Merge tag 'gemini-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt

Pull "Gemini DTS updates for ARM SoC take one" from Linus Walleij:

* tag 'gemini-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: dts: gemini: add pin control set-up for the SoC
  ARM: dts: Add DTS file for D-Link DIR-685
  ARM: dts: gemini: Switch to using macros

8 files changed, 543 insertions, 28 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e0d77ab79f5f..fb657c7b90fe 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -180,6 +180,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \
 	exynos5440-ssdk5440.dtb \
 	exynos5800-peach-pi.dtb
 dtb-$(CONFIG_ARCH_GEMINI) += \
+	gemini-dlink-dir-685.dtb \
 	gemini-nas4220b.dtb \
 	gemini-rut1xx.dtb \
 	gemini-sq201.dtb \
diff --git a/arch/arm/boot/dts/gemini-dlink-dir-685.dts b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
new file mode 100644
index 000000000000..e75e2d44371c
--- /dev/null
+++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
@@ -0,0 +1,246 @@
+/*
+ * Device Tree file for D-Link DIR-685 Xtreme N Storage Router
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "D-Link DIR-685 Xtreme N Storage Router";
+	compatible = "dlink,dir-685", "cortina,gemini";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		/* 128 MB SDRAM in 2 x Hynix HY5DU121622DTP-D43 */
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	chosen {
+		stdout-path = "uart0:115200n8";
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		button-esc {
+			debounce_interval = <50>;
+			wakeup-source;
+			linux,code = <KEY_ESC>;
+			label = "reset";
+			/* Collides with LPC_LAD[0], UART DCD, SSP 97RST */
+			gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
+		};
+		button-eject {
+			debounce_interval = <50>;
+			wakeup-source;
+			linux,code = <KEY_EJECTCD>;
+			label = "unmount";
+			/* Collides with LPC LFRAME, UART RTS, SSP TXD */
+			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-wps {
+			label = "dir685:blue:WPS";
+			/* Collides with ICE */
+			gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+		/*
+		 * These two LEDs are on the side of the device.
+		 * For electrical reasons, both LEDs cannot be active
+		 * at the same time so only blue or orange can on at
+		 * one time. Enabling both makes the LED go dark.
+		 * The LEDs both sit inside the unmount button and the
+		 * label on the case says "unmount".
+		 */
+		led-blue-hd {
+			label = "dir685:blue:HD";
+			/* Collides with LPC_SERIRQ, UART DTR, SSP FSC pins */
+			gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led-orange-hd {
+			label = "dir685:orange:HD";
+			/* Collides with LPC_LAD[2], UART DSR, SSP ECLK pins */
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	/*
+	 * This is a Sunon Maglev GM0502PFV2-8 cooling fan @10000 RPM.
+	 * Since the platform has no temperature sensor, this is controlled
+	 * from userspace by using the hard disks S.M.A.R.T. temperature
+	 * sensor. It is turned on when the temperature exceeds 46 degrees
+	 * and turned off when the temperatures goes below 41 degrees
+	 * (celsius).
+	 */
+	gpio-fan {
+		compatible = "gpio-fan";
+		/* Collides with IDE */
+		gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		gpio-fan,speed-map = <0 0>, <10000 1>;
+		#cooling-cells = <2>;
+	};
+
+	/*
+	 * The touchpad input is connected to a GPIO bit-banged
+	 * I2C bus.
+	 */
+	gpio-i2c {
+		compatible = "i2c-gpio";
+		/* Collides with ICE */
+		gpios = <&gpio0 5 0>, /* SDA */
+			<&gpio0 6 0>; /* SCL */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		touchkeys@26 {
+			compatible = "dlink,dir685-touchkeys";
+			reg = <0x26>;
+			interrupt-parent = <&gpio0>;
+			/* Collides with NAND flash */
+			interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+
+	soc {
+		flash@30000000 {
+			status = "okay";
+			/* 32MB of flash */
+			reg = <0x30000000 0x02000000>;
+
+			/*
+			 * This "RedBoot" is the Storlink derivative.
+			 */
+			partition@0 {
+				label = "RedBoot";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+			/*
+			 * Between the boot loader and the rootfs is the kernel
+			 * in a custom Storlink format flashed from the boot
+			 * menu. The rootfs is in squashfs format.
+			 */
+			partition@1800c0 {
+				label = "rootfs";
+				reg = <0x001800c0 0x01dbff40>;
+				read-only;
+			};
+			partition@1f40000 {
+				label = "upgrade";
+				reg = <0x01f40000 0x00040000>;
+				read-only;
+			};
+			partition@1f80000 {
+				label = "rgdb";
+				reg = <0x01f80000 0x00040000>;
+				read-only;
+			};
+			/*
+			 * This partition contains MAC addresses for WAN,
+			 * WLAN and LAN, and the country code (for wireless
+			 * I guess).
+			 */
+			partition@1fc0000 {
+				label = "nvram";
+				reg = <0x01fc0000 0x00020000>;
+				read-only;
+			};
+			partition@1fe0000 {
+				label = "LangPack";
+				reg = <0x01fe0000 0x00020000>;
+				read-only;
+			};
+		};
+
+		syscon: syscon@40000000 {
+			pinctrl {
+				/*
+				 * gpio0bgrp cover line 5, 6 used by TK I2C
+				 * gpio0bgrp cover line 7 used by WPS LED
+				 * gpio0cgrp cover line 8, 13 used by keys
+				 *           and 11, 12 used by the HD LEDs
+				 * gpio0egrp cover line 16 used by VDISP
+				 * gpio0fgrp cover line 17 used by TK IRQ
+				 * gpio0ggrp cover line 20 used by panel CS
+				 * gpio0hgrp cover line 21,22 used by RTL8366RB
+				 */
+				gpio0_default_pins: pinctrl-gpio0 {
+					mux {
+						function = "gpio0";
+						groups = "gpio0bgrp",
+						"gpio0cgrp",
+						"gpio0egrp",
+						"gpio0fgrp",
+						"gpio0ggrp",
+						"gpio0hgrp";
+					};
+				};
+				/*
+				 * gpio1bgrp cover line 5,8,7 used by panel SPI
+				 * also line 6 used by the fan
+				 *
+				 */
+				gpio1_default_pins: pinctrl-gpio1 {
+					mux {
+						function = "gpio1";
+						groups = "gpio1bgrp";
+					};
+				};
+			};
+		};
+
+		sata: sata@46000000 {
+			cortina,gemini-ata-muxmode = <0>;
+			cortina,gemini-enable-sata-bridge;
+			status = "okay";
+		};
+
+		gpio0: gpio@4d000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio0_default_pins>;
+		};
+
+		gpio1: gpio@4e000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio1_default_pins>;
+		};
+
+		pci@50000000 {
+			status = "okay";
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+				<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+				<0x4800 0 0 2 &pci_intc 1>,
+				<0x4800 0 0 3 &pci_intc 2>,
+				<0x4800 0 0 4 &pci_intc 3>,
+				<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+				<0x5000 0 0 2 &pci_intc 2>,
+				<0x5000 0 0 3 &pci_intc 3>,
+				<0x5000 0 0 4 &pci_intc 0>,
+				<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+				<0x5800 0 0 2 &pci_intc 3>,
+				<0x5800 0 0 3 &pci_intc 0>,
+				<0x5800 0 0 4 &pci_intc 1>,
+				<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+				<0x6000 0 0 2 &pci_intc 0>,
+				<0x6000 0 0 3 &pci_intc 1>,
+				<0x6000 0 0 4 &pci_intc 2>;
+		};
+
+		ata@63000000 {
+			status = "okay";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/gemini-nas4220b.dts b/arch/arm/boot/dts/gemini-nas4220b.dts
index 55f6a4f1f801..b4fc58c8cf8d 100644
--- a/arch/arm/boot/dts/gemini-nas4220b.dts
+++ b/arch/arm/boot/dts/gemini-nas4220b.dts
@@ -33,6 +33,7 @@
 			wakeup-source;
 			linux,code = <KEY_SETUP>;
 			label = "Backup button";
+			/* Conflict with TVC */
 			gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
 		};
 		button@31 {
@@ -40,6 +41,7 @@
 			wakeup-source;
 			linux,code = <KEY_RESTART>;
 			label = "Softreset button";
+			/* Conflict with TVC */
 			gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -48,11 +50,13 @@
 		compatible = "gpio-leds";
 		led@28 {
 			label = "nas4220b:orange:hdd";
+			/* Conflict with TVC */
 			gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 		led@30 {
 			label = "nas4220b:green:os";
+			/* Conflict with TVC */
 			gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
@@ -99,12 +103,32 @@
 			};
 		};
 
+		syscon: syscon@40000000 {
+			pinctrl {
+				/*
+				 * gpio1dgrp cover line 28-31 otherwise used
+				 * by TVC.
+				 */
+				gpio1_default_pins: pinctrl-gpio1 {
+					mux {
+						function = "gpio1";
+						groups = "gpio1dgrp";
+					};
+				};
+			};
+		};
+
 		sata: sata@46000000 {
 			cortina,gemini-ata-muxmode = <0>;
 			cortina,gemini-enable-sata-bridge;
 			status = "okay";
 		};
 
+		gpio1: gpio@4e000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio1_default_pins>;
+		};
+
 		ata@63000000 {
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/gemini-rut1xx.dts b/arch/arm/boot/dts/gemini-rut1xx.dts
index 7b920bfbda32..3613b264f45f 100644
--- a/arch/arm/boot/dts/gemini-rut1xx.dts
+++ b/arch/arm/boot/dts/gemini-rut1xx.dts
@@ -33,6 +33,7 @@
 			wakeup-source;
 			linux,code = <KEY_SETUP>;
 			label = "Reset to defaults";
+			/* Conflict with TVC */
 			gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -42,12 +43,14 @@
 		led@7 {
 			/* FIXME: add the LED color */
 			label = "rut1xx::gsm";
+			/* Conflict with ICE */
 			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 		led@31 {
 			/* FIXME: add the LED color */
 			label = "rut1xx::power";
+			/* Conflict with NAND CE0 */
 			gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 			linux,default-trigger = "heartbeat";
@@ -61,5 +64,41 @@
 			reg = <0x30000000 0x00800000>;
 			/* TODO: add flash partitions here */
 		};
+
+		syscon: syscon@40000000 {
+			pinctrl {
+				/*
+				 * gpio0bgrp cover line 7 used by GSM LED
+				 * gpio0fgrp cover line 17 used by power LED
+				 */
+				gpio0_default_pins: pinctrl-gpio0 {
+					mux {
+						function = "gpio0";
+						groups = "gpio0bgrp",
+						"gpio0fgrp";
+					};
+				};
+				/*
+				 * gpio1dgrp cover line 28-31 otherwise used
+				 * by TVC.
+				 */
+				gpio1_default_pins: pinctrl-gpio1 {
+					mux {
+						function = "gpio1";
+						groups = "gpio1dgrp";
+					};
+				};
+			};
+		};
+
+		gpio0: gpio@4d000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio0_default_pins>;
+		};
+
+		gpio1: gpio@4e000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio1_default_pins>;
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/gemini-sq201.dts b/arch/arm/boot/dts/gemini-sq201.dts
index 4d200f0bcd45..7cfa9caf47d4 100644
--- a/arch/arm/boot/dts/gemini-sq201.dts
+++ b/arch/arm/boot/dts/gemini-sq201.dts
@@ -33,6 +33,7 @@
 			wakeup-source;
 			linux,code = <KEY_SETUP>;
 			label = "factory reset";
+			/* Conflict with NAND flash */
 			gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -41,12 +42,14 @@
 		compatible = "gpio-leds";
 		led@20 {
 			label = "sq201:green:info";
+			/* Conflict with parallel flash */
 			gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 		led@31 {
 			label = "sq201:green:usb";
+			/* Conflict with parallel and NAND flash */
 			gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 			linux,default-trigger = "usb-host";
@@ -55,7 +58,15 @@
 
 	soc {
 		flash@30000000 {
-			status = "okay";
+			/*
+			 * Flash access can be enabled, with the side effect
+			 * of disabling access to GPIO LED on GPIO0[20] which
+			 * reuse one of the parallel flash chip select lines.
+			 * Also the default firmware on the machine has the
+			 * problem that since it uses the flash, the two LEDS
+			 * on the right become numb.
+			 */
+			/* status = "okay"; */
 			/* 16MB of flash */
 			reg = <0x30000000 0x01000000>;
 
@@ -93,12 +104,35 @@
 			};
 		};
 
+		syscon: syscon@40000000 {
+			pinctrl {
+				/*
+				 * gpio0fgrp cover line 18 used by reset button
+				 * gpio0ggrp cover line 20 used by info LED
+				 * gpio0kgrp cover line 31 used by USB LED
+				 */
+				gpio0_default_pins: pinctrl-gpio0 {
+					mux {
+						function = "gpio0";
+						groups = "gpio0fgrp",
+						"gpio0ggrp",
+						"gpio0kgrp";
+					};
+				};
+			};
+		};
+
 		sata: sata@46000000 {
 			cortina,gemini-ata-muxmode = <0>;
 			cortina,gemini-enable-sata-bridge;
 			status = "okay";
 		};
 
+		gpio0: gpio@4d000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio0_default_pins>;
+		};
+
 		pci@50000000 {
 			status = "okay";
 			interrupt-map-mask = <0xf800 0 0 7>;
diff --git a/arch/arm/boot/dts/gemini-wbd111.dts b/arch/arm/boot/dts/gemini-wbd111.dts
index 63b756e3bf5a..38a49e750478 100644
--- a/arch/arm/boot/dts/gemini-wbd111.dts
+++ b/arch/arm/boot/dts/gemini-wbd111.dts
@@ -33,6 +33,7 @@
 			wakeup-source;
 			linux,code = <KEY_SETUP>;
 			label = "reset";
+			/* Conflict with ICE */
 			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -42,21 +43,25 @@
 
 		led@1 {
 			label = "wbd111:red:L3";
+			/* Conflict with TVC and extended parallel flash */
 			gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 		led@2 {
 			label = "wbd111:green:L4";
+			/* Conflict with TVC and extended parallel flash */
 			gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 		led@3 {
 			label = "wbd111:red:L4";
+			/* Conflict with TVC and extended parallel flash */
 			gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 		led@5 {
 			label = "wbd111:green:L3";
+			/* Conflict with TVC and extended parallel flash */
 			gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
@@ -98,5 +103,26 @@
 				read-only;
 			};
 		};
+
+		syscon: syscon@40000000 {
+			pinctrl {
+				/*
+				 * gpio0agrp cover line 0-4
+				 * gpio0bgrp cover line 5
+				 */
+				gpio0_default_pins: pinctrl-gpio0 {
+					mux {
+						function = "gpio0";
+						groups = "gpio0agrp",
+						"gpio0bgrp";
+					};
+				};
+			};
+		};
+
+		gpio0: gpio@4d000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio0_default_pins>;
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/gemini-wbd222.dts b/arch/arm/boot/dts/gemini-wbd222.dts
index 9747f5a47807..f77e34e0df0b 100644
--- a/arch/arm/boot/dts/gemini-wbd222.dts
+++ b/arch/arm/boot/dts/gemini-wbd222.dts
@@ -33,6 +33,7 @@
 			wakeup-source;
 			linux,code = <KEY_SETUP>;
 			label = "reset";
+			/* Conflict with ICE */
 			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -42,21 +43,25 @@
 
 		led@1 {
 			label = "wbd111:red:L3";
+			/* Conflict with TVC and extended parallel flash */
 			gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 		led@2 {
 			label = "wbd111:green:L4";
+			/* Conflict with TVC and extended parallel flash */
 			gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 		led@3 {
 			label = "wbd111:red:L4";
+			/* Conflict with TVC and extended parallel flash */
 			gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 		led@5 {
 			label = "wbd111:green:L3";
+			/* Conflict with TVC and extended parallel flash */
 			gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
@@ -98,5 +103,26 @@
 				read-only;
 			};
 		};
+
+		syscon: syscon@40000000 {
+			pinctrl {
+				/*
+				 * gpio0agrp cover line 0-4
+				 * gpio0bgrp cover line 5
+				 */
+				gpio0_default_pins: pinctrl-gpio0 {
+					mux {
+						function = "gpio0";
+						groups = "gpio0agrp",
+						"gpio0bgrp";
+					};
+				};
+			};
+		};
+
+		gpio0: gpio@4d000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio0_default_pins>;
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/gemini.dtsi b/arch/arm/boot/dts/gemini.dtsi
index 141d8d3a1d07..c68e8d430234 100644
--- a/arch/arm/boot/dts/gemini.dtsi
+++ b/arch/arm/boot/dts/gemini.dtsi
@@ -5,6 +5,8 @@
 /include/ "skeleton.dtsi"
 
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/cortina,gemini-clock.h>
+#include <dt-bindings/reset/cortina,gemini-reset.h>
 #include <dt-bindings/gpio/gpio.h>
 
 / {
@@ -18,6 +20,8 @@
 		flash@30000000 {
 			compatible = "cortina,gemini-flash", "cfi-flash";
 			syscon = <&syscon>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pflash_default_pins>;
 			bank-width = <2>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -39,22 +43,123 @@
 				/* RESET_GLOBAL | RESET_CPU1 */
 				mask = <0xC0000000>;
 			};
+
+			pinctrl {
+				compatible = "cortina,gemini-pinctrl";
+				regmap = <&syscon>;
+				/* Hog the DRAM pins */
+				pinctrl-names = "default";
+				pinctrl-0 = <&dram_default_pins>, <&system_default_pins>,
+					    <&vcontrol_default_pins>;
+
+				dram_default_pins: pinctrl-dram {
+					mux {
+						function = "dram";
+						groups = "dramgrp";
+					};
+				};
+				rtc_default_pins: pinctrl-rtc {
+					mux {
+						function = "rtc";
+						groups = "rtcgrp";
+					};
+				};
+				power_default_pins: pinctrl-power {
+					mux {
+						function = "power";
+						groups = "powergrp";
+					};
+				};
+				cir_default_pins: pinctrl-cir {
+					mux {
+						function = "cir";
+						groups = "cirgrp";
+					};
+				};
+				system_default_pins: pinctrl-system {
+					mux {
+						function = "system";
+						groups = "systemgrp";
+					};
+				};
+				vcontrol_default_pins: pinctrl-vcontrol {
+					mux {
+						function = "vcontrol";
+						groups = "vcontrolgrp";
+					};
+				};
+				ice_default_pins: pinctrl-ice {
+					mux {
+						function = "ice";
+						groups = "icegrp";
+					};
+				};
+				uart_default_pins: pinctrl-uart {
+					mux {
+						function = "uart";
+						groups = "uartrxtxgrp";
+					};
+				};
+				pflash_default_pins: pinctrl-pflash {
+					mux {
+						function = "pflash";
+						groups = "pflashgrp";
+					};
+				};
+				usb_default_pins: pinctrl-usb {
+					mux {
+						function = "usb";
+						groups = "usbgrp";
+					};
+				};
+				gmii_default_pins: pinctrl-gmii {
+					mux {
+						function = "gmii";
+						groups = "gmiigrp";
+					};
+				};
+				pci_default_pins: pinctrl-pci {
+					mux {
+						function = "pci";
+						groups = "pcigrp";
+					};
+				};
+				sata_default_pins: pinctrl-sata {
+					mux {
+						function = "sata";
+						groups = "satagrp";
+					};
+				};
+				/* Activate both groups of pins for this state */
+				sata_and_ide_pins: pinctrl-sata-ide {
+					mux0 {
+						function = "sata";
+						groups = "satagrp";
+					};
+					mux1 {
+						function = "ide";
+						groups = "idegrp";
+					};
+				};
+			};
 		};
 
 		watchdog@41000000 {
 			compatible = "cortina,gemini-watchdog";
 			reg = <0x41000000 0x1000>;
 			interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&syscon 23>;
-			clocks = <&syscon 2>;
+			resets = <&syscon GEMINI_RESET_WDOG>;
+			clocks = <&syscon GEMINI_CLK_APB>;
 		};
 
 		uart0: serial@42000000 {
 			compatible = "ns16550a";
 			reg = <0x42000000 0x100>;
-			resets = <&syscon 18>;
-			clocks = <&syscon 6>;
+			resets = <&syscon GEMINI_RESET_UART>;
+			clocks = <&syscon GEMINI_CLK_UART>;
 			interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart_default_pins>;
 			reg-shift = <2>;
 		};
 
@@ -65,9 +170,9 @@
 			interrupts = <14 IRQ_TYPE_EDGE_FALLING>, /* Timer 1 */
 				     <15 IRQ_TYPE_EDGE_FALLING>, /* Timer 2 */
 				     <16 IRQ_TYPE_EDGE_FALLING>; /* Timer 3 */
-			resets = <&syscon 17>;
+			resets = <&syscon GEMINI_RESET_TIMER>;
 			/* APB clock or RTC clock */
-			clocks = <&syscon 2>, <&syscon 0>;
+			clocks = <&syscon GEMINI_CLK_APB>, <&syscon GEMINI_CLK_RTC>;
 			clock-names = "PCLK", "EXTCLK";
 			syscon = <&syscon>;
 		};
@@ -76,20 +181,30 @@
 			compatible = "cortina,gemini-rtc";
 			reg = <0x45000000 0x100>;
 			interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&syscon 16>;
-			clocks = <&syscon 2>, <&syscon 0>;
+			resets = <&syscon GEMINI_RESET_RTC>;
+			clocks = <&syscon GEMINI_CLK_APB>, <&syscon GEMINI_CLK_RTC>;
 			clock-names = "PCLK", "EXTCLK";
+			pinctrl-names = "default";
+			pinctrl-0 = <&rtc_default_pins>;
 		};
 
 		sata: sata@46000000 {
 			compatible = "cortina,gemini-sata-bridge";
 			reg = <0x46000000 0x100>;
-			resets = <&syscon 26>,
-				 <&syscon 27>;
+			resets = <&syscon GEMINI_RESET_SATA0>,
+				 <&syscon GEMINI_RESET_SATA1>;
 			reset-names = "sata0", "sata1";
-			clocks = <&syscon 10>,
-				 <&syscon 11>;
+			clocks = <&syscon GEMINI_CLK_GATE_SATA0>,
+				 <&syscon GEMINI_CLK_GATE_SATA1>;
 			clock-names = "SATA0_PCLK", "SATA1_PCLK";
+			/*
+			 * This defines the special "ide" state that needs
+			 * to be explicitly enabled to enable the IDE pins,
+			 * as these pins are normally used for other things.
+			 */
+			pinctrl-names = "default", "ide";
+			pinctrl-0 = <&sata_default_pins>;
+			pinctrl-1 = <&sata_and_ide_pins>;
 			syscon = <&syscon>;
 			status = "disabled";
 		};
@@ -97,7 +212,7 @@
 		intcon: interrupt-controller@48000000 {
 			compatible = "faraday,ftintc010";
 			reg = <0x48000000 0x1000>;
-			resets = <&syscon 14>;
+			resets = <&syscon GEMINI_RESET_INTCON0>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};
@@ -106,14 +221,16 @@
 			compatible = "cortina,gemini-power-controller";
 			reg = <0x4b000000 0x100>;
 			interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&power_default_pins>;
 		};
 
 		gpio0: gpio@4d000000 {
 			compatible = "cortina,gemini-gpio", "faraday,ftgpio010";
 			reg = <0x4d000000 0x100>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&syscon 20>;
-			clocks = <&syscon 2>;
+			resets = <&syscon GEMINI_RESET_GPIO0>;
+			clocks = <&syscon GEMINI_CLK_APB>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
@@ -124,8 +241,8 @@
 			compatible = "cortina,gemini-gpio", "faraday,ftgpio010";
 			reg = <0x4e000000 0x100>;
 			interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&syscon 21>;
-			clocks = <&syscon 2>;
+			resets = <&syscon GEMINI_RESET_GPIO1>;
+			clocks = <&syscon GEMINI_CLK_APB>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
@@ -136,8 +253,8 @@
 			compatible = "cortina,gemini-gpio", "faraday,ftgpio010";
 			reg = <0x4f000000 0x100>;
 			interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&syscon 22>;
-			clocks = <&syscon 2>;
+			resets = <&syscon GEMINI_RESET_GPIO2>;
+			clocks = <&syscon GEMINI_CLK_APB>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
@@ -151,9 +268,11 @@
 			 * to configure the host bridge.
 			 */
 			reg = <0x50000000 0x100>;
-			resets = <&syscon 7>;
-			clocks = <&syscon 15>, <&syscon 4>;
+			resets = <&syscon GEMINI_RESET_PCI>;
+			clocks = <&syscon GEMINI_CLK_GATE_PCI>, <&syscon GEMINI_CLK_PCI>;
 			clock-names = "PCLK", "PCICLK";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pci_default_pins>;
 			#address-cells = <3>;
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
@@ -193,8 +312,8 @@
 			compatible = "cortina,gemini-pata", "faraday,ftide010";
 			reg = <0x63000000 0x1000>;
 			interrupts = <4 IRQ_TYPE_EDGE_RISING>;
-			resets = <&syscon 2>;
-			clocks = <&syscon 14>;
+			resets = <&syscon GEMINI_RESET_IDE>;
+			clocks = <&syscon GEMINI_CLK_GATE_IDE>;
 			clock-names = "PCLK";
 			sata = <&sata>;
 			status = "disabled";
@@ -204,8 +323,8 @@
 			compatible = "cortina,gemini-pata", "faraday,ftide010";
 			reg = <0x63400000 0x1000>;
 			interrupts = <5 IRQ_TYPE_EDGE_RISING>;
-			resets = <&syscon 2>;
-			clocks = <&syscon 14>;
+			resets = <&syscon GEMINI_RESET_IDE>;
+			clocks = <&syscon GEMINI_CLK_GATE_IDE>;
 			clock-names = "PCLK";
 			sata = <&sata>;
 			status = "disabled";
@@ -217,8 +336,8 @@
 			arm,primecell-periphid = <0x0003b080>;
 			reg = <0x67000000 0x1000>;
 			interrupts = <9 IRQ_TYPE_EDGE_RISING>;
-			resets = <&syscon 10>;
-			clocks = <&syscon 1>;
+			resets = <&syscon GEMINI_RESET_DMAC>;
+			clocks = <&syscon GEMINI_CLK_AHB>;
 			clock-names = "apb_pclk";
 			/* Bus interface AHB1 (AHB0) is totally tilted */
 			lli-bus-interface-ahb2;