summaryrefslogtreecommitdiff
path: root/drivers/pps
AgeCommit message (Collapse)Author
2025-04-05treewide: Convert new and leftover hrtimer_init() usersThomas Gleixner
hrtimer_setup() takes the callback function pointer as argument and initializes the timer completely. Replace hrtimer_init() and the open coded initialization of hrtimer::function with the new setup mechanism. Coccinelle scripted cleanup. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org>
2025-04-05treewide: Switch/rename to timer_delete[_sync]()Thomas Gleixner
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree over and remove the historical wrapper inlines. Conversion was done with coccinelle plus manual fixups where necessary. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org>
2025-04-01Merge tag 'char-misc-6.15-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char / misc / IIO driver updates from Greg KH: "Here is the big set of char, misc, iio, and other smaller driver subsystems for 6.15-rc1. Lots of stuff in here, including: - loads of IIO changes and driver updates - counter driver updates - w1 driver updates - faux conversions for some drivers that were abusing the platform bus interface - coresight driver updates - rust miscdevice binding updates based on real-world-use - other minor driver updates All of these have been in linux-next with no reported issues for quite a while" * tag 'char-misc-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits) samples: rust_misc_device: fix markup in top-level docs Coresight: Fix a NULL vs IS_ERR() bug in probe misc: lis3lv02d: convert to use faux_device tlclk: convert to use faux_device regulator: dummy: convert to use the faux device interface bus: mhi: host: Fix race between unprepare and queue_buf coresight: configfs: Constify struct config_item_type doc: iio: ad7380: describe offload support iio: ad7380: add support for SPI offload iio: light: Add check for array bounds in veml6075_read_int_time_ms iio: adc: ti-ads7924 Drop unnecessary function parameters staging: iio: ad9834: Use devm_regulator_get_enable() staging: iio: ad9832: Use devm_regulator_get_enable() iio: gyro: bmg160_spi: add of_match_table dt-bindings: iio: adc: Add i.MX94 and i.MX95 support iio: adc: ad7768-1: remove unnecessary locking Documentation: ABI: add wideband filter type to sysfs-bus-iio iio: adc: ad7768-1: set MOSI idle state to prevent accidental reset iio: adc: ad7768-1: Fix conversion result sign iio: adc: ad7124: Benefit of dev = indio_dev->dev.parent in ad7124_parse_channel_config() ...
2025-02-21pps: generators: Add PPS Generator TIO DriverSubramanian Mohan
The Intel Timed IO PPS generator driver outputs a PPS signal using dedicated hardware that is more accurate than software actuated PPS. The Timed IO hardware generates output events using the ART timer. The ART timer period varies based on platform type, but is less than 100 nanoseconds for all current platforms. Timed IO output accuracy is within 1 ART period. PPS output is enabled by writing '1' the 'enable' sysfs attribute. The driver uses hrtimers to schedule a wake-up 10 ms before each event (edge) target time. At wakeup, the driver converts the target time in terms of CLOCK_REALTIME to ART trigger time and writes this to the Timed IO hardware. The Timed IO hardware generates an event precisely at the requested system time without software involvement. Co-developed-by: Christopher Hall <christopher.s.hall@intel.com> Signed-off-by: Christopher Hall <christopher.s.hall@intel.com> Co-developed-by: Pandith N <pandith.n@intel.com> Signed-off-by: Pandith N <pandith.n@intel.com> Co-developed-by: Thejesh Reddy T R <thejesh.reddy.t.r@intel.com> Signed-off-by: Thejesh Reddy T R <thejesh.reddy.t.r@intel.com> Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com> Reviewed-by: Eddie Dong <eddie.dong@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Subramanian Mohan <subramanian.mohan@intel.com> Link: https://lore.kernel.org/r/20250219040618.70962-3-subramanian.mohan@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-21pps: generators: replace copy of pps-gen info struct with const pointerSubramanian Mohan
Some PPS generator drivers may need to retrieve a pointer to their internal data while executing the PPS generator enable() method. During the driver registration the pps_gen_device pointer is returned from the framework, and for that reason, there is difficulty in getting generator driver data back in the enable function. We won't be able to use container_of macro as it results in static assert, and we might end up in using static pointer. To solve the issue and to get back the generator driver data back, we should not copy the struct pps_gen_source_info within the struct pps_gen_device during the registration stage, but simply save the pointer of the driver one. In this manner, driver may get a pointer to their internal data as shown below: struct pps_gen_foo_data_s { ... struct pps_gen_source_info gen_info; struct pps_gen_device *pps_gen; ... }; static int __init pps_gen_foo_init(void) { struct pps_gen_foo_data_s *foo; ... foo->pps_gen = pps_gen_register_source(&foo->gen_info); ... } Then, in the enable() method, we can retrieve the pointer to the main struct by using the code below: static int pps_gen_foo_enable(struct pps_gen_device *pps_gen, bool enable) { struct pps_gen_foo_data_s *foo = container_of(pps_gen->info, struct pps_gen_foo_data_s, gen_info); ... } Signed-off-by: Rodolfo Giometti <giometti@enneenne.com> Tested-by: Subramanian Mohan <subramanian.mohan@intel.com> Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Subramanian Mohan <subramanian.mohan@intel.com> Link: https://lore.kernel.org/r/20250219040618.70962-2-subramanian.mohan@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-18pps: generators: pps_gen_parport: Switch to use hrtimer_setup()Nam Cao
hrtimer_setup() takes the callback function pointer as argument and initializes the timer completely. Replace hrtimer_init() and the open coded initialization of hrtimer::function with the new setup mechanism. Patch was created by using Coccinelle. Signed-off-by: Nam Cao <namcao@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Zack Rusin <zack.rusin@broadcom.com> Link: https://lore.kernel.org/all/4bf3bb22e21f27c58bb28690d856df913431e693.1738746904.git.namcao@linutronix.de
2025-01-10pps: clients: gpio: Bypass edge's direction check when not neededBastien Curutchet
In the IRQ handler, the GPIO's state is read to verify the direction of the edge that triggered the interruption before generating the PPS event. If a pulse is too short, the GPIO line can reach back its original state before this verification and the PPS event is lost. This check is needed when info->capture_clear is set because it needs interruptions on both rising and falling edges. When info->capture_clear is not set, interruption is triggered by one edge only so this check can be omitted. Add a warning if irq_handler is left without triggering any PPS event. Bypass the edge's direction verification when info->capture_clear is not set. Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Link: https://lore.kernel.org/r/20250108153012.514925-1-bastien.curutchet@bootlin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-01-08drivers pps/generators: add dummy PPS generatorRodolfo Giometti
This dummy PPS generator can be used for debugging and documentation purposes. Signed-off-by: Rodolfo Giometti <giometti@enneenne.com> Link: https://lore.kernel.org/r/20241108073115.759039-3-giometti@enneenne.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-01-08drivers pps: add PPS generators supportRodolfo Giometti
Sometimes one needs to be able not only to catch PPS signals but to produce them also. For example, running a distributed simulation, which requires computers' clock to be synchronized very tightly. This patch adds PPS generators class in order to have a well-defined interface for these devices. Signed-off-by: Rodolfo Giometti <giometti@enneenne.com> Link: https://lore.kernel.org/r/20241108073115.759039-2-giometti@enneenne.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-01-07pps: Fix a use-after-freeCalvin Owens
On a board running ntpd and gpsd, I'm seeing a consistent use-after-free in sys_exit() from gpsd when rebooting: pps pps1: removed ------------[ cut here ]------------ kobject: '(null)' (00000000db4bec24): is not initialized, yet kobject_put() is being called. WARNING: CPU: 2 PID: 440 at lib/kobject.c:734 kobject_put+0x120/0x150 CPU: 2 UID: 299 PID: 440 Comm: gpsd Not tainted 6.11.0-rc6-00308-gb31c44928842 #1 Hardware name: Raspberry Pi 4 Model B Rev 1.1 (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : kobject_put+0x120/0x150 lr : kobject_put+0x120/0x150 sp : ffffffc0803d3ae0 x29: ffffffc0803d3ae0 x28: ffffff8042dc9738 x27: 0000000000000001 x26: 0000000000000000 x25: ffffff8042dc9040 x24: ffffff8042dc9440 x23: ffffff80402a4620 x22: ffffff8042ef4bd0 x21: ffffff80405cb600 x20: 000000000008001b x19: ffffff8040b3b6e0 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 696e6920746f6e20 x14: 7369203a29343263 x13: 205d303434542020 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000 Call trace: kobject_put+0x120/0x150 cdev_put+0x20/0x3c __fput+0x2c4/0x2d8 ____fput+0x1c/0x38 task_work_run+0x70/0xfc do_exit+0x2a0/0x924 do_group_exit+0x34/0x90 get_signal+0x7fc/0x8c0 do_signal+0x128/0x13b4 do_notify_resume+0xdc/0x160 el0_svc+0xd4/0xf8 el0t_64_sync_handler+0x140/0x14c el0t_64_sync+0x190/0x194 ---[ end trace 0000000000000000 ]--- ...followed by more symptoms of corruption, with similar stacks: refcount_t: underflow; use-after-free. kernel BUG at lib/list_debug.c:62! Kernel panic - not syncing: Oops - BUG: Fatal exception This happens because pps_device_destruct() frees the pps_device with the embedded cdev immediately after calling cdev_del(), but, as the comment above cdev_del() notes, fops for previously opened cdevs are still callable even after cdev_del() returns. I think this bug has always been there: I can't explain why it suddenly started happening every time I reboot this particular board. In commit d953e0e837e6 ("pps: Fix a use-after free bug when unregistering a source."), George Spelvin suggested removing the embedded cdev. That seems like the simplest way to fix this, so I've implemented his suggestion, using __register_chrdev() with pps_idr becoming the source of truth for which minor corresponds to which device. But now that pps_idr defines userspace visibility instead of cdev_add(), we need to be sure the pps->dev refcount can't reach zero while userspace can still find it again. So, the idr_remove() call moves to pps_unregister_cdev(), and pps_idr now holds a reference to pps->dev. pps_core: source serial1 got cdev (251:1) <...> pps pps1: removed pps_core: unregistering pps1 pps_core: deallocating pps1 Fixes: d953e0e837e6 ("pps: Fix a use-after free bug when unregistering a source.") Cc: stable@vger.kernel.org Signed-off-by: Calvin Owens <calvin@wbinvd.org> Reviewed-by: Michal Schmidt <mschmidt@redhat.com> Link: https://lore.kernel.org/r/a17975fd5ae99385791929e563f72564edbcf28f.1731383727.git.calvin@wbinvd.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-12-01Get rid of 'remove_new' relic from platform driver structLinus Torvalds
The continual trickle of small conversion patches is grating on me, and is really not helping. Just get rid of the 'remove_new' member function, which is just an alias for the plain 'remove', and had a comment to that effect: /* * .remove_new() is a relic from a prototype conversion of .remove(). * New drivers are supposed to implement .remove(). Once all drivers are * converted to not use .remove_new any more, it will be dropped. */ This was just a tree-wide 'sed' script that replaced '.remove_new' with '.remove', with some care taken to turn a subsequent tab into two tabs to make things line up. I did do some minimal manual whitespace adjustment for places that used spaces to line things up. Then I just removed the old (sic) .remove_new member function, and this is the end result. No more unnecessary conversion noise. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2024-09-27[tree-wide] finally take no_llseek outAl Viro
no_llseek had been defined to NULL two years ago, in commit 868941b14441 ("fs: remove no_llseek") To quote that commit, At -rc1 we'll need do a mechanical removal of no_llseek - git grep -l -w no_llseek | grep -v porting.rst | while read i; do sed -i '/\<no_llseek\>/d' $i done would do it. Unfortunately, that hadn't been done. Linus, could you do that now, so that we could finally put that thing to rest? All instances are of the form .llseek = no_llseek, so it's obviously safe. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2024-09-03pps: add an error check in parport_attachMa Ke
In parport_attach, the return value of ida_alloc is unchecked, witch leads to the use of an invalid index value. To address this issue, index should be checked. When the index value is abnormal, the device should be freed. Found by code review, compile tested only. Cc: stable@vger.kernel.org Fixes: fb56d97df70e ("pps: client: use new parport device model") Signed-off-by: Ma Ke <make24@iscas.ac.cn> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Link: https://lore.kernel.org/r/20240828131814.3034338-1-make24@iscas.ac.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-25Merge tag 'driver-core-6.11-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here is the big set of driver core changes for 6.11-rc1. Lots of stuff in here, with not a huge diffstat, but apis are evolving which required lots of files to be touched. Highlights of the changes in here are: - platform remove callback api final fixups (Uwe took many releases to get here, finally!) - Rust bindings for basic firmware apis and initial driver-core interactions. It's not all that useful for a "write a whole driver in rust" type of thing, but the firmware bindings do help out the phy rust drivers, and the driver core bindings give a solid base on which others can start their work. There is still a long way to go here before we have a multitude of rust drivers being added, but it's a great first step. - driver core const api changes. This reached across all bus types, and there are some fix-ups for some not-common bus types that linux-next and 0-day testing shook out. This work is being done to help make the rust bindings more safe, as well as the C code, moving toward the end-goal of allowing us to put driver structures into read-only memory. We aren't there yet, but are getting closer. - minor devres cleanups and fixes found by code inspection - arch_topology minor changes - other minor driver core cleanups All of these have been in linux-next for a very long time with no reported problems" * tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits) ARM: sa1100: make match function take a const pointer sysfs/cpu: Make crash_hotplug attribute world-readable dio: Have dio_bus_match() callback take a const * zorro: make match function take a const pointer driver core: module: make module_[add|remove]_driver take a const * driver core: make driver_find_device() take a const * driver core: make driver_[create|remove]_file take a const * firmware_loader: fix soundness issue in `request_internal` firmware_loader: annotate doctests as `no_run` devres: Correct code style for functions that return a pointer type devres: Initialize an uninitialized struct member devres: Fix memory leakage caused by driver API devm_free_percpu() devres: Fix devm_krealloc() wasting memory driver core: platform: Switch to use kmemdup_array() driver core: have match() callback in struct bus_type take a const * MAINTAINERS: add Rust device abstractions to DRIVER CORE device: rust: improve safety comments MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER firmware: rust: improve safety comments ...
2024-07-03parport: Remove parport_driver.devmodelDr. David Alan Gilbert
'devmodel' hasn't actually been used since: 'commit 3275158fa52a ("parport: remove use of devmodel")' and everyone now has it set to true and has been fixed up; remove the flag. (There are still comments all over about it) Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/r/20240502154823.67235-4-linux@treblig.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-05-27pps: clients: gpio: Convert to platform remove callback returning voidUwe Kleine-König
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new(), which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Link: https://lore.kernel.org/r/f4b9402af72e5f285c8b0f068076a76418f653f5.1709886922.git.u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2024-04-29pps: remove usage of the deprecated ida_simple_xx() APIChristophe JAILLET
ida_alloc() and ida_free() should be preferred to the deprecated ida_simple_get() and ida_simple_remove(). This is less verbose. Link: https://lkml.kernel.org/r/9f681747d446b874952a892491387d79ffe565a9.1713089394.git.christophe.jaillet@wanadoo.fr Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Rodolfo Giometti <giometti@enneenne.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2024-03-07pps: use cflags-y instead of EXTRA_CFLAGSLukas Bulwahn
Commit f77bf01425b1 ("kbuild: introduce ccflags-y, asflags-y and ldflags-y") deprecates use of EXTRA_CFLAGS in the kernel build. This has been cleaned up in the whole kernel tree long ago, but this one single place must have been missed. Replace the EXTRA_CFLAGS use by the common pattern for such debug flags. No functional change. Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Link: https://lore.kernel.org/r/20240306120515.15711-1-lukas.bulwahn@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-03-17driver core: class: remove module * from class_create()Greg Kroah-Hartman
The module pointer in class_create() never actually did anything, and it shouldn't have been requred to be set as a parameter even if it did something. So just remove it and fix up all callers of the function in the kernel tree at the same time. Cc: "Rafael J. Wysocki" <rafael@kernel.org> Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty/serial: Make ->dcd_change()+uart_handle_dcd_change() status bool activeIlpo Järvinen
Convert status parameter for ->dcd_change() and uart_handle_dcd_change() to bool which matches to how the parameter is used. Rename status to active to better describe what the parameter means. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230117090358.4796-9-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-18pps: generators: pps_gen_parport: Switch to use module_parport_driver()Andy Shevchenko
Switch to use module_parport_driver() to reduce boilerplate code. Note, it doesn't matter when we check the module parameter. If it was writable we even would have more flexibility of changing it at runtime (when built-in the kernel) after this patch. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20220210134943.62026-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-04pps: clients: gpio: Propagate return value from pps_gpio_probeRobert Hancock
If the pps-gpio driver was probed prior to the GPIO device it uses, the devm_gpiod_get call returned an -EPROBE_DEFER error, but pps_gpio_probe replaced that error code with -EINVAL, causing the pps-gpio probe to fail and not be retried later. Propagate the error return value so that deferred probe works properly. Fixes: 161520451dfa (pps: new client driver using GPIO) Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: Rodolfo Giometti <giometti@enneenne.com> Link: https://lore.kernel.org/r/20220112205214.2060954-1-robert.hancock@calian.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-07-29pps: clients: parport: Switch to use module_parport_driver()Andy Shevchenko
Switch to use module_parport_driver() to reduce boilerplate code. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210607153729.58623-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13tty: no checking of tty_unregister_ldiscJiri Slaby
tty_unregister_ldisc now returns 0 = success. No need to check the return value. In fact, the users only warned if an error occured and didn't do anything useful anyway -- the ldisc module was unloaded in any case. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: William Hubbs <w.d.hubbs@gmail.com> Cc: Chris Brannon <chris@the-brannons.com> Cc: Kirk Reiser <kirk@reisers.ca> Cc: Samuel Thibault <samuel.thibault@ens-lyon.org> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Rodolfo Giometti <giometti@enneenne.com> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Link: https://lore.kernel.org/r/20210505091928.22010-19-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13tty: make tty_ldisc_ops a param in tty_unregister_ldiscJiri Slaby
Make tty_unregister_ldisc symmetric to tty_register_ldisc by accepting struct tty_ldisc_ops as a parameter instead of ldisc number. This avoids checking of the ldisc number bounds in tty_unregister_ldisc. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: William Hubbs <w.d.hubbs@gmail.com> Cc: Chris Brannon <chris@the-brannons.com> Cc: Kirk Reiser <kirk@reisers.ca> Cc: Samuel Thibault <samuel.thibault@ens-lyon.org> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Rodolfo Giometti <giometti@enneenne.com> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Link: https://lore.kernel.org/r/20210505091928.22010-17-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13tty: set tty_ldisc_ops::num staticallyJiri Slaby
There is no reason to pass the ldisc number to tty_register_ldisc separately. Just set it in the already defined tty_ldisc_ops in all the ldiscs. This simplifies tty_register_ldisc a bit too (no need to set the num member there). Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: William Hubbs <w.d.hubbs@gmail.com> Cc: Chris Brannon <chris@the-brannons.com> Cc: Kirk Reiser <kirk@reisers.ca> Cc: Samuel Thibault <samuel.thibault@ens-lyon.org> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Rodolfo Giometti <giometti@enneenne.com> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Link: https://lore.kernel.org/r/20210505091928.22010-15-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-04-26Merge tag 'tty-5.13-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty and serial driver updates from Greg KH: "Here is the big set of tty and serial driver updates for 5.13-rc1. Actually busy this release, with a number of cleanups happening: - much needed core tty cleanups by Jiri Slaby - removal of unused and orphaned old-style serial drivers. If anyone shows up with this hardware, it is trivial to restore these but we really do not think they are in use anymore. - fixes and cleanups from Johan Hovold on a number of termios setting corner cases that loads of drivers got wrong as well as removing unneeded code due to tty core changes from long ago that were never propagated out to the drivers - loads of platform-specific serial port driver updates and fixes - coding style cleanups and other small fixes and updates all over the tty/serial tree. All of these have been in linux-next for a while now with no reported issues" * tag 'tty-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits) serial: extend compile-test coverage serial: stm32: add FIFO threshold configuration dt-bindings: serial: 8250: update TX FIFO trigger level dt-bindings: serial: stm32: override FIFO threshold properties dt-bindings: serial: add RX and TX FIFO properties serial: xilinx_uartps: drop low-latency workaround serial: vt8500: drop low-latency workaround serial: timbuart: drop low-latency workaround serial: sunsu: drop low-latency workaround serial: sifive: drop low-latency workaround serial: txx9: drop low-latency workaround serial: sa1100: drop low-latency workaround serial: rp2: drop low-latency workaround serial: rda: drop low-latency workaround serial: owl: drop low-latency workaround serial: msm_serial: drop low-latency workaround serial: mpc52xx_uart: drop low-latency workaround serial: meson: drop low-latency workaround serial: mcf: drop low-latency workaround serial: lpc32xx_hs: drop low-latency workaround ...
2021-03-24pps: clients: gpio: Rearrange optional stuff in pps_gpio_setup()Andy Shevchenko
Rearrange optional stuff in pps_gpio_setup() so it will go after mandatory one and with reduced indentation. This will increase readability of the sources. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210318130321.24227-7-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-24pps: clients: gpio: Use struct device pointer directlyAndy Shevchenko
In most parts of the code the platform device is not used. Use struct device pointer directly to reduce code size and increase readability. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210318130321.24227-6-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-24pps: clients: gpio: Make use of device propertiesAndy Shevchenko
Device property API allows to gather device resources from different sources, such as ACPI. Convert the drivers to unleash the power of device property API. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210318130321.24227-5-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-24pps: clients: gpio: Get rid of legacy platform dataAndy Shevchenko
Platform data is a legacy interface to supply device properties to the driver. In this case we even don't have in-kernel users for it. Just remove it for good. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210318130321.24227-4-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-24pps: clients: gpio: Remove redundant condition in ->remove()Andy Shevchenko
The timer along with GPIO API are NULL-aware, there is no need to test against existing GPIO echo line. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210318130321.24227-3-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-24pps: clients: gpio: Use dev_err_probe() to avoid log noiseAndy Shevchenko
When GPIO APIs return -EPROBE_DEFER there is no need to print the message, especially taking into consideration that it may repeat several times. Use dev_err_probe() to avoid log noise in such cases. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210318130321.24227-2-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-24pps: clients: gpio: Bail out on error when requesting GPIO echo lineAndy Shevchenko
When requesting optional GPIO echo line, bail out on error, so user will know that something wrong with the existing property. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210318130321.24227-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-10tty: remove TTY_LDISC_MAGICJiri Slaby
First, it is never checked. Second, use of it as a debugging aid is at least questionable. With the current tools, I don't think anyone used this kind of thing for debugging purposes for years. On the top of that, e.g. serdev does not set this field of tty_ldisc_ops at all. So get rid of this legacy. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20210302062214.29627-8-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-14treewide: replace '---help---' in Kconfig files with 'help'Masahiro Yamada
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2019-07-16drivers/pps/pps.c: clear offset flags in PPS_SETPARAMS ioctlMiroslav Lichvar
The PPS assert/clear offset corrections are set by the PPS_SETPARAMS ioctl in the pps_ktime structs, which also contain flags. The flags are not initialized by applications (using the timepps.h header) and they are not used by the kernel for anything except returning them back in the PPS_GETPARAMS ioctl. Set the flags to zero to make it clear they are unused and avoid leaking uninitialized data of the PPS_SETPARAMS caller to other applications that have a read access to the PPS device. Link: http://lkml.kernel.org/r/20190702092251.24303-1-mlichvar@redhat.com Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Cc: Greg KH <greg@kroah.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-24treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 61Thomas Gleixner
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 675 mass ave cambridge ma 02139 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 441 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc) Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-14pps: pps-gpio PPS ECHO implementationTom Burkart
This patch implements the PPS ECHO functionality for pps-gpio, that sysfs claims is available already. Configuration is done via device tree bindings. No changes are made to userspace interfaces. This patch was originally written by Lukas Senger as part of a masters thesis project and modified for inclusion into the linux kernel by Tom Burkart. Link: http://lkml.kernel.org/r/20190324043305.6627-4-tom@aussec.com Signed-off-by: Tom Burkart <tom@aussec.com> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Lukas Senger <lukas@fridolin.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Rob Herring <robh@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-05-14pps: descriptor-based gpioTom Burkart
This patch changes the GPIO access for the pps-gpio driver from the integer based API to the descriptor based API. The integer based API is considered deprecated and the descriptor based API is the preferred way to access GPIOs as per Documentation/driver-api/gpio/intro.rst No changes are made to userspace interfaces. Link: http://lkml.kernel.org/r/20190324043305.6627-2-tom@aussec.com Signed-off-by: Tom Burkart <tom@aussec.com> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Reviewed-by: Philipp Zabel <philipp.zabel@gmail.com> Cc: Lukas Senger <lukas@fridolin.com> Cc: Rob Herring <robh@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-12-29Merge tag 'kconfig-v4.21' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kconfig updates from Masahiro Yamada: - support -y option for merge_config.sh to avoid downgrading =y to =m - remove S_OTHER symbol type, and touch include/config/*.h files correctly - fix file name and line number in lexer warnings - fix memory leak when EOF is encountered in quotation - resolve all shift/reduce conflicts of the parser - warn no new line at end of file - make 'source' statement more strict to take only string literal - rewrite the lexer and remove the keyword lookup table - convert to SPDX License Identifier - compile C files independently instead of including them from zconf.y - fix various warnings of gconfig - misc cleanups * tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits) kconfig: surround dbg_sym_flags with #ifdef DEBUG to fix gconf warning kconfig: split images.c out of qconf.cc/gconf.c to fix gconf warnings kconfig: add static qualifiers to fix gconf warnings kconfig: split the lexer out of zconf.y kconfig: split some C files out of zconf.y kconfig: convert to SPDX License Identifier kconfig: remove keyword lookup table entirely kconfig: update current_pos in the second lexer kconfig: switch to ASSIGN_VAL state in the second lexer kconfig: stop associating kconf_id with yylval kconfig: refactor end token rules kconfig: stop supporting '.' and '/' in unquoted words treewide: surround Kconfig file paths with double quotes microblaze: surround string default in Kconfig with double quotes kconfig: use T_WORD instead of T_VARIABLE for variables kconfig: use specific tokens instead of T_ASSIGN for assignments kconfig: refactor scanning and parsing "option" properties kconfig: use distinct tokens for type and default properties kconfig: remove redundant token defines kconfig: rename depends_list to comment_option_list ...
2018-12-22treewide: surround Kconfig file paths with double quotesMasahiro Yamada
The Kconfig lexer supports special characters such as '.' and '/' in the parameter context. In my understanding, the reason is just to support bare file paths in the source statement. I do not see a good reason to complicate Kconfig for the room of ambiguity. The majority of code already surrounds file paths with double quotes, and it makes sense since file paths are constant string literals. Make it treewide consistent now. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Ingo Molnar <mingo@kernel.org>
2018-11-27pps: using ERR_PTR instead of NULL while pps_register_source failsYueHaibing
pps_register_source() has keeps error codes in a local variable, but it does not make use of the code. This patch let it return the errcode in case of failure. Suggested-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14pps: generator: use new parport device modelSudip Mukherjee
Modify pps generator driver to use the new parallel port device model. Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14pps: client: use new parport device modelSudip Mukherjee
Modify pps client driver to use the new parallel port device model. In that process, added an index to mention the device number when we have more than one parallel port. Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-11vfs: do bulk POLL* -> EPOLL* replacementLinus Torvalds
This is the mindless scripted replacement of kernel use of POLL* variables as described by Al, done by this script: for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'` for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done done with de-mangling cleanups yet to come. NOTE! On almost all architectures, the EPOLL* constants have the same values as the POLL* constants do. But they keyword here is "almost". For various bad reasons they aren't the same, and epoll() doesn't actually work quite correctly in some cases due to this on Sparc et al. The next patch from Al will sort out the final differences, and we should be all done. Scripted-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-02-06pps: parport: use timespec64 instead of timespecArnd Bergmann
getnstimeofday() is deprecated, so I'm converting this to use ktime_get_real_ts64() as a safe replacement. I considered using ktime_get_real() instead, but since the algorithm here depends on the exact timing, I decided to introduce fewer changes and leave the code that determines the nanoseconds since the last seconds wrap untouched. It's not entirely clear to me whether we should also change the time base to CLOCK_BOOTTIME or CLOCK_TAI. With boottime, we would be independent of changes due to settimeofday() and only see the speed adjustment from the upstream clock source, with the downside of having the signal be at an arbirary offset from the start of the UTC second signal. With CLOCK_TAI, we would use the same offset from the UTC second as before and still suffer from settimeofday() adjustments, but would be less confused during leap seconds. Both boottime and tai only offer usable (i.e. avoiding ktime_t to timespec64 conversion) interfaces for ktime_t though, so either way, changing it wouldn't take significantly more work. CLOCK_MONOTONIC could be used with ktime_get_ts64(), but would lose synchronization across a suspend/resume cycle, which seems worse. Link: http://lkml.kernel.org/r/20180116171451.3095620-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Rodolfo Giometti <giometti@enneenne.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-11-28the rest of drivers/*: annotate ->poll() instancesAl Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2017-11-21treewide: setup_timer() -> timer_setup()Kees Cook
This converts all remaining cases of the old setup_timer() API into using timer_setup(), where the callback argument is the structure already holding the struct timer_list. These should have no behavioral changes, since they just change which pointer is passed into the callback with the same available pointers after conversion. It handles the following examples, in addition to some other variations. Casting from unsigned long: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... setup_timer(&ptr->my_timer, my_callback, ptr); and forced object casts: void my_callback(struct something *ptr) { ... } ... setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr); become: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... timer_setup(&ptr->my_timer, my_callback, 0); Direct function assignments: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... ptr->my_timer.function = my_callback; have a temporary cast added, along with converting the args: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback; And finally, callbacks without a data assignment: void my_callback(unsigned long data) { ... } ... setup_timer(&ptr->my_timer, my_callback, 0); have their argument renamed to verify they're unused during conversion: void my_callback(struct timer_list *unused) { ... } ... timer_setup(&ptr->my_timer, my_callback, 0); The conversion is done with the following Coccinelle script: spatch --very-quiet --all-includes --include-headers \ -I ./arch/x86/include -I ./arch/x86/include/generated \ -I ./include -I ./arch/x86/include/uapi \ -I ./arch/x86/include/generated/uapi -I ./include/uapi \ -I ./include/generated/uapi --include ./include/linux/kconfig.h \ --dir . \ --cocci-file ~/src/data/timer_setup.cocci @fix_address_of@ expression e; @@ setup_timer( -&(e) +&e , ...) // Update any raw setup_timer() usages that have a NULL callback, but // would otherwise match change_timer_function_usage, since the latter // will update all function assignments done in the face of a NULL // function initialization in setup_timer(). @change_timer_function_usage_NULL@ expression _E; identifier _timer; type _cast_data; @@ ( -setup_timer(&_E->_timer, NULL, _E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E->_timer, NULL, (_cast_data)_E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E._timer, NULL, &_E); +timer_setup(&_E._timer, NULL, 0); | -setup_timer(&_E._timer, NULL, (_cast_data)&_E); +timer_setup(&_E._timer, NULL, 0); ) @change_timer_function_usage@ expression _E; identifier _timer; struct timer_list _stl; identifier _callback; type _cast_func, _cast_data; @@ ( -setup_timer(&_E->_timer, _callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | _E->_timer@_stl.function = _callback; | _E->_timer@_stl.function = &_callback; | _E->_timer@_stl.function = (_cast_func)_callback; | _E->_timer@_stl.function = (_cast_func)&_callback; | _E._timer@_stl.function = _callback; | _E._timer@_stl.function = &_callback; | _E._timer@_stl.function = (_cast_func)_callback; | _E._timer@_stl.function = (_cast_func)&_callback; ) // callback(unsigned long arg) @change_callback_handle_cast depends on change_timer_function_usage@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; identifier _handle; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { ( ... when != _origarg _handletype *_handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg ) } // callback(unsigned long arg) without existing variable @change_callback_handle_cast_no_arg depends on change_timer_function_usage && !change_callback_handle_cast@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { + _handletype *_origarg = from_timer(_origarg, t, _timer); + ... when != _origarg - (_handletype *)_origarg + _origarg ... when != _origarg } // Avoid already converted callbacks. @match_callback_converted depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier t; @@ void _callback(struct timer_list *t) { ... } // callback(struct something *handle) @change_callback_handle_arg depends on change_timer_function_usage && !match_callback_converted && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; @@ void _callback( -_handletype *_handle +struct timer_list *t ) { + _handletype *_handle = from_timer(_handle, t, _timer); ... } // If change_callback_handle_arg ran on an empty function, remove // the added handler. @unchange_callback_handle_arg depends on change_timer_function_usage && change_callback_handle_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; identifier t; @@ void _callback(struct timer_list *t) { - _handletype *_handle = from_timer(_handle, t, _timer); } // We only want to refactor the setup_timer() data argument if we've found // the matching callback. This undoes changes in change_timer_function_usage. @unchange_timer_function_usage depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg && !change_callback_handle_arg@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type change_timer_function_usage._cast_data; @@ ( -timer_setup(&_E->_timer, _callback, 0); +setup_timer(&_E->_timer, _callback, (_cast_data)_E); | -timer_setup(&_E._timer, _callback, 0); +setup_timer(&_E._timer, _callback, (_cast_data)&_E); ) // If we fixed a callback from a .function assignment, fix the // assignment cast now. @change_timer_function_assignment depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_func; typedef TIMER_FUNC_TYPE; @@ ( _E->_timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -&_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)_callback; +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -&_callback; +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; ) // Sometimes timer functions are called directly. Replace matched args. @change_timer_function_calls depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression _E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_data; @@ _callback( ( -(_cast_data)_E +&_E->_timer | -(_cast_data)&_E +&_E._timer | -_E +&_E->_timer ) ) // If a timer has been configured without a data argument, it can be // converted without regard to the callback argument, since it is unused. @match_timer_function_unused_data@ expression _E; identifier _timer; identifier _callback; @@ ( -setup_timer(&_E->_timer, _callback, 0); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0L); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0UL); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0L); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0UL); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_timer, _callback, 0); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0L); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0UL); +timer_setup(&_timer, _callback, 0); | -setup_timer(_timer, _callback, 0); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0L); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0UL); +timer_setup(_timer, _callback, 0); ) @change_callback_unused_data depends on match_timer_function_unused_data@ identifier match_timer_function_unused_data._callback; type _origtype; identifier _origarg; @@ void _callback( -_origtype _origarg +struct timer_list *unused ) { ... when != _origarg } Signed-off-by: Kees Cook <keescook@chromium.org>
generated by cgit (git 2.34.1) at 2025-05-11 18:18:08 +0000