Merge tag 'arm-fixes-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull SoC fixes from Arnd Bergmann:
 "A number of devicetree fixes came in for the rockchip platforms,
  correcting some of the address information, and reverting a change to
  the MMC controller configuration that caused regressions.

  Four drivers have one code change each, addressing minor build issues
  for the optee firmware driver, the litex SoC platform driver and two
  reset drivers.

  The riscv fixes as also simple, mainly turning off device nodes in the
  canaan dts files unless they are actually usable on a particular
  board.

  Finally, Drew takes over maintaining the THEAD RISC-V SoC platform"

* tag 'arm-fixes-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  drivers/soc/litex: drop obsolete dependency on COMPILE_TEST
  tee: optee: ffa: Fix missing-field-initializers warning
  arm64: dts: rockchip: Add sound-dai-cells for RK3368
  arm64: dts: rockchip: Fix the i2c address of es8316 on Cool Pi 4B
  reset: hisilicon: hi6220: add missing MODULE_DESCRIPTION() macro
  reset: gpio: Fix missing gpiolib dependency for GPIO reset controller
  MAINTAINERS: thead: update Maintainer
  arm64: dts: rockchip: fix PMIC interrupt pin on ROCK Pi E
  riscv: dts: starfive: Set EMMC vqmmc maximum voltage to 3.3V on JH7110 boards
  arm64: dts: rockchip: make poweroff(8) work on Radxa ROCK 5A
  Revert "arm64: dts: rockchip: remove redundant cd-gpios from rk3588 sdmmc nodes"
  ARM: dts: rockchip: rk3066a: add #sound-dai-cells to hdmi node
  arm64: dts: rockchip: Fix the value of `dlg,jack-det-rate` mismatch on rk3399-gru
  arm64: dts: rockchip: set correct pwm0 pinctrl on rk3588-tiger
  riscv: dts: canaan: Disable I/O devices unless used
  riscv: dts: canaan: Clean up serial aliases
  arm64: dts: rockchip: Rename LED related pinctrl nodes on rk3308-rock-pi-s
  arm64: dts: rockchip: Fix SD NAND and eMMC init on rk3308-rock-pi-s
  arm64: dts: rockchip: Fix rk3308 codec@ff560000 reset-names
  arm64: dts: rockchip: Fix the DCDC_REG2 minimum voltage on Quartz64 Model B

27 files changed, 105 insertions, 35 deletions

diff --git a/MAINTAINERS b/MAINTAINERS
index 3c4fdf74a3f9..cd2ca0c3158e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19315,7 +19315,7 @@ F:	drivers/perf/riscv_pmu_legacy.c
 F:	drivers/perf/riscv_pmu_sbi.c
 
 RISC-V THEAD SoC SUPPORT
-M:	Jisheng Zhang <jszhang@kernel.org>
+M:	Drew Fustini <drew@pdp7.com>
 M:	Guo Ren <guoren@kernel.org>
 M:	Fu Wei <wefu@redhat.com>
 L:	linux-riscv@lists.infradead.org
diff --git a/arch/arm/boot/dts/rockchip/rk3066a.dtsi b/arch/arm/boot/dts/rockchip/rk3066a.dtsi
index 30139f21de64..15cbd94d7ec0 100644
--- a/arch/arm/boot/dts/rockchip/rk3066a.dtsi
+++ b/arch/arm/boot/dts/rockchip/rk3066a.dtsi
@@ -128,6 +128,7 @@
 		pinctrl-0 = <&hdmii2c_xfer>, <&hdmi_hpd>;
 		power-domains = <&power RK3066_PD_VIO>;
 		rockchip,grf = <&grf>;
+		#sound-dai-cells = <0>;
 		status = "disabled";
 
 		ports {
diff --git a/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts
index b47fe02c33fb..079101cddd65 100644
--- a/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts
@@ -5,6 +5,8 @@
  */
 
 /dts-v1/;
+
+#include <dt-bindings/leds/common.h>
 #include "rk3308.dtsi"
 
 / {
@@ -24,17 +26,21 @@
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
-		pinctrl-0 = <&green_led_gio>, <&heartbeat_led_gpio>;
+		pinctrl-0 = <&green_led>, <&heartbeat_led>;
 
 		green-led {
+			color = <LED_COLOR_ID_GREEN>;
 			default-state = "on";
+			function = LED_FUNCTION_POWER;
 			gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
 			label = "rockpis:green:power";
 			linux,default-trigger = "default-on";
 		};
 
 		blue-led {
+			color = <LED_COLOR_ID_BLUE>;
 			default-state = "on";
+			function = LED_FUNCTION_HEARTBEAT;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
 			label = "rockpis:blue:user";
 			linux,default-trigger = "heartbeat";
@@ -126,10 +132,12 @@
 };
 
 &emmc {
-	bus-width = <4>;
 	cap-mmc-highspeed;
-	mmc-hs200-1_8v;
+	cap-sd-highspeed;
+	no-sdio;
 	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;
 	vmmc-supply = <&vcc_io>;
 	status = "okay";
 };
@@ -214,11 +222,11 @@
 	pinctrl-0 = <&rtc_32k>;
 
 	leds {
-		green_led_gio: green-led-gpio {
+		green_led: green-led {
 			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 
-		heartbeat_led_gpio: heartbeat-led-gpio {
+		heartbeat_led: heartbeat-led {
 			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
diff --git a/arch/arm64/boot/dts/rockchip/rk3308.dtsi b/arch/arm64/boot/dts/rockchip/rk3308.dtsi
index 962ea893999b..c00da150a22f 100644
--- a/arch/arm64/boot/dts/rockchip/rk3308.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3308.dtsi
@@ -811,7 +811,7 @@
 		clocks = <&cru SCLK_I2S2_8CH_TX_OUT>,
 			 <&cru SCLK_I2S2_8CH_RX_OUT>,
 			 <&cru PCLK_ACODEC>;
-		reset-names = "codec-reset";
+		reset-names = "codec";
 		resets = <&cru SRST_ACODEC_P>;
 		#sound-dai-cells = <0>;
 		status = "disabled";
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
index f09d60bbe6c4..a608a219543e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
@@ -241,8 +241,8 @@
 	rk805: pmic@18 {
 		compatible = "rockchip,rk805";
 		reg = <0x18>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		#clock-cells = <1>;
 		clock-output-names = "xin32k", "rk805-clkout2";
 		gpio-controller;
diff --git a/arch/arm64/boot/dts/rockchip/rk3368.dtsi b/arch/arm64/boot/dts/rockchip/rk3368.dtsi
index 734f87db4d11..73618df7a889 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3368.dtsi
@@ -793,6 +793,7 @@
 		dma-names = "tx";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spdif_tx>;
+		#sound-dai-cells = <0>;
 		status = "disabled";
 	};
 
@@ -804,6 +805,7 @@
 		clocks = <&cru SCLK_I2S_2CH>, <&cru HCLK_I2S_2CH>;
 		dmas = <&dmac_bus 6>, <&dmac_bus 7>;
 		dma-names = "tx", "rx";
+		#sound-dai-cells = <0>;
 		status = "disabled";
 	};
 
@@ -817,6 +819,7 @@
 		dma-names = "tx", "rx";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2s_8ch_bus>;
+		#sound-dai-cells = <0>;
 		status = "disabled";
 	};
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
index 789fd0dcc88b..3cd63d1e8f15 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
@@ -450,7 +450,7 @@ ap_i2c_audio: &i2c8 {
 			dlg,btn-cfg = <50>;
 			dlg,mic-det-thr = <500>;
 			dlg,jack-ins-deb = <20>;
-			dlg,jack-det-rate = "32ms_64ms";
+			dlg,jack-det-rate = "32_64";
 			dlg,jack-rem-deb = <1>;
 
 			dlg,a-d-btn-thr = <0xa>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-b.dts b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-b.dts
index 26322a358d91..b908ce006c26 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-b.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-b.dts
@@ -289,7 +289,7 @@
 				regulator-name = "vdd_gpu";
 				regulator-always-on;
 				regulator-boot-on;
-				regulator-min-microvolt = <900000>;
+				regulator-min-microvolt = <500000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-ramp-delay = <6001>;
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts b/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts
index 1a604429fb26..e74871491ef5 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts
@@ -444,6 +444,7 @@
 &sdmmc {
 	bus-width = <4>;
 	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	max-frequency = <150000000>;
 	no-sdio;
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-quartzpro64.dts b/arch/arm64/boot/dts/rockchip/rk3588-quartzpro64.dts
index b4f22d95ac0e..e80caa36f8e4 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-quartzpro64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-quartzpro64.dts
@@ -435,6 +435,7 @@
 &sdmmc {
 	bus-width = <4>;
 	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	max-frequency = <150000000>;
 	no-sdio;
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
index b8e15b76a8a6..2e7512676b7e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
@@ -383,6 +383,7 @@
 	bus-width = <4>;
 	cap-mmc-highspeed;
 	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	sd-uhs-sdr104;
 	vmmc-supply = <&vcc_3v3_s3>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-tiger.dtsi b/arch/arm64/boot/dts/rockchip/rk3588-tiger.dtsi
index aebe1fedd2d8..615094bb8ba3 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-tiger.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588-tiger.dtsi
@@ -344,6 +344,11 @@
 	};
 };
 
+&pwm0 {
+	pinctrl-0 = <&pwm0m1_pins>;
+	pinctrl-names = "default";
+};
+
 &saradc {
 	vref-supply = <&vcc_1v8_s0>;
 	status = "okay";
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-coolpi-4b.dts b/arch/arm64/boot/dts/rockchip/rk3588s-coolpi-4b.dts
index 3b2ec1d0c542..074c316a9a69 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-coolpi-4b.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-coolpi-4b.dts
@@ -288,9 +288,9 @@
 	pinctrl-0 = <&i2c7m0_xfer>;
 	status = "okay";
 
-	es8316: audio-codec@11 {
+	es8316: audio-codec@10 {
 		compatible = "everest,es8316";
-		reg = <0x11>;
+		reg = <0x10>;
 		assigned-clocks = <&cru I2S0_8CH_MCLKOUT>;
 		assigned-clock-rates = <12288000>;
 		clocks = <&cru I2S0_8CH_MCLKOUT>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts b/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
index 8e2a07612d17..3b9a349362db 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-rock-5a.dts
@@ -366,6 +366,7 @@
 	bus-width = <4>;
 	cap-mmc-highspeed;
 	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	max-frequency = <150000000>;
 	no-sdio;
@@ -393,6 +394,7 @@
 		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
 			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
 		spi-max-frequency = <1000000>;
+		system-power-controller;
 
 		vcc1-supply = <&vcc5v0_sys>;
 		vcc2-supply = <&vcc5v0_sys>;
diff --git a/arch/riscv/boot/dts/canaan/canaan_kd233.dts b/arch/riscv/boot/dts/canaan/canaan_kd233.dts
index 8df4cf3656f2..a7d753b6fdfd 100644
--- a/arch/riscv/boot/dts/canaan/canaan_kd233.dts
+++ b/arch/riscv/boot/dts/canaan/canaan_kd233.dts
@@ -15,6 +15,10 @@
 	model = "Kendryte KD233";
 	compatible = "canaan,kendryte-kd233", "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -46,7 +50,6 @@
 &fpioa {
 	pinctrl-0 = <&jtag_pinctrl>;
 	pinctrl-names = "default";
-	status = "okay";
 
 	jtag_pinctrl: jtag-pinmux {
 		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
@@ -118,6 +121,7 @@
 	#sound-dai-cells = <1>;
 	pinctrl-0 = <&i2s0_pinctrl>;
 	pinctrl-names = "default";
+	status = "okay";
 };
 
 &spi0 {
@@ -125,6 +129,7 @@
 	pinctrl-names = "default";
 	num-cs = <1>;
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 
 	panel@0 {
 		compatible = "canaan,kd233-tft", "ilitek,ili9341";
diff --git a/arch/riscv/boot/dts/canaan/k210.dtsi b/arch/riscv/boot/dts/canaan/k210.dtsi
index f87c5164d9cf..4f5d40fa1e77 100644
--- a/arch/riscv/boot/dts/canaan/k210.dtsi
+++ b/arch/riscv/boot/dts/canaan/k210.dtsi
@@ -16,13 +16,6 @@
 	#size-cells = <1>;
 	compatible = "canaan,kendryte-k210";
 
-	aliases {
-		serial0 = &uarths0;
-		serial1 = &uart1;
-		serial2 = &uart2;
-		serial3 = &uart3;
-	};
-
 	/*
 	 * The K210 has an sv39 MMU following the privileged specification v1.9.
 	 * Since this is a non-ratified draft specification, the kernel does not
@@ -137,6 +130,7 @@
 			reg = <0x38000000 0x1000>;
 			interrupts = <33>;
 			clocks = <&sysclk K210_CLK_CPU>;
+			status = "disabled";
 		};
 
 		gpio0: gpio-controller@38001000 {
@@ -152,6 +146,7 @@
 				     <62>, <63>, <64>, <65>;
 			gpio-controller;
 			ngpios = <32>;
+			status = "disabled";
 		};
 
 		dmac0: dma-controller@50000000 {
@@ -187,6 +182,7 @@
 					 <&sysclk K210_CLK_GPIO>;
 				clock-names = "bus", "db";
 				resets = <&sysrst K210_RST_GPIO>;
+				status = "disabled";
 
 				gpio1_0: gpio-port@0 {
 					#gpio-cells = <2>;
@@ -214,6 +210,7 @@
 				dsr-override;
 				cts-override;
 				ri-override;
+				status = "disabled";
 			};
 
 			uart2: serial@50220000 {
@@ -230,6 +227,7 @@
 				dsr-override;
 				cts-override;
 				ri-override;
+				status = "disabled";
 			};
 
 			uart3: serial@50230000 {
@@ -246,6 +244,7 @@
 				dsr-override;
 				cts-override;
 				ri-override;
+				status = "disabled";
 			};
 
 			spi2: spi@50240000 {
@@ -259,6 +258,7 @@
 					 <&sysclk K210_CLK_APB0>;
 				clock-names = "ssi_clk", "pclk";
 				resets = <&sysrst K210_RST_SPI2>;
+				status = "disabled";
 			};
 
 			i2s0: i2s@50250000 {
@@ -268,6 +268,7 @@
 				clocks = <&sysclk K210_CLK_I2S0>;
 				clock-names = "i2sclk";
 				resets = <&sysrst K210_RST_I2S0>;
+				status = "disabled";
 			};
 
 			i2s1: i2s@50260000 {
@@ -277,6 +278,7 @@
 				clocks = <&sysclk K210_CLK_I2S1>;
 				clock-names = "i2sclk";
 				resets = <&sysrst K210_RST_I2S1>;
+				status = "disabled";
 			};
 
 			i2s2: i2s@50270000 {
@@ -286,6 +288,7 @@
 				clocks = <&sysclk K210_CLK_I2S2>;
 				clock-names = "i2sclk";
 				resets = <&sysrst K210_RST_I2S2>;
+				status = "disabled";
 			};
 
 			i2c0: i2c@50280000 {
@@ -296,6 +299,7 @@
 					 <&sysclk K210_CLK_APB0>;
 				clock-names = "ref", "pclk";
 				resets = <&sysrst K210_RST_I2C0>;
+				status = "disabled";
 			};
 
 			i2c1: i2c@50290000 {
@@ -306,6 +310,7 @@
 					 <&sysclk K210_CLK_APB0>;
 				clock-names = "ref", "pclk";
 				resets = <&sysrst K210_RST_I2C1>;
+				status = "disabled";
 			};
 
 			i2c2: i2c@502a0000 {
@@ -316,6 +321,7 @@
 					 <&sysclk K210_CLK_APB0>;
 				clock-names = "ref", "pclk";
 				resets = <&sysrst K210_RST_I2C2>;
+				status = "disabled";
 			};
 
 			fpioa: pinmux@502b0000 {
@@ -464,6 +470,7 @@
 				reset-names = "spi";
 				num-cs = <4>;
 				reg-io-width = <4>;
+				status = "disabled";
 			};
 
 			spi1: spi@53000000 {
@@ -479,6 +486,7 @@
 				reset-names = "spi";
 				num-cs = <4>;
 				reg-io-width = <4>;
+				status = "disabled";
 			};
 
 			spi3: spi@54000000 {
@@ -495,6 +503,7 @@
 
 				num-cs = <4>;
 				reg-io-width = <4>;
+				status = "disabled";
 			};
 		};
 	};
diff --git a/arch/riscv/boot/dts/canaan/k210_generic.dts b/arch/riscv/boot/dts/canaan/k210_generic.dts
index 396c8ca4d24d..5734cc03753b 100644
--- a/arch/riscv/boot/dts/canaan/k210_generic.dts
+++ b/arch/riscv/boot/dts/canaan/k210_generic.dts
@@ -15,6 +15,10 @@
 	model = "Kendryte K210 generic";
 	compatible = "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -24,7 +28,6 @@
 &fpioa {
 	pinctrl-0 = <&jtag_pins>;
 	pinctrl-names = "default";
-	status = "okay";
 
 	jtag_pins: jtag-pinmux {
 		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
diff --git a/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts b/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts
index 6d25bf07481a..2ab376d609d2 100644
--- a/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts
+++ b/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts
@@ -17,6 +17,10 @@
 	compatible = "sipeed,maix-bit", "sipeed,maix-bitm",
 		     "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -58,7 +62,6 @@
 &fpioa {
 	pinctrl-names = "default";
 	pinctrl-0 = <&jtag_pinctrl>;
-	status = "okay";
 
 	jtag_pinctrl: jtag-pinmux {
 		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
@@ -156,6 +159,7 @@
 	#sound-dai-cells = <1>;
 	pinctrl-0 = <&i2s0_pinctrl>;
 	pinctrl-names = "default";
+	status = "okay";
 };
 
 &i2c1 {
@@ -170,6 +174,7 @@
 	pinctrl-names = "default";
 	num-cs = <1>;
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 
 	panel@0 {
 		compatible = "sitronix,st7789v";
@@ -199,6 +204,8 @@
 };
 
 &spi3 {
+	status = "okay";
+
 	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
diff --git a/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts b/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts
index f4f4d8d5e8b8..d98e20775c07 100644
--- a/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts
+++ b/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts
@@ -17,6 +17,10 @@
 	compatible = "sipeed,maix-dock-m1", "sipeed,maix-dock-m1w",
 		     "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -63,7 +67,6 @@
 &fpioa {
 	pinctrl-0 = <&jtag_pinctrl>;
 	pinctrl-names = "default";
-	status = "okay";
 
 	jtag_pinctrl: jtag-pinmux {
 		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
@@ -159,6 +162,7 @@
 	#sound-dai-cells = <1>;
 	pinctrl-0 = <&i2s0_pinctrl>;
 	pinctrl-names = "default";
+	status = "okay";
 };
 
 &i2c1 {
@@ -173,6 +177,7 @@
 	pinctrl-names = "default";
 	num-cs = <1>;
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 
 	panel@0 {
 		compatible = "sitronix,st7789v";
diff --git a/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts b/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts
index 0d86df47e1ed..79ecd549700a 100644
--- a/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts
+++ b/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts
@@ -16,6 +16,10 @@
 	model = "SiPeed MAIX GO";
 	compatible = "sipeed,maix-go", "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -69,7 +73,6 @@
 &fpioa {
 	pinctrl-0 = <&jtag_pinctrl>;
 	pinctrl-names = "default";
-	status = "okay";
 
 	jtag_pinctrl: jtag-pinmux {
 		pinmux = <K210_FPIOA(0, K210_PCF_JTAG_TCLK)>,
@@ -167,6 +170,7 @@
 	#sound-dai-cells = <1>;
 	pinctrl-0 = <&i2s0_pinctrl>;
 	pinctrl-names = "default";
+	status = "okay";
 };
 
 &i2c1 {
@@ -181,6 +185,7 @@
 	pinctrl-names = "default";
 	num-cs = <1>;
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 
 	panel@0 {
 		compatible = "sitronix,st7789v";
@@ -209,6 +214,8 @@
 };
 
 &spi3 {
+	status = "okay";
+
 	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
diff --git a/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts b/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts
index 5c05c498e2b8..019c03ae51f6 100644
--- a/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts
+++ b/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts
@@ -15,6 +15,10 @@
 	model = "SiPeed MAIXDUINO";
 	compatible = "sipeed,maixduino", "canaan,kendryte-k210";
 
+	aliases {
+		serial0 = &uarths0;
+	};
+
 	chosen {
 		bootargs = "earlycon console=ttySIF0";
 		stdout-path = "serial0:115200n8";
@@ -39,8 +43,6 @@
 };
 
 &fpioa {
-	status = "okay";
-
 	uarths_pinctrl: uarths-pinmux {
 		pinmux = <K210_FPIOA(4, K210_PCF_UARTHS_RX)>, /* Header "0" */
 			 <K210_FPIOA(5, K210_PCF_UARTHS_TX)>; /* Header "1" */
@@ -132,6 +134,7 @@
 	#sound-dai-cells = <1>;
 	pinctrl-0 = <&i2s0_pinctrl>;
 	pinctrl-names = "default";
+	status = "okay";
 };
 
 &i2c1 {
@@ -146,6 +149,7 @@
 	pinctrl-names = "default";
 	num-cs = <1>;
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
 
 	panel@0 {
 		compatible = "sitronix,st7789v";
@@ -174,6 +178,8 @@
 };
 
 &spi3 {
+	status = "okay";
+
 	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
index 8ff6ea64f048..68d16717db8c 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
@@ -244,7 +244,7 @@
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-name = "emmc_vdd";
 			};
 		};
diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
index 7112f5932609..6bb5d9e372e4 100644
--- a/drivers/reset/Kconfig
+++ b/drivers/reset/Kconfig
@@ -68,6 +68,7 @@ config RESET_BRCMSTB_RESCAL
 
 config RESET_GPIO
 	tristate "GPIO reset controller"
+	depends on GPIOLIB
 	help
 	  This enables a generic reset controller for resets attached via
 	  GPIOs.  Typically for OF platforms this driver expects "reset-gpios"
diff --git a/drivers/reset/hisilicon/hi6220_reset.c b/drivers/reset/hisilicon/hi6220_reset.c
index 5c3267acd2b1..65aa5ff5ed82 100644
--- a/drivers/reset/hisilicon/hi6220_reset.c
+++ b/drivers/reset/hisilicon/hi6220_reset.c
@@ -219,4 +219,5 @@ static int __init hi6220_reset_init(void)
 
 postcore_initcall(hi6220_reset_init);
 
+MODULE_DESCRIPTION("Hisilicon Hi6220 reset controller driver");
 MODULE_LICENSE("GPL v2");
diff --git a/drivers/soc/litex/Kconfig b/drivers/soc/litex/Kconfig
index e6ba3573a772..f3f869639588 100644
--- a/drivers/soc/litex/Kconfig
+++ b/drivers/soc/litex/Kconfig
@@ -7,7 +7,7 @@ config LITEX
 
 config LITEX_SOC_CONTROLLER
 	tristate "Enable LiteX SoC Controller driver"
-	depends on OF || COMPILE_TEST
+	depends on OF
 	depends on HAS_IOMEM
 	select LITEX
 	help
diff --git a/drivers/soc/litex/litex_soc_ctrl.c b/drivers/soc/litex/litex_soc_ctrl.c
index 10813299aa10..72c44119dd54 100644
--- a/drivers/soc/litex/litex_soc_ctrl.c
+++ b/drivers/soc/litex/litex_soc_ctrl.c
@@ -82,13 +82,11 @@ static int litex_reset_handler(struct notifier_block *this, unsigned long mode,
 	return NOTIFY_DONE;
 }
 
-#ifdef CONFIG_OF
 static const struct of_device_id litex_soc_ctrl_of_match[] = {
 	{.compatible = "litex,soc-controller"},
 	{},
 };
 MODULE_DEVICE_TABLE(of, litex_soc_ctrl_of_match);
-#endif /* CONFIG_OF */
 
 static int litex_soc_ctrl_probe(struct platform_device *pdev)
 {
@@ -130,7 +128,7 @@ static void litex_soc_ctrl_remove(struct platform_device *pdev)
 static struct platform_driver litex_soc_ctrl_driver = {
 	.driver = {
 		.name = "litex-soc-controller",
-		.of_match_table = of_match_ptr(litex_soc_ctrl_of_match)
+		.of_match_table = litex_soc_ctrl_of_match,
 	},
 	.probe = litex_soc_ctrl_probe,
 	.remove_new = litex_soc_ctrl_remove,
diff --git a/drivers/tee/optee/ffa_abi.c b/drivers/tee/optee/ffa_abi.c
index 3235e1c719e8..3e73efa51bba 100644
--- a/drivers/tee/optee/ffa_abi.c
+++ b/drivers/tee/optee/ffa_abi.c
@@ -660,7 +660,9 @@ static bool optee_ffa_api_is_compatbile(struct ffa_device *ffa_dev,
 					const struct ffa_ops *ops)
 {
 	const struct ffa_msg_ops *msg_ops = ops->msg_ops;
-	struct ffa_send_direct_data data = { OPTEE_FFA_GET_API_VERSION };
+	struct ffa_send_direct_data data = {
+		.data0 = OPTEE_FFA_GET_API_VERSION,
+	};
 	int rc;
 
 	msg_ops->mode_32bit_set(ffa_dev);
@@ -677,7 +679,9 @@ static bool optee_ffa_api_is_compatbile(struct ffa_device *ffa_dev,
 		return false;
 	}
 
-	data = (struct ffa_send_direct_data){ OPTEE_FFA_GET_OS_VERSION };
+	data = (struct ffa_send_direct_data){
+		.data0 = OPTEE_FFA_GET_OS_VERSION,
+	};
 	rc = msg_ops->sync_send_receive(ffa_dev, &data);
 	if (rc) {
 		pr_err("Unexpected error %d\n", rc);
@@ -698,7 +702,9 @@ static bool optee_ffa_exchange_caps(struct ffa_device *ffa_dev,
 				    unsigned int *rpc_param_count,
 				    unsigned int *max_notif_value)
 {
-	struct ffa_send_direct_data data = { OPTEE_FFA_EXCHANGE_CAPABILITIES };
+	struct ffa_send_direct_data data = {
+		.data0 = OPTEE_FFA_EXCHANGE_CAPABILITIES,
+	};
 	int rc;
 
 	rc = ops->msg_ops->sync_send_receive(ffa_dev, &data);