Age | Commit message (Collapse) | Author |
|
Qualcomm x1e80100 firmware sets the ownership of the RTC alarm to ADSP.
Thus writing to RTC alarm registers and receiving alarm interrupts is not
possible.
Add a qcom,no-alarm flag to support RTC on this platform.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20241015004945.3676-2-jonathan@marek.ca
[ johan: drop no_alarm flag and restructure probe() ]
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Sebastian Reichel <sre@kernel.org> # Lenovo T14s Gen6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250219134118.31017-5-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
On many Qualcomm platforms the PMIC RTC control and time registers are
read-only so that the RTC time can not be updated. Instead an offset
needs be stored in some machine-specific non-volatile memory, which the
driver can take into account.
On machines like the Lenovo ThinkPad X13s the PMIC RTC drifts about one
second every 3.5 hours, something which leads to repeated updates of the
offset when NTP synchronisation is enabled.
Reduce wear of the underlying flash storage (used for UEFI variables) by
deferring writes until shutdown in case they appear to be due to clock
drift.
As an example, deferring writes when the new offset differs up to 30 s
from the previous one reduces the number of writes on the X13s during a
ten day session with the machine not suspending for more than four days
in a row from up to 68 writes (every 3.5 h) to at most two (boot and
shutdown).
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Sebastian Reichel <sre@kernel.org> # Lenovo T14s Gen6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250219134118.31017-4-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
On many Qualcomm platforms the PMIC RTC control and time registers are
read-only so that the RTC time can not be updated. Instead an offset
needs be stored in some machine-specific non-volatile memory, which the
driver can take into account.
Add support for storing a 32-bit offset from the GPS time epoch in a
UEFI variable so that the RTC time can be set on such platforms.
The UEFI variable is
882f8c2b-9646-435f-8de5-f208ff80c1bd-RTCInfo
and holds a 12-byte structure where the first four bytes is a GPS time
offset in little-endian byte order.
Note that this format is not arbitrary as the variable is shared with
the UEFI firmware (and Windows).
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Sebastian Reichel <sre@kernel.org> # Lenovo T14s Gen6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250219134118.31017-3-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Switch to devm_device_init_wakeup to avoid a possible memory leak as wakeup
is never disabled.
Link: https://lore.kernel.org/r/20250303223600.1135142-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
probe must not fail after devm_rtc_register_device is successful because
the character device will be seen by userspace and may be opened right
away. Call it last to avoid opening the race window.
Link: https://lore.kernel.org/r/20250303223600.1135142-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use devm_pm_set_wake_irq, then the 'driver.remove()' could be cleaned up.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20250205-rtc-cleanup-v1-4-66165678e089@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
device_init_wakeup() second argument is a bool type. Use proper boolean
values when calling it to match the type and to produce unambiguous code
which is easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20241217071331.3607-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"New drivers:
- Amlogic A4 and A5 RTC
- Marvell 88PM886 PMIC RTC
- Renesas RTCA-3 for Renesas RZ/G3S
Driver updates:
- ab-eoz9: fix temperature and alarm support
- cmos: improve locking behaviour
- isl12022: add alarm support
- m48t59: improve epoch handling
- mt6359: add range
- rzn1: fix BCD conversions and simplify driver"
* tag 'rtc-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (38 commits)
rtc: ab-eoz9: don't fail temperature reads on undervoltage notification
rtc: rzn1: reduce register access
rtc: rzn1: drop superfluous wday calculation
m68k: mvme147, mvme16x: Adopt rtc-m48t59 platform driver
rtc: brcmstb-waketimer: don't include 'pm_wakeup.h' directly
rtc: m48t59: Use platform_data struct for year offset value
rtc: ab-eoz9: fix abeoz9_rtc_read_alarm
rtc: rv3028: fix RV3028_TS_COUNT type
rtc: rzn1: update Michel's email
rtc: rzn1: fix BCD to rtc_time conversion errors
rtc: amlogic-a4: fix compile error
rtc: amlogic-a4: drop error messages
MAINTAINERS: Add an entry for Amlogic RTC driver
rtc: support for the Amlogic on-chip RTC
dt-bindings: rtc: Add Amlogic A4 and A5 RTC
rtc: add driver for Marvell 88PM886 PMIC RTC
rtc: check if __rtc_read_time was successful in rtc_timer_do_work()
rtc: pcf8563: Switch to regmap
rtc: pcf8563: Sort headers alphabetically
rtc: abx80x: Fix WDT bit position of the status register
...
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/rtc to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241007205803.444994-6-u.kleine-koenig@baylibre.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-26-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
On many Qualcomm platforms the PMIC RTC control and time registers are
read-only so that the RTC time can not be updated. Instead an offset
needs be stored in some machine-specific non-volatile memory, which the
driver can take into account.
Add support for storing a 32-bit offset from the Epoch in an nvmem cell
so that the RTC time can be set on such platforms.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-18-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
For consistency with the rest of the driver, drop the last two error
messages for conditions that should only occur during development, if
ever.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-16-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Clean up local declarations somewhat by using the reverse xmas style
consistently throughout.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-15-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In preparation for adding support for setting the time by means of an
externally stored offset, refactor read_time() by adding a new helper
that can be used to retrieve the raw time as stored in the RTC.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-14-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The PMIC RTC registers are 32-bit so explicitly use u32 rather than
unsigned long for timestamps to reflect the hardware.
This will also help avoid unintentional range extensions when adding
support for managing an external offset.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-13-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Clean up the driver comments somewhat and remove obsolete, incorrect or
redundant ones.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-12-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Clean up the driver somewhat by renaming the driver-data alarm irq
variable by dropping the redundant "rtc" prefix.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-11-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Rename the driver-data struct device pointer by dropping the "rtc"
prefix which is both redundant and misleading (as this is a pointer to
the platform device and not the rtc class device).
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-10-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Clean up the time and alarm callback debugging by using a consistent and
succinct human-readable (i.e. non-raw) format.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-9-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use the unaligned le32 helpers instead of open coding when accessing the
time and alarm registers.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-8-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Drop the original register defines which have been unused since commit
c8d523a4b053 ("drivers/rtc/rtc-pm8xxx.c: rework to support pm8941 rtc").
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-7-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In the unlikely event that disabling the alarm and clearing the status
ever fails, return IRQ_NONE instead of IRQ_HANDLED.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-6-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Since commit c8d523a4b053 ("drivers/rtc/rtc-pm8xxx.c: rework to support
pm8941 rtc") which removed the shadow control register there is no need
for a driver lock.
Specifically, the rtc ops are serialised by rtc core and the interrupt
handler only unconditionally disables the alarm using the alarm_ctrl
register.
Note that since only the alarm enable bit of alarm_ctrl is used after
enabling the RTC at probe, the locking was not needed when doing open
coded read-modify-write cycles either.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-5-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Switch to using regmap_update_bits() instead of open coding
read-modify-write accesses.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-4-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Drop the unnecessary error messages after every spmi regmap access,
which are not expected to fail.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-3-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Make sure to disable the alarm before updating the four alarm time
registers to avoid spurious alarms during the update.
Note that the disable needs to be done outside of the ctrl_reg_lock
section to prevent a racing alarm interrupt from disabling the newly set
alarm when the lock is released.
Fixes: 9a9a54ad7aa2 ("drivers/rtc: add support for Qualcomm PMIC8xxx RTC")
Cc: stable@vger.kernel.org # 3.1
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20230202155448.6715-2-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The PM8018 compatible is always used with PM8921 fallback, so PM8018
compatible can be safely removed from device ID table
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220928-mdm9615-dt-schema-fixes-v5-2-bbb120c6766a@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Having !allow_set_time is equivalent to non-implemented set_time
function, which is normally represented with -ENODEV error in RTC
subsystem.
Today we are returning -EACCES error code, which is not considered
by RTC clients as a 'non implemented' feature, and which causes NTP
to retry hw clk sync (update_rtc) indefinitely.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1645090578-20734-1-git-send-email-loic.poulain@linaro.org
|
|
Attach the interrupt as a wake-irq to the device, so that:
- A corresponding wakeup source is created (and reported in e.g
/sys/kernel/debug/wakeup_sources).
- The power subsystem take cares of arming/disarming
irq-wake automatically on suspend/resume.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1645025082-6138-1-git-send-email-loic.poulain@linaro.org
|
|
Add the comaptible string for PMIC PMK8350.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1617976766-7852-2-git-send-email-skakit@codeaurora.org
|
|
It is redundant to do irqsave and irqrestore in hardIRQ context, where
it has been in a irq-disabled context.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1612355981-6764-3-git-send-email-tanxiaofei@huawei.com
|
|
ALARM_EN status is retained in PMIC register after device shutdown
if poweron_alarm is enabled. Read it to make sure the driver has
consistent value with the register status.
Signed-off-by: Guixiong Wei <guixiong@codeaurora.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1608809337-18852-1-git-send-email-guixiong@codeaurora.org
|
|
rtc_register_device() is a managed interface but it doesn't use devres
by itself - instead it marks an rtc_device as "registered" and the devres
callback for devm_rtc_allocate_device() takes care of resource release.
This doesn't correspond with the design behind devres where managed
structures should not be aware of being managed. The correct solution
here is to register a separate devres callback for unregistering the
device.
While at it: rename rtc_register_device() to devm_rtc_register_device()
and add it to the list of managed interfaces in devres.rst. This way we
can avoid any potential confusion of driver developers who may expect
there to exist a corresponding unregister function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201109163409.24301-8-brgl@bgdev.pl
|
|
Clear alarm register when alarm is not enabled otherwise the consumer
may still start alarm timer if it find the alarm register is not zero.
Signed-off-by: hankecai <hankecai@vivo.com>
Link: https://lore.kernel.org/r/APoAZgAaCEiRpKG6PlzreaqE.1.1584791417367.Hmail.hankecai@vivo.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
rtc_time64_to_tm never generates an invalid rtc_tm, stop validating it.
Link: https://lore.kernel.org/r/20200306073758.58050-4-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Call the 64bit versions of rtc_tm time conversion.
Link: https://lore.kernel.org/r/20200306073758.58050-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The pm8xxx are 32bit seconds counter.
Link: https://lore.kernel.org/r/20200306073758.58050-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
This allows further improvement of the driver. Also remove the unnecessary
error string as the core will already display error messages.
Link: https://lore.kernel.org/r/20200306073758.58050-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The change from u8 ctrl_reg to const struct pm8xxx_rtc_regs *regs; did not
properly update the kerneldoc comment. Fixes:
drivers/rtc/rtc-pm8xxx.c:64: warning: Function parameter or member 'regs' not described in 'pm8xxx_rtc'
Fixes: c8d523a4b053 ("drivers/rtc/rtc-pm8xxx.c: rework to support pm8941 rtc")
Link: https://lore.kernel.org/r/20191122102212.400158-7-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-rtc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-40-swboyd@chromium.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#1309693 ("Unintended sign extension")
Fixes: 9a9a54ad7aa2 ("drivers/rtc: add support for Qualcomm PMIC8xxx RTC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In order to set time in rtc, need to disable
rtc hw before writing into rtc registers.
Also fixes disabling of alarm while setting
rtc time.
Signed-off-by: Mohit Aggarwal <maggarwa@codeaurora.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
It is not necessary to print a message when the time is invalid as
userspace will already get an error (and an optional dev_dbg message).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In order to support RTC on Qualcomm MDM9615 SoC, add support for
the pm8018 rtc in rtc-pm8xxx driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into driver-core-next
Remove all .owner fields from platform drivers
|
|
Adds support for RTC device inside PM8941 PMIC. The RTC in this PMIC
have two register spaces. Thus the rtc-pm8xxx is slightly reworked to
reflect these differences.
The register set for different PMIC chips are selected on DT compatible
string base.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: simplify and fix locking in pm8xxx_rtc_set_time()]
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|