| Age | Commit message (Collapse) | Author |
|---|
|
Radxa E20C route UART0 M0 pins (GPIO4_C7 and GPIO4_D0) to the onboard
CH340B for debug console use.
Add pinctrl for UART0 M0 pins used for serial console.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250228064024.3200000-6-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add pinctrl and gpio nodes for RK3528 and import rk3528-pinctrl.dtsi
from vendor linux-6.1-stan-rkr5 kernel with the hdmi-pins-idle node
removed due to missing label reference to pcfg_output_low_pull_down.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250228064024.3200000-5-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The GPIO is accessible via ioc grf syscon registers on RK3528.
Add compatible string for RK3528 ioc grf syscon.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250228064024.3200000-2-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Adds device tree entries for the touchbar screen
Co-developed-by: Janne Grunau <j@jannau.net>
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sasha Finkelstein <fnkl.kernel@gmail.com>
Link: https://lore.kernel.org/r/20250217-adpdrm-v7-4-ca2e44b3c7d8@gmail.com
Signed-off-by: Sven Peter <sven@svenpeter.dev>
|
|
Add cpu{1-3} device nodes to the corstone1000 device tree to enable the
support for secondary CPU cores.
This update facilitates symmetric multiprocessing (SMP) support on the
corstone1000 Fixed Virtual Platform (FVP), allowing the secondary cores
to be properly initialised and utilised.
Only FVP platform will have SMP support and hence the secondary cpu
definitions are not added to corstone1000.dtsi.
Signed-off-by: Hugues KAMBA MPIANA <hugues.kambampiana@arm.com>
Message-Id: <20250303170012.469576-1-hugues.kambampiana@arm.com>
(sudeep.holla: Added psci enable-method for cpu0)
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Commit under Fixes added the 'idle-states' property for SERDES4 lane muxes
without defining the corresponding register offsets and masks for it in the
'mux-reg-masks' property within the 'serdes_ln_ctrl' node.
Fix this.
Fixes: 7287d423f138 ("arm64: dts: ti: k3-j784s4-main: Add system controller and SERDES lane mux")
Cc: stable@vger.kernel.org
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250228053850.506028-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
On AM62P-based SoCs the AUDIO_REFCLKx clocks can be used as an input to
external peripherals when configured through CTRL_MMR, so add the
clock nodes.
Link: http://downloads.ti.com/tisci/esd/latest/5_soc_doc/am62px/clocks.html
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20250206153911.414702-1-francesco@dolcini.it
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Reserve a portion of memory for inter-processor communication between
all remote processors running RTOS or baremetal firmware.
Move ramoops to lower region so the IPC fits to the correct address.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20250131093531.1054924-2-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Reserve a portion of memory for inter-processor communication between
all remote processors running RTOS or baremetal firmware.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20250131093531.1054924-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add alias for mcu_uart0.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/r/20250203-topic-am62-serial-aliases-v6-14-v1-3-f26d4124a9f1@baylibre.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add alias for mcu_uart0.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/r/20250203-topic-am62-serial-aliases-v6-14-v1-2-f26d4124a9f1@baylibre.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add aliases for mcu_uart0 and wkup_uart0.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/r/20250203-topic-am62-serial-aliases-v6-14-v1-1-f26d4124a9f1@baylibre.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
After the SoC has entered the Deep Sleep mode, USB1 can be used to wakeup
the SoC based on USB events triggered by USB devices. This requires that
the pin corresponding to the Type-A connector remains pulled up even after
the SoC has entered the Deep Sleep mode. Hence, enable Deep Sleep pullup /
pulldown selection for the USB1_DRVBUS pin and set its Deep Sleep state to
PULL_UP.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250130062550.1554651-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
In the same lines of commit 9e8560556f9c ("arm64: dts: ti:
k3-am62x-sk-common: Reserve 128MiB of global CMA"), reserve global CMA
pool for:
LCD Display: 16MiB, HDMI (1080p): 16MiB, GPU: 16MiB, CSI2 1 1080p
sensor: 32MiB with a 32MiB set for other peripherals and a 16MiB
buffer.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20250131173508.1338842-1-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The USB0 instance of USB on J721E SoC can be used for USB DFU boot.
Since the USB Type-C interface on the J721E-SK is connected to USB0 via
SERDES3, supporting USB DFU boot requires SERDES3 link associated with
USB0 to be functional at all stages of the USB DFU boot process. Thus,
add the "bootph-all" boot phase tag to "serdes3_usb_link" device-tree node.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250209081738.1874749-3-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The USB0 instance of USB on J721E SoC can be used for USB DFU boot.
Since the USB Type-C interface on the J721E-EVM is connected to USB0 via
SERDES3, supporting USB DFU boot requires SERDES3 link associated with
USB0 to be functional at all stages of the USB DFU boot process. Thus,
add the "bootph-all" boot phase tag to "serdes3_usb_link" device-tree node.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250209081738.1874749-2-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Similar to the TI K3-AM62x Soc commit ce27f7f9e328c8582a169f97f1466976561f1
("arm64: dts: ti: k3-am62-wakeup: Configure ti-sysc for wkup_uart0")
The devices in the wkup domain are capable of waking up the system from
suspend. We can configure the wkup domain devices in a generic way using
the ti-sysc interconnect target module driver like we have done with the
earlier TI SoCs.
As ti-sysc manages the SYSCONFIG related registers independent of the
child hardware device, the wake-up configuration is also set even if
wkup_uart0 is reserved by sysfw.
The wkup_uart0 device has interconnect target module register mapping like
dra7 wkup uart. There is a 1 MB interconnect target range with one uart IP
block in the target module. The power domain and clock affects the whole
interconnect target module.
Note we change the functional clock name to follow the ti-sysc binding
and use "fck" instead of "fclk".
Also note that we need to disable the target module reset as noted by
Markus. Otherwise the sysfw using wkup_uart0 can get confused on some
devices leading to boot time issues such as mbox timeouts.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20250212215248.746838-1-k-willis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Adds alias for SoC RTC so that it gets assigned rtc0. PMIC node is
assigned rtc1 so that PMIC RTC gets probed as rtc1. This makes it
consistent for testing rtcwake with other AM62 devices where rtc0
is SoC RTC.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
[k-willis@ti.com: Reworded commit message]
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://lore.kernel.org/r/20250214232212.1158505-1-k-willis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
When used as boot device, OSPI flash hosts different boot
binaries and rootfs etc.
So Add partition details for images hosted on OSPI flash.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250215070059.1593489-1-u-kumar1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The simple-audio-card's microphone widget currently connects to the
headphone jack. Routing the microphone input to the microphone jack
allows for independent operation of the microphone and headphones.
This resolves the following boot-time kernel log message, which
indicated a conflict when the microphone and headphone functions were
not separated:
debugfs: File 'Headphone Jack' in directory 'dapm' already present!
Fixes: f5bf894c865b ("arm64: dts: ti: verdin-am62: dahlia: add sound card")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Jai Luthra <jai.luthra@linux.dev>
Link: https://lore.kernel.org/r/20250217144643.178222-1-eichest@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Currently we get the warning:
"GICv3: [Firmware Bug]: GICR region 0x0000000001900000 has
overlapping address"
As per TRM GICD is 64 KB. Fix it by correcting the size of GICD.
Cc: stable@vger.kernel.org
Fixes: 9cc161a4509c ("arm64: dts: ti: Refactor J784s4 SoC files to a common file")
Link: https://lore.kernel.org/r/20250218052248.4734-1-j-keerthy@ti.com
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The USB0 instance of USB on AM62Px SoC can be used for USB DFU boot. This
requires USB0 to be enabled at all stages of the boot process. In order to
support USB DFU boot on AM62P5-SK, add the "bootph-all" property to USB0.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250122124223.1118789-3-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The USB0 instance of USB on AM62Ax SoC can be used for USB DFU boot. This
requires USB0 to be enabled at all stages of the boot process. In order to
support USB DFU boot on AM62A7-SK, add the "bootph-all" property to USB0.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250122124223.1118789-2-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Jaguar has two type-c ports connected to fusb302 controllers that can
work both in host and device mode and can also run in display-port
altmode.
While these ports can work in dual-role data mode, they do not support
powering the device itself as power-sink. This causes issues because
the current infrastructure does not cope well with dual-role data
without dual-role power.
So add the necessary nodes for the type-c controllers as well as enable
the relevant core usb nodes. So far host modes works reliably, but
device-mode does not. So devicemode needs more investigation.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Tested-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250228150853.329175-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enabling the GPU power domain requires that the GPU regulator is
enabled. The regulator is enabled at boot time, but gets disabled
automatically when there are no users.
This means the system might run into a failure state hanging the
whole system for the following use cases:
* if the GPU driver is being probed late (e.g. build as a
module and firmware is not in initramfs), the regulator
might already have been disabled. In that case the power
domain is enabled before the regulator.
* unbinding the GPU driver will disable the PM domain and
the regulator. When the driver is bound again, the PM
domain will be enabled before the regulator and error
appears.
Avoid this by adding an explicit regulator dependency to the
power domain.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reported-by: Adrián Martínez Larumbe <adrian.larumbe@collabora.com>
Tested-by: Adrian Larumbe <adrian.larumbe@collabora.com> # On Rock 5B
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250220-rk3588-gpu-pwr-domain-regulator-v6-8-a4f9c24e5b81@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
HDMI audio is available on the Orange Pi 5 Ultra HDMI1 TX port.
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
Link: https://lore.kernel.org/r/20250222193332.1761-6-honyuenkwun@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable the only HDMI output port on the Orange Pi 5 Ultra
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
Tested-By: Johannes Erdfelt <johannes@erdfelt.com>
Link: https://lore.kernel.org/r/20250222193332.1761-5-honyuenkwun@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RK3588 Single Board Computer includes
- eMMC
- microSD
- UART
- 2 PWM LEDs
- RTC
- RTL8125 network controller on PCIe 2.0x1.
- M.2 M-key connector routed to PCIe 3.0x4
- PWM controlled heat sink fan.
- 2 USB2 ports
- lower USB3 port
- upper USB3 port with OTG capability
- Mali GPU
- SPI NOR flash
- Mask Rom button
- Analog audio using es8388 codec via the headset jack and onboard mic
- HDMI1
- HDMI IN
the vcc5v0_usb30 regulator shares the same enable gpio pin as the
vcc5v0_usb20 regulator.
The Orange Pi 5 Ultra is a single board computer powered by the Rockchip
RK3588 with similar board layout as the 5 Max but with the HDMI0 swapped
for HDMI IN.
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
Tested-By: Johannes Erdfelt <johannes@erdfelt.com>
Link: https://lore.kernel.org/r/20250222193332.1761-4-honyuenkwun@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add devicetree binding for the Xunlong Orange Pi 5 Ultra board.
The Orange Pi 5 Ultra is a single board computer powered by the Rockchip
RK3588 with similar board layout as the 5 Max but with the HDMI0 swapped
for HDMI IN.
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250222193332.1761-3-honyuenkwun@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Orange Pi 5 Plus and Orange Pi 5 Max have 2SK3018s attached to the
PWM LEDs. The Orange Pi 5 Ultra does not, and thus needs the PWM
polarity inverted.
Also remove the model/compatible from the dtsi. It should be at the
board level only.
Fixes: c600d252dc52 ("arm64: dts: rockchip: Add Orange Pi 5 Max board")
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
Link: https://lore.kernel.org/r/20250222193332.1761-2-honyuenkwun@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable the HDMI port next to ethernet port.
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Link: https://lore.kernel.org/r/20250225030904.2813023-1-liujianfeng1994@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
HDMI audio is available on the Rock 5B HDMI TX ports.
Enable it for both ports.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Fixes: 419d1918105e ("ASoC: simple-card-utils: use __free(device_node) for device node")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20250217215641.372723-4-detlev.casanova@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
For hdmi0_sound, use the simple-audio-card driver with the hdmi0 QP node
as CODEC and the i2s5 device as CPU.
Similarly for hdmi1_sound, the CODEC is the hdmi1 node and the CPU is
i2s6, but only added in the rk3588-extra.dtsi device tree as the second
TX HDMI port is not available on base versions of the SoC.
The simple-audio-card,mclk-fs value is set to 128 as it is done in
the downstream driver.
The #sound-dai-cells value is set to 0 in the hdmi0 and hdmi1 nodes so
that they can be used as audio codec nodes.
Tested-by: Quentin Schulz <quentin.schulz@cherry.de> # RK3588 Tiger Haikou
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Fixes: 419d1918105e ("ASoC: simple-card-utils: use __free(device_node) for device node")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20250217215641.372723-3-detlev.casanova@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the necessary DT changes to enable the second HDMI output port on
Rockchip RK3588 EVB1.
While at it, switch the position of &vop_mmu and @vop to maintain the
alphabetical order.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250223-vop2-hdmi1-disp-modes-v2-5-f4cec5e06fbe@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
VOP2 on RK3588 is able to use the HDMI PHY PLL as an alternative and
more accurate pixel clock source to improve handling of display modes up
to 4K@60Hz on video ports 0, 1 and 2.
The HDMI1 PHY PLL clock source cannot be added directly to vop node in
rk3588-base.dtsi, along with the HDMI0 related one, because HDMI1 is an
optional feature and its PHY node belongs to a separate (extra) DT file.
Therefore, add the HDMI1 PHY PLL clock source to VOP2 by overwriting its
clocks & clock-names properties in the extra DT file.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250223-vop2-hdmi1-disp-modes-v2-4-f4cec5e06fbe@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Since commit c4b09c562086 ("phy: phy-rockchip-samsung-hdptx: Add clock
provider support"), the HDMI PHY PLL can be used as an alternative and
more accurate pixel clock source for VOP2 to improve display modes
handling on RK3588 SoC.
Add the missing #clock-cells property to allow using the clock provider
functionality of HDMI1 PHY.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250223-vop2-hdmi1-disp-modes-v2-3-f4cec5e06fbe@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add Vincenzo Frascino <vincenzo.frascino@arm.com> as Arm Morello Software
Development Platform Maintainer.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Message-Id: <20250221180349.1413089-11-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The Morello architecture is an experimental extension to Armv8.2-A,
which extends the AArch64 state with the principles proposed in
version 7 of the Capability Hardware Enhanced RISC Instructions
(CHERI) ISA.
Introduce Morello fvp dts.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Message-Id: <20250221180349.1413089-10-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The Morello architecture is an experimental extension to Armv8.2-A,
which extends the AArch64 state with the principles proposed in
version 7 of the Capability Hardware Enhanced RISC Instructions
(CHERI) ISA.
Introduce Morello SoC dts.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Message-Id: <20250221180349.1413089-9-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The Morello architecture is an experimental extension to Armv8.2-A,
which extends the AArch64 state with the principles proposed in
version 7 of the Capability Hardware Enhanced RISC Instructions
(CHERI) ISA.
The Morello Platform (soc) and the Fixed Virtual Platfom (fvp) share
some functionalities that have conveniently been included in
morello.dtsi to avoid duplication.
Introduce morello.dtsi.
Note: Morello fvp will be introduced with a future patch series.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Message-Id: <20250221180349.1413089-8-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Add support for the ARM Rainier CPU core PMU.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Message-Id: <20250221180349.1413089-6-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The Arm Morello System Development Platform uses Rainier CPUs.
Add compatibility to Rainier.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Message-Id: <20250221180349.1413089-5-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Add compatibility to Arm Morello Fixed Virtual Platform.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Message-Id: <20250221180349.1413089-4-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Add compatibility to Arm Morello System Development Platform.
Note: Morello is at the same time the name of an Architecture [1], an SoC
[2] and a Board [2].
To distinguish in between Architecture/SoC and Board we refer to the first
as arm,morello and to the second as arm,morello-sdp.
[1] https://developer.arm.com/Architectures/Morello
[2] https://www.morello-project.org/
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Message-Id: <20250221180349.1413089-3-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Update the description and contextually the help text of
CONFIG_ARCH_VEXPRESS to reflect the inclusion of all ARM Ltd Platforms.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Message-Id: <20250221180349.1413089-2-vincenzo.frascino@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
As indicated by the board silkscreen, there are three user LEDs.
Add the missing one.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114513.1098844-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Associate the LED node name with the corresponding board silkscreen for
more precise identification. In fact, the board has a total of seven
LEDs, some of which are user-controllable (i. e. usr{1,2,3}), while
others are directly controlled by hardware (e. g. power, overcurrent,
...). All these LEDs are either green or red, so using the names
led-green and led-red for the two LEDs mapped in the DTS does not
simplify their identification on the board.
Moreover, this patch is a prerequisite for adding the usr3 LED, which
has not been included in the DTS.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114513.1098844-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add node for user push button.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114332.1098482-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add node for the user led.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114332.1098482-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Enable USB3 OTG and it's related PHY node. And the PHY will
also be shared with the upcoming DisplayPort controller.
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20250223100757.73531-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
