summaryrefslogtreecommitdiff
path: root/drivers/net/dsa/b53
AgeCommit message (Collapse)Author
2025-05-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Cross-merge networking fixes after downstream PR (net-6.15-rc7). Conflicts: tools/testing/selftests/drivers/net/hw/ncdevmem.c 97c4e094a4b2 ("tests/ncdevmem: Fix double-free of queue array") 2f1a805f32ba ("selftests: ncdevmem: Implement devmem TCP TX") https://lore.kernel.org/20250514122900.1e77d62d@canb.auug.org.au Adjacent changes: net/core/devmem.c net/core/devmem.h 0afc44d8cdf6 ("net: devmem: fix kernel panic when netlink socket close after module unload") bd61848900bf ("net: devmem: Implement TX path") Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-13net: dsa: b53: prevent standalone from trying to forward to other portsJonas Gorski
When bridged ports and standalone ports share a VLAN, e.g. via VLAN uppers, or untagged traffic with a vlan unaware bridge, the ASIC will still try to forward traffic to known FDB entries on standalone ports. But since the port VLAN masks prevent forwarding to bridged ports, this traffic will be dropped. This e.g. can be observed in the bridge_vlan_unaware ping tests, where this breaks pinging with learning on. Work around this by enabling the simplified EAP mode on switches supporting it for standalone ports, which causes the ASIC to redirect traffic of unknown source MAC addresses to the CPU port. Since standalone ports do not learn, there are no known source MAC addresses, so effectively this redirects all incoming traffic to the CPU port. Fixes: ff39c2d68679 ("net: dsa: b53: Add bridge support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://patch.msgid.link/20250508091424.26870-1-jonas.gorski@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2025-05-12net: dsa: b53: implement setting ageing timeJonas Gorski
b53 supported switches support configuring ageing time between 1 and 1,048,575 seconds, so add an appropriate setter. This allows b53 to pass the FDB learning test for both vlan aware and vlan unaware bridges. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250510092211.276541-1-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-07net: dsa: b53: do not set learning and unicast/multicast on upJonas Gorski
When a port gets set up, b53 disables learning and enables the port for flooding. This can undo any bridge configuration on the port. E.g. the following flow would disable learning on a port: $ ip link add br0 type bridge $ ip link set sw1p1 master br0 <- enables learning for sw1p1 $ ip link set br0 up $ ip link set sw1p1 up <- disables learning again Fix this by populating dsa_switch_ops::port_setup(), and set up initial config there. Fixes: f9b3827ee66c ("net: dsa: b53: Support setting learning on port") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-12-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-07net: dsa: b53: fix learning on VLAN unaware bridgesJonas Gorski
When VLAN filtering is off, we configure the switch to forward, but not learn on VLAN table misses. This effectively disables learning while not filtering. Fix this by switching to forward and learn. Setting the learning disable register will still control whether learning actually happens. Fixes: dad8d7c6452b ("net: dsa: b53: Properly account for VLAN filtering") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-11-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-07net: dsa: b53: fix toggling vlan_filteringJonas Gorski
To allow runtime switching between vlan aware and vlan non-aware mode, we need to properly keep track of any bridge VLAN configuration. Likewise, we need to know when we actually switch between both modes, to not have to rewrite the full VLAN table every time we update the VLANs. So keep track of the current vlan_filtering mode, and on changes, apply the appropriate VLAN configuration. Fixes: 0ee2af4ebbe3 ("net: dsa: set configure_vlan_while_not_filtering to true by default") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-10-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-07net: dsa: b53: do not program vlans when vlan filtering is offJonas Gorski
Documentation/networking/switchdev.rst says: - with VLAN filtering turned off: the bridge is strictly VLAN unaware and its data path will process all Ethernet frames as if they are VLAN-untagged. The bridge VLAN database can still be modified, but the modifications should have no effect while VLAN filtering is turned off. This breaks if we immediately apply the VLAN configuration, so skip writing it when vlan_filtering is off. Fixes: 0ee2af4ebbe3 ("net: dsa: set configure_vlan_while_not_filtering to true by default") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-9-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-07net: dsa: b53: do not allow to configure VLAN 0Jonas Gorski
Since we cannot set forwarding destinations per VLAN, we should not have a VLAN 0 configured, as it would allow untagged traffic to work across ports on VLAN aware bridges regardless if a PVID untagged VLAN exists. So remove the VLAN 0 on join, an re-add it on leave. But only do so if we have a VLAN aware bridge, as without it, untagged traffic would become tagged with VID 0 on a VLAN unaware bridge. Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-8-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-07net: dsa: b53: always rejoin default untagged VLAN on bridge leaveJonas Gorski
While JOIN_ALL_VLAN allows to join all VLANs, we still need to keep the default VLAN enabled so that untagged traffic stays untagged. So rejoin the default VLAN even for switches with JOIN_ALL_VLAN support. Fixes: 48aea33a77ab ("net: dsa: b53: Add JOIN_ALL_VLAN support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-7-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-07net: dsa: b53: fix VLAN ID for untagged vlan on bridge leaveJonas Gorski
The untagged default VLAN is added to the default vlan, which may be one, but we modify the VLAN 0 entry on bridge leave. Fix this to use the correct VLAN entry for the default pvid. Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-6-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-07net: dsa: b53: fix flushing old pvid VLAN on pvid changeJonas Gorski
Presumably the intention here was to flush the VLAN of the old pvid, not the added VLAN again, which we already flushed before. Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-5-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-07net: dsa: b53: fix clearing PVID of a portJonas Gorski
Currently the PVID of ports are only set when adding/updating VLANs with PVID set or removing VLANs, but not when clearing the PVID flag of a VLAN. E.g. the following flow $ ip link add br0 type bridge vlan_filtering 1 $ ip link set sw1p1 master bridge $ bridge vlan add dev sw1p1 vid 10 pvid untagged $ bridge vlan add dev sw1p1 vid 10 untagged Would keep the PVID set as 10, despite the flag being cleared. Fix this by checking if we need to unset the PVID on vlan updates. Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-4-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-07net: dsa: b53: keep CPU port always tagged againJonas Gorski
The Broadcom management header does not carry the original VLAN tag state information, just the ingress port, so for untagged frames we do not know from which VLAN they originated. Therefore keep the CPU port always tagged except for VLAN 0. Fixes the following setup: $ ip link add br0 type bridge vlan_filtering 1 $ ip link set sw1p1 master br0 $ bridge vlan add dev br0 pvid untagged self $ ip link add sw1p2.10 link sw1p2 type vlan id 10 Where VID 10 would stay untagged on the CPU port. Fixes: 2c32a3d3c233 ("net: dsa: b53: Do not force CPU to be always tagged") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-3-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-05-07net: dsa: b53: allow leaky reserved multicastJonas Gorski
Allow reserved multicast to ignore VLAN membership so STP and other management protocols work without a PVID VLAN configured when using a vlan aware bridge. Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-2-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-04-16net: b53: enable BPDU reception for management portJonas Gorski
For STP to work, receiving BPDUs is essential, but the appropriate bit was never set. Without GC_RX_BPDU_EN, the switch chip will filter all BPDUs, even if an appropriate PVID VLAN was setup. Fixes: ff39c2d68679 ("net: dsa: b53: Add bridge support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Link: https://patch.msgid.link/20250414200434.194422-1-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-19net: dsa: b53: mdio: add support for BCM53101Torben Nielsen
BCM53101 is a ethernet switch, very similar to the BCM53115. Enable support for it, in the existing b53 dsa driver. Signed-off-by: Torben Nielsen <torben.nielsen@prevas.dk> Signed-off-by: Claus Stovgaard <claus.stovgaard@prevas.dk> Link: https://patch.msgid.link/20250217080503.1390282-1-claus.stovgaard@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-14net: remove phylink_pcs .neg_mode booleanRussell King (Oracle)
As all PCS are using the neg_mode parameter rather than the legacy an_mode, remove the ability to use the legacy an_mode. We remove the tests in the phylink code, unconditionally passing the PCS neg_mode parameter to PCS methods, and remove setting the flag from drivers. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tidPn-0040hd-2R@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-01-15net: phylink: pass neg_mode into .pcs_get_state() methodRussell King (Oracle)
Pass the current neg_mode into the .pcs_get_state() method. Update all users of phylink PCS. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/E1tXGeT-000Et3-4L@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-01-07net: dsa: b53/bcm_sf2: remove b53_get_mac_eee()Russell King (Oracle)
b53_get_mac_eee() is no longer called by the core DSA code. Remove it. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/E1tUll5-007Uyr-1U@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-12-11net: dsa: b53/bcm_sf2: implement .support_eee() methodRussell King (Oracle)
Implement the .support_eee() method to indicate that EEE is not supported by two switch variants, rather than making these checks in the .set_mac_eee() and .get_mac_eee() methods. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://patch.msgid.link/E1tL14E-006cZU-Nc@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-03net: dsa: use ethtool string helpersRosen Penev
These are the preferred way to copy ethtool strings. Avoids incrementing pointers all over the place. Signed-off-by: Rosen Penev <rosenp@gmail.com> (for hellcreek driver) Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Link: https://patch.msgid.link/20241028044828.1639668-1-rosenp@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-10-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Cross-merge networking fixes after downstream PR (net-6.12-rc3). No conflicts and no adjacent changes. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-10-08net: dsa: b53: fix jumbo frames on 10/100 portsJonas Gorski
All modern chips support and need the 10_100 bit set for supporting jumbo frames on 10/100 ports, so instead of enabling it only for 583XX enable it for everything except bcm63xx, where the bit is writeable, but does nothing. Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds without the bit set. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-10-08net: dsa: b53: allow lower MTUs on BCM5325/5365Jonas Gorski
While BCM5325/5365 do not support jumbo frames, they do support slightly oversized frames, so do not error out if requesting a supported MTU for them. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-10-08net: dsa: b53: fix max MTU for BCM5325/BCM5365Jonas Gorski
BCM5325/BCM5365 do not support jumbo frames, so we should not report a jumbo frame mtu for them. But they do support so called "oversized" frames up to 1536 bytes long by default, so report an appropriate MTU. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-10-08net: dsa: b53: fix max MTU for 1g switchesJonas Gorski
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload without ethernet headers. According to the datasheets maximum supported frame length for most gigabyte swithes is 9720 bytes, so convert that to the expected MTU when using VLAN tagged frames. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-10-08net: dsa: b53: fix jumbo frame mtu checkJonas Gorski
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the data payload size. Comparing these two meant that mtus between 1500 and 1518 did not trigger enabling jumbo frames. So instead compare the set mtu ETH_DATA_LEN, which is equal to JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN; Also do a check that the requested mtu is actually greater than the minimum length, else we do not need to enable jumbo frames. In practice this only introduced a very small range of mtus that did not work properly. Newer chips allow 2000 byte large frames by default, and older chips allow 1536 bytes long, which is equivalent to an mtu of 1514. So effectivly only mtus of 1515~1517 were broken. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-10-04net: dsa: Switch back to struct platform_driver::remove()Uwe Kleine-König
After commit 0edb555a65d1 ("platform: Make platform_driver::remove() return void") .remove() is (again) the right callback to implement for platform drivers. Convert all platform drivers below drivers/net/dsa to use .remove(), with the eventual goal to drop struct platform_driver::remove_new(). As .remove() and .remove_new() have the same prototypes, conversion is done by just changing the structure member name in the driver initializer. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/36da477cb9fa0bffec32d50c2cf3d18e94a0e7e3.1727949050.git.u.kleine-koenig@baylibre.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-10-02move asm/unaligned.h to linux/unaligned.hAl Viro
asm/unaligned.h is always an include of asm-generic/unaligned.h; might as well move that thing to linux/unaligned.h and include that - there's nothing arch-specific in that header. auto-generated by the following: for i in `git grep -l -w asm/unaligned.h`; do sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i done for i in `git grep -l -w asm-generic/unaligned.h`; do sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i done git mv include/asm-generic/unaligned.h include/linux/unaligned.h git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
2024-08-20net: dsa: b53: Use dev_err_probe()Florian Fainelli
Rather than print an error even when we get -EPROBE_DEFER, use dev_err_probe() to filter out those messages. Link: https://github.com/openwrt/openwrt/pull/11680 Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20240820004436.224603-1-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-07-18net: dsa: b53: Limit chip-wide jumbo frame config to CPU portsMartin Willi
Broadcom switches supported by the b53 driver use a chip-wide jumbo frame configuration. In the commit referenced with the Fixes tag, the setting is applied just for the last port changing its MTU. While configuring CPU ports accounts for tagger overhead, user ports do not. When setting the MTU for a user port, the chip-wide setting is reduced to not include the tagger overhead, resulting in an potentially insufficient chip-wide maximum frame size for the CPU port. As, by design, the CPU port MTU is adjusted for any user port change, apply the chip-wide setting only for CPU ports. This aligns the driver to the behavior of other switch drivers. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Suggested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Martin Willi <martin@strongswan.org> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-04-25net: dsa: b53: provide own phylink MAC operationsFlorian Fainelli
Convert b53 to provide its own phylink MAC operations, thus avoiding the shim layer in DSA's port.c Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240423183339.1368511-9-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25net: dsa: b53: Remove b53_adjust_link()Florian Fainelli
Only use the PHYLINK implementation from there on now that an equivalent configuration is applied to all of the switch ports. Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240423183339.1368511-8-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25net: dsa: b53: Call b53_eee_init() from b53_mac_link_up()Florian Fainelli
And make sure this is done for the MLO_AN_PHY case, where it actually makes sense, contrary to b53_adjust_link() which only did it for fixed-PHY configurations where it does not make sense. Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240423183339.1368511-7-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25net: dsa: b53: Configure RGMII for 531x5 and MII for 5325Florian Fainelli
Call b53_adjust_531x5_rgmii() and b53_adjust_5325_mii() from b53_phylink_mac_config() when we have a fixed PHY in preparation for removing b53_adjust_link(). Also move b53_adjust_63xx_rgmii() to b53_phylink_mac_config() where it logically belongs. Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240423183339.1368511-6-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25net: dsa: b53: Force flow control for BCM5301X CPU port(s)Florian Fainelli
Just like what b53_adjust_link() does, force flow control for the BCM5301X CPU port(s) by forcing rx_pause and tx_pause in b53_phylink_mac_link_up(). Preparatory step for getting rid of b53_adjust_link(). Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240423183339.1368511-5-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25net: dsa: b53: Introduce b53_adjust_5325_mii()Florian Fainelli
Takes care of doing the 5325 switch series specific MII programming and is called from b53_adjust_link() to allow the future removal of b53_adjust_link(). Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240423183339.1368511-4-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25net: dsa: b53: Introduce b53_adjust_531x5_rgmii()Florian Fainelli
Takes care of doing the 531x5 switch series specific RGMII programming and is called from b53_adjust_link() to allow the future removal of b53_adjust_link(). Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240423183339.1368511-3-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-04-25net: dsa: b53: Stop exporting b53_phylink_* routinesFlorian Fainelli
They are not used outside of the b53_common.c file, no need to be exported. Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240423183339.1368511-2-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-08net: dsa: b53: unexport and move b53_eee_enable_set()Vladimir Oltean
After commit f86ad77faf24 ("net: dsa: bcm_sf2: Utilize b53_{enable, disable}_port"), bcm_sf2.c no longer calls b53_eee_enable_set(), and all its callers are in b53_common.c. We also need to move it, because it is called within b53_common.c before its definition, and we want to avoid forward declarations. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20240206112527.4132299-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-07net: dsa: b53: remove eee_enabled/eee_active in b53_get_mac_eee()Russell King (Oracle)
b53_get_mac_eee() sets both eee_enabled and eee_active, and then returns zero. dsa_slave_get_eee(), which calls this function, will then continue to call phylink_ethtool_get_eee(), which will return -EOPNOTSUPP if there is no PHY present, otherwise calling phy_ethtool_get_eee() which in turn will call genphy_c45_ethtool_get_eee(). genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active with its own interpretation from the PHYs settings and negotiation result. Thus, when there is no PHY, dsa_slave_get_eee() will fail with -EOPNOTSUPP, meaning eee_enabled and eee_active will not be returned to userspace. When there is a PHY, eee_enabled and eee_active will be overwritten by phylib, making the setting of these members in b53_get_mac_eee() entirely unnecessary. Remove this code, thus simplifying b53_get_mac_eee(). Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/E1rWbNI-002cCz-4x@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-01-31ethtool: replace struct ethtool_eee with a new struct ethtool_keee on kernel ↵Heiner Kallweit
side In order to pass EEE link modes beyond bit 32 to userspace we have to complement the 32 bit bitmaps in struct ethtool_eee with linkmode bitmaps. Therefore, similar to ethtool_link_settings and ethtool_link_ksettings, add a struct ethtool_keee. In a first step it's an identical copy of ethtool_eee. This patch simply does a s/ethtool_eee/ethtool_keee/g for all users. No functional change intended. Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-10-24net: dsa: Use conduit and user termsFlorian Fainelli
Use more inclusive terms throughout the DSA subsystem by moving away from "master" which is replaced by "conduit" and "slave" which is replaced by "user". No functional changes. Acked-by: Rob Herring <robh@kernel.org> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20231023181729.1191071-2-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-09-20net: dsa: b53: Convert to platform remove callback returning voidUwe Kleine-König
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert these drivers from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-24net: dsa: use capital "OR" for multiple licenses in SPDXKrzysztof Kozlowski
Documentation/process/license-rules.rst and checkpatch expect the SPDX identifier syntax for multiple licenses to use capital "OR". Correct it to keep consistent format and avoid copy-paste issues. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Reviewed-by: FLorian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20230823085632.116725-1-krzysztof.kozlowski@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-26net: dsa: Explicitly include correct DT includesRob Herring
The DT of_device.h and of_platform.h date back to the separate of_platform_bus_type before it as merged into the regular platform bus. As part of that merge prepping Arm DT support 13 years ago, they "temporarily" include each other. They also include platform_device.h and of.h. As a result, there's a pretty much random mix of those include files used throughout the tree. In order to detangle these headers and replace the implicit includes with struct declarations, users need to explicitly include the correct includes. Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20230724211859.805481-1-robh@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-18net: dsa: remove legacy_pre_march2020 from driversRussell King (Oracle)
Since DSA no longer marks anything as phylink-legacy, there is now no need for DSA drivers to set this member to false. Remove all instances of this. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-06-22net: dsa: b53: update PCS driver to use neg_modeRussell King (Oracle)
Update B53's embedded PCS driver to use neg_mode, even though it makes no use of it or the "mode" argument. This makes the driver consistent with converted drivers. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/E1qA8Ee-00EaGL-Az@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Conflicts: drivers/net/ethernet/mediatek/mtk_ppe.c 3fbe4d8c0e53 ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting") 924531326e2d ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow") Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-03-27net: dsa: b53: mmap: add phy opsÁlvaro Fernández Rojas
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing B53_PORT_MII_PAGE registers which hangs the device. This access should be done through the MDIO Mux bus controller. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-07-15 22:36:42 +0000