diff options
| -rw-r--r-- | drivers/spi/spi-tegra210-quad.c | 14 | ||||
| -rw-r--r-- | include/linux/spi/spi.h | 16 |
2 files changed, 27 insertions, 3 deletions
diff --git a/drivers/spi/spi-tegra210-quad.c b/drivers/spi/spi-tegra210-quad.c index bea376acea1f..fbd14dd7be44 100644 --- a/drivers/spi/spi-tegra210-quad.c +++ b/drivers/spi/spi-tegra210-quad.c @@ -142,6 +142,7 @@ #define QSPI_GLOBAL_CONFIG 0X1a4 #define QSPI_CMB_SEQ_EN BIT(0) +#define QSPI_TPM_WAIT_POLL_EN BIT(1) #define QSPI_CMB_SEQ_ADDR 0x1a8 #define QSPI_ADDRESS_VALUE_SET(X) (((x) & 0xFFFF) << 0) @@ -164,6 +165,7 @@ struct tegra_qspi_soc_data { bool has_dma; bool cmb_xfer_capable; + bool supports_tpm; unsigned int cs_count; }; @@ -1065,6 +1067,12 @@ static int tegra_qspi_combined_seq_xfer(struct tegra_qspi *tqspi, /* Enable Combined sequence mode */ val = tegra_qspi_readl(tqspi, QSPI_GLOBAL_CONFIG); + if (spi->mode & SPI_TPM_HW_FLOW) { + if (tqspi->soc_data->supports_tpm) + val |= QSPI_TPM_WAIT_POLL_EN; + else + return -EIO; + } val |= QSPI_CMB_SEQ_EN; tegra_qspi_writel(tqspi, val, QSPI_GLOBAL_CONFIG); /* Process individual transfer list */ @@ -1196,6 +1204,8 @@ static int tegra_qspi_non_combined_seq_xfer(struct tegra_qspi *tqspi, /* Disable Combined sequence mode */ val = tegra_qspi_readl(tqspi, QSPI_GLOBAL_CONFIG); val &= ~QSPI_CMB_SEQ_EN; + if (tqspi->soc_data->supports_tpm) + val &= ~QSPI_TPM_WAIT_POLL_EN; tegra_qspi_writel(tqspi, val, QSPI_GLOBAL_CONFIG); list_for_each_entry(transfer, &msg->transfers, transfer_list) { struct spi_transfer *xfer = transfer; @@ -1454,24 +1464,28 @@ static irqreturn_t tegra_qspi_isr_thread(int irq, void *context_data) static struct tegra_qspi_soc_data tegra210_qspi_soc_data = { .has_dma = true, .cmb_xfer_capable = false, + .supports_tpm = false, .cs_count = 1, }; static struct tegra_qspi_soc_data tegra186_qspi_soc_data = { .has_dma = true, .cmb_xfer_capable = true, + .supports_tpm = false, .cs_count = 1, }; static struct tegra_qspi_soc_data tegra234_qspi_soc_data = { .has_dma = false, .cmb_xfer_capable = true, + .supports_tpm = true, .cs_count = 1, }; static struct tegra_qspi_soc_data tegra241_qspi_soc_data = { .has_dma = false, .cmb_xfer_capable = true, + .supports_tpm = true, .cs_count = 4, }; diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index 873ced6ae4ca..cfe42f8cd7a4 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -184,8 +184,18 @@ struct spi_device { u8 chip_select; u8 bits_per_word; bool rt; -#define SPI_NO_TX BIT(31) /* No transmit wire */ -#define SPI_NO_RX BIT(30) /* No receive wire */ +#define SPI_NO_TX BIT(31) /* No transmit wire */ +#define SPI_NO_RX BIT(30) /* No receive wire */ + /* + * TPM specification defines flow control over SPI. Client device + * can insert a wait state on MISO when address is transmitted by + * controller on MOSI. Detecting the wait state in software is only + * possible for full duplex controllers. For controllers that support + * only half-duplex, the wait state detection needs to be implemented + * in hardware. TPM devices would set this flag when hardware flow + * control is expected from SPI controller. + */ +#define SPI_TPM_HW_FLOW BIT(29) /* TPM HW flow control */ /* * All bits defined above should be covered by SPI_MODE_KERNEL_MASK. * The SPI_MODE_KERNEL_MASK has the SPI_MODE_USER_MASK counterpart, @@ -195,7 +205,7 @@ struct spi_device { * These bits must not overlap. A static assert check should make sure of that. * If adding extra bits, make sure to decrease the bit index below as well. */ -#define SPI_MODE_KERNEL_MASK (~(BIT(30) - 1)) +#define SPI_MODE_KERNEL_MASK (~(BIT(29) - 1)) u32 mode; int irq; void *controller_state; |