| Age | Commit message (Collapse) | Author |
|---|
|
Provide support for the following devlink cmds:
-DEVLINK_CMD_REGION_GET
-DEVLINK_CMD_REGION_NEW
-DEVLINK_CMD_REGION_DEL
-DEVLINK_CMD_REGION_READ
ixgbe devlink region implementation, similarly to the ice one,
lets user to create snapshots of content of Non Volatile Memory,
content of Shadow RAM, and capabilities of the device.
For both NVM and SRAM regions provide .read() handler to let user
read their contents without the need to create full snapshots.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver should detect whether the device entered FW rollback
mode and then notify user with the dedicated message including
FW and NVM versions.
Even if the driver detected rollback mode, this should not result
in an probe error and the normal flow proceeds.
FW tries to rollback to "old" operational FW located in the
inactive NVM bank in cases when newly loaded FW exhibits faulty
behavior. If something goes wrong during boot the FW may switch
into rollback mode in an attempt to avoid recovery mode and stay
operational. After rollback is successful, the banks are swapped,
and the "rollback" bank becomes the active bank for the next reset.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add E610 specific function checking whether the FW API version
is compatible with the driver expectations.
The major API version should be less than or equal to the expected
API version. If not the driver won't be fully operational.
Check the minor version, and if it is more than two versions lesser
or greater than the expected version, print a message indicating
that the NVM or driver should be updated respectively.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The E610 adapters contain an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Co-developed-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Co-developed-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use the pldmfw library to implement device flash update for
the Intel ixgbe networking device driver specifically for E610 devices.
This support uses the devlink flash update interface.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset.
With this implementation, basic flash update for the E610 hardware is
supported.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Co-developed-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Co-developed-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add functions reading inactive versions from the inactive flash
bank.
Print stored versions for the content present in the inactive bank.
If there's pending update the versions reflect the ones which
are going to be loaded after reload. If there's no pending update
both running and stored are the same, which means there won't
be any NVM change on reload.
Co-developed-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Introduce 2 E610 specific callbacks implementations:
-ixgbe_start_hw_e610() which expands the regular .start_hw callback with
getting FW version information
-ixgbe_read_pba_string_e610() which gets Product Board Assembly string
Extend EEPROM ops with new .read_pba_string in order to distinguish
generic one and the E610 one.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Co-developed-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E610 devices give possibility to show more detailed info than the previous
boards.
Extend reporting NVM info with following pieces:
fw.mgmt.api -> version number of the API
fw.mgmt.build -> identifier of the source for the FW
fw.mgmt.srev -> number defining FW's security revision
fw.psid.api -> version defining the format of the flash contents
fw.undi.srev -> number defining OROM's security revision
fw.netlist -> version of the netlist module
fw.netlist.build -> first 4 bytes of the netlist hash
Co-developed-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Provide devlink .info_get() callback implementation to allow the
driver to report detailed version information. The following info
is reported:
"serial_number" -> The PCI DSN of the adapter
"fw.bundle_id" -> Unique identifier for the combined flash image
"fw.undi" -> Version of the Option ROM containing the UEFI driver
"board.id" -> The PBA ID string
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add an initial support for devlink interface to ixgbe driver.
Similarly to i40e driver the implementation doesn't enable
devlink to manage device-wide configuration. Devlink instance
is created for each physical function of PCIe device.
Create separate directory for devlink related ixgbe files
and use naming scheme similar to the one used in the ice driver.
Add a stub for Documentation, to be extended by further patches.
Change struct ixgbe_adapter allocation to be done by devlink (Przemek),
as suggested by Jiri.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Co-developed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
