| Age | Commit message (Collapse) | Author |
|---|
|
Use gpiod_set_value_cansleep() instead of gpiod_set_value()
to fix the below call trace in the boot log:
[ 5.690534] Call trace:
[ 5.690536] gpiod_set_value+0x40/0xa4
[ 5.690540] anx7625_runtime_pm_resume+0xa0/0x324 [anx7625]
[ 5.690545] __rpm_callback+0x48/0x1d8
[ 5.690549] rpm_callback+0x6c/0x78
Certain GPIO controllers require access via message-based buses
such as I2C or SPI, which may cause the GPIOs to enter a sleep
state. Therefore, use the gpiod_set_value_cansleep().
Signed-off-by: Ayushi Makhija <quic_amakhija@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250505094245.2660750-7-quic_amakhija@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
In the anx7625_sink_detect(), the device is checked to see
if it is a panel bridge, and it always sends a "connected"
status to the connector. When adding the DP port on port 1 of the
anx7625, it incorrectly treats it as a panel bridge and sends an
always "connected" status. Instead of checking the status on the
panel bridge, it's better to check the hpd_status for connectors
that supports hot-plugging. This way, it verifies the hpd_status
variable before sending the status to the connector.
In case of eDP, anx7625_bridge_detect() will not get called because
the bridge->ops condition in anx7625_link_bridge() will not be
satisfied. Since anx7625_sink_detect() is called from
anx7625_bridge_detect(), this results in the sink_detect logic not
being executed for eDP.
Signed-off-by: Ayushi Makhija <quic_amakhija@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250505094245.2660750-6-quic_amakhija@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The anx7625_link_bridge() checks if a device is not a panel
bridge and add DRM_BRIDGE_OP_HPD and DRM_BRIDGE_OP_DETECT
flags to the drm_bridge->ops. However, on port 1 of the anx7625
bridge, any device added is always treated as a panel bridge,
preventing connector_detect() from being called. To resolve
this, instead of just checking if it is a panel bridge, verify
the type of device based on aux whether it is a DisplayPort or
eDP panel. If the device is not of the eDP type, add
DRM_BRIDGE_OP_HPD and DRM_BRIDGE_OP_DETECT flags to the to
the drm_bridge->ops.
Signed-off-by: Ayushi Makhija <quic_amakhija@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250505094245.2660750-5-quic_amakhija@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
When the device enters the suspend state, it prevents
HPD interrupts from occurring. To address this, implement
.hpd_enable() and .hpd_disable() callbacks functions of
the drm_bridge.
Signed-off-by: Ayushi Makhija <quic_amakhija@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250505094245.2660750-4-quic_amakhija@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
This is the new API for allocating DRM bridges.
These two drivers are tangled together by the ldb_add_bridge_helper(), so
they are converted at once.
They also have a similar design, each embedding an array of channels in
their main struct, and each channel embeds a drm_bridge. This prevents
dynamic, refcount-based deallocation of the bridges.
To make the new, dynamic bridge allocation possible:
* change the array of channels into an array of channel pointers
* allocate each channel using devm_drm_bridge_alloc()
* adapt ldb_add_bridge_helper() to not set the funcs pointer
(now done by devm_drm_bridge_alloc())
* adapt the code wherever using the channels
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Liu Ying <victor.liu@nxp.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250424-drm-bridge-convert-to-alloc-api-v2-31-8f91a404d86b@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
This is the new API for allocating DRM bridges.
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250424-drm-bridge-convert-to-alloc-api-v2-13-8f91a404d86b@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
This is the new API for allocating DRM bridges.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250424-drm-bridge-convert-to-alloc-api-v2-12-8f91a404d86b@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
This is the new API for allocating DRM bridges.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250424-drm-bridge-convert-to-alloc-api-v2-11-8f91a404d86b@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
This is the new API for allocating DRM bridges.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250424-drm-bridge-convert-to-alloc-api-v2-7-8f91a404d86b@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
This is the new API for allocating DRM bridges.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250424-drm-bridge-convert-to-alloc-api-v2-6-8f91a404d86b@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
This is the new API for allocating DRM bridges.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Andy Yan <andyshrk@163.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250424-drm-bridge-convert-to-alloc-api-v2-3-8f91a404d86b@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
If lt9611uxc_audio_init() fails, some resources still need to be released
before returning the error code.
Use the existing error handling path.
Fixes: 0cbbd5b1a012 ("drm: bridge: add support for lontium LT9611UXC bridge")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/f167608e392c6b4d7d7f6e45e3c21878feb60cbd.1744958833.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Follow the example of other drivers and ignore return values of the
drm_panel_prepare() / unprepare() / enable() / disable() calls. There is
no possible error recovery, so the driver just logs a message.
Tested-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250401-panel-return-void-v1-6-93e1be33dc8d@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The analogix_dp_prepare_panel() is now only calling a corresponding
drm_panel function. Inline it to simplify the code.
Tested-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250401-panel-return-void-v1-5-93e1be33dc8d@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The analogix_dp_prepare_panel() function is called from bridge's
atomic_pre_enable() and atomic_post_disable() callbacks, which can not
happen simultaneously. Drop the useless mutex.
Tested-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250401-panel-return-void-v1-4-93e1be33dc8d@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The dp->panel_is_modeset is now a write-only field. Drop it completely.
Tested-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250401-panel-return-void-v1-3-93e1be33dc8d@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
After previous cleanup all calling sites pass true as is_modeset_prepare
argument to analogix_dp_prepare_panel(). Drop dead code depending on
that argument being false.
Tested-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250401-panel-return-void-v1-2-93e1be33dc8d@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The analogix_dp_prepare_panel() returns immediately if there is no
attached panel. Drop several calls to this function which are performed
when dp->plat_data->panel is NULL.
Tested-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250401-panel-return-void-v1-1-93e1be33dc8d@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Expand enum analogix_dp_devtype with RK3588_EDP, and add max_link_rate
and max_lane_count configs for it.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/20250310104114.2608063-11-damon.ding@rock-chips.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Add analogix_dpaux_wait_hpd_asserted() to help confirm the HPD state
before doing AUX transfers.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250310104114.2608063-8-damon.ding@rock-chips.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The main modification is moving the DP AUX initialization from function
analogix_dp_bind() to analogix_dp_probe(). In order to get the EDID of
eDP panel during probing, it is also needed to advance PM operations to
ensure that eDP controller and phy are prepared for AUX transmission.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250310104114.2608063-7-damon.ding@rock-chips.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
&analogix_dp_device.aux
Add two new functions: one to find &analogix_dp_device.plat_data via
&drm_dp_aux, and the other to get &analogix_dp_device.aux. Both of them
serve for the function of getting panel from DP AUX bus, which is why
they are included in a single commit.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/20250310104114.2608063-6-damon.ding@rock-chips.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Add support to configurate link rate, lane count, voltage swing and
pre-emphasis with phy_configure(). It is helpful in application scenarios
where analogix controller is mixed with the phy of other vendors.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/20250310104114.2608063-4-damon.ding@rock-chips.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
analogix_dp_bind()/analogix_dp_unbind()
Remove the check related to CONFIG_PM in order to make the code more
concise, as the CONFIG_PM should be a required option for many drivers.
In addition, it is preferable to use devm_pm_runtime_enable() instead of
manually invoking pm_runtime_enable() followed by pm_runtime_disable().
Suggested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/20250310104114.2608063-3-damon.ding@rock-chips.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
disable_irq()
The IRQF_NO_AUTOEN can be used for the drivers that don't want
interrupts to be enabled automatically via devm_request_threaded_irq().
Using this flag can provide be more robust compared to the way of
calling disable_irq() after devm_request_threaded_irq() without the
IRQF_NO_AUTOEN flag.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/20250310104114.2608063-2-damon.ding@rock-chips.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
It is not recommended for drivers to include UAPI header
directly.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250411115941.318558-1-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The aux bridge uses devm_drm_of_get_bridge() from the panel bridge (and
correctly selects DRM_PANEL_BRIDGE). However panel bridge is not a
separate module, it is compiled into the drm_kms_helper.o. Select
DRM_KMS_HELPER too to express this dependency.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250411-aux-select-kms-v1-1-c4276f905a56@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The anx7625 driver is open coding what devm_pm_runtime_enable() does.
Switch to the common helper instead.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250409093814.3977025-1-wenst@chromium.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
|
|
As pointed out by Laurent, OP bits are supposed to describe operations.
Split DRM_BRIDGE_OP_HDMI_AUDIO from DRM_BRIDGE_OP_HDMI instead of
overloading DRM_BRIDGE_OP_HDMI.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20250314-dp-hdmi-audio-v6-1-dbd228fa73d7@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Backmerging to get v6.15-rc1 into drm-misc-next. Also fixes a
build issue when enabling CONFIG_DRM_SCHED_KUNIT_TEST.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
Allow this bridge to be removable without dangling pointers and
use-after-free, together with proper use of drm_bridge_get() and _put() by
consumers.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250326-drm-bridge-refcount-v9-5-5e0661fe1f84@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
Allow this bridge to be removable without dangling pointers and
use-after-free, together with proper use of drm_bridge_get() and _put() by
consumers.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250326-drm-bridge-refcount-v9-4-5e0661fe1f84@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer cleanups from Thomas Gleixner:
"A set of final cleanups for the timer subsystem:
- Convert all del_timer[_sync]() instances over to the new
timer_delete[_sync]() API and remove the legacy wrappers.
Conversion was done with coccinelle plus some manual fixups as
coccinelle chokes on scoped_guard().
- The final cleanup of the hrtimer_init() to hrtimer_setup()
conversion.
This has been delayed to the end of the merge window, so that all
patches which have been merged through other trees are in mainline
and all new users are catched.
Doing this right before rc1 ensures that new code which is merged post
rc1 is not introducing new instances of the original functionality"
* tag 'timers-cleanups-2025-04-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tracing/timers: Rename the hrtimer_init event to hrtimer_setup
hrtimers: Rename debug_init_on_stack() to debug_setup_on_stack()
hrtimers: Rename debug_init() to debug_setup()
hrtimers: Rename __hrtimer_init_sleeper() to __hrtimer_setup_sleeper()
hrtimers: Remove unnecessary NULL check in hrtimer_start_range_ns()
hrtimers: Make callback function pointer private
hrtimers: Merge __hrtimer_init() into __hrtimer_setup()
hrtimers: Switch to use __htimer_setup()
hrtimers: Delete hrtimer_init()
treewide: Convert new and leftover hrtimer_init() users
treewide: Switch/rename to timer_delete[_sync]()
|
|
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Use the common dp link power up/down helpers to avoid duplicating code.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318063452.4983-5-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Use the common dp link power up/down helpers to avoid duplicating code.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318063452.4983-4-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Use the common dp link power up/down helpers to avoid duplicating code.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318063452.4983-3-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Use the common dp link power up/down helpers to avoid duplicating code.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318063452.4983-2-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
This is a RGB to HDMI bridge, so set the bridge type accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250326101124.4031874-1-alexander.stein@ew.tq-group.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
This fails to build without the KMS helper functions:
x86_64-linux-ld: drivers/gpu/drm/bridge/tda998x_drv.o: in function `tda998x_detect_work':
tda998x_drv.c:(.text+0x4e6): undefined reference to `drm_kms_helper_hotplug_event'
x86_64-linux-ld: drivers/gpu/drm/bridge/tda998x_drv.o: in function `tda998x_bind':
tda998x_drv.c:(.text.unlikely+0x33): undefined reference to `drm_simple_encoder_init'
x86_64-linux-ld: drivers/gpu/drm/bridge/tda998x_drv.o:(.rodata+0x584): undefined reference to `drm_atomic_helper_connector_reset'
x86_64-linux-ld: drivers/gpu/drm/bridge/tda998x_drv.o:(.rodata+0x590): undefined reference to `drm_helper_probe_single_connector_modes'
x86_64-linux-ld: drivers/gpu/drm/bridge/tda998x_drv.o:(.rodata+0x5a4): undefined reference to `drm_atomic_helper_connector_duplicate_state'
x86_64-linux-ld: drivers/gpu/drm/bridge/tda998x_drv.o:(.rodata+0x5a8): undefined reference to `drm_atomic_helper_connector_destroy_state'
Select the missing symbol and fix up the broken whitespace.
Fixes: 325ba852d148 ("drm/i2c: move TDA998x driver under drivers/gpu/drm/bridge")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250324210824.3094660-1-arnd@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
At present, the DSI mode configuration check happens during the
_atomic_enable() phase, which is not really the best place for this.
Moreover, if the mode is not valid, the driver gives a warning and
continues the hardware configuration.
Move the DSI mode configuration check to _atomic_check() instead, which
can properly report back any invalid mode, before the _enable phase even
begins.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-10-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Add support for the input format negotiation hook, that uses the helper
drm_mipi_dsi_get_input_bus_fmt() for dsi hosts, to figure out the
required input format.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-9-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Instead of manually finding the next bridge/panel, and maintaining the
panel-bridge (in-case the next entity is a panel), switch to using the
automatically managing devm_drm_of_get_bridge() API.
Drop the drm_panel support completely from the driver while at it.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-7-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Once the DSI Link and DSI Phy are initialized, the code needs to wait
for Clk and Data Lanes to be ready, before continuing configuration.
This is in accordance with the DSI Start-up procedure, found in the
Technical Reference Manual of Texas Instrument's J721E SoC[0] which
houses this DSI TX controller.
If the previous bridge (or crtc/encoder) are configured pre-maturely,
the input signal FIFO gets corrupt. This introduces a color-shift on the
display.
Allow the driver to wait for the clk and data lanes to get ready during
DSI enable.
[0]: See section 12.6.5.7.3 "Start-up Procedure" in J721E SoC TRM
TRM Link: http://www.ti.com/lit/pdf/spruil1
Fixes: e19233955d9e ("drm/bridge: Add Cadence DSI driver")
Cc: stable@vger.kernel.org
Tested-by: Dominik Haller <d.haller@phytec.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-6-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Check for the return value of the phy_mipi_dphy_get_default_config()
call, and in case of an error, return back the same.
Fixes: fced5a364dee ("drm/bridge: cdns: Convert to phy framework")
Cc: stable@vger.kernel.org
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-5-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The crtc_* mode parameters do not get generated (duplicated in this
case) from the regular parameters before the mode validation phase
begins.
The rest of the code conditionally uses the crtc_* parameters only
during the bridge enable phase, but sticks to the regular parameters
for mode validation. In this singular instance, however, the driver
tries to use the crtc_clock parameter even during the mode validation,
causing the validation to fail.
Allow the D-Phy config checks to use mode->clock instead of
mode->crtc_clock during mode_valid checks, like everywhere else in the
driver.
Fixes: fced5a364dee ("drm/bridge: cdns: Convert to phy framework")
Cc: stable@vger.kernel.org
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-4-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The driver code doesn't have a Phy de-initialization path as yet, and so
it does not clear the phy_initialized flag while suspending. This is a
problem because after resume the driver looks at this flag to determine
if a Phy re-initialization is required or not. It is in fact required
because the hardware is resuming from a suspend, but the driver does not
carry out any re-initialization causing the D-Phy to not work at all.
Call the counterparts of phy_init() and phy_power_on(), that are
phy_exit() and phy_power_off(), from _bridge_post_disable(), and clear
the flags so that the Phy can be initialized again when required.
Fixes: fced5a364dee ("drm/bridge: cdns: Convert to phy framework")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-3-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Fix the OF node pointer passed to the of_drm_find_bridge() call to find
the next bridge in the display chain.
The code to find the next panel (and create its panel-bridge) works
fine, but to find the next (non-panel) bridge does not.
To find the next bridge in the pipeline, we need to pass "np" - the OF
node pointer of the next entity in the devicetree chain. Passing
"of_node" to of_drm_find_bridge (which is what the code does currently)
will fetch the bridge for the cdns-dsi which is not what's required.
Fix that.
Fixes: e19233955d9e ("drm/bridge: Add Cadence DSI driver")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-2-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250312090132.1624445-1-nichen@iscas.ac.cn
|
|
drm_dp_dpcd_read_link_status() follows the "return error code or number
of bytes read" protocol, with the code returning less bytes than
requested in case of some errors. However most of the drivers
interpreted that as "return error code in case of any error". Switch
drm_dp_dpcd_read_link_status() to drm_dp_dpcd_read_data() and make it
follow that protocol too.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250324-drm-rework-dpcd-access-v4-2-e80ff89593df@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
