| Age | Commit message (Collapse) | Author |
|---|
|
According to Jonathan, variable reference voltages are very rare. It is
unlikely it is needed, and supporting it makes the code a bit more
complex.
Simplify the driver and drop the variable vref support.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/59106e24332743a7f9eb0b13ad6a2f5595ab485a.1745823530.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Currently, SPI-Engine offload module always sends 32-bit data elements to
DMA engine. Appropriately, when set for SPI offloading, the IIO driver uses
32 storagebits for IIO ADC channel buffer elements. However, setting SPI
transfer length according to storagebits (32-bits in case of offload) can
lead to unnecessarily long transfers for ADCs that are 16-bit or less
precision. Adjust AD4000 single-shot read to run transfers of 2 bytes when
that is enough to get all ADC data bits.
Fixes: 59b51edf717b ("iio: adc: ad4000: Add support for SPI offload")
Suggested-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/8f765cfd6e93fad4e755dd95d709b7bea2a388e2.1744718916.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for optional HW reset.
If specified, a reset will be asserted during driver probe.
Co-developed-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250428-mcp3911-fixes-v2-3-406e39330c3d@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The conversion result registers differs between devices. Make sure the
mapping is correct by using a device dependent .get_raw() callback function.
Fixes: 732ad34260d3 ("iio: adc: mcp3911: add support for the whole MCP39xx family")
Co-developed-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250428-mcp3911-fixes-v2-1-406e39330c3d@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Change the type of the buffer elements to u16 since we currently only
support 16-bit word size. The code was originally written to also allow
for 32-bit word size when oversampling is enabled, but so far,
oversampling is only implemented when using SPI offload and therefore
doesn't use this buffer.
AD4695_MAX_CHANNEL_SIZE macro is dropped since it no longer adds any
value.
AD4695_MAX_CHANNELS + 2 is changed to AD4695_MAX_CHANNELS + 1 because
previously we were overallocating. AD4695_MAX_CHANNELS is the number of
of voltage channels and + 1 is for the temperature channel.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Link: https://patch.msgid.link/20250428-iio-introduce-iio_declare_buffer_with_ts-v4-2-6f7f6126f1cb@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The AD3530/AD3530R (8-channel) and AD3531/AD3531R (4-channel) are
low-power, 16-bit, buffered voltage output DACs with software-
programmable gain controls, providing full-scale output spans of 2.5V or
5V for reference voltages of 2.5V. These devices operate from a single
2.7V to 5.5V supply and are guaranteed monotonic by design. The "R"
variants include a 2.5V, 5ppm/°C internal reference, which is disabled
by default.
Support for monitoring internal die temperature, output voltages, and
current of a selected channel via the MUXOUT pin using an external ADC
is currently not implemented.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250429-togreg-v7-3-0af9c543b545@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use struct with aligned_s64 timestamp to make timestamp alignment
explicit. Technically, what we have works because for all known
architectures, IIO_DMA_MINALIGN is a multiple of __alignof__(s64).
But this way, we don't have to make people read the comments to know
why there are extra elements in each buffer.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250428-iio-adc-ad7606-fix-buffer-alignment-v1-1-88dfc57e5df0@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Validate the scan mask when SPI offloading is being used.
Since this family of ADCs is simultaneous sampling, there isn't a way
to selectively disable channels when reading sample data. (Technically,
AD7616 has a sequencer so the driver could have some control, but that
is for another day).
For "regular" IIO triggered buffer reads, this isn't a problem and the
IIO core will demux the data and ignore data from disabled channels.
However, since SPI offloading is done completely in hardware, we don't
have a way to do the same. So before this patch, if less than all
channels were enabled, the data would be misplaced in the buffer.
By adding a check in update_scan_mode, we can fail to enable the buffer
instead of having bad data returned to userspace.
Fixes: e96d35faf357 ("iio: adc: ad7606: add SPI offload support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250502-iio-adc-ad7606_spi-fix-offload-scan-mask-check-v2-1-e70c6d71baa3@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for configurating the ADC reference (internal/external).
According to the datasheet, the external reference is enabled by
default.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250422085529.4407-2-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Both ad7091r_writeable_reg() and ad7091r_volatile_reg() perform the
same test, checking whether a given 'reg' code is
AD7091R_REG_RESULT or AD7091R_REG_ALERT. As the volatile ad7091r
registers happen to be the only read-only ones, the volatile_reg()
function now returns the negated output of writeable_reg().
Co-developed-by: Bruno Stephan <bruno.stephan@usp.br>
Signed-off-by: Bruno Stephan <bruno.stephan@usp.br>
Co-developed-by: Andre de Lima <aschwarz@usp.br>
Signed-off-by: Andre de Lima <aschwarz@usp.br>
Signed-off-by: Arthur Pilone <art.pilone@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://patch.msgid.link/20250421145534.91146-1-arthurpilone@usp.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Drop the sensor_data array from struct bmp280_data and replace it using
local structs in each interrupt handler.
The sensor_data array in struct bmp280_data is not used to share data
between functions and isn't used for DMA, so there isn't really a need
to have it in the struct. Instead, we can use the struct pattern for
scan data in each interrupt handler. This has the advantage of allowing
us to see the actual layout of each scan buffer for each different type
of supported sensor. It also avoid juggling values between local
variables and the array which makes the code a bit simpler by avoiding
some extra assignments.
We can also drop the BME280_NUM_MAX_CHANNELS macro as it is no longer
used.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Link: https://lore.kernel.org/linux-iio/20250421135540.1a667221@jic23-huawei/
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250422-iio-pressure-bmp280-rework-push-to-buffers-v1-1-ee722f29aeca@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for Winsen MHZ19B CO2 sensor.
Datasheet: https://www.winsen-sensor.com/d/files/infrared-gas-sensor/mh-z19b-co2-ver1_0.pdf
Signed-off-by: Gyeyoung Baek <gye976@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250423194100.53934-4-gye976@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The contents of kxcjk1013_setup_any_motion_interrupt and
kxcj1013_setup_new_data_interrupt are very similar. Deduplicate these
functions by introducing a generic function named
kxcjk1013_setup_interrupt that has an additional flag indicating if
it's a new data interrupt.
Signed-off-by: Gustavo Vaz <gustavo.vaz@usp.br>
Co-developed-by: Francisco Henriques <franciscolealhenriques@usp.br>
Signed-off-by: Francisco Henriques <franciscolealhenriques@usp.br>
Link: https://patch.msgid.link/20250423204631.16460-1-gustavo.vaz@usp.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
|hwfifo_timeout| is used by the EC firmware only when new samples are
available.
When the timeout changes, espcially when the new timeout is shorter than
the current one, send the samples waiting in the FIFO to the host.
Inline the call to transmit |hwfifo_timeout| value to the firmware.
Now flush when a sensor is suspended (ODR set to 0) as well.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://patch.msgid.link/20250423220506.2061021-1-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Consolidate duplicated logic from zopt2201_write_scale_als_by_idx() and
zopt2201_write_scale_uvb_by_idx() into a new generic helper function
zopt2201_write_scale_by_idx(). This function takes an additional
parameter: a pointer to a zopt2201_scale array.
To support this, the previously anonymous and duplicated struct used in
the scale arrays was promoted to a named struct: zopt2201_scale.
This change also corrects an incorrect array access that existed in
zopt2201_write_scale_uvb_by_idx().
Signed-off-by: Beatriz Viana Costa <beatrizvianacosta16@gmail.com>
Co-developed-by: Gabriela Victor <gabevictor333@gmail.com>
Signed-off-by: Gabriela Victor <gabevictor333@gmail.com>
Link: https://patch.msgid.link/20250424002144.23260-1-beatrizvianacosta16@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix a typo,(PAC1934 -> PAC193X), into the link from an application note
related to the ACPI device definition.
Fixes: 0fb528c8255b ("iio: adc: adding support for PAC193x")
Reported-by: Matteo Martelli <matteomartelli3@gmail.com>
Closes: https://patch.msgid.link/172794015844.2520.11909797050797595912@njaxe.localdomain
Signed-off-by: Marius Cristea <marius.cristea@microchip.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250424-pac1934-doc_link-v1-1-9832445cb270@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add oversampling support for STM32H7, STM32MP15 & STM32MP13.
STM32F4 ADC has no oversampling feature.
The current support of the oversampling feature aims at increasing the
data SNR, without changing the data resolution.
As the oversampling by itself increases data resolution, a right shift
is applied to keep the initial resolution.
Only the oversampling ratio corresponding to a power of two are
supported here, to get a direct link between right shift and
oversampling ratio. (2^n ratio <=> n right shift)
The oversampling ratio is shared by all channels, whatever channel type.
(e.g. single ended or differential).
Oversampling can be configured using IIO ABI:
- oversampling_ratio_available
- oversampling_ratio
Co-developed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250424151604.626758-1-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The AD5933 datasheet (Table 13) lists the maximum cycles to be 0x7FC
(2044).
Clamp the user input to the maximum effective value of 0x7FC cycles.
Fixes: f94aa354d676 ("iio: impedance-analyzer: New driver for AD5933/4 Impedance Converter, Network Analyzer")
Cc: stable@vger.kernel.org
Signed-off-by: Gabriel Shahrouzi <gshahrouzi@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://patch.msgid.link/20250420013009.847851-1-gshahrouzi@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Remove __aligned(16) in the scan data struct in the hid-sensor-rotation
driver. There is nothing in the code that requires this alignment.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250418-iio-orientation-hid-sensor-rotation-remove-alignment-v1-1-6da68eae7ecf@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use a struct with aligned s64_timestamp instead of a padded array for
the buffer used for iio_push_to_buffers_with_ts(). This makes it easier
to see the correctness of the size and alignment of the buffer.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250418-iio-prefer-aligned_s64-timestamp-v1-3-4c6080710516@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Set the suppress bit feature to the double tap detection, whenever
double tap is enabled. This impedes the suppress bit dangling in any
state, and thus varying in sensitivity for double tap detection.
Any tap event is defined by a rising signal edge above threshold, i.e.
duration time starts counting; and the falling edge under threshold
within duration time, i.e. then the tap event is issued. This means
duration is used individually for each tap event.
For double tap detection after a single tap, a latency time needs to be
specified. Usually tap events, i.e. spikes above and returning below
threshold will be ignored within latency. After latency, the window
time starts counting for a second tap detection which has to happen
within a duration time.
If the suppress bit is not set, spikes within latency time are ignored.
Setting the suppress bit will invalidate the double tap function. The
sensor will thus be able to save the window time for double tap
detection, and follow a more strict definition of what signal qualifies
for a double tap.
In a summary having the suppress bit set, fewer signal spikes will be
considered as double taps. This is an optional add on to double tap,
thus a separate patch.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250414184245.100280-5-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add the double tap feature of the sensor. The interrupt handler needs
to catch and forward the event to the IIO channel. The single tap
implementation now is extended to deal with double tap as well.
Doubletap introduces window and latency times, both in us. Since both
times are scaled, the 8-bit register value is stored in hardware,
where the scaled value in [us] is stored as member variable.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250414184245.100280-4-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add the single tap feature with a threshold in 62.5mg/LSB points and a
scaled duration in us. Keep singletap threshold in regmap cache but
the scaled value of duration in us as member variable.
Both use IIO channels for individual enable of the x/y/z axis. Initializes
threshold and duration with reasonable content. When an interrupt is
caught it will be pushed to the according IIO channel.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250414184245.100280-3-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Move the fifo handling into a separate function. This is a preparation
for a generic handling of the interrupt status register results. The
function is supposed to handle particular sensor events, and later to
forward them to the iio channel. This is needed to read out the interrupt
status register.
The function shall return occurring errors, if any, or 0 in case of
handled events or read fifo content. Thus migrate fifo read-out and push
fifo content to iio channels into this function to be built up with
additional event handling.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250414184245.100280-2-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This code was converted to use guard locks but one of the unlocks was
accidentally overlooked. Delete it.
Fixes: 135e101f4dd6 ("iio: dac: ad5592r: use lock guards")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/Z_-P7bsD3KL5K25R@stanley.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This is a leftover from the patch: commit 566564e80b0e ("staging: iio:
ad9832: use clock framework for clock reference").
The AD9832 driver uses the Common Clock Framework (CCF) to obtain the
master clock (MCLK) frequency rather than relying on a frequency value
passed from platform data.
Signed-off-by: Gabriel Shahrouzi <gshahrouzi@gmail.com>
Link: https://patch.msgid.link/20250417173333.607844-1-gshahrouzi@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use bitfield and bitmask macros to clearly specify AD9832 SPI
command fields to make register write code more readable.
Suggested-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Siddharth Menon <simeddon@gmail.com>
Link: https://patch.msgid.link/20250416140259.13431-1-simeddon@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Follow the pattern of other drivers and use aligned_s64 for the
timestamp. Technically there was no issue here since
AD74413R_FRAME_SIZE * AD74413R_CHANNEL_MAX == 16 and IIO_DMA_MINALIGN
is always a multiple of 8. But best to conform in case someone copies
this to new code and then tweaks something.
Also move the unaligned.h header while touching this since it was the
only one not in alphabetical order.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250417-iio-more-timestamp-alignment-v1-3-eafac1e22318@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Follow the pattern of other drivers and use aligned_s64 for the
timestamp. This will ensure that the timestamp is correctly aligned on
all architectures. It also ensures that the struct itself it also 8-byte
aligned so we can drop the explicit __aligned(8) attribute.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250417-iio-more-timestamp-alignment-v1-2-eafac1e22318@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
runtime checks.
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-21-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
runtime checks.
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com> # ROHM BM1390
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-20-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
On x86_32 s64 fields are only 32-bit aligned. Hence force the alignment of
the field and padding in the structure by using aligned_s64 instead.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-19-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
runtime checks.
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-18-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The driver previously used an array of two s64, then type cast the
pointer to write an s16 to the start. The code is made more readable
using a structure. At the same time switch to the new
iio_push_to_buffers_with_ts() helper to enable runtime checking of the
size of the source buffer.
Note that this approach uses a structure with holes, so use memset()
to ensure those do not contain old kernel data as this data is passed
to userspace.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-17-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
runtime checks.
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-16-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
runtime checks.
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-15-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
runtime checks.
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-13-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
runtime checks.
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. For this case, the length being provided
is already passed into the caller function so reuse that.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-12-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
checks.
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-11-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
checks.
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-10-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
length sanity check.
By providing the size of the buffer used, runtime checks can be performed
to ensure not overrun.
Also change the pushed data pointer to be that of the structure that also
contains the timestamp. Not an actual bug but semantically incorrect to
push the channel data when we want the storage with the timestamp as well.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-9-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Provide the storage size so that the helper can sanity check that it
is large enough for the configured channels.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-8-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
It has long been discouraged for drivers to make use of iio_dev->scan_bytes
directly as that is an implementation detail of the core. As such our
example driver should definitely not be doing so.
In order to illustrate the more complex case, where a DMA safe buffer is
needed, continue to kzalloc() the storage (but with a structure definition
to provide an explicit data layout). Also add comments on when a DMA safe
buffer is necessary and the two common ways of obtaining one.
Whilst we have a mixture of signed and unsigned channels, the unsigned
channels have ranges that can be stored in a signed value - hence
use signed storage for all channels, simplifying the structure definition.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-7-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
wait_event_interruptible_timeout requires a timeout argument
in units of jiffies. It was being called in usbtmc_get_stb
with the usb timeout value which is in units of milliseconds.
Pass the timeout argument converted to jiffies.
Fixes: 048c6d88a021 ("usb: usbtmc: Add ioctls to set/get usb timeout")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250521121656.18174-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usbtmc488_ioctl_read_stb function relied on a positive return from
usbtmc_get_stb to reset the srq condition in the driver. The
USBTMC_IOCTL_GET_STB case tested for a positive return to return the stb
to the user.
Commit: <cac01bd178d6> ("usb: usbtmc: Fix erroneous get_stb ioctl
error returns") changed the return value of usbtmc_get_stb to 0 on
success instead of returning the value of usb_control_msg which is
positive in the normal case. This change caused the function
usbtmc488_ioctl_read_stb and the USBTMC_IOCTL_GET_STB ioctl to no
longer function correctly.
Change the test in usbtmc488_ioctl_read_stb to test for failure
first and return the failure code immediately.
Change the test for the USBTMC_IOCTL_GET_STB ioctl to test for 0
instead of a positive value.
Fixes: cac01bd178d6 ("usb: usbtmc: Fix erroneous get_stb ioctl error returns")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250521121656.18174-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 4dbd2b2ebe4c ("nvme-multipath: Add visibility for round-robin
io-policy") introduced the creation of the multipath sysfs group under
the NVMe head gendisk device node. However, it also inadvertently added
the same sysfs group under each namespace path device which head node
refers to and that is incorrect.
The multipath sysfs group should only be exposed through the namespace
head gendisk node. This is sufficient, as the head device already
provides symbolic links to the individual namespace paths it manages.
This patch fixes the issue by preventing the creation of the multipath
sysfs group under namespace path devices, ensuring it only appears under
the head disk node.
Fixes: 4dbd2b2ebe4c ("nvme-multipath: Add visibility for round-robin io-policy")
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
irq_domain_add_tree() is going away as being obsolete now. Switch to
the preferred irq_domain_create_tree(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20250319092951.37667-37-jirislaby@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20250518032330.2959766-5-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The connected PMU contains several useful nvmem cells such as RTC offset,
boot failure counters, reboot/shutdown selector, and a few others.
In addition M3+ machines have their USB-PD controller connected via SPMI.
Signed-off-by: Jean-Francois Bortolotti <jeff@borto.fr>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Co-developed-by: Sasha Finkelstein <fnkl.kernel@gmail.com>
Signed-off-by: Sasha Finkelstein <fnkl.kernel@gmail.com>
Link: https://lore.kernel.org/r/20250409-spmi-v4-2-eb81ecfd1f64@gmail.com
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20250518032330.2959766-4-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SPMI_HISI3670, the Hikey 970 SPMI controller driver, is only
required to use the Kirin 970 SPMI bus.
And the Kirin 970 is an ARM64-based SoC, it cannot be used on
platforms of other architectures.
Link: https://lore.kernel.org/all/b4810f476e41e7de4efdf28b42472ae4ffe7defe.1597647359.git.mchehab+huawei@kernel.org/
Reported-by: Wentao Guan <guanwentao@uniontech.com>
Closes: https://github.com/deepin-community/kernel/pull/604
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://lore.kernel.org/r/23BAA675A75EF4F5+20250218050552.57711-1-wangyuli@uniontech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20250518032330.2959766-2-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
unregister_sysctl_table() checks for NULL pointers internally.
Remove unneeded NULL check here.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Link: https://lore.kernel.org/r/20250514032637.2317639-1-nichen@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
