summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
authorArnd Bergmann <arnd@arndb.de>2025-03-19 21:42:19 +0100
committerArnd Bergmann <arnd@arndb.de>2025-03-19 21:42:19 +0100
commitfc7136e149e96c1563bccb51f7c30f6974749ec2 (patch)
tree3c1cdae9f154bb38f072c930202a7d675eaff559
parent35759662efffbf7b32fd2b14609fb301f40c73f5 (diff)
parent65954899a157832f68536b488194cf698248a26e (diff)
Merge tag 'stm32-dt-for-v6.15-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.15, round 1 Highlights: ---------- - MPU: - STM32MP13: - Add thermal support. - Add Priva E-Measuringbox board support based on sTM32MP133C SoC. It embeds Ethernet RMII with TI phy, SDCard, eMMC and some sensors. - Add support for DHCOR SoM and DHSBC rev.200 board: TPM interrupts and gpio reset + LDO2/LDO5 support. - STMP32MP15: - Add new Octavo support: LXA FairyTux 2 based on OSD32MP153C SiP. It contains eMMC for storage, a gigabit Ethernet, a CAN bus and a RS485 transceiver. - Add Plymovent AQM board based on STM32MP151 SoC. It embeds: ETH RMII, WLAN, BT, Sensors (CO2, PM, pressure), Audio (I2S), Storage (SDCard, eMMC). - STM32MP25: - Add STM32MP257F Discovery board: It embeds a STM32MP257FAL SoC, with 4GB of LPDDR4, 2*USB typeA, 1*USB3 typeC, 1*ETH, wifi/BT combo, DSI HDMI, LVDS connector ... - Introduce STM32MP23 SoC and add STM32MP235F Discovery board: It embeds a STM32MP235FAK SoC, with 4GB of LPDDR4, 2*USB typeA, 1*USB3 typeC, 1*ETH, wifi/BT combo, DSI HDMI, LVDS connector ... - Introduce STM32MP21 SoC and STM32MP215F discovery board: It embeds a STM32MP235FAN SoC, with 2GB of LPDDR4, 1*USB2 peripheral bus powered typeC, 1*ETH, wifi/BT combo, LCD 18bit connector, CSI camera connector, ... * tag 'stm32-dt-for-v6.15-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (26 commits) arm64: dts: st: add stm32mp215f-dk board support dt-bindings: stm32: document stm32mp215f-dk board arm64: dts: st: introduce stm32mp21 SoCs family arm64: dts: st: add stm32mp235f-dk board support dt-bindings: stm32: document stm32mp235f-dk board arm64: dts: st: introduce stm32mp23 SoCs family dt-bindings: stm32: add STM32MP21 and STM32MP23 compatibles for syscon arm64: Kconfig: expand STM32 Armv8 SoC with STM32MP21/STM32MP23 SoCs family arm64: dts: st: add stm32mp257f-dk board support dt-bindings: stm32: document stm32mp257f-dk board ARM: dts: stm32: Add Plymovent AQM devicetree ARM: dts: stm32: Add pinmux groups for Plymovent AQM board dt-bindings: arm: stm32: Add Plymovent AQM board dt-bindings: sound: convert ICS-43432 binding to YAML ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC rev.200 board ARM: dts: stm32: use IRQ_TYPE_EDGE_FALLING on stm32mp157c-dk2 ARM: dts: stm32: add usr3 LED node to stm32f769-disco ARM: dts: stm32: rename LEDs nodes for stm32f769-disco ARM: dts: stm32: add push button to stm32f746 Discovery board ARM: dts: stm32: add led to stm32f746 Discovery board ... Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Diffstat
-rw-r--r--Documentation/devicetree/bindings/arm/stm32/st,stm32-syscon.yaml2
-rw-r--r--Documentation/devicetree/bindings/arm/stm32/stm32.yaml22
-rw-r--r--Documentation/devicetree/bindings/sound/ics43432.txt19
-rw-r--r--Documentation/devicetree/bindings/sound/invensense,ics43432.yaml51
-rw-r--r--Documentation/devicetree/bindings/vendor-prefixes.yaml2
-rw-r--r--arch/arm/boot/dts/st/Makefile4
-rw-r--r--arch/arm/boot/dts/st/stm32f746-disco.dts18
-rw-r--r--arch/arm/boot/dts/st/stm32f769-disco.dts7
-rw-r--r--arch/arm/boot/dts/st/stm32mp131.dtsi35
-rw-r--r--arch/arm/boot/dts/st/stm32mp133c-prihmb.dts496
-rw-r--r--arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts30
-rw-r--r--arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi292
-rw-r--r--arch/arm/boot/dts/st/stm32mp151c-plyaqm.dts376
-rw-r--r--arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen1.dts103
-rw-r--r--arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen2.dts147
-rw-r--r--arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2.dtsi397
-rw-r--r--arch/arm/boot/dts/st/stm32mp157c-dk2.dts2
-rw-r--r--arch/arm64/Kconfig.platforms4
-rw-r--r--arch/arm64/boot/dts/st/Makefile6
-rw-r--r--arch/arm64/boot/dts/st/stm32mp211.dtsi128
-rw-r--r--arch/arm64/boot/dts/st/stm32mp213.dtsi9
-rw-r--r--arch/arm64/boot/dts/st/stm32mp215.dtsi9
-rw-r--r--arch/arm64/boot/dts/st/stm32mp215f-dk.dts49
-rw-r--r--arch/arm64/boot/dts/st/stm32mp21xc.dtsi8
-rw-r--r--arch/arm64/boot/dts/st/stm32mp21xf.dtsi8
-rw-r--r--arch/arm64/boot/dts/st/stm32mp231.dtsi1214
-rw-r--r--arch/arm64/boot/dts/st/stm32mp233.dtsi94
-rw-r--r--arch/arm64/boot/dts/st/stm32mp235.dtsi16
-rw-r--r--arch/arm64/boot/dts/st/stm32mp235f-dk.dts113
-rw-r--r--arch/arm64/boot/dts/st/stm32mp23xc.dtsi8
-rw-r--r--arch/arm64/boot/dts/st/stm32mp23xf.dtsi8
-rw-r--r--arch/arm64/boot/dts/st/stm32mp257f-dk.dts113
32 files changed, 3765 insertions, 25 deletions
diff --git a/Documentation/devicetree/bindings/arm/stm32/st,stm32-syscon.yaml b/Documentation/devicetree/bindings/arm/stm32/st,stm32-syscon.yaml
index d083d8ad48b7..ed97652c8492 100644
--- a/Documentation/devicetree/bindings/arm/stm32/st,stm32-syscon.yaml
+++ b/Documentation/devicetree/bindings/arm/stm32/st,stm32-syscon.yaml
@@ -21,6 +21,8 @@ properties:
- st,stm32f4-gcan
- st,stm32mp151-pwr-mcu
- st,stm32mp157-syscfg
+ - st,stm32mp21-syscfg
+ - st,stm32mp23-syscfg
- st,stm32mp25-syscfg
- const: syscon
- items:
diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
index b6c56d4ce6b9..5fee2f38ff25 100644
--- a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
+++ b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
@@ -51,9 +51,16 @@ properties:
- st,stm32mp135f-dk
- const: st,stm32mp135
+ - description: ST STM32MP133 based Boards
+ items:
+ - enum:
+ - pri,prihmb # Priva E-Measuringbox board
+ - const: st,stm32mp133
+
- description: ST STM32MP151 based Boards
items:
- enum:
+ - ply,plyaqm # Plymovent AQM board
- prt,mecio1r0 # Protonic MECIO1r0
- prt,mect1s # Protonic MECT1S
- prt,prtt1a # Protonic PRTT1A
@@ -94,6 +101,8 @@ properties:
- description: Octavo OSD32MP153 System-in-Package based boards
items:
- enum:
+ - lxa,stm32mp153c-fairytux2-gen1 # Linux Automation FairyTux 2 (Generation 1)
+ - lxa,stm32mp153c-fairytux2-gen2 # Linux Automation FairyTux 2 (Generation 2)
- lxa,stm32mp153c-tac-gen3 # Linux Automation TAC (Generation 3)
- const: oct,stm32mp153x-osd32
- const: st,stm32mp153
@@ -178,9 +187,22 @@ properties:
- description: ST STM32MP257 based Boards
items:
- enum:
+ - st,stm32mp257f-dk
- st,stm32mp257f-ev1
- const: st,stm32mp257
+ - description: ST STM32MP235 based Boards
+ items:
+ - enum:
+ - st,stm32mp235f-dk
+ - const: st,stm32mp235
+
+ - description: ST STM32MP215 based Boards
+ items:
+ - enum:
+ - st,stm32mp215f-dk
+ - const: st,stm32mp215
+
additionalProperties: true
...
diff --git a/Documentation/devicetree/bindings/sound/ics43432.txt b/Documentation/devicetree/bindings/sound/ics43432.txt
deleted file mode 100644
index e6f05f2f6c4e..000000000000
--- a/Documentation/devicetree/bindings/sound/ics43432.txt
+++ /dev/null
@@ -1,19 +0,0 @@
-Invensense ICS-43432-compatible MEMS microphone with I2S output.
-
-There are no software configuration options for this device, indeed, the only
-host connection is the I2S interface. Apart from requirements on clock
-frequency (460 kHz to 3.379 MHz according to the data sheet) there must be
-64 clock cycles in each stereo output frame; 24 of the 32 available bits
-contain audio data. A hardware pin determines if the device outputs data
-on the left or right channel of the I2S frame.
-
-Required properties:
- - compatible: should be one of the following.
- "invensense,ics43432": For the Invensense ICS43432
- "cui,cmm-4030d-261": For the CUI CMM-4030D-261-I2S-TR
-
-Example:
-
- ics43432: ics43432 {
- compatible = "invensense,ics43432";
- };
diff --git a/Documentation/devicetree/bindings/sound/invensense,ics43432.yaml b/Documentation/devicetree/bindings/sound/invensense,ics43432.yaml
new file mode 100644
index 000000000000..7bd984817aa9
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/invensense,ics43432.yaml
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/invensense,ics43432.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Invensense ICS-43432-compatible MEMS Microphone with I2S Output
+
+maintainers:
+ - Oleksij Rempel <o.rempel@pengutronix.de>
+
+description:
+ The ICS-43432 and compatible MEMS microphones output audio over an I2S
+ interface and require no software configuration. The only host connection
+ is the I2S bus. The microphone requires an I2S clock frequency between
+ 460 kHz and 3.379 MHz and 64 clock cycles per stereo frame. Each frame
+ contains 32-bit slots per channel, with 24 bits carrying audio data.
+ A hardware pin determines whether the microphone outputs audio on the
+ left or right channel of the I2S frame.
+
+allOf:
+ - $ref: dai-common.yaml#
+
+properties:
+ compatible:
+ enum:
+ - invensense,ics43432
+ - cui,cmm-4030d-261
+
+ port:
+ $ref: audio-graph-port.yaml#
+ unevaluatedProperties: false
+
+required:
+ - compatible
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ ics43432: ics43432 {
+ compatible = "invensense,ics43432";
+
+ port {
+ endpoint {
+ remote-endpoint = <&i2s1_endpoint>;
+ dai-format = "i2s";
+ };
+ };
+
+ };
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 6bf38f39724e..9b47a418f05b 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1204,6 +1204,8 @@ patternProperties:
description: Primux Trading, S.L.
"^probox2,.*":
description: PROBOX2 (by W2COMP Co., Ltd.)
+ "^pri,.*":
+ description: Priva
"^prt,.*":
description: Protonic Holland
"^pulsedlight,.*":
diff --git a/arch/arm/boot/dts/st/Makefile b/arch/arm/boot/dts/st/Makefile
index b7d5d305cbbe..60d55516f723 100644
--- a/arch/arm/boot/dts/st/Makefile
+++ b/arch/arm/boot/dts/st/Makefile
@@ -29,6 +29,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32h743i-eval.dtb \
stm32h743i-disco.dtb \
stm32h750i-art-pi.dtb \
+ stm32mp133c-prihmb.dtb \
stm32mp135f-dhcor-dhsbc.dtb \
stm32mp135f-dk.dtb \
stm32mp151a-prtt1a.dtb \
@@ -37,8 +38,11 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32mp151a-dhcor-testbench.dtb \
stm32mp151c-mecio1r0.dtb \
stm32mp151c-mect1s.dtb \
+ stm32mp151c-plyaqm.dtb \
stm32mp153c-dhcom-drc02.dtb \
stm32mp153c-dhcor-drc-compact.dtb \
+ stm32mp153c-lxa-fairytux2-gen1.dtb \
+ stm32mp153c-lxa-fairytux2-gen2.dtb \
stm32mp153c-lxa-tac-gen3.dtb \
stm32mp153c-mecio1r1.dtb \
stm32mp157a-avenger96.dtb \
diff --git a/arch/arm/boot/dts/st/stm32f746-disco.dts b/arch/arm/boot/dts/st/stm32f746-disco.dts
index 087de6f09629..b57dbdce2f40 100644
--- a/arch/arm/boot/dts/st/stm32f746-disco.dts
+++ b/arch/arm/boot/dts/st/stm32f746-disco.dts
@@ -78,6 +78,24 @@
serial0 = &usart1;
};
+ leds {
+ compatible = "gpio-leds";
+ led-usr {
+ gpios = <&gpioi 1 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ button-0 {
+ label = "User";
+ linux,code = <KEY_HOME>;
+ gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
usbotg_hs_phy: usb-phy {
#phy-cells = <0>;
compatible = "usb-nop-xceiv";
diff --git a/arch/arm/boot/dts/st/stm32f769-disco.dts b/arch/arm/boot/dts/st/stm32f769-disco.dts
index 52c5baf58ab9..535cfdc4681c 100644
--- a/arch/arm/boot/dts/st/stm32f769-disco.dts
+++ b/arch/arm/boot/dts/st/stm32f769-disco.dts
@@ -79,13 +79,16 @@
leds {
compatible = "gpio-leds";
- led-green {
+ led-usr2 {
gpios = <&gpioj 5 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
- led-red {
+ led-usr1 {
gpios = <&gpioj 13 GPIO_ACTIVE_HIGH>;
};
+ led-usr3 {
+ gpios = <&gpioa 12 GPIO_ACTIVE_HIGH>;
+ };
};
gpio-keys {
diff --git a/arch/arm/boot/dts/st/stm32mp131.dtsi b/arch/arm/boot/dts/st/stm32mp131.dtsi
index 0019d12c3d3d..8512a6e46b33 100644
--- a/arch/arm/boot/dts/st/stm32mp131.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp131.dtsi
@@ -100,6 +100,31 @@
always-on;
};
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&dts>;
+
+ trips {
+ cpu_alert1: cpu-alert1 {
+ temperature = <85000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ cpu-crit {
+ temperature = <120000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ };
+ };
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <1>;
@@ -919,6 +944,16 @@
};
};
+ dts: thermal@50028000 {
+ compatible = "st,stm32-thermal";
+ reg = <0x50028000 0x100>;
+ interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc DTS>;
+ clock-names = "pclk";
+ #thermal-sensor-cells = <0>;
+ status = "disabled";
+ };
+
mdma: dma-controller@58000000 {
compatible = "st,stm32h7-mdma";
reg = <0x58000000 0x1000>;
diff --git a/arch/arm/boot/dts/st/stm32mp133c-prihmb.dts b/arch/arm/boot/dts/st/stm32mp133c-prihmb.dts
new file mode 100644
index 000000000000..663b6de1b814
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp133c-prihmb.dts
@@ -0,0 +1,496 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/st,stm32mp13-regulator.h>
+#include "stm32mp133.dtsi"
+#include "stm32mp13xc.dtsi"
+#include "stm32mp13-pinctrl.dtsi"
+
+/ {
+ model = "Priva E-Measuringbox board";
+ compatible = "pri,prihmb", "st,stm32mp133";
+
+ aliases {
+ ethernet0 = &ethernet1;
+ mdio-gpio0 = &mdio0;
+ mmc0 = &sdmmc1;
+ mmc1 = &sdmmc2;
+ serial0 = &uart4;
+ serial1 = &usart6;
+ serial2 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ counter-0 {
+ compatible = "interrupt-counter";
+ gpios = <&gpioa 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ button-reset {
+ label = "reset-button";
+ linux,code = <BTN_1>;
+ gpios = <&gpioi 7 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-blue {
+ function = LED_FUNCTION_HEARTBEAT;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
+
+ led-controller-0 {
+ compatible = "pwm-leds-multicolor";
+
+ multi-led {
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_STATUS;
+ max-brightness = <255>;
+
+ led-red {
+ active-low;
+ color = <LED_COLOR_ID_RED>;
+ pwms = <&pwm2 2 1000000 1>;
+ };
+
+ led-green {
+ active-low;
+ color = <LED_COLOR_ID_GREEN>;
+ pwms = <&pwm1 1 1000000 1>;
+ };
+
+ led-blue {
+ active-low;
+ color = <LED_COLOR_ID_BLUE>;
+ pwms = <&pwm1 2 1000000 1>;
+ };
+ };
+ };
+
+ led-controller-1 {
+ compatible = "pwm-leds-multicolor";
+
+ multi-led {
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_STATUS;
+ max-brightness = <255>;
+
+ led-red {
+ active-low;
+ color = <LED_COLOR_ID_RED>;
+ pwms = <&pwm1 0 1000000 1>;
+ };
+
+ led-green {
+ active-low;
+ color = <LED_COLOR_ID_GREEN>;
+ pwms = <&pwm2 0 1000000 1>;
+ };
+
+ led-blue {
+ active-low;
+ color = <LED_COLOR_ID_BLUE>;
+ pwms = <&pwm2 1 1000000 1>;
+ };
+ };
+ };
+
+ /* DP83TD510E PHYs have max MDC rate of 1.75MHz. Since we can't reduce
+ * stmmac MDC clock without reducing system bus rate, we need to use
+ * gpio based MDIO bus.
+ */
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&gpiog 2 GPIO_ACTIVE_HIGH
+ &gpioa 2 GPIO_ACTIVE_HIGH>;
+
+ /* TI DP83TD510E */
+ phy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-id2000.0181";
+ reg = <0>;
+ interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10>;
+ reset-deassert-us = <35>;
+ };
+ };
+
+ memory@c0000000 {
+ device_type = "memory";
+ reg = <0xc0000000 0x10000000>;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ optee@ce000000 {
+ reg = <0xce000000 0x02000000>;
+ no-map;
+ };
+ };
+};
+
+&adc_1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&adc_1_pins_a>;
+ vdda-supply = <&reg_3v3>;
+ vref-supply = <&reg_3v3>;
+ status = "okay";
+};
+
+&adc1 {
+ status = "okay";
+
+ channel@0 { /* Fan current PC0*/
+ reg = <0>;
+ st,min-sample-time-ns = <10000>; /* 10µs sampling time */
+ };
+ channel@11 { /* Fan voltage */
+ reg = <11>;
+ st,min-sample-time-ns = <10000>; /* 10µs sampling time */
+ };
+ channel@15 { /* Supply voltage */
+ reg = <15>;
+ st,min-sample-time-ns = <10000>; /* 10µs sampling time */
+ };
+};
+
+&dts {
+ status = "okay";
+};
+
+&ethernet1 {
+ status = "okay";
+ pinctrl-0 = <&ethernet1_rmii_pins_a>;
+ pinctrl-1 = <&ethernet1_rmii_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rmii";
+ phy-handle = <&phy0>;
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_a>;
+ pinctrl-1 = <&i2c1_sleep_pins_a>;
+ clock-frequency = <100000>;
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+
+ board-sensor@48 {
+ compatible = "ti,tmp1075";
+ reg = <0x48>;
+ vs-supply = <&reg_3v3>;
+ };
+};
+
+&{i2c1_pins_a/pins} {
+ pinmux = <STM32_PINMUX('D', 3, AF5)>, /* I2C1_SCL */
+ <STM32_PINMUX('B', 8, AF4)>; /* I2C1_SDA */
+ bias-disable;
+ drive-open-drain;
+ slew-rate = <0>;
+};
+
+&{i2c1_sleep_pins_a/pins} {
+ pinmux = <STM32_PINMUX('D', 3, ANALOG)>, /* I2C1_SCL */
+ <STM32_PINMUX('B', 8, ANALOG)>; /* I2C1_SDA */
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+/* SD card without Card-detect */
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ broken-cd;
+ no-sdio;
+ no-1-8-v;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&reg_3v3>;
+ status = "okay";
+};
+
+/* EMMC */
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ no-1-8-v;
+ st,neg-edge;
+ mmc-ddr-3_3v;
+ bus-width = <8>;
+ vmmc-supply = <&reg_3v3>;
+ status = "okay";
+};
+
+&timers1 {
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pwm1: pwm {
+ pinctrl-0 = <&pwm1_pins_a>;
+ pinctrl-1 = <&pwm1_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+ };
+};
+
+&timers4 {
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pwm2: pwm {
+ pinctrl-0 = <&pwm4_pins_a>;
+ pinctrl-1 = <&pwm4_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+ };
+};
+
+/* Fan PWM */
+&timers5 {
+ status = "okay";
+
+ pwm3: pwm {
+ pinctrl-0 = <&pwm5_pins_a>;
+ pinctrl-1 = <&pwm5_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+ };
+};
+
+&timers2 {
+ status = "okay";
+
+ timer@1 {
+ status = "okay";
+ };
+};
+
+&uart4 {
+ pinctrl-names = "default", "sleep", "idle";
+ pinctrl-0 = <&uart4_pins_a>;
+ pinctrl-1 = <&uart4_sleep_pins_a>;
+ pinctrl-2 = <&uart4_idle_pins_a>;
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default", "sleep", "idle";
+ pinctrl-0 = <&uart7_pins_a>;
+ pinctrl-1 = <&uart7_sleep_pins_a>;
+ pinctrl-2 = <&uart7_idle_pins_a>;
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+};
+
+&usart6 {
+ pinctrl-names = "default", "sleep", "idle";
+ pinctrl-0 = <&usart6_pins_a>;
+ pinctrl-1 = <&usart6_sleep_pins_a>;
+ pinctrl-2 = <&usart6_idle_pins_a>;
+ linux,rs485-enabled-at-boot-time;
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+};
+
+&pinctrl {
+ adc_1_pins_a: adc1-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 0, ANALOG)>, /* ADC1 in0 */
+ <STM32_PINMUX('C', 2, ANALOG)>, /* ADC1 in15 */
+ <STM32_PINMUX('F', 13, ANALOG)>; /* ADC1 in11 */
+ };
+ };
+
+ ethernet1_rmii_pins_a: rmii-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+ <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+ <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+ <STM32_PINMUX('A', 1, AF11)>; /* ETH1_RMII_REF_CLK */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <2>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH1_RMII_RXD0 */
+ <STM32_PINMUX('C', 5, AF11)>, /* ETH1_RMII_RXD1 */
+ <STM32_PINMUX('A', 7, AF11)>; /* ETH1_RMII_CRS_DV */
+ bias-disable;
+ };
+ };
+
+ ethernet1_rmii_sleep_pins_a: rmii-sleep-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
+ <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
+ <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+ <STM32_PINMUX('C', 4, ANALOG)>, /* ETH1_RMII_RXD0 */
+ <STM32_PINMUX('C', 5, ANALOG)>, /* ETH1_RMII_RXD1 */
+ <STM32_PINMUX('A', 1, ANALOG)>, /* ETH1_RMII_REF_CLK */
+ <STM32_PINMUX('A', 7, ANALOG)>; /* ETH1_RMII_CRS_DV */
+ };
+ };
+
+ pwm1_pins_a: pwm1-0 {
+ pins {
+ pinmux = <STM32_PINMUX('E', 9, AF1)>, /* TIM1_CH1 */
+ <STM32_PINMUX('E', 11, AF1)>, /* TIM1_CH2 */
+ <STM32_PINMUX('E', 13, AF1)>; /* TIM1_CH3 */
+ bias-pull-down;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ };
+
+ pwm1_sleep_pins_a: pwm1-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('E', 9, ANALOG)>, /* TIM1_CH1 */
+ <STM32_PINMUX('E', 11, ANALOG)>, /* TIM1_CH2 */
+ <STM32_PINMUX('E', 13, ANALOG)>; /* TIM1_CH3 */
+ };
+ };
+
+ pwm4_pins_a: pwm4-0 {
+ pins {
+ pinmux = <STM32_PINMUX('D', 12, AF2)>, /* TIM4_CH1 */
+ <STM32_PINMUX('B', 7, AF2)>, /* TIM4_CH2 */
+ <STM32_PINMUX('D', 14, AF2)>; /* TIM4_CH3 */
+ bias-pull-down;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ };
+
+ pwm4_sleep_pins_a: pwm4-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* TIM4_CH1 */
+ <STM32_PINMUX('B', 7, ANALOG)>, /* TIM4_CH2 */
+ <STM32_PINMUX('D', 14, ANALOG)>; /* TIM4_CH3 */
+ };
+ };
+ pwm5_pins_a: pwm5-0 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 0, AF2)>; /* TIM5_CH1 */
+ };
+ };
+
+ pwm5_sleep_pins_a: pwm5-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 0, ANALOG)>; /* TIM5_CH1 */
+ };
+ };
+
+ uart7_pins_a: uart7-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART_TX */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('E', 10, AF7)>; /* UART7_RX */
+ bias-pull-up;
+ };
+ };
+
+ uart7_idle_pins_a: uart7-idle-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('E', 8, ANALOG)>; /* UART7_TX */
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('E', 10, AF7)>; /* UART7_RX */
+ bias-pull-up;
+ };
+ };
+
+ uart7_sleep_pins_a: uart7-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('E', 8, ANALOG)>, /* UART7_TX */
+ <STM32_PINMUX('E', 10, ANALOG)>; /* UART7_RX */
+ };
+ };
+
+ usart6_pins_a: usart6-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 8, AF7)>, /* USART6_TX */
+ <STM32_PINMUX('F', 10, AF7)>; /* USART6_DE */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('H', 11, AF7)>; /* USART6_RX */
+ bias-disable;
+ };
+ };
+
+ usart6_idle_pins_a: usart6-idle-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 8, ANALOG)>; /* USART6_TX */
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('F', 10, AF7)>; /* USART6_DE */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins3 {
+ pinmux = <STM32_PINMUX('H', 11, AF7)>; /* USART6_RX */
+ bias-disable;
+ };
+ };
+
+ usart6_sleep_pins_a: usart6-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('F', 8, ANALOG)>, /* USART6_TX */
+ <STM32_PINMUX('F', 10, ANALOG)>, /* USART6_DE */
+ <STM32_PINMUX('H', 11, ANALOG)>; /* USART6_RX */
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts b/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
index 853dc21449d9..9902849ed040 100644
--- a/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
+++ b/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
@@ -176,7 +176,7 @@
gpio-line-names = "", "", "", "",
"", "DHSBC_USB_PWR_CC1", "", "",
"", "", "", "DHSBC_nETH1_RST",
- "", "DHCOR_HW-CODING_0", "", "";
+ "", "DHCOR_HW-CODING_0", "", "DHSBC_HW-CODE_2";
};
&gpiob {
@@ -197,7 +197,7 @@
gpio-line-names = "", "", "", "",
"", "DHCOR_RAM-CODING_0", "", "",
"", "DHCOR_RAM-CODING_1", "", "",
- "", "", "", "";
+ "", "DHSBC_HW-CODE_1", "", "";
};
&gpioe {
@@ -221,6 +221,13 @@
"DHSBC_ETH1_INTB", "", "", "DHSBC_ETH2_INTB";
};
+&gpioh {
+ gpio-line-names = "", "", "", "DHSBC_HW-CODE_0",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "";
+};
+
&gpioi {
gpio-line-names = "DHCOR_RTC_nINT", "DHCOR_HW-CODING_1",
"DHCOR_BT_REG_ON", "DHCOR_PMIC_nINT",
@@ -296,6 +303,9 @@
st33htph: tpm@0 {
compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";
reg = <0>;
+ interrupt-parent = <&gpioe>;
+ interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpioe 12 GPIO_ACTIVE_LOW>;
spi-max-frequency = <24000000>;
};
};
@@ -419,3 +429,19 @@
type = "micro";
};
};
+
+/* LDO2 is expansion connector 3V3 supply on STM32MP13xx DHCOR DHSBC rev.200 */
+&vdd_ldo2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+};
+
+/* LDO5 is carrier board 3V3 supply on STM32MP13xx DHCOR DHSBC rev.200 */
+&vdd_sd {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi
index 95fafc51a1c8..40605ea85ee1 100644
--- a/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi
@@ -26,6 +26,13 @@
};
/omit-if-no-ref/
+ adc1_in10_pins_a: adc1-in10-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 0, ANALOG)>;
+ };
+ };
+
+ /omit-if-no-ref/
adc12_ain_pins_a: adc12-ain-0 {
pins {
pinmux = <STM32_PINMUX('C', 3, ANALOG)>, /* ADC1 in13 */
@@ -585,6 +592,43 @@
};
/omit-if-no-ref/
+ ethernet0_rmii_pins_d: rmii-3 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 12, AF11)>, /* ETH1_RMII_TXD0 */
+ <STM32_PINMUX('B', 13, AF11)>, /* ETH1_RMII_TXD1 */
+ <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+ <STM32_PINMUX('A', 1, AF11)>, /* ETH1_RMII_REF_CLK */
+ <STM32_PINMUX('A', 2, AF11)>, /* ETH1_MDIO */
+ <STM32_PINMUX('C', 1, AF11)>; /* ETH1_MDC */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <2>;
+ };
+
+ pins2 {
+ pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH1_RMII_RXD0 */
+ <STM32_PINMUX('C', 5, AF11)>, /* ETH1_RMII_RXD1 */
+ <STM32_PINMUX('A', 7, AF11)>; /* ETH1_RMII_CRS_DV */
+ bias-disable;
+ };
+ };
+
+ /omit-if-no-ref/
+ ethernet0_rmii_sleep_pins_d: rmii-sleep-3 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 12, ANALOG)>, /* ETH1_RMII_TXD0 */
+ <STM32_PINMUX('B', 13, ANALOG)>, /* ETH1_RMII_TXD1 */
+ <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+ <STM32_PINMUX('A', 2, ANALOG)>, /* ETH1_MDIO */
+ <STM32_PINMUX('C', 1, ANALOG)>, /* ETH1_MDC */
+ <STM32_PINMUX('C', 4, ANALOG)>, /* ETH1_RMII_RXD0 */
+ <STM32_PINMUX('C', 5, ANALOG)>, /* ETH1_RMII_RXD1 */
+ <STM32_PINMUX('A', 1, ANALOG)>, /* ETH1_RMII_REF_CLK */
+ <STM32_PINMUX('A', 7, ANALOG)>; /* ETH1_RMII_CRS_DV */
+ };
+ };
+
+ /omit-if-no-ref/
fmc_pins_a: fmc-0 {
pins1 {
pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
@@ -726,6 +770,25 @@
};
/omit-if-no-ref/
+ i2c1_pins_c: i2c1-2 {
+ pins {
+ pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+ <STM32_PINMUX('D', 13, AF5)>; /* I2C1_SDA */
+ bias-disable;
+ drive-open-drain;
+ slew-rate = <0>;
+ };
+ };
+
+ /omit-if-no-ref/
+ i2c1_sleep_pins_c: i2c1-sleep-2 {
+ pins {
+ pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
+ <STM32_PINMUX('D', 13, ANALOG)>; /* I2C1_SDA */
+ };
+ };
+
+ /omit-if-no-ref/
i2c2_pins_a: i2c2-0 {
pins {
pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */
@@ -820,6 +883,27 @@
};
/omit-if-no-ref/
+ i2s1_pins_a: i2s1-0 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 6, AF5)>, /* I2S2_SDI */
+ <STM32_PINMUX('A', 4, AF5)>, /* I2S2_WS */
+ <STM32_PINMUX('A', 5, AF5)>; /* I2S2_CK */
+ slew-rate = <0>;
+ drive-push-pull;
+ bias-disable;
+ };
+ };
+
+ /omit-if-no-ref/
+ i2s1_sleep_pins_a: i2s1-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 6, ANALOG)>, /* I2S2_SDI */
+ <STM32_PINMUX('A', 4, ANALOG)>, /* I2S2_WS */
+ <STM32_PINMUX('A', 5, ANALOG)>; /* I2S2_CK */
+ };
+ };
+
+ /omit-if-no-ref/
i2s2_pins_a: i2s2-0 {
pins {
pinmux = <STM32_PINMUX('I', 3, AF5)>, /* I2S2_SDO */
@@ -1419,6 +1503,23 @@
};
/omit-if-no-ref/
+ pwm1_pins_d: pwm1-3 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 0, AF2)>; /* TIM5_CH1 */
+ bias-pull-down;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ };
+
+ /omit-if-no-ref/
+ pwm1_sleep_pins_d: pwm1-sleep-3 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 0, ANALOG)>;
+ };
+ };
+
+ /omit-if-no-ref/
pwm2_pins_a: pwm2-0 {
pins {
pinmux = <STM32_PINMUX('A', 3, AF1)>; /* TIM2_CH4 */
@@ -2161,6 +2262,66 @@
};
/omit-if-no-ref/
+ sdmmc2_b4_pins_c: sdmmc2-b4-2 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+ <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+ <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+ <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+ <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+ slew-rate = <1>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+
+ pins2 {
+ pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+ slew-rate = <2>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ };
+
+ /omit-if-no-ref/
+ sdmmc2_b4_od_pins_c: sdmmc2-b4-od-2 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+ <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+ <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+ <STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
+ slew-rate = <1>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+
+ pins2 {
+ pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+ slew-rate = <2>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+
+ pins3 {
+ pinmux = <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+ slew-rate = <1>;
+ drive-open-drain;
+ bias-pull-up;
+ };
+ };
+
+ /omit-if-no-ref/
+ sdmmc2_b4_sleep_pins_c: sdmmc2-b4-sleep-2 {
+ pins {
+ pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
+ <STM32_PINMUX('B', 7, ANALOG)>, /* SDMMC2_D1 */
+ <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
+ <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
+ <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
+ <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
+ };
+ };
+
+ /omit-if-no-ref/
sdmmc2_d47_pins_a: sdmmc2-d47-0 {
pins {
pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
@@ -2390,6 +2551,66 @@
};
/omit-if-no-ref/
+ sdmmc3_b4_pins_c: sdmmc3-b4-2 {
+ pins1 {
+ pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+ <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+ <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+ <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
+ <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
+ slew-rate = <1>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+
+ pins2 {
+ pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+ slew-rate = <2>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ };
+
+ /omit-if-no-ref/
+ sdmmc3_b4_od_pins_c: sdmmc3-b4-od-2 {
+ pins1 {
+ pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+ <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+ <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+ <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
+ slew-rate = <1>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+
+ pins2 {
+ pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+ slew-rate = <2>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+
+ pins3 {
+ pinmux = <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
+ slew-rate = <1>;
+ drive-open-drain;
+ bias-pull-up;
+ };
+ };
+
+ /omit-if-no-ref/
+ sdmmc3_b4_sleep_pins_c: sdmmc3-b4-sleep-2 {
+ pins {
+ pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* SDMMC3_D0 */
+ <STM32_PINMUX('D', 4, ANALOG)>, /* SDMMC3_D1 */
+ <STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */
+ <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
+ <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
+ <STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */
+ };
+ };
+
+ /omit-if-no-ref/
spdifrx_pins_a: spdifrx-0 {
pins {
pinmux = <STM32_PINMUX('G', 12, AF8)>; /* SPDIF_IN1 */
@@ -2601,6 +2822,41 @@
};
/omit-if-no-ref/
+ uart4_pins_e: uart4-4 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 8, AF8)>; /* UART4_RX */
+ bias-disable;
+ };
+ };
+
+ /omit-if-no-ref/
+ uart4_idle_pins_e: uart4-idle-4 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 11, ANALOG)>; /* UART4_TX */
+ };
+
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 8, AF8)>; /* UART4_RX */
+ bias-disable;
+ };
+ };
+
+ /omit-if-no-ref/
+ uart4_sleep_pins_e: uart4-sleep-4 {
+ pins {
+ pinmux = <STM32_PINMUX('G', 11, ANALOG)>, /* UART4_TX */
+ <STM32_PINMUX('B', 8, ANALOG)>; /* UART4_RX */
+ };
+ };
+
+ /omit-if-no-ref/
uart5_pins_a: uart5-0 {
pins1 {
pinmux = <STM32_PINMUX('B', 13, AF14)>; /* UART5_TX */
@@ -2678,6 +2934,23 @@
};
/omit-if-no-ref/
+ uart7_pins_d: uart7-3 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 7, AF7)>, /* UART7_TX */
+ <STM32_PINMUX('F', 8, AF7)>; /* UART7_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+
+ pins2 {
+ pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART7_RX */
+ <STM32_PINMUX('F', 9, AF7)>; /* UART7_CTS */
+ bias-disable;
+ };
+ };
+
+ /omit-if-no-ref/
uart8_pins_a: uart8-0 {
pins1 {
pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */
@@ -3119,6 +3392,25 @@
};
/omit-if-no-ref/
+ i2c6_pins_b: i2c6-1 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 11, AF2)>, /* I2C6_SCL */
+ <STM32_PINMUX('A', 12, AF2)>; /* I2C6_SDA */
+ bias-disable;
+ drive-open-drain;
+ slew-rate = <0>;
+ };
+ };
+
+ /omit-if-no-ref/
+ i2c6_sleep_pins_b: i2c6-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 11, ANALOG)>, /* I2C6_SCL */
+ <STM32_PINMUX('A', 12, ANALOG)>; /* I2C6_SDA */
+ };
+ };
+
+ /omit-if-no-ref/
spi1_pins_a: spi1-0 {
pins1 {
pinmux = <STM32_PINMUX('Z', 0, AF5)>, /* SPI1_SCK */
diff --git a/arch/arm/boot/dts/st/stm32mp151c-plyaqm.dts b/arch/arm/boot/dts/st/stm32mp151c-plyaqm.dts
new file mode 100644
index 000000000000..39a3211c6133
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151c-plyaqm.dts
@@ -0,0 +1,376 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/dts-v1/;
+
+#include <arm/st/stm32mp151.dtsi>
+#include <arm/st/stm32mp15xc.dtsi>
+#include <arm/st/stm32mp15-pinctrl.dtsi>
+#include <arm/st/stm32mp15xxad-pinctrl.dtsi>
+#include <arm/st/stm32mp15-scmi.dtsi>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Plymovent AQM board";
+ compatible = "ply,plyaqm", "st,stm32mp151";
+
+ aliases {
+ ethernet0 = &ethernet0;
+ serial0 = &uart4;
+ serial1 = &uart7;
+ };
+
+ codec {
+ compatible = "invensense,ics43432";
+
+ port {
+ codec_endpoint: endpoint {
+ remote-endpoint = <&i2s1_endpoint>;
+ dai-format = "i2s";
+ };
+ };
+ };
+
+ firmware {
+ optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ gpios = <&gpioa 3 GPIO_ACTIVE_HIGH>; /* WHITE_EN */
+ color = <LED_COLOR_ID_WHITE>;
+ default-state = "on";
+ };
+ };
+
+ v3v3: fixed-regulator-v3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ v5v_sw: fixed-regulator-v5sw {
+ compatible = "regulator-fixed";
+ regulator-name = "5v-switched";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpioe 10 GPIO_ACTIVE_HIGH>; /* 5V_SWITCHED_EN */
+ startup-delay-us = <100000>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ optee@cfd00000 {
+ reg = <0xcfd00000 0x300000>;
+ no-map;
+ };
+ };
+
+ sound {
+ compatible = "audio-graph-card";
+ label = "STM32MP15";
+ dais = <&i2s1_port>;
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpioe 12 GPIO_ACTIVE_LOW>; /* WLAN_REG_ON */
+ };
+};
+
+&adc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&adc1_in10_pins_a>;
+ vdda-supply = <&v3v3>;
+ vref-supply = <&v3v3>;
+ status = "okay";
+
+ adc@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ channel@10 { /* NTC */
+ reg = <10>;
+ st,min-sample-time-ns = <10000>; /* 10µs sampling time */
+ };
+ };
+};
+
+&cpu0 {
+ clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cryp1 {
+ clocks = <&scmi_clk CK_SCMI_CRYP1>;
+ resets = <&scmi_reset RST_SCMI_CRYP1>;
+ status = "okay";
+};
+
+&ethernet0 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&ethernet0_rmii_pins_d>;
+ pinctrl-1 = <&ethernet0_rmii_sleep_pins_d>;
+ phy-mode = "rmii";
+ max-speed = <100>;
+ phy-handle = <&ethphy0>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+
+ /* KSZ8081RNA PHY */
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpiob 0 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpiob 1 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&gpioa {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "HWID_PL_N", "HWID_CP", "";
+};
+
+&gpiob {
+ gpio-line-names =
+ "", "", "", "", "", "", "LED_LATCH", "",
+ "", "RELAY1_EN", "", "", "", "", "", "";
+};
+
+&gpioc {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "HWID_Q7", "", "";
+};
+
+&gpioe {
+ gpio-line-names =
+ "", "", "", "", "RELAY2_EN", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpiog {
+ gpio-line-names =
+ "", "", "", "", "", "", "", "SW1",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpioz {
+ clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+ clocks = <&scmi_clk CK_SCMI_HASH1>;
+ resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_c>;
+ pinctrl-1 = <&i2c1_sleep_pins_c>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&i2c4 {
+ clocks = <&scmi_clk CK_SCMI_I2C4>;
+ resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&i2c6 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c6_pins_b>;
+ pinctrl-1 = <&i2c6_sleep_pins_b>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ clocks = <&scmi_clk CK_SCMI_I2C6>;
+ resets = <&scmi_reset RST_SCMI_I2C6>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pressure-sensor@47 {
+ compatible = "bosch,bmp580";
+ reg = <0x47>;
+ vdda-supply = <&v5v_sw>;
+ vddd-supply = <&v5v_sw>;
+ };
+
+ co2-sensor@62 {
+ compatible = "sensirion,scd41";
+ reg = <0x62>;
+ vdd-supply = <&v5v_sw>;
+ };
+
+ pm-sensor@69 {
+ compatible = "sensirion,sps30";
+ reg = <0x69>;
+ };
+};
+
+&i2s1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2s1_pins_a>;
+ pinctrl-1 = <&i2s1_sleep_pins_a>;
+ clocks = <&rcc SPI1>, <&rcc SPI1_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+ clock-names = "pclk", "i2sclk", "x8k", "x11k";
+ #clock-cells = <0>; /* Set I2S2 as master clock provider */
+ status = "okay";
+
+ i2s1_port: port {
+ i2s1_endpoint: endpoint {
+ format = "i2s";
+ mclk-fs = <256>;
+ remote-endpoint = <&codec_endpoint>;
+ };
+ };
+};
+
+&iwdg2 {
+ clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+ status = "okay";
+};
+
+&m4_rproc {
+ /delete-property/ st,syscfg-holdboot;
+ resets = <&scmi_reset RST_SCMI_MCU>,
+ <&scmi_reset RST_SCMI_MCU_HOLD_BOOT>;
+ reset-names = "mcu_rst", "hold_boot";
+};
+
+&mdma1 {
+ resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&rcc {
+ compatible = "st,stm32mp1-rcc-secure", "syscon";
+ clock-names = "hse", "hsi", "csi", "lse", "lsi";
+ clocks = <&scmi_clk CK_SCMI_HSE>,
+ <&scmi_clk CK_SCMI_HSI>,
+ <&scmi_clk CK_SCMI_CSI>,
+ <&scmi_clk CK_SCMI_LSE>,
+ <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+ clocks = <&scmi_clk CK_SCMI_RNG1>;
+ resets = <&scmi_reset RST_SCMI_RNG1>;
+ status = "okay";
+};
+
+&rtc {
+ clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
+
+/* SD card without Card-detect */
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ broken-cd;
+ no-sdio;
+ no-1-8-v;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+/* EMMC */
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_c &sdmmc2_d47_pins_b>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_c &sdmmc2_d47_pins_b>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_c &sdmmc2_d47_sleep_pins_b>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ no-1-8-v;
+ st,neg-edge;
+ bus-width = <8>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+/* Wifi */
+&sdmmc3 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc3_b4_pins_c>;
+ pinctrl-1 = <&sdmmc3_b4_od_pins_c>;
+ pinctrl-2 = <&sdmmc3_b4_sleep_pins_c>;
+ non-removable;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+&timers5 {
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pwm {
+ pinctrl-0 = <&pwm1_pins_d>;
+ pinctrl-1 = <&pwm1_sleep_pins_d>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+ };
+};
+
+&uart4 {
+ pinctrl-names = "default", "sleep", "idle";
+ pinctrl-0 = <&uart4_pins_e>;
+ pinctrl-1 = <&uart4_idle_pins_e>;
+ pinctrl-2 = <&uart4_sleep_pins_e>;
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_d>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpioe 11 GPIO_ACTIVE_HIGH>; /* BT_REG_ON */
+ max-speed = <4000000>;
+ vbat-supply = <&v3v3>;
+ vddio-supply = <&v3v3>;
+ interrupt-parent = <&gpiog>;
+ interrupts = <12 IRQ_TYPE_EDGE_RISING>; /* BT_HOST_WAKE */
+ interrupt-names = "host-wakeup";
+ };
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen1.dts b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen1.dts
new file mode 100644
index 000000000000..3a0e84262424
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen1.dts
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2024 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp153c-lxa-fairytux2.dtsi"
+
+/ {
+ model = "Linux Automation GmbH FairyTux 2 Gen 1";
+ compatible = "lxa,stm32mp153c-fairytux2-gen1", "oct,stm32mp153x-osd32", "st,stm32mp153";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-left {
+ label = "USER_BTN1";
+ linux,code = <KEY_ESC>;
+ gpios = <&gpioi 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ };
+
+ button-right {
+ label = "USER_BTN2";
+ linux,code = <KEY_HOME>;
+ gpios = <&gpioe 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ };
+ };
+};
+
+&gpiof {
+ gpio-line-names = "GPIO1", "GPIO2", "", "", "", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "", "", "", "", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpioh {
+ gpio-line-names = "", "", "", "", "LCD_RESET", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "", "", "", "GPIO3", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpioi {
+ gpio-line-names = "", "", "", "", "", /* 0 */
+ "", "", "", "ETH_", "", /* 5 */
+ "", "USER_BTN1"; /* 10 */
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_b>;
+ pinctrl-1 = <&i2c1_sleep_pins_b>;
+ status = "okay";
+
+ io_board_gpio: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <&v3v3_hdmi>;
+ gpio-line-names = "LED1_GA_YK", "LED2_GA_YK", "LED1_GK_YA", "LED2_GK_YA",
+ "RS485_EN", "RS485_120R", "", "CAN_120R";
+ };
+};
+
+&led_controller_io {
+ /*
+ * led-2 and led-3 are internally connected antiparallel to one
+ * another inside the ethernet jack like this:
+ * GPIO1 ---+---|led-2|>--+--- GPIO3
+ * +--<|led-3|---+
+ * E.g. only one of the LEDs can be illuminated at a time while
+ * the other output must be driven low.
+ * This should likely be implemented using a multi color LED
+ * driver for antiparallel LEDs.
+ */
+ led-2 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_ACTIVITY;
+ gpios = <&io_board_gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-3 {
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_ACTIVITY;
+ gpios = <&io_board_gpio 3 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&usart3 {
+ /*
+ * On Gen 1 FairyTux 2 only RTS can be used and not CTS as well,
+ * Because pins PD11 (CTS) and PI11 (USER_BTN1) share the same
+ * interrupt and only one of them can be used at a time.
+ */
+ rts-gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
+};
+
+&usbotg_hs {
+ dr_mode = "peripheral";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen2.dts b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen2.dts
new file mode 100644
index 000000000000..66e6da912508
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen2.dts
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2024 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp153c-lxa-fairytux2.dtsi"
+
+/ {
+ model = "Linux Automation GmbH FairyTux 2 Gen 2";
+ compatible = "lxa,stm32mp153c-fairytux2-gen2", "oct,stm32mp153x-osd32", "st,stm32mp153";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-left {
+ label = "USER_BTN1";
+ linux,code = <KEY_ESC>;
+ gpios = <&gpioi 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ };
+
+ button-right {
+ label = "USER_BTN2";
+ linux,code = <KEY_HOME>;
+ gpios = <&gpioe 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ };
+ };
+};
+
+&gpiof {
+ gpio-line-names = "", "", "", "", "", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "", "", "", "", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpioh {
+ gpio-line-names = "", "", "", "", "LCD_RESET", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "", "", "GPIO1", "GPIO_INT", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpioi {
+ gpio-line-names = "GPIO2", "", "", "", "", /* 0 */
+ "", "", "", "ETH_", "", /* 5 */
+ "", "USER_BTN1"; /* 10 */
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_b>;
+ pinctrl-1 = <&i2c1_sleep_pins_b>;
+ status = "okay";
+
+ io_board_gpio: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&gpioh>;
+ interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&board_tca6408_pins>;
+ #interrupt-cells = <2>;
+ vcc-supply = <&v3v3_hdmi>;
+ gpio-line-names = "LED1_GA_YK", "LED2_GA_YK", "LED1_GK_YA", "USB_CC_ALERT",
+ "RS485_EN", "RS485_120R", "USB_CC_RESET", "CAN_120R";
+ };
+
+ usb_c: typec@28 {
+ compatible = "st,stusb1600";
+ reg = <0x28>;
+ interrupt-parent = <&io_board_gpio>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&reg_5v>;
+ vsys-supply = <&v3v3_hdmi>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ typec-power-opmode = "default";
+
+ port {
+ con_usbotg_hs_ep: endpoint {
+ remote-endpoint = <&usbotg_hs_ep>;
+ };
+ };
+ };
+ };
+
+ temperature-sensor@48 {
+ compatible = "national,lm75a";
+ reg = <0x48>;
+ /*
+ * The sensor itself is powered by a voltage divider from the
+ * always-on 5V supply.
+ * The required pull-up resistors however are on v3v3_hdmi.
+ */
+ vs-supply = <&v3v3_hdmi>;
+ };
+
+ io_board_eeprom: eeprom@56 {
+ compatible = "atmel,24c04";
+ reg = <0x56>;
+ vcc-supply = <&v3v3_hdmi>;
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&led_controller_io {
+ led-2 {
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_ACTIVITY;
+ gpios = <&io_board_gpio 1 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&usart3 {
+ rts-gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
+ cts-gpios = <&gpiod 11 GPIO_ACTIVE_LOW>;
+};
+
+&usbotg_hs {
+ usb-role-switch;
+
+ port {
+ usbotg_hs_ep: endpoint {
+ remote-endpoint = <&con_usbotg_hs_ep>;
+ };
+ };
+};
+
+&pinctrl {
+ board_tca6408_pins: stusb1600-0 {
+ pins {
+ pinmux = <STM32_PINMUX('H', 13, GPIO)>;
+ bias-pull-up;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2.dtsi b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2.dtsi
new file mode 100644
index 000000000000..9eeb9d6b5eb0
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2.dtsi
@@ -0,0 +1,397 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023, 2024 Leonard Göhrs, Pengutronix
+ */
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-osd32.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ aliases {
+ can0 = &m_can1;
+ ethernet0 = &ethernet0;
+ i2c0 = &i2c1;
+ i2c1 = &i2c4;
+ mmc1 = &sdmmc2;
+ serial0 = &uart4;
+ serial1 = &usart3;
+ spi0 = &spi4;
+ };
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ power-supply = <&v3v3>;
+
+ brightness-levels = <0 31 63 95 127 159 191 223 255>;
+ default-brightness-level = <7>;
+ pwms = <&led_pwm 3 1000000 0>;
+ };
+
+ led-controller-cpu {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_HEARTBEAT;
+ gpios = <&gpioa 13 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ led_controller_io: led-controller-io {
+ compatible = "gpio-leds";
+
+ /*
+ * led-0 and led-1 are internally connected antiparallel to one
+ * another inside the ethernet jack like this:
+ * GPIO0 ---+---|led-0|>--+--- GPIO2
+ * +--<|led-1|---+
+ * E.g. only one of the LEDs can be illuminated at a time while
+ * the other output must be driven low.
+ * This should likely be implemented using a multi color LED
+ * driver for antiparallel LEDs.
+ */
+ led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ gpios = <&io_board_gpio 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-1 {
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_LAN;
+ gpios = <&io_board_gpio 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_1v2: regulator-1v2 {
+ compatible = "regulator-fixed";
+ regulator-name = "1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ vin-supply = <&reg_5v>;
+ };
+};
+
+baseboard_eeprom: &sip_eeprom {
+};
+
+&crc1 {
+ status = "okay";
+};
+
+&cryp1 {
+ status = "okay";
+};
+
+&dts {
+ status = "okay";
+};
+
+&ethernet0 {
+ assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>;
+ assigned-clock-parents = <&rcc PLL4_P>;
+ assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF */
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&ethernet0_rgmii_pins_b>;
+ pinctrl-1 = <&ethernet0_rgmii_sleep_pins_b>;
+
+ st,eth-clk-sel;
+ phy-mode = "rgmii-id";
+ phy-handle = <&ethphy>;
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@3 { /* KSZ9031RN */
+ reg = <3>;
+ reset-gpios = <&gpioe 11 GPIO_ACTIVE_LOW>; /* ETH_RST# */
+ interrupt-parent = <&gpioa>;
+ interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ micrel,force-master;
+ };
+ };
+};
+
+&gpioa {
+ gpio-line-names = "", "", "", "", "", /* 0 */
+ "", "ETH_INT", "", "", "", /* 5 */
+ "", "", "", "BOOTROM_LED", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpiob {
+ gpio-line-names = "", "", "", "", "", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "", "", "", "", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpioc {
+ gpio-line-names = "", "", "", "", "", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "", ""; /* 10 */
+};
+
+&gpiod {
+ gpio-line-names = "", "", "", "", "", /* 0 */
+ "", "", "LCD_TE", "", "", /* 5 */
+ "LCD_DC", "", "", "", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpioe {
+ gpio-line-names = "LCD_CS", "", "", "", "", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "", "", "", "", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpiof {
+ gpio-line-names = "GPIO1", "GPIO2", "", "", "", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "", "", "", "", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpiog {
+ gpio-line-names = "", "", "", "", "", /* 0 */
+ "", "", "", "", "", /* 5 */
+ "", "", "", "", "", /* 10 */
+ ""; /* 15 */
+};
+
+&gpioz {
+ gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", /* 0 */
+ "", "HWID4", "HWID5"; /* 5 */
+};
+
+&hash1 {
+ status = "okay";
+};
+
+&iwdg2 {
+ timeout-sec = <8>;
+ status = "okay";
+};
+
+&m_can1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&m_can1_pins_b>;
+ pinctrl-1 = <&m_can1_sleep_pins_b>;
+ status = "okay";
+ termination-gpios = <&io_board_gpio 7 GPIO_ACTIVE_HIGH>;
+ termination-ohms = <120>;
+};
+
+&pmic {
+ regulators {
+ buck1-supply = <&reg_5v>; /* VIN */
+ buck2-supply = <&reg_5v>; /* VIN */
+ buck3-supply = <&reg_5v>; /* VIN */
+ buck4-supply = <&reg_5v>; /* VIN */
+ ldo2-supply = <&reg_5v>; /* PMIC_LDO25IN */
+ ldo4-supply = <&reg_5v>; /* VIN */
+ ldo5-supply = <&reg_5v>; /* PMIC_LDO25IN */
+ vref_ddr-supply = <&reg_5v>; /* VIN */
+ boost-supply = <&reg_5v>; /* PMIC_BSTIN */
+ pwr_sw2-supply = <&bst_out>; /* PMIC_SWIN */
+ };
+};
+
+&pwr_regulators {
+ vdd-supply = <&vdd>;
+ vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
+ vmmc-supply = <&v3v3>;
+
+ bus-width = <8>;
+ mmc-ddr-3_3v;
+ no-1-8-v;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,neg-edge;
+
+ status = "okay";
+};
+
+&spi4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi4_pins_a>;
+ cs-gpios = <&gpioe 0 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ lcd: display@0 {
+ compatible = "shineworld,lh133k", "panel-mipi-dbi-spi";
+ reg = <0>;
+ power-supply = <&v3v3>;
+ io-supply = <&v3v3>;
+ backlight = <&backlight>;
+ dc-gpios = <&gpiod 10 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpioh 4 GPIO_ACTIVE_HIGH>;
+ spi-3wire;
+ spi-max-frequency = <32000000>;
+
+ width-mm = <23>;
+ height-mm = <23>;
+ rotation = <180>;
+
+ panel-timing {
+ hactive = <240>;
+ vactive = <240>;
+ hback-porch = <0>;
+ vback-porch = <0>;
+
+ clock-frequency = <0>;
+ hfront-porch = <0>;
+ hsync-len = <0>;
+ vfront-porch = <0>;
+ vsync-len = <0>;
+ };
+ };
+};
+
+&timers2 {
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+
+ timer@1 {
+ status = "okay";
+ };
+};
+
+&timers3 {
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+
+ timer@2 {
+ status = "okay";
+ };
+};
+
+&timers4 {
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+
+ timer@3 {
+ status = "okay";
+ };
+};
+
+&timers8 {
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+
+ led_pwm: pwm {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pwm8_pins_b>;
+ pinctrl-1 = <&pwm8_sleep_pins_b>;
+ status = "okay";
+ };
+};
+
+&uart4 {
+ label = "debug";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+};
+
+&usart3 {
+ label = "external";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&usart3_pins_a>;
+
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ status = "okay";
+};
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>;
+ phy-names = "usb";
+
+ status = "okay";
+};
+
+&usbotg_hs {
+ phys = <&usbphyc_port1 0>;
+ phy-names = "usb2-phy";
+
+ vusb_d-supply = <&vdd_usb>;
+ vusb_a-supply = <&reg18>;
+
+ status = "okay";
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port0 {
+ phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+ phy-supply = <&vdd_usb>;
+};
+
+&v3v3_hdmi {
+ regulator-enable-ramp-delay = <1000>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-dk2.dts b/arch/arm/boot/dts/st/stm32mp157c-dk2.dts
index 5f9c0160a9c4..324f7bb988d1 100644
--- a/arch/arm/boot/dts/st/stm32mp157c-dk2.dts
+++ b/arch/arm/boot/dts/st/stm32mp157c-dk2.dts
@@ -67,7 +67,7 @@
touchscreen@38 {
compatible = "focaltech,ft6236";
reg = <0x38>;
- interrupts = <2 2>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
interrupt-parent = <&gpiof>;
touchscreen-size-x = <480>;
touchscreen-size-y = <800>;
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index c468c23b2bba..8b76821f190f 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -321,6 +321,10 @@ config ARCH_STM32
help
This enables support for ARMv8 based STMicroelectronics
STM32 family, including:
+ - STM32MP21:
+ - STM32MP211, STM32MP213, STM32MP215.
+ - STM32MP23:
+ - STM32MP231, STM32MP233, STM32MP235.
- STM32MP25:
- STM32MP251, STM32MP253, STM32MP255 and STM32MP257.
diff --git a/arch/arm64/boot/dts/st/Makefile b/arch/arm64/boot/dts/st/Makefile
index 881fe1296c58..63908113ae36 100644
--- a/arch/arm64/boot/dts/st/Makefile
+++ b/arch/arm64/boot/dts/st/Makefile
@@ -1,2 +1,6 @@
# SPDX-License-Identifier: GPL-2.0-only
-dtb-$(CONFIG_ARCH_STM32) += stm32mp257f-ev1.dtb
+dtb-$(CONFIG_ARCH_STM32) += \
+ stm32mp215f-dk.dtb \
+ stm32mp235f-dk.dtb \
+ stm32mp257f-dk.dtb \
+ stm32mp257f-ev1.dtb
diff --git a/arch/arm64/boot/dts/st/stm32mp211.dtsi b/arch/arm64/boot/dts/st/stm32mp211.dtsi
new file mode 100644
index 000000000000..6dd1377f3e1d
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp211.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a35";
+ reg = <0>;
+ device_type = "cpu";
+ enable-method = "psci";
+ };
+ };
+
+ arm-pmu {
+ compatible = "arm,cortex-a35-pmu";
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>;
+ interrupt-parent = <&intc>;
+ };
+
+ arm_wdt: watchdog {
+ compatible = "arm,smc-wdt";
+ arm,smc-id = <0xbc000000>;
+ status = "disabled";
+ };
+
+ ck_flexgen_08: clock-64000000 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <64000000>;
+ };
+
+ ck_flexgen_51: clock-200000000 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <200000000>;
+ };
+
+ firmware {
+ optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ };
+
+ scmi: scmi {
+ compatible = "linaro,scmi-optee";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ linaro,optee-channel-id = <0>;
+
+ scmi_clk: protocol@14 {
+ reg = <0x14>;
+ #clock-cells = <1>;
+ };
+
+ scmi_reset: protocol@16 {
+ reg = <0x16>;
+ #reset-cells = <1>;
+ };
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&intc>;
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+ arm,no-tick-in-suspend;
+ };
+
+ soc@0 {
+ compatible = "simple-bus";
+ ranges = <0x0 0x0 0x0 0x0 0x80000000>;
+ dma-ranges = <0x0 0x0 0x80000000 0x1 0x0>;
+ interrupt-parent = <&intc>;
+ #address-cells = <1>;
+ #size-cells = <2>;
+
+ rifsc: bus@42080000 {
+ compatible = "simple-bus";
+ reg = <0x42080000 0x0 0x1000>;
+ ranges;
+ dma-ranges;
+ #address-cells = <1>;
+ #size-cells = <2>;
+
+ usart2: serial@400e0000 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x400e0000 0x0 0x400>;
+ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ck_flexgen_08>;
+ status = "disabled";
+ };
+ };
+
+ syscfg: syscon@44230000 {
+ compatible = "st,stm32mp21-syscfg", "syscon";
+ reg = <0x44230000 0x0 0x10000>;
+ };
+
+ intc: interrupt-controller@4ac10000 {
+ compatible = "arm,cortex-a7-gic";
+ reg = <0x4ac10000 0x0 0x1000>,
+ <0x4ac20000 0x0 0x2000>,
+ <0x4ac40000 0x0 0x2000>,
+ <0x4ac60000 0x0 0x2000>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp213.dtsi b/arch/arm64/boot/dts/st/stm32mp213.dtsi
new file mode 100644
index 000000000000..fdd2dc432edd
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp213.dtsi
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp211.dtsi"
+
+/ {
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp215.dtsi b/arch/arm64/boot/dts/st/stm32mp215.dtsi
new file mode 100644
index 000000000000..a7df77f928c5
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp215.dtsi
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp213.dtsi"
+
+/ {
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp215f-dk.dts b/arch/arm64/boot/dts/st/stm32mp215f-dk.dts
new file mode 100644
index 000000000000..7bdaeaa5ab0f
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp215f-dk.dts
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Amelie Delaunay <amelie.delaunay@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp215.dtsi"
+#include "stm32mp21xf.dtsi"
+
+/ {
+ model = "STMicroelectronics STM32MP215F-DK Discovery Board";
+ compatible = "st,stm32mp215f-dk", "st,stm32mp215";
+
+ aliases {
+ serial0 = &usart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0x0 0x80000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ fw@80000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x80000000 0x0 0x4000000>;
+ no-map;
+ };
+ };
+};
+
+&arm_wdt {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&usart2 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp21xc.dtsi b/arch/arm64/boot/dts/st/stm32mp21xc.dtsi
new file mode 100644
index 000000000000..e33b00b424e1
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp21xc.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp21xf.dtsi b/arch/arm64/boot/dts/st/stm32mp21xf.dtsi
new file mode 100644
index 000000000000..e33b00b424e1
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp21xf.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp231.dtsi b/arch/arm64/boot/dts/st/stm32mp231.dtsi
new file mode 100644
index 000000000000..8820d219a33e
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp231.dtsi
@@ -0,0 +1,1214 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/clock/st,stm32mp25-rcc.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/st,stm32mp25-regulator.h>
+#include <dt-bindings/reset/st,stm32mp25-rcc.h>
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a35";
+ reg = <0>;
+ device_type = "cpu";
+ enable-method = "psci";
+ power-domains = <&cpu0_pd>;
+ power-domain-names = "psci";
+ };
+ };
+
+ arm-pmu {
+ compatible = "arm,cortex-a35-pmu";
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>;
+ interrupt-parent = <&intc>;
+ };
+
+ arm_wdt: watchdog {
+ compatible = "arm,smc-wdt";
+ arm,smc-id = <0xb200005a>;
+ status = "disabled";
+ };
+
+ clk_dsi_txbyte: clock-0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ clk_rcbsec: clk-64000000 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <64000000>;
+ };
+
+ firmware {
+ optee: optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ interrupt-parent = <&intc>;
+ interrupts = <GIC_PPI 15 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ scmi {
+ compatible = "linaro,scmi-optee";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ linaro,optee-channel-id = <0>;
+
+ scmi_clk: protocol@14 {
+ reg = <0x14>;
+ #clock-cells = <1>;
+ };
+
+ scmi_reset: protocol@16 {
+ reg = <0x16>;
+ #reset-cells = <1>;
+ };
+
+ scmi_voltd: protocol@17 {
+ reg = <0x17>;
+
+ scmi_regu: regulators {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ scmi_vddio1: regulator@0 {
+ reg = <VOLTD_SCMI_VDDIO1>;
+ regulator-name = "vddio1";
+ };
+ scmi_vddio2: regulator@1 {
+ reg = <VOLTD_SCMI_VDDIO2>;
+ regulator-name = "vddio2";
+ };
+ scmi_vddio3: regulator@2 {
+ reg = <VOLTD_SCMI_VDDIO3>;
+ regulator-name = "vddio3";
+ };
+ scmi_vddio4: regulator@3 {
+ reg = <VOLTD_SCMI_VDDIO4>;
+ regulator-name = "vddio4";
+ };
+ scmi_vdd33ucpd: regulator@5 {
+ reg = <VOLTD_SCMI_UCPD>;
+ regulator-name = "vdd33ucpd";
+ };
+ scmi_vdda18adc: regulator@7 {
+ reg = <VOLTD_SCMI_ADC>;
+ regulator-name = "vdda18adc";
+ };
+ };
+ };
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+
+ cpu0_pd: power-domain-cpu0 {
+ #power-domain-cells = <0>;
+ power-domains = <&cluster_pd>;
+ };
+
+ cluster_pd: power-domain-cluster {
+ #power-domain-cells = <0>;
+ power-domains = <&ret_pd>;
+ };
+
+ ret_pd: power-domain-retention {
+ #power-domain-cells = <0>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&intc>;
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+ always-on;
+ };
+
+ soc@0 {
+ compatible = "simple-bus";
+ ranges = <0x0 0x0 0x0 0x80000000>;
+ interrupt-parent = <&intc>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ hpdma: dma-controller@40400000 {
+ compatible = "st,stm32mp25-dma3";
+ reg = <0x40400000 0x1000>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk CK_SCMI_HPDMA1>;
+ #dma-cells = <3>;
+ };
+
+ hpdma2: dma-controller@40410000 {
+ compatible = "st,stm32mp25-dma3";
+ reg = <0x40410000 0x1000>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk CK_SCMI_HPDMA2>;
+ #dma-cells = <3>;
+ };
+
+ hpdma3: dma-controller@40420000 {
+ compatible = "st,stm32mp25-dma3";
+ reg = <0x40420000 0x1000>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk CK_SCMI_HPDMA3>;
+ #dma-cells = <3>;
+ };
+
+ rifsc: bus@42080000 {
+ compatible = "st,stm32mp25-rifsc", "simple-bus";
+ reg = <0x42080000 0x1000>;
+ ranges;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #access-controller-cells = <1>;
+
+ i2s2: audio-controller@400b0000 {
+ compatible = "st,stm32mp25-i2s";
+ reg = <0x400b0000 0x400>;
+ #sound-dai-cells = <0>;
+ interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_BUS_SPI2>, <&rcc CK_KER_SPI2>;
+ clock-names = "pclk", "i2sclk";
+ resets = <&rcc SPI2_R>;
+ dmas = <&hpdma 51 0x43 0x12>,
+ <&hpdma 52 0x43 0x21>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 23>;
+ status = "disabled";
+ };
+
+ spi2: spi@400b0000 {
+ compatible = "st,stm32mp25-spi";
+ reg = <0x400b0000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_SPI2>;
+ resets = <&rcc SPI2_R>;
+ dmas = <&hpdma 51 0x20 0x3012>,
+ <&hpdma 52 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 23>;
+ status = "disabled";
+ };
+
+ i2s3: audio-controller@400c0000 {
+ compatible = "st,stm32mp25-i2s";
+ reg = <0x400c0000 0x400>;
+ #sound-dai-cells = <0>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_BUS_SPI3>, <&rcc CK_KER_SPI3>;
+ clock-names = "pclk", "i2sclk";
+ resets = <&rcc SPI3_R>;
+ dmas = <&hpdma 53 0x43 0x12>,
+ <&hpdma 54 0x43 0x21>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 24>;
+ status = "disabled";
+ };
+
+ spi3: spi@400c0000 {
+ compatible = "st,stm32mp25-spi";
+ reg = <0x400c0000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_SPI3>;
+ resets = <&rcc SPI3_R>;
+ dmas = <&hpdma 53 0x20 0x3012>,
+ <&hpdma 54 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 24>;
+ status = "disabled";
+ };
+
+ spdifrx: audio-controller@400d0000 {
+ compatible = "st,stm32h7-spdifrx";
+ reg = <0x400d0000 0x400>;
+ #sound-dai-cells = <0>;
+ clocks = <&rcc CK_KER_SPDIFRX>;
+ clock-names = "kclk";
+ interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&hpdma 71 0x43 0x212>,
+ <&hpdma 72 0x43 0x212>;
+ dma-names = "rx", "rx-ctrl";
+ access-controllers = <&rifsc 30>;
+ status = "disabled";
+ };
+
+ usart2: serial@400e0000 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x400e0000 0x400>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_USART2>;
+ dmas = <&hpdma 11 0x20 0x10012>,
+ <&hpdma 12 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 32>;
+ status = "disabled";
+ };
+
+ usart3: serial@400f0000 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x400f0000 0x400>;
+ interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_USART3>;
+ dmas = <&hpdma 13 0x20 0x10012>,
+ <&hpdma 14 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 33>;
+ status = "disabled";
+ };
+
+ uart4: serial@40100000 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x40100000 0x400>;
+ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_UART4>;
+ dmas = <&hpdma 15 0x20 0x10012>,
+ <&hpdma 16 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 34>;
+ status = "disabled";
+ };
+
+ uart5: serial@40110000 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x40110000 0x400>;
+ interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_UART5>;
+ dmas = <&hpdma 17 0x20 0x10012>,
+ <&hpdma 18 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 35>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@40120000 {
+ compatible = "st,stm32mp25-i2c";
+ reg = <0x40120000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-names = "event";
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_I2C1>;
+ resets = <&rcc I2C1_R>;
+ dmas = <&hpdma 27 0x20 0x3012>,
+ <&hpdma 28 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 41>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@40130000 {
+ compatible = "st,stm32mp25-i2c";
+ reg = <0x40130000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-names = "event";
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_I2C2>;
+ resets = <&rcc I2C2_R>;
+ dmas = <&hpdma 30 0x20 0x3012>,
+ <&hpdma 31 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 42>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@40180000 {
+ compatible = "st,stm32mp25-i2c";
+ reg = <0x40180000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-names = "event";
+ interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_I2C7>;
+ resets = <&rcc I2C7_R>;
+ dmas = <&hpdma 45 0x20 0x3012>,
+ <&hpdma 46 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 47>;
+ status = "disabled";
+ };
+
+ usart6: serial@40220000 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x40220000 0x400>;
+ interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_USART6>;
+ dmas = <&hpdma 19 0x20 0x10012>,
+ <&hpdma 20 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 36>;
+ status = "disabled";
+ };
+
+ i2s1: audio-controller@40230000 {
+ compatible = "st,stm32mp25-i2s";
+ reg = <0x40230000 0x400>;
+ #sound-dai-cells = <0>;
+ interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_BUS_SPI1>, <&rcc CK_KER_SPI1>;
+ clock-names = "pclk", "i2sclk";
+ resets = <&rcc SPI1_R>;
+ dmas = <&hpdma 49 0x43 0x12>,
+ <&hpdma 50 0x43 0x21>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 22>;
+ status = "disabled";
+ };
+
+ spi1: spi@40230000 {
+ compatible = "st,stm32mp25-spi";
+ reg = <0x40230000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_SPI1>;
+ resets = <&rcc SPI1_R>;
+ dmas = <&hpdma 49 0x20 0x3012>,
+ <&hpdma 50 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 22>;
+ status = "disabled";
+ };
+
+ spi4: spi@40240000 {
+ compatible = "st,stm32mp25-spi";
+ reg = <0x40240000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_SPI4>;
+ resets = <&rcc SPI4_R>;
+ dmas = <&hpdma 55 0x20 0x3012>,
+ <&hpdma 56 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 25>;
+ status = "disabled";
+ };
+
+ spi5: spi@40280000 {
+ compatible = "st,stm32mp25-spi";
+ reg = <0x40280000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_SPI5>;
+ resets = <&rcc SPI5_R>;
+ dmas = <&hpdma 57 0x20 0x3012>,
+ <&hpdma 58 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 26>;
+ status = "disabled";
+ };
+
+ sai1: sai@40290000 {
+ compatible = "st,stm32mp25-sai";
+ reg = <0x40290000 0x4>, <0x4029a3f0 0x10>;
+ ranges = <0 0x40290000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&rcc CK_BUS_SAI1>;
+ clock-names = "pclk";
+ interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&rcc SAI1_R>;
+ access-controllers = <&rifsc 49>;
+ status = "disabled";
+
+ sai1a: audio-controller@40290004 {
+ compatible = "st,stm32-sai-sub-a";
+ reg = <0x4 0x20>;
+ #sound-dai-cells = <0>;
+ clocks = <&rcc CK_KER_SAI1>;
+ clock-names = "sai_ck";
+ dmas = <&hpdma 73 0x43 0x21>;
+ status = "disabled";
+ };
+
+ sai1b: audio-controller@40290024 {
+ compatible = "st,stm32-sai-sub-b";
+ reg = <0x24 0x20>;
+ #sound-dai-cells = <0>;
+ clocks = <&rcc CK_KER_SAI1>;
+ clock-names = "sai_ck";
+ dmas = <&hpdma 74 0x43 0x12>;
+ status = "disabled";
+ };
+ };
+
+ sai2: sai@402a0000 {
+ compatible = "st,stm32mp25-sai";
+ reg = <0x402a0000 0x4>, <0x402aa3f0 0x10>;
+ ranges = <0 0x402a0000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&rcc CK_BUS_SAI2>;
+ clock-names = "pclk";
+ interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&rcc SAI2_R>;
+ access-controllers = <&rifsc 50>;
+ status = "disabled";
+
+ sai2a: audio-controller@402a0004 {
+ compatible = "st,stm32-sai-sub-a";
+ reg = <0x4 0x20>;
+ #sound-dai-cells = <0>;
+ clocks = <&rcc CK_KER_SAI2>;
+ clock-names = "sai_ck";
+ dmas = <&hpdma 75 0x43 0x21>;
+ status = "disabled";
+ };
+
+ sai2b: audio-controller@402a0024 {
+ compatible = "st,stm32-sai-sub-b";
+ reg = <0x24 0x20>;
+ #sound-dai-cells = <0>;
+ clocks = <&rcc CK_KER_SAI2>;
+ clock-names = "sai_ck";
+ dmas = <&hpdma 76 0x43 0x12>;
+ status = "disabled";
+ };
+ };
+
+ sai3: sai@402b0000 {
+ compatible = "st,stm32mp25-sai";
+ reg = <0x402b0000 0x4>, <0x402ba3f0 0x10>;
+ ranges = <0 0x402b0000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&rcc CK_BUS_SAI3>;
+ clock-names = "pclk";
+ interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&rcc SAI3_R>;
+ access-controllers = <&rifsc 51>;
+ status = "disabled";
+
+ sai3a: audio-controller@402b0004 {
+ compatible = "st,stm32-sai-sub-a";
+ reg = <0x4 0x20>;
+ #sound-dai-cells = <0>;
+ clocks = <&rcc CK_KER_SAI3>;
+ clock-names = "sai_ck";
+ dmas = <&hpdma 77 0x43 0x21>;
+ status = "disabled";
+ };
+
+ sai3b: audio-controller@502b0024 {
+ compatible = "st,stm32-sai-sub-b";
+ reg = <0x24 0x20>;
+ #sound-dai-cells = <0>;
+ clocks = <&rcc CK_KER_SAI3>;
+ clock-names = "sai_ck";
+ dmas = <&hpdma 78 0x43 0x12>;
+ status = "disabled";
+ };
+ };
+
+ usart1: serial@40330000 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x40330000 0x400>;
+ interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_USART1>;
+ dmas = <&hpdma 9 0x20 0x10012>,
+ <&hpdma 10 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 31>;
+ status = "disabled";
+ };
+
+ sai4: sai@40340000 {
+ compatible = "st,stm32mp25-sai";
+ reg = <0x40340000 0x4>, <0x4034a3f0 0x10>;
+ ranges = <0 0x40340000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&rcc CK_BUS_SAI4>;
+ clock-names = "pclk";
+ interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&rcc SAI4_R>;
+ access-controllers = <&rifsc 52>;
+ status = "disabled";
+
+ sai4a: audio-controller@40340004 {
+ compatible = "st,stm32-sai-sub-a";
+ reg = <0x4 0x20>;
+ #sound-dai-cells = <0>;
+ clocks = <&rcc CK_KER_SAI4>;
+ clock-names = "sai_ck";
+ dmas = <&hpdma 79 0x63 0x21>;
+ status = "disabled";
+ };
+
+ sai4b: audio-controller@40340024 {
+ compatible = "st,stm32-sai-sub-b";
+ reg = <0x24 0x20>;
+ #sound-dai-cells = <0>;
+ clocks = <&rcc CK_KER_SAI4>;
+ clock-names = "sai_ck";
+ dmas = <&hpdma 80 0x43 0x12>;
+ status = "disabled";
+ };
+ };
+
+ uart7: serial@40370000 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x40370000 0x400>;
+ interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_UART7>;
+ dmas = <&hpdma 21 0x20 0x10012>,
+ <&hpdma 22 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 37>;
+ status = "disabled";
+ };
+
+ rng: rng@42020000 {
+ compatible = "st,stm32mp25-rng";
+ reg = <0x42020000 0x400>;
+ clocks = <&clk_rcbsec>, <&rcc CK_BUS_RNG>;
+ clock-names = "core", "bus";
+ resets = <&rcc RNG_R>;
+ access-controllers = <&rifsc 92>;
+ status = "disabled";
+ };
+
+ spi8: spi@46020000 {
+ compatible = "st,stm32mp25-spi";
+ reg = <0x46020000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_SPI8>;
+ resets = <&rcc SPI8_R>;
+ dmas = <&hpdma 171 0x20 0x3012>,
+ <&hpdma 172 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 29>;
+ status = "disabled";
+ };
+
+ i2c8: i2c@46040000 {
+ compatible = "st,stm32mp25-i2c";
+ reg = <0x46040000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-names = "event";
+ interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_I2C8>;
+ resets = <&rcc I2C8_R>;
+ dmas = <&hpdma 168 0x20 0x3012>,
+ <&hpdma 169 0x20 0x3021>;
+ dma-names = "rx", "tx";
+ access-controllers = <&rifsc 48>;
+ status = "disabled";
+ };
+
+ csi: csi@48020000 {
+ compatible = "st,stm32mp25-csi";
+ reg = <0x48020000 0x2000>;
+ interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&rcc CSI_R>;
+ clocks = <&rcc CK_KER_CSI>, <&rcc CK_KER_CSITXESC>,
+ <&rcc CK_KER_CSIPHY>;
+ clock-names = "pclk", "txesc", "csi2phy";
+ access-controllers = <&rifsc 86>;
+ status = "disabled";
+ };
+
+ dcmipp: dcmipp@48030000 {
+ compatible = "st,stm32mp25-dcmipp";
+ reg = <0x48030000 0x1000>;
+ interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&rcc DCMIPP_R>;
+ clocks = <&rcc CK_BUS_DCMIPP>, <&rcc CK_KER_CSI>;
+ clock-names = "kclk", "mclk";
+ access-controllers = <&rifsc 87>;
+ status = "disabled";
+ };
+
+ sdmmc1: mmc@48220000 {
+ compatible = "st,stm32mp25-sdmmc2", "arm,pl18x", "arm,primecell";
+ reg = <0x48220000 0x400>, <0x44230400 0x8>;
+ arm,primecell-periphid = <0x00353180>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_KER_SDMMC1 >;
+ clock-names = "apb_pclk";
+ resets = <&rcc SDMMC1_R>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <120000000>;
+ access-controllers = <&rifsc 76>;
+ status = "disabled";
+ };
+
+ ethernet1: ethernet@482c0000 {
+ compatible = "st,stm32mp25-dwmac", "snps,dwmac-5.20";
+ reg = <0x482c0000 0x4000>;
+ reg-names = "stmmaceth";
+ interrupts-extended = <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clock-names = "stmmaceth",
+ "mac-clk-tx",
+ "mac-clk-rx",
+ "ptp_ref",
+ "ethstp",
+ "eth-ck";
+ clocks = <&rcc CK_ETH1_MAC>,
+ <&rcc CK_ETH1_TX>,
+ <&rcc CK_ETH1_RX>,
+ <&rcc CK_KER_ETH1PTP>,
+ <&rcc CK_ETH1_STP>,
+ <&rcc CK_KER_ETH1>;
+ snps,axi-config = <&stmmac_axi_config_1>;
+ snps,mixed-burst;
+ snps,mtl-rx-config = <&mtl_rx_setup_1>;
+ snps,mtl-tx-config = <&mtl_tx_setup_1>;
+ snps,pbl = <2>;
+ snps,tso;
+ st,syscon = <&syscfg 0x3000>;
+ access-controllers = <&rifsc 60>;
+ status = "disabled";
+
+ mtl_rx_setup_1: rx-queues-config {
+ snps,rx-queues-to-use = <2>;
+ queue0 {};
+ queue1 {};
+ };
+
+ mtl_tx_setup_1: tx-queues-config {
+ snps,tx-queues-to-use = <4>;
+ queue0 {};
+ queue1 {};
+ queue2 {};
+ queue3 {};
+ };
+
+ stmmac_axi_config_1: stmmac-axi-config {
+ snps,blen = <0 0 0 0 16 8 4>;
+ snps,rd_osr_lmt = <0x7>;
+ snps,wr_osr_lmt = <0x7>;
+ };
+ };
+ };
+
+ bsec: efuse@44000000 {
+ compatible = "st,stm32mp25-bsec";
+ reg = <0x44000000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ part_number_otp@24 {
+ reg = <0x24 0x4>;
+ };
+
+ package_otp@1e8 {
+ reg = <0x1e8 0x1>;
+ bits = <0 3>;
+ };
+ };
+
+ rcc: clock-controller@44200000 {
+ compatible = "st,stm32mp25-rcc";
+ reg = <0x44200000 0x10000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ clocks = <&scmi_clk CK_SCMI_HSE>,
+ <&scmi_clk CK_SCMI_HSI>,
+ <&scmi_clk CK_SCMI_MSI>,
+ <&scmi_clk CK_SCMI_LSE>,
+ <&scmi_clk CK_SCMI_LSI>,
+ <&scmi_clk CK_SCMI_HSE_DIV2>,
+ <&scmi_clk CK_SCMI_ICN_HS_MCU>,
+ <&scmi_clk CK_SCMI_ICN_LS_MCU>,
+ <&scmi_clk CK_SCMI_ICN_SDMMC>,
+ <&scmi_clk CK_SCMI_ICN_DDR>,
+ <&scmi_clk CK_SCMI_ICN_DISPLAY>,
+ <&scmi_clk CK_SCMI_ICN_HSL>,
+ <&scmi_clk CK_SCMI_ICN_NIC>,
+ <&scmi_clk CK_SCMI_ICN_VID>,
+ <&scmi_clk CK_SCMI_FLEXGEN_07>,
+ <&scmi_clk CK_SCMI_FLEXGEN_08>,
+ <&scmi_clk CK_SCMI_FLEXGEN_09>,
+ <&scmi_clk CK_SCMI_FLEXGEN_10>,
+ <&scmi_clk CK_SCMI_FLEXGEN_11>,
+ <&scmi_clk CK_SCMI_FLEXGEN_12>,
+ <&scmi_clk CK_SCMI_FLEXGEN_13>,
+ <&scmi_clk CK_SCMI_FLEXGEN_14>,
+ <&scmi_clk CK_SCMI_FLEXGEN_15>,
+ <&scmi_clk CK_SCMI_FLEXGEN_16>,
+ <&scmi_clk CK_SCMI_FLEXGEN_17>,
+ <&scmi_clk CK_SCMI_FLEXGEN_18>,
+ <&scmi_clk CK_SCMI_FLEXGEN_19>,
+ <&scmi_clk CK_SCMI_FLEXGEN_20>,
+ <&scmi_clk CK_SCMI_FLEXGEN_21>,
+ <&scmi_clk CK_SCMI_FLEXGEN_22>,
+ <&scmi_clk CK_SCMI_FLEXGEN_23>,
+ <&scmi_clk CK_SCMI_FLEXGEN_24>,
+ <&scmi_clk CK_SCMI_FLEXGEN_25>,
+ <&scmi_clk CK_SCMI_FLEXGEN_26>,
+ <&scmi_clk CK_SCMI_FLEXGEN_27>,
+ <&scmi_clk CK_SCMI_FLEXGEN_28>,
+ <&scmi_clk CK_SCMI_FLEXGEN_29>,
+ <&scmi_clk CK_SCMI_FLEXGEN_30>,
+ <&scmi_clk CK_SCMI_FLEXGEN_31>,
+ <&scmi_clk CK_SCMI_FLEXGEN_32>,
+ <&scmi_clk CK_SCMI_FLEXGEN_33>,
+ <&scmi_clk CK_SCMI_FLEXGEN_34>,
+ <&scmi_clk CK_SCMI_FLEXGEN_35>,
+ <&scmi_clk CK_SCMI_FLEXGEN_36>,
+ <&scmi_clk CK_SCMI_FLEXGEN_37>,
+ <&scmi_clk CK_SCMI_FLEXGEN_38>,
+ <&scmi_clk CK_SCMI_FLEXGEN_39>,
+ <&scmi_clk CK_SCMI_FLEXGEN_40>,
+ <&scmi_clk CK_SCMI_FLEXGEN_41>,
+ <&scmi_clk CK_SCMI_FLEXGEN_42>,
+ <&scmi_clk CK_SCMI_FLEXGEN_43>,
+ <&scmi_clk CK_SCMI_FLEXGEN_44>,
+ <&scmi_clk CK_SCMI_FLEXGEN_45>,
+ <&scmi_clk CK_SCMI_FLEXGEN_46>,
+ <&scmi_clk CK_SCMI_FLEXGEN_47>,
+ <&scmi_clk CK_SCMI_FLEXGEN_48>,
+ <&scmi_clk CK_SCMI_FLEXGEN_49>,
+ <&scmi_clk CK_SCMI_FLEXGEN_50>,
+ <&scmi_clk CK_SCMI_FLEXGEN_51>,
+ <&scmi_clk CK_SCMI_FLEXGEN_52>,
+ <&scmi_clk CK_SCMI_FLEXGEN_53>,
+ <&scmi_clk CK_SCMI_FLEXGEN_54>,
+ <&scmi_clk CK_SCMI_FLEXGEN_55>,
+ <&scmi_clk CK_SCMI_FLEXGEN_56>,
+ <&scmi_clk CK_SCMI_FLEXGEN_57>,
+ <&scmi_clk CK_SCMI_FLEXGEN_58>,
+ <&scmi_clk CK_SCMI_FLEXGEN_59>,
+ <&scmi_clk CK_SCMI_FLEXGEN_60>,
+ <&scmi_clk CK_SCMI_FLEXGEN_61>,
+ <&scmi_clk CK_SCMI_FLEXGEN_62>,
+ <&scmi_clk CK_SCMI_FLEXGEN_63>,
+ <&scmi_clk CK_SCMI_ICN_APB1>,
+ <&scmi_clk CK_SCMI_ICN_APB2>,
+ <&scmi_clk CK_SCMI_ICN_APB3>,
+ <&scmi_clk CK_SCMI_ICN_APB4>,
+ <&scmi_clk CK_SCMI_ICN_APBDBG>,
+ <&scmi_clk CK_SCMI_TIMG1>,
+ <&scmi_clk CK_SCMI_TIMG2>,
+ <&scmi_clk CK_SCMI_PLL3>,
+ <&clk_dsi_txbyte>;
+ access-controllers = <&rifsc 156>;
+ };
+
+ exti1: interrupt-controller@44220000 {
+ compatible = "st,stm32mp1-exti", "syscon";
+ reg = <0x44220000 0x400>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts-extended =
+ <&intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>, /* EXTI_0 */
+ <&intc GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 276 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>, /* EXTI_10 */
+ <&intc GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>,
+ <0>, /* EXTI_20 */
+ <&intc GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>, /* EXTI_30 */
+ <&intc GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <&intc GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, /* EXTI_40 */
+ <&intc GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>, /* EXTI_50 */
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <&intc GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>,
+ <0>, /* EXTI_60 */
+ <&intc GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <0>,
+ <&intc GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <0>,
+ <&intc GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <&intc GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, /* EXTI_70 */
+ <0>,
+ <&intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>,
+ <0>, /* EXTI_80 */
+ <0>,
+ <0>,
+ <&intc GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ syscfg: syscon@44230000 {
+ compatible = "st,stm32mp23-syscfg", "syscon";
+ reg = <0x44230000 0x10000>;
+ };
+
+ pinctrl: pinctrl@44240000 {
+ compatible = "st,stm32mp257-pinctrl";
+ ranges = <0 0x44240000 0xa0400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&exti1>;
+ st,syscfg = <&exti1 0x60 0xff>;
+ pins-are-numbered;
+
+ gpioa: gpio@44240000 {
+ reg = <0x0 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOA>;
+ st,bank-name = "GPIOA";
+ status = "disabled";
+ };
+
+ gpiob: gpio@44250000 {
+ reg = <0x10000 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOB>;
+ st,bank-name = "GPIOB";
+ status = "disabled";
+ };
+
+ gpioc: gpio@44260000 {
+ reg = <0x20000 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOC>;
+ st,bank-name = "GPIOC";
+ status = "disabled";
+ };
+
+ gpiod: gpio@44270000 {
+ reg = <0x30000 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOD>;
+ st,bank-name = "GPIOD";
+ status = "disabled";
+ };
+
+ gpioe: gpio@44280000 {
+ reg = <0x40000 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOE>;
+ st,bank-name = "GPIOE";
+ status = "disabled";
+ };
+
+ gpiof: gpio@44290000 {
+ reg = <0x50000 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOF>;
+ st,bank-name = "GPIOF";
+ status = "disabled";
+ };
+
+ gpiog: gpio@442a0000 {
+ reg = <0x60000 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOG>;
+ st,bank-name = "GPIOG";
+ status = "disabled";
+ };
+
+ gpioh: gpio@442b0000 {
+ reg = <0x70000 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOH>;
+ st,bank-name = "GPIOH";
+ status = "disabled";
+ };
+
+ gpioi: gpio@442c0000 {
+ reg = <0x80000 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOI>;
+ st,bank-name = "GPIOI";
+ status = "disabled";
+ };
+
+ gpioj: gpio@442d0000 {
+ reg = <0x90000 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOJ>;
+ st,bank-name = "GPIOJ";
+ status = "disabled";
+ };
+
+ gpiok: gpio@442e0000 {
+ reg = <0xa0000 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOK>;
+ st,bank-name = "GPIOK";
+ status = "disabled";
+ };
+ };
+
+ rtc: rtc@46000000 {
+ compatible = "st,stm32mp25-rtc";
+ reg = <0x46000000 0x400>;
+ clocks = <&scmi_clk CK_SCMI_RTC>,
+ <&scmi_clk CK_SCMI_RTCCK>;
+ clock-names = "pclk", "rtc_ck";
+ interrupts-extended = <&exti2 17 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ pinctrl_z: pinctrl@46200000 {
+ compatible = "st,stm32mp257-z-pinctrl";
+ ranges = <0 0x46200000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&exti1>;
+ st,syscfg = <&exti1 0x60 0xff>;
+ pins-are-numbered;
+
+ gpioz: gpio@46200000 {
+ reg = <0 0x400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+ st,bank-name = "GPIOZ";
+ st,bank-ioport = <11>;
+ status = "disabled";
+ };
+
+ };
+
+ exti2: interrupt-controller@46230000 {
+ compatible = "st,stm32mp1-exti", "syscon";
+ reg = <0x46230000 0x400>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts-extended =
+ <&intc GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, /* EXTI_0 */
+ <&intc GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>, /* EXTI_10 */
+ <&intc GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <0>,
+ <0>, /* EXTI_20 */
+ <&intc GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <0>,
+ <&intc GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <&intc GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>, /* EXTI_30 */
+ <&intc GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <&intc GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <0>,
+ <&intc GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <0>,
+ <&intc GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>, /* EXTI_40 */
+ <0>,
+ <0>,
+ <&intc GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <0>,
+ <&intc GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <&intc GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, /* EXTI_50 */
+ <&intc GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>, /* EXTI_60 */
+ <&intc GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <&intc GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
+ <0>,
+ <0>,
+ <&intc GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>; /* EXTI_70 */
+ };
+
+ intc: interrupt-controller@4ac10000 {
+ compatible = "arm,cortex-a7-gic";
+ reg = <0x4ac10000 0x1000>,
+ <0x4ac20000 0x2000>,
+ <0x4ac40000 0x2000>,
+ <0x4ac60000 0x2000>;
+ #interrupt-cells = <3>;
+ #address-cells = <1>;
+ interrupt-controller;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp233.dtsi b/arch/arm64/boot/dts/st/stm32mp233.dtsi
new file mode 100644
index 000000000000..78f4059fca5d
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp233.dtsi
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp231.dtsi"
+
+/ {
+ cpus {
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a35";
+ reg = <1>;
+ device_type = "cpu";
+ enable-method = "psci";
+ power-domains = <&cpu1_pd>;
+ power-domain-names = "psci";
+ };
+ };
+
+ arm-pmu {
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>;
+ };
+
+ psci {
+ cpu1_pd: power-domain-cpu1 {
+ #power-domain-cells = <0>;
+ power-domains = <&cluster_pd>;
+ };
+ };
+
+ timer {
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
+
+&optee {
+ interrupts = <GIC_PPI 15 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+};
+
+&rifsc {
+ ethernet2: ethernet@482d0000 {
+ compatible = "st,stm32mp25-dwmac", "snps,dwmac-5.20";
+ reg = <0x482d0000 0x4000>;
+ reg-names = "stmmaceth";
+ interrupts-extended = <&intc GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clock-names = "stmmaceth",
+ "mac-clk-tx",
+ "mac-clk-rx",
+ "ptp_ref",
+ "ethstp",
+ "eth-ck";
+ clocks = <&rcc CK_ETH2_MAC>,
+ <&rcc CK_ETH2_TX>,
+ <&rcc CK_ETH2_RX>,
+ <&rcc CK_KER_ETH2PTP>,
+ <&rcc CK_ETH2_STP>,
+ <&rcc CK_KER_ETH2>;
+ snps,axi-config = <&stmmac_axi_config_2>;
+ snps,mixed-burst;
+ snps,mtl-rx-config = <&mtl_rx_setup_2>;
+ snps,mtl-tx-config = <&mtl_tx_setup_2>;
+ snps,pbl = <2>;
+ snps,tso;
+ st,syscon = <&syscfg 0x3400>;
+ access-controllers = <&rifsc 61>;
+ status = "disabled";
+
+ mtl_rx_setup_2: rx-queues-config {
+ snps,rx-queues-to-use = <2>;
+ queue0 {};
+ queue1 {};
+ };
+
+ mtl_tx_setup_2: tx-queues-config {
+ snps,tx-queues-to-use = <4>;
+ queue0 {};
+ queue1 {};
+ queue2 {};
+ queue3 {};
+ };
+
+ stmmac_axi_config_2: stmmac-axi-config {
+ snps,blen = <0 0 0 0 16 8 4>;
+ snps,rd_osr_lmt = <0x7>;
+ snps,wr_osr_lmt = <0x7>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp235.dtsi b/arch/arm64/boot/dts/st/stm32mp235.dtsi
new file mode 100644
index 000000000000..2719c088dd59
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp235.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp233.dtsi"
+
+&rifsc {
+ vdec: vdec@480d0000 {
+ compatible = "st,stm32mp25-vdec";
+ reg = <0x480d0000 0x3c8>;
+ interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc CK_BUS_VDEC>;
+ access-controllers = <&rifsc 89>;
+ };
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp235f-dk.dts b/arch/arm64/boot/dts/st/stm32mp235f-dk.dts
new file mode 100644
index 000000000000..04d1b434c433
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp235f-dk.dts
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Amelie Delaunay <amelie.delaunay@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "stm32mp235.dtsi"
+#include "stm32mp23xf.dtsi"
+#include "stm32mp25-pinctrl.dtsi"
+#include "stm32mp25xxak-pinctrl.dtsi"
+
+/ {
+ model = "STMicroelectronics STM32MP235F-DK Discovery Board";
+ compatible = "st,stm32mp235f-dk", "st,stm32mp235";
+
+ aliases {
+ serial0 = &usart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-user-1 {
+ label = "User-1";
+ linux,code = <BTN_1>;
+ gpios = <&gpioc 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ button-user-2 {
+ label = "User-2";
+ linux,code = <BTN_2>;
+ gpios = <&gpioc 11 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led-blue {
+ function = LED_FUNCTION_HEARTBEAT;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpioh 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0x1 0x0>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ fw@80000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x80000000 0x0 0x4000000>;
+ no-map;
+ };
+ };
+};
+
+&arm_wdt {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&scmi_regu {
+ scmi_vddio1: regulator@0 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ scmi_vdd_sdcard: regulator@23 {
+ reg = <VOLTD_SCMI_STPMIC2_LDO7>;
+ regulator-name = "vdd_sdcard";
+ };
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ cd-gpios = <&gpiod 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&scmi_vdd_sdcard>;
+ vqmmc-supply = <&scmi_vddio1>;
+ status = "okay";
+};
+
+&usart2 {
+ pinctrl-names = "default", "idle", "sleep";
+ pinctrl-0 = <&usart2_pins_a>;
+ pinctrl-1 = <&usart2_idle_pins_a>;
+ pinctrl-2 = <&usart2_sleep_pins_a>;
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp23xc.dtsi b/arch/arm64/boot/dts/st/stm32mp23xc.dtsi
new file mode 100644
index 000000000000..e33b00b424e1
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp23xc.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp23xf.dtsi b/arch/arm64/boot/dts/st/stm32mp23xf.dtsi
new file mode 100644
index 000000000000..e33b00b424e1
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp23xf.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+};
diff --git a/arch/arm64/boot/dts/st/stm32mp257f-dk.dts b/arch/arm64/boot/dts/st/stm32mp257f-dk.dts
new file mode 100644
index 000000000000..a278a1e3ce03
--- /dev/null
+++ b/arch/arm64/boot/dts/st/stm32mp257f-dk.dts
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "stm32mp257.dtsi"
+#include "stm32mp25xf.dtsi"
+#include "stm32mp25-pinctrl.dtsi"
+#include "stm32mp25xxak-pinctrl.dtsi"
+
+/ {
+ model = "STMicroelectronics STM32MP257F-DK Discovery Board";
+ compatible = "st,stm32mp257f-dk", "st,stm32mp257";
+
+ aliases {
+ serial0 = &usart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-user-1 {
+ label = "User-1";
+ linux,code = <BTN_1>;
+ gpios = <&gpioc 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ button-user-2 {
+ label = "User-2";
+ linux,code = <BTN_2>;
+ gpios = <&gpioc 11 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led-blue {
+ function = LED_FUNCTION_HEARTBEAT;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpioh 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0x1 0x0>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ fw@80000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x80000000 0x0 0x4000000>;
+ no-map;
+ };
+ };
+};
+
+&arm_wdt {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&scmi_regu {
+ scmi_vddio1: regulator@0 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ scmi_vdd_sdcard: regulator@23 {
+ reg = <VOLTD_SCMI_STPMIC2_LDO7>;
+ regulator-name = "vdd_sdcard";
+ };
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ cd-gpios = <&gpiod 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&scmi_vdd_sdcard>;
+ vqmmc-supply = <&scmi_vddio1>;
+ status = "okay";
+};
+
+&usart2 {
+ pinctrl-names = "default", "idle", "sleep";
+ pinctrl-0 = <&usart2_pins_a>;
+ pinctrl-1 = <&usart2_idle_pins_a>;
+ pinctrl-2 = <&usart2_sleep_pins_a>;
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "okay";
+};
generated by cgit (git 2.34.1) at 2025-05-13 16:12:24 +0000