version for these four fabric drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
