summaryrefslogtreecommitdiff
path: root/drivers/scsi/scsi_debug.c
AgeCommit message (Collapse)Author
2025-03-26Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds
Pull SCSI updates from James Bottomley: "Updates to the usual drivers (scsi_debug, ufs, lpfc, st, fnic, mpi3mr, mpt3sas) and the removal of cxlflash. The only non-trivial core change is an addition to unit attention handling to recognize UAs for power on/reset and new media so the tape driver can use it" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (107 commits) scsi: st: Tighten the page format heuristics with MODE SELECT scsi: st: ERASE does not change tape location scsi: st: Fix array overflow in st_setup() scsi: target: tcm_loop: Fix wrong abort tag scsi: lpfc: Restore clearing of NLP_UNREG_INP in ndlp->nlp_flag scsi: hisi_sas: Fixed failure to issue vendor specific commands scsi: fnic: Remove unnecessary NUL-terminations scsi: fnic: Remove redundant flush_workqueue() calls scsi: core: Use a switch statement when attaching VPD pages scsi: ufs: renesas: Add initialization code for R-Car S4-8 ES1.2 scsi: ufs: renesas: Add reusable functions scsi: ufs: renesas: Refactor 0x10ad/0x10af PHY settings scsi: ufs: renesas: Remove register control helper function scsi: ufs: renesas: Add register read to remove save/set/restore scsi: ufs: renesas: Replace init data by init code scsi: ufs: dt-bindings: renesas,ufs: Add calibration data scsi: mpi3mr: Task Abort EH Support scsi: storvsc: Don't report the host packet status as the hv status scsi: isci: Make most module parameters static scsi: megaraid_sas: Make most module parameters static ...
2025-03-02scsi: scsi_debug: Fix uninitialized variable useArnd Bergmann
It appears that a typo has made it into the newly added code drivers/scsi/scsi_debug.c:3035:3: error: variable 'len' is uninitialized when used here [-Werror,-Wuninitialized] 3035 | len += resp_compression_m_pg(ap, pcontrol, target, devip->tape_dce); | ^~~ Replace the '+=' with the intended '=' here. Fixes: 568354b24c7d ("scsi: scsi_debug: Add compression mode page for tapes") Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20250225095651.2636811-1-arnd@kernel.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24scsi: scsi_debug: Do not sleep in atomic sectionsBart Van Assche
Function stop_qc_helper() is called while the debug_scsi_cmd lock is held, and from here we may call cancel_work_sync(), which may sleep. Sleeping in atomic sections is not allowed. Hence change the cancel_work_sync() call into a cancel_work() call. However now it is not possible to know if the work callback is running when we return. This is relevant for eh_abort_handler handling, as the semantics of that callback are that success means that we do not keep a reference to the scsi_cmnd - now this is not possible. So return FAIL when we are unsure if the callback still running. Signed-off-by: Bart Van Assche <bvanassche@acm.org> jpg: return FAILED from scsi_debug_abort() when possible callback running Signed-off-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20250224115517.495899-5-john.g.garry@oracle.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24scsi: scsi_debug: Simplify command handlingBart Van Assche
Simplify command handling by moving struct sdebug_defer into the private SCSI command data instead of allocating it separately. The only functional change is that aborting a SCSI command now fails and is retried at a later time if the completion handler can't be cancelled. See also commit 1107c7b24ee3 ("scsi: scsi_debug: Dynamically allocate sdebug_queued_cmd"). Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20250224115517.495899-4-john.g.garry@oracle.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24scsi: scsi_debug: Remove a reference to in_use_bmBart Van Assche
Commit f1437cd1e535 ("scsi: scsi_debug: Drop sdebug_queue") removed the 'in_use_bm' struct member. Hence remove a reference to that struct member from the procfs host info file. Fixes: f1437cd1e535 ("scsi: scsi_debug: Drop sdebug_queue") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20250224115517.495899-3-john.g.garry@oracle.com Reviewed-by: John Garry <john.g.garry@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24scsi: scsi_debug: Remove sdebug_device_access_infoJohn Garry
This structure is not used, so delete it. It was originally intended for supporting checking for atomic writes overlapping with ongoing reads and writes, but that support never got added. SBC-4 r22 section 4.29.3.2 "Performing operations during an atomic write operation" describes two methods of handling overlapping atomic writes. Currently the only method supported is for the ongoing read or write to complete. Signed-off-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20250224115517.495899-2-john.g.garry@oracle.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-23scsi: scsi_debug: Add support for partitioning the tapeKai Mäkisara
This patch adds support for MEDIUM PARTITION PAGE in MODE SELECT and the FORMAT MEDIUM command for tapes. After these additions, the virtual tape can be partitioned containing either one or two partitions. The POFM flag in the mode page is set, meaning that the FORMAT MEDIUM command must be used to create the partitioning defined in the mode page. Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi> Link: https://lore.kernel.org/r/20250213092636.2510-8-Kai.Makisara@kolumbus.fi Reviewed-by: John Meneghini <jmeneghi@redhat.com> Tested-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-23scsi: scsi_debug: Reset tape setting at device resetKai Mäkisara
Set tape block size, density and compression to default values when the device is reset (either directly or via target, bus or host reset). Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi> Link: https://lore.kernel.org/r/20250213092636.2510-7-Kai.Makisara@kolumbus.fi Reviewed-by: John Meneghini <jmeneghi@redhat.com> Tested-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-23scsi: scsi_debug: Add compression mode page for tapesKai Mäkisara
Add support for compression mode page. The compression status is saved and returned. No UA is generated. Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi> Link: https://lore.kernel.org/r/20250213092636.2510-6-Kai.Makisara@kolumbus.fi Reviewed-by: John Meneghini <jmeneghi@redhat.com> Tested-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-23scsi: scsi_debug: Add read support and update locate for tapesKai Mäkisara
Support for the READ (6) and SPACE (6) commands for tapes based on the previous write patch is added. The LOCATE (10) command is updated to use the written data. Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi> Link: https://lore.kernel.org/r/20250213092636.2510-5-Kai.Makisara@kolumbus.fi Reviewed-by: John Meneghini <jmeneghi@redhat.com> Tested-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-23scsi: scsi_debug: Add write support with block lengths and 4 bytes of dataKai Mäkisara
The tape is implemented as fixed number (10 000) of 8-byte units. The first four bytes of a unit contains the type of the unit (data block, filemark or end-of-data mark). If the units is a data block, the first four bytes contain the block length and the remaining four bytes the first bytes of written data. This allows the user to use tags to see that the read block is what it was supposed to be. The tape can contain two partitions. Initially it is formatted as one partition consisting of all 10 000 units. This patch adds the WRITE(6) command for tapes and the WRITE FILEMARKS (6) command. The REWIND command is updated. Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi> Link: https://lore.kernel.org/r/20250213092636.2510-4-Kai.Makisara@kolumbus.fi Reviewed-by: John Meneghini <jmeneghi@redhat.com> Tested-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-23scsi: scsi_debug: Add READ BLOCK LIMITS and modify LOAD for tapesKai Mäkisara
The changes: - Add READ BLOCK LIMITS (512 - 1048576 bytes) - Make LOAD send New Media UA (not correct by the standard, but makes possible to test also this UA) Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi> Link: https://lore.kernel.org/r/20250213092636.2510-3-Kai.Makisara@kolumbus.fi Reviewed-by: John Meneghini <jmeneghi@redhat.com> Tested-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-23scsi: scsi_debug: First fixes for tapesKai Mäkisara
Patch includes the following: - Enable MODE SENSE/SELECT without actual page (to read/write only the Block Descriptor) - Store the density code and block size in the Block Descriptor (only short version for tapes) - Fix REWIND not to use the wrong page filling function Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi> Link: https://lore.kernel.org/r/20250213092636.2510-2-Kai.Makisara@kolumbus.fi Reviewed-by: John Meneghini <jmeneghi@redhat.com> Tested-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-18scsi: Switch to use hrtimer_setup()Nam Cao
hrtimer_setup() takes the callback function pointer as argument and initializes the timer completely. Replace hrtimer_init() and the open coded initialization of hrtimer::function with the new setup mechanism. Patch was created by using Coccinelle. Signed-off-by: Nam Cao <namcao@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Zack Rusin <zack.rusin@broadcom.com> Link: https://lore.kernel.org/all/c951a5966e134307b8e50afb08e4b742e3f6ad06.1738746904.git.namcao@linutronix.de
2025-01-10scsi: scsi_debug: Constify sdebug_driver_templateJohn Garry
It's better to have sdebug_driver_template as const, so update the probe path to set the shost members directly after allocation and make that change. Signed-off-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20250107153325.1689432-1-john.g.garry@oracle.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-01-10Merge branch '6.13/scsi-fixes' into 6.14/scsi-stagingMartin K. Petersen
Pull in fixes branch to resolve merge conflict in ufs-qcom.c. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-01-02scsi: scsi_debug: Skip host/bus reset settle delayBart Van Assche
Skip the reset settle delay during error handling since the scsi_debug driver doesn't need this delay. Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20241216184852.2626339-1-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-12-04scsi: Convert SCSI drivers to .sdev_configure()Bart Van Assche
The only difference between the .sdev_configure() and .slave_configure() methods is that the former accepts an additional 'limits' argument. Convert all SCSI drivers that define a .slave_configure() method to .sdev_configure(). This patch prepares for removing the .slave_configure() method. No functionality has been changed. Acked-by: Geoff Levand <geoff@infradead.org> # for ps3rom Acked-by: Khalid Aziz <khalid@gonehiking.org> # for the BusLogic driver Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20241022180839.2712439-4-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-12-04scsi: Rename .slave_alloc() and .slave_destroy()Bart Van Assche
Rename .slave_alloc() into .sdev_init() and .slave_destroy() into .sdev_destroy(). The new names make it clear that these are actions on SCSI devices. Make this change in the SCSI core, SCSI drivers and also in the ATA drivers. No functionality has been changed. This patch has been created as follows: * Change the text "slave_alloc" into "sdev_init" in all source files except those in drivers/net/ and Documentation/. * Change the text "slave_destroy" into "sdev_destroy" in all source files except those in drivers/net/ and Documentation/. * Rename lpfc_no_slave() into lpfc_no_sdev(). * Manually adjust whitespace where necessary to restore vertical alignment (dc395x driver and include/linux/libata.h). Acked-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20241022180839.2712439-2-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-12-04scsi: scsi_debug: Fix hrtimer support for ndelayJohn Garry
Since commit 771f712ba5b0 ("scsi: scsi_debug: Fix cmd duration calculation"), ns_from_boot value is only evaluated in schedule_resp() for polled requests. However, ns_from_boot is also required for hrtimer support for when ndelay is less than INCLUSIVE_TIMING_MAX_NS, so fix up the logic to decide when to evaluate ns_from_boot. Fixes: 771f712ba5b0 ("scsi: scsi_debug: Fix cmd duration calculation") Signed-off-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20241202130045.2335194-1-john.g.garry@oracle.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-30Merge tag 'scsi-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "Two small fixes, both in drivers (ufs and scsi_debug)" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: ufs: core: Fix another deadlock during RTC update scsi: scsi_debug: Fix do_device_access() handling of unexpected SG copy length
2024-10-25scsi: scsi_debug: Fix do_device_access() handling of unexpected SG copy lengthJohn Garry
If the sg_copy_buffer() call returns less than sdebug_sector_size, then we drop out of the copy loop. However, we still report that we copied the full expected amount, which is not proper. Fix by keeping a running total and return that value. Fixes: 84f3a3c01d70 ("scsi: scsi_debug: Atomic write support") Reported-by: Colin Ian King <colin.i.king@gmail.com> Suggested-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20241018101655.4207-1-john.g.garry@oracle.com Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-10-02move asm/unaligned.h to linux/unaligned.hAl Viro
asm/unaligned.h is always an include of asm-generic/unaligned.h; might as well move that thing to linux/unaligned.h and include that - there's nothing arch-specific in that header. auto-generated by the following: for i in `git grep -l -w asm/unaligned.h`; do sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i done for i in `git grep -l -w asm-generic/unaligned.h`; do sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i done git mv include/asm-generic/unaligned.h include/linux/unaligned.h git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
2024-09-12scsi: scsi_debug: Remove a useless memset()Christophe JAILLET
'arr' is kzalloc()'ed, so there is no need to call memset(.., 0, ...) on it. It is already cleared. This is a follow up of commit b952eb270df3 ("scsi: scsi_debug: Allocate the MODE SENSE response from the heap"). Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/6296722174e39a51cac74b7fc68b0d75bd0db2a3.1725690433.git.christophe.jaillet@wanadoo.fr Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-07-15Merge tag 'for-6.11/block-20240710' of git://git.kernel.dk/linuxLinus Torvalds
Pull block updates from Jens Axboe: - NVMe updates via Keith: - Device initialization memory leak fixes (Keith) - More constants defined (Weiwen) - Target debugfs support (Hannes) - PCIe subsystem reset enhancements (Keith) - Queue-depth multipath policy (Redhat and PureStorage) - Implement get_unique_id (Christoph) - Authentication error fixes (Gaosheng) - MD updates via Song - sync_action fix and refactoring (Yu Kuai) - Various small fixes (Christoph Hellwig, Li Nan, and Ofir Gal, Yu Kuai, Benjamin Marzinski, Christophe JAILLET, Yang Li) - Fix loop detach/open race (Gulam) - Fix lower control limit for blk-throttle (Yu) - Add module descriptions to various drivers (Jeff) - Add support for atomic writes for block devices, and statx reporting for same. Includes SCSI and NVMe (John, Prasad, Alan) - Add IO priority information to block trace points (Dongliang) - Various zone improvements and tweaks (Damien) - mq-deadline tag reservation improvements (Bart) - Ignore direct reclaim swap writes in writeback throttling (Baokun) - Block integrity improvements and fixes (Anuj) - Add basic support for rust based block drivers. Has a dummy null_blk variant for now (Andreas) - Series converting driver settings to queue limits, and cleanups and fixes related to that (Christoph) - Cleanup for poking too deeply into the bvec internals, in preparation for DMA mapping API changes (Christoph) - Various minor tweaks and fixes (Jiapeng, John, Kanchan, Mikulas, Ming, Zhu, Damien, Christophe, Chaitanya) * tag 'for-6.11/block-20240710' of git://git.kernel.dk/linux: (206 commits) floppy: add missing MODULE_DESCRIPTION() macro loop: add missing MODULE_DESCRIPTION() macro ublk_drv: add missing MODULE_DESCRIPTION() macro xen/blkback: add missing MODULE_DESCRIPTION() macro block/rnbd: Constify struct kobj_type block: take offset into account in blk_bvec_map_sg again block: fix get_max_segment_size() warning loop: Don't bother validating blocksize virtio_blk: Don't bother validating blocksize null_blk: Don't bother validating blocksize block: Validate logical block size in blk_validate_limits() virtio_blk: Fix default logical block size fallback nvmet-auth: fix nvmet_auth hash error handling nvme: implement ->get_unique_id block: pass a phys_addr_t to get_max_segment_size block: add a bvec_phys helper blk-lib: check for kill signal in ioctl BLKZEROOUT block: limit the Write Zeroes to manually writing zeroes fallback block: refacto blkdev_issue_zeroout block: move read-only and supported checks into (__)blkdev_issue_zeroout ...
2024-06-25scsi: scsi_debug: Fix create target debugfs failureMing Lei
Target debugfs entry is removed via async_schedule() which isn't drained when adding same name target, so failure of "Directory 'target11:0:0' with parent 'scsi_debug' already present!" can be triggered easily. Fix it by switching to domain async schedule, and draining it before adding new target debugfs entry. Cc: Wenchao Hao <haowenchao2@huawei.com> Fixes: f084fe52c640 ("scsi: scsi_debug: Add debugfs interface to fail target reset") Signed-off-by: Ming Lei <ming.lei@redhat.com> Acked-by: Wenchao Hao <haowenchao22@gmail.com> Link: https://lore.kernel.org/r/20240619013803.3008857-1-ming.lei@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-06-20scsi: scsi_debug: Atomic write supportJohn Garry
Add initial support for atomic writes. As is standard method, feed device properties via modules param, those being: - atomic_max_size_blks - atomic_alignment_blks - atomic_granularity_blks - atomic_max_size_with_boundary_blks - atomic_max_boundary_blks These just match sbc4r22 section 6.6.4 - Block limits VPD page. We just support ATOMIC WRITE (16). The major change in the driver is how we lock the device for RW accesses. Currently the driver uses a per-device lock for accessing device metadata and "media" data (calls to do_device_access()) atomically for the duration of the whole read/write command. This should not suit verifying atomic writes. Reason being that currently all reads/writes are atomic, so using atomic writes does not prove anything. Change device access model to basis that regular writes only atomic on a per-sector basis, while reads and atomic writes are fully atomic. As mentioned, since accessing metadata and device media is atomic, continue to have regular writes involving metadata - like discard or PI - as atomic. We can improve this later. Currently we only support model where overlapping going reads or writes wait for current access to complete before commencing an atomic write. This is described in 4.29.3.2 section of the SBC. However, we simplify, things and wait for all accesses to complete (when issuing an atomic write). Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: John Garry <john.g.garry@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Luis Chamberlain <mcgrof@kernel.org> Link: https://lore.kernel.org/r/20240620125359.2684798-10-john.g.garry@oracle.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
2024-03-22Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds
Pull more SCSI updates from James Bottomley: "The vfs has long had a write lifetime hint mechanism that gives the expected longevity on storage of the data being written. f2fs was the original consumer of this and used the hint for flash data placement (mostly to avoid write amplification by placing objects with similar lifetimes in the same erase block). More recently the SCSI based UFS (Universal Flash Storage) drivers have wanted to take advantage of this as well, for the same reasons as f2fs, necessitating plumbing the write hints through the block layer and then adding it to the SCSI core. The vfs write_hints already taken plumbs this as far as block and this completes the SCSI core enabling based on a recently agreed reuse of the old write command group number. The additions to the scsi_debug driver are for emulating this property so we can run tests on it in the absence of an actual UFS device" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: scsi_debug: Maintain write statistics per group number scsi: scsi_debug: Implement GET STREAM STATUS scsi: scsi_debug: Implement the IO Advice Hints Grouping mode page scsi: scsi_debug: Allocate the MODE SENSE response from the heap scsi: scsi_debug: Rework subpage code error handling scsi: scsi_debug: Rework page code error handling scsi: scsi_debug: Support the block limits extension VPD page scsi: scsi_debug: Reduce code duplication scsi: sd: Translate data lifetime information scsi: scsi_proto: Add structures and constants related to I/O groups and streams scsi: core: Query the Block Limits Extension VPD page
2024-02-26scsi: scsi_debug: Maintain write statistics per group numberBart Van Assche
Track per GROUP NUMBER how many write commands have been processed. Make this information available in sysfs. Reset these statistics if any data is written into the sysfs attribute. Note: SCSI devices should only interpret the information in the GROUP NUMBER field as a stream identifier if the ST_ENBLE bit has been set to one. This patch follows a simpler approach: count the number of writes per GROUP NUMBER whether or not the group number represents a stream identifier. Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240130214911.1863909-20-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-02-26scsi: scsi_debug: Implement GET STREAM STATUSBart Van Assche
Implement the GET STREAM STATUS SCSI command. Report that the first five stream indexes correspond to permanent streams. Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240130214911.1863909-19-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-02-26scsi: scsi_debug: Implement the IO Advice Hints Grouping mode pageBart Van Assche
Implement an IO Advice Hints Grouping mode page with three permanent streams. A permanent stream is a stream for which the device server does not allow closing or otherwise modifying the configuration of that stream. The stream identifier enable (ST_ENBLE) bit specifies whether the stream identifier may be used in the GROUP NUMBER field of SCSI WRITE commands. Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240130214911.1863909-18-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-02-26scsi: scsi_debug: Allocate the MODE SENSE response from the heapBart Van Assche
Make the MODE SENSE response buffer larger and allocate it from the heap. This patch prepares for adding support for the IO Advice Hints Grouping mode page. Suggested-by: Douglas Gilbert <dgilbert@interlog.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240130214911.1863909-17-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-02-26scsi: scsi_debug: Rework subpage code error handlingBart Van Assche
Move the subpage code checks into the switch statement to make it easier to add support for new page code / subpage code combinations. Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240130214911.1863909-16-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-02-26scsi: scsi_debug: Rework page code error handlingBart Van Assche
Instead of tracking whether or not the page code is valid in a boolean variable, jump to error handling code if an unsupported page code is encountered. Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240130214911.1863909-15-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-02-26scsi: scsi_debug: Support the block limits extension VPD pageBart Van Assche
>From SBC-5 r05: "Reduced stream control: a) reduces the maximum number of streams that the device server supports; and b) increases the number of write commands that are able to specify a stream to be written in any write command that contains the GROUP NUMBER field in its CDB. If the RSCS bit (see 6.6.5) is set to one, then the device server shall: a) support per group stream identifier usage as described in 4.32.2; b) support the IO Advice Hints Grouping mode page (see 6.5.7); and c) set the MAXIMUM NUMBER OF STREAMS field (see 6.6.5) to a value that is less than 64. Device servers that set the RSCS bit to one may support other features (e.g., permanent streams (see 4.32.4)). 4.32.4 Permanent streams A permanent stream is a stream for which the device server does not allow closing or otherwise modifying the configuration of that stream. The PERM bit (see 5.9.2.3) indicates whether a stream is a permanent stream. If a STREAM CONTROL command (see 5.32) specifies the closing of a permanent stream, the device server terminates that command with CHECK CONDITION status instead of closing the specified stream. A permanent stream is always an open stream. Device severs should assign the lowest numbered stream identifiers to permanent streams." Report that reduced stream control is supported. Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240130214911.1863909-14-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-02-26scsi: scsi_debug: Reduce code duplicationBart Van Assche
All VPD pages have the page code in byte one. Reduce code duplication by storing the VPD page code once. Reviewed-by: Avri Altman <avri.altman@wdc.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20240130214911.1863909-13-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-02-05scsi: scsi_debug: Make pseudo_lld_bus constRicardo B. Marliere
Now that the driver core can properly handle constant struct bus_type, move the pseudo_lld_bus variable to be a constant structure as well, placing it into read-only memory which can not be modified at runtime. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net> Link: https://lore.kernel.org/r/20240203-bus_cleanup-scsi-v1-3-6f552fb24f71@marliere.net Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-12-19block: remove support for the host aware zone modelChristoph Hellwig
When zones were first added the SCSI and ATA specs, two different models were supported (in addition to the drive managed one that is invisible to the host): - host managed where non-conventional zones there is strict requirement to write at the write pointer, or else an error is returned - host aware where a write point is maintained if writes always happen at it, otherwise it is left in an under-defined state and the sequential write preferred zones behave like conventional zones (probably very badly performing ones, though) Not surprisingly this lukewarm model didn't prove to be very useful and was finally removed from the ZBC and SBC specs (NVMe never implemented it). Due to to the easily disappearing write pointer host software could never rely on the write pointer to actually be useful for say recovery. Fortunately only a few HDD prototypes shipped using this model which never made it to mass production. Drop the support before it is too late. Note that any such host aware prototype HDD can still be used with Linux as we'll now treat it as a conventional HDD. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Link: https://lore.kernel.org/r/20231217165359.604246-4-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk>
2023-11-08scsi: scsi_debug: Delete some bogus error checkingDan Carpenter
Smatch complains that "dentry" is never initialized. These days everyone initializes all their stack variables to zero so this means that it will trigger a warning every time this function is run. Really, debugfs functions are not supposed to be checked for errors in normal code. For example, if we updated this code to check the correct variable then it would print a warning if CONFIG_DEBUGFS was disabled. We don't want that. Just delete the check. Fixes: f084fe52c640 ("scsi: scsi_debug: Add debugfs interface to fail target reset") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/c602c9ad-5e35-4e18-a47f-87ed956a9ec2@moroto.mountain Reviewed-by: Wenchao Hao <haowenchao2@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-11-08scsi: scsi_debug: Fix some bugs in sdebug_error_write()Dan Carpenter
There are two bug in this code: 1) If count is zero, then it will lead to a NULL dereference. The kmalloc() will successfully allocate zero bytes and the test for "if (buf[0] == '-')" will read beyond the end of the zero size buffer and Oops. 2) The code does not ensure that the user's string is properly NUL terminated which could lead to a read overflow. Fixes: a9996d722b11 ("scsi: scsi_debug: Add interface to manage error injection for a single device") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/7733643d-e102-4581-8d29-769472011c97@moroto.mountain Reviewed-by: Wenchao Hao <haowenchao2@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-10-16scsi: scsi_debug: Add param to control sdev's allow_restartWenchao Hao
Add new module param "allow_restart" to control scsi_device's allow_restart flag. This flag determines if EH is triggered after a command completes with sense_key 0x6, ASC 0x4 and ASCQ 0x2. EH would be triggered if allow_restart=1 in this condition. The new param can be used with the error injection capability to test how commands completing with sense_key 0x6, ASC 0x4 and ASCQ 0x2 are handled. Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Link: https://lore.kernel.org/r/20231010092051.608007-11-haowenchao2@huawei.com Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-10-16scsi: scsi_debug: Add debugfs interface to fail target resetWenchao Hao
The interface is found at /sys/kernel/debug/scsi_debug/target<h:c:t>/fail_reset where <h:c:t> identifies the target to inject errors on. It's a simple bool type interface which would make this target's reset fail if set to 'Y'. Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Link: https://lore.kernel.org/r/20231010092051.608007-10-haowenchao2@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-10-16scsi: scsi_debug: Add new error injection type: Reset LUN failedWenchao Hao
Add error injection type 4 to make scsi_debug_device_reset() return FAILED. Fail abort command format: +--------+------+-------------------------------------------------------+ | Column | Type | Description | +--------+------+-------------------------------------------------------+ | 1 | u8 | Error type, fixed to 0x4 | +--------+------+-------------------------------------------------------+ | 2 | s32 | Error count | | | | 0: this rule will be ignored | | | | positive: the rule will always take effect | | | | negative: the rule takes effect n times where -n is | | | | the value given. Ignored after n times | +--------+------+-------------------------------------------------------+ | 3 | x8 | SCSI command opcode, 0xff for all commands | +--------+------+-------------------------------------------------------+ Examples: error=/sys/kernel/debug/scsi_debug/0:0:0:1/error echo "4 -10 0x12" > ${error} will make the device return FAILED when trying to reset LUN with inquiry command 10 times. error=/sys/kernel/debug/scsi_debug/0:0:0:1/error echo "4 -10 0xff" > ${error} will make the device return FAILED when trying to reset LUN 10 times. Usually we do not care about what command it is when trying to perform reset LUN, so 0xff could be applied. Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Link: https://lore.kernel.org/r/20231010092051.608007-9-haowenchao2@huawei.com Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-10-16scsi: scsi_debug: Add new error injection type: Abort FailedWenchao Hao
Add error injection type 3 to make scsi_debug_abort() return FAILED. Fail abort command format: +--------+------+-------------------------------------------------------+ | Column | Type | Description | +--------+------+-------------------------------------------------------+ | 1 | u8 | Error type, fixed to 0x3 | +--------+------+-------------------------------------------------------+ | 2 | s32 | Error count | | | | 0: this rule will be ignored | | | | positive: the rule will always take effect | | | | negative: the rule takes effect n times where -n is | | | | the value given. Ignored after n times | +--------+------+-------------------------------------------------------+ | 3 | x8 | SCSI command opcode, 0xff for all commands | +--------+------+-------------------------------------------------------+ Examples: error=/sys/kernel/debug/scsi_debug/0:0:0:1/error echo "3 -10 0x12" > ${error} will make the device return FAILED when aborting inquiry command 10 times. Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Link: https://lore.kernel.org/r/20231010092051.608007-8-haowenchao2@huawei.com Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-10-16scsi: scsi_debug: Set command result and sense data if error is injectedWenchao Hao
If a fail command error is injected, set the command's status and sense data then finish this SCSI command. Set SCSI command's status and sense data format: +--------+------+-------------------------------------------------------+ | Column | Type | Description | +--------+------+-------------------------------------------------------+ | 1 | u8 | Error type, fixed to 0x2 | +--------+------+-------------------------------------------------------+ | 2 | s32 | Error Count | | | | 0: the rule will be ignored | | | | positive: the rule will always take effect | | | | negative: the rule takes effect n times where -n is | | | | the value given. Ignored after n times | +--------+------+-------------------------------------------------------+ | 3 | x8 | SCSI command opcode, 0xff for all commands | +--------+------+-------------------------------------------------------+ | 4 | x8 | Host byte in scsi_cmd::status | | | | [scsi_cmd::status has 32 bits holding these 3 bytes] | +--------+------+-------------------------------------------------------+ | 5 | x8 | Driver byte in scsi_cmd::status | +--------+------+-------------------------------------------------------+ | 6 | x8 | SCSI Status byte in scsi_cmd::status | +--------+------+-------------------------------------------------------+ | 7 | x8 | SCSI Sense Key in scsi_cmnd | +--------+------+-------------------------------------------------------+ | 8 | x8 | SCSI ASC in scsi_cmnd | +--------+------+-------------------------------------------------------+ | 9 | x8 | SCSI ASCQ in scsi_cmnd | +--------+------+-------------------------------------------------------+ Examples: error=/sys/kernel/debug/scsi_debug/0:0:0:1/error echo "2 -10 0x88 0 0 0x2 0x3 0x11 0x0" >${error} will make device's read command return with media error with additional sense of "Unrecovered read error" (UNC): Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Link: https://lore.kernel.org/r/20231010092051.608007-7-haowenchao2@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-10-16scsi: scsi_debug: Return failed value if error is injectedWenchao Hao
If a fail queuecommand error is injected, return the failed value defined in the rule from queuecommand. Make queuecommand return format: +--------+------+-------------------------------------------------------+ | Column | Type | Description | +--------+------+-------------------------------------------------------+ | 1 | u8 | Error type, fixed to 0x1 | +--------+------+-------------------------------------------------------+ | 2 | s32 | Error count | | | | 0: this rule will be ignored | | | | positive: the rule will always take effect | | | | negative: the rule takes effect n times where -n is | | | | the value given. Ignored after n times | +--------+------+-------------------------------------------------------+ | 3 | x8 | SCSI command opcode, 0xff for all commands | +--------+------+-------------------------------------------------------+ | 4 | x32 | The queuecommand() return value we want | +--------+------+-------------------------------------------------------+ Examples: error=/sys/kernel/debug/scsi_debug/0:0:0:1/error echo "1 1 0x12 0x1055" > ${error} will make each INQUIRY command sent to that device return 0x1055 (SCSI_MLQUEUE_HOST_BUSY). Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Link: https://lore.kernel.org/r/20231010092051.608007-6-haowenchao2@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-10-16scsi: scsi_debug: Time out command if the error is injectedWenchao Hao
If a timeout error is injected, return 0 from scsi_debug_queuecommand to make the command time out. Time out SCSI command format: +--------+------+-------------------------------------------------------+ | Column | Type | Description | +--------+------+-------------------------------------------------------+ | 1 | u8 | Error type, fixed to 0x0 | +--------+------+-------------------------------------------------------+ | 2 | s32 | Error count | | | | 0: this rule will be ignored | | | | positive: the rule will always take effect | | | | negative: the rule takes effect n times where -n is | | | | the value given. Ignored after n times | +--------+------+-------------------------------------------------------+ | 3 | x8 | SCSI command opcode, 0xff for all commands | +--------+------+-------------------------------------------------------+ Examples: error=/sys/kernel/debug/scsi_debug/0:0:0:1/error echo "0 -10 0x12" > ${error} will make the device's inquiry command time out 10 times. echo "0 1 0x12" > ${error} will make the device's inquiry time out each time it is invoked on this device. Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Link: https://lore.kernel.org/r/20231010092051.608007-5-haowenchao2@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-10-16scsi: scsi_debug: Define grammar to remove added error injectionWenchao Hao
The grammar to remove error injection is a line with fixed 3 columns separated by spaces. First column is fixed to "-". It tells this is a removal operation. Second column is the error code to match. Third column is the scsi command to match. For example the following command would remove timeout injection of inquiry command: echo "- 0 0x12" > /sys/kernel/debug/scsi_debug/0:0:0:1/error Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Link: https://lore.kernel.org/r/20231010092051.608007-4-haowenchao2@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-10-16scsi: scsi_debug: Add interface to manage error injection for a single deviceWenchao Hao
This new facility uses the debugfs pseudo file system which is typically mounted under the /sys/kernel/debug directory and requires root permissions to access. The interface file is found at /sys/kernel/debug/scsi_debug/<h:c:t:l>/error where <h:c:t:l> identifies the device (logical unit (LU)) to inject errors on. For the following description the ${error} environment variable is assumed to be set to/sys/kernel/debug/scsi_debug/1:0:0:0/error where 1:0:0:0 is a pseudo device (LU) owned by the scsi_debug driver. Rules are written to ${error} in the normal sysfs fashion (e.g. 'echo "0 -2 0x12" > ${error}'). More than one rule can be active on a device at a time and inactive rules (i.e. those whose error count is 0) remain in the rule listing. The existing rules can be read with 'cat ${error}' with oneline output for each rule. The interface format is line-by-line, each line is an error injection rule. Each rule contains integers separated by spaces, the first three columns correspond to "Error code", "Error count" and "SCSI command", other columns depend on Error code. General rule format: +--------+------+-------------------------------------------------------+ | Column | Type | Description | +--------+------+-------------------------------------------------------+ | 1 | u8 | Error code | | | | 0: timeout SCSI command | | | | 1: fail queuecommand, make queuecommand return | | | | given value | | | | 2: fail command, finish command with SCSI status, | | | | sense key and ASC/ASCQ values | | | | 3: make abort commands for specific command fail | | | | 4: make reset lun for specific command fail | +--------+------+-------------------------------------------------------+ | 2 | s32 | Error count | | | | 0: this rule will be ignored | | | | positive: the rule will always take effect | | | | negative: the rule takes effect n times where -n is | | | | the value given. Ignored after n times | +--------+------+-------------------------------------------------------+ | 3 | x8 | SCSI command opcode, 0xff for all commands | +--------+------+-------------------------------------------------------+ | ... | xxx | Error type specific fields | +--------+------+-------------------------------------------------------+ Notes: - When multiple error inject rules are added for the same SCSI command, the one with smaller error code will take effect (and the others will be ignored). - If the same error (i.e. same Error code and SCSI command) is added, the older one will be overwritten.. - Currently, the basic types are (u8/u16/u32/u64/s8/s16/s32/s64) and the hexadecimal types (x8/x16/x32/x64). - Where a hexadecimal value is expected (e.g. Column 3: SCSI command opcode) the "0x" prefix is optional on the value (e.g. the INQUIRY opcode can be given as '0x12' or '12'). - When the Error count is negative, reading ${error} will show that value incrementing, stopping when it gets to 0. Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Link: https://lore.kernel.org/r/20231010092051.608007-3-haowenchao2@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2023-10-16scsi: scsi_debug: Create scsi_debug directory in the debugfs filesystemWenchao Hao
Create directory scsi_debug in the root of the debugfs filesystem. Prepare to add interface for manage error injection. Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Link: https://lore.kernel.org/r/20231010092051.608007-2-haowenchao2@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
generated by cgit (git 2.34.1) at 2025-05-10 02:00:05 +0000