Merge branch 'qca8k-phylink'

Russell King says:

====================
net: dsa: qca8k: convert to phylink_pcs and mark as non-legacy

This series adds support into DSA for the mac_select_pcs method, and
converts qca8k to make use of this, eventually marking qca8k as non-
legacy.

Patch 1 adds DSA support for mac_select_pcs.
Patch 2 and patch 3 moves code around in qca8k to make patch 4 more
readable.
Patch 4 does a simple conversion to phylink_pcs.
Patch 5 moves the serdes configuration to phylink_pcs.
Patch 6 marks qca8k as non-legacy.

v2: fix dsa_phylink_mac_select_pcs() formatting and double-blank line
in patch 5
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

4 files changed, 429 insertions, 322 deletions

diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
index c09d1569e66b..04fa21e37dfa 100644
--- a/drivers/net/dsa/qca8k.c
+++ b/drivers/net/dsa/qca8k.c
@@ -1632,220 +1632,6 @@ qca8k_parse_port_config(struct qca8k_priv *priv)
 	return 0;
 }
 
-static int
-qca8k_setup(struct dsa_switch *ds)
-{
-	struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
-	int cpu_port, ret, i;
-	u32 mask;
-
-	cpu_port = qca8k_find_cpu_port(ds);
-	if (cpu_port < 0) {
-		dev_err(priv->dev, "No cpu port configured in both cpu port0 and port6");
-		return cpu_port;
-	}
-
-	/* Parse CPU port config to be later used in phy_link mac_config */
-	ret = qca8k_parse_port_config(priv);
-	if (ret)
-		return ret;
-
-	ret = qca8k_setup_mdio_bus(priv);
-	if (ret)
-		return ret;
-
-	ret = qca8k_setup_of_pws_reg(priv);
-	if (ret)
-		return ret;
-
-	ret = qca8k_setup_mac_pwr_sel(priv);
-	if (ret)
-		return ret;
-
-	/* Make sure MAC06 is disabled */
-	ret = regmap_clear_bits(priv->regmap, QCA8K_REG_PORT0_PAD_CTRL,
-				QCA8K_PORT0_PAD_MAC06_EXCHANGE_EN);
-	if (ret) {
-		dev_err(priv->dev, "failed disabling MAC06 exchange");
-		return ret;
-	}
-
-	/* Enable CPU Port */
-	ret = regmap_set_bits(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0,
-			      QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN);
-	if (ret) {
-		dev_err(priv->dev, "failed enabling CPU port");
-		return ret;
-	}
-
-	/* Enable MIB counters */
-	ret = qca8k_mib_init(priv);
-	if (ret)
-		dev_warn(priv->dev, "mib init failed");
-
-	/* Initial setup of all ports */
-	for (i = 0; i < QCA8K_NUM_PORTS; i++) {
-		/* Disable forwarding by default on all ports */
-		ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
-				QCA8K_PORT_LOOKUP_MEMBER, 0);
-		if (ret)
-			return ret;
-
-		/* Enable QCA header mode on all cpu ports */
-		if (dsa_is_cpu_port(ds, i)) {
-			ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(i),
-					  FIELD_PREP(QCA8K_PORT_HDR_CTRL_TX_MASK, QCA8K_PORT_HDR_CTRL_ALL) |
-					  FIELD_PREP(QCA8K_PORT_HDR_CTRL_RX_MASK, QCA8K_PORT_HDR_CTRL_ALL));
-			if (ret) {
-				dev_err(priv->dev, "failed enabling QCA header mode");
-				return ret;
-			}
-		}
-
-		/* Disable MAC by default on all user ports */
-		if (dsa_is_user_port(ds, i))
-			qca8k_port_set_status(priv, i, 0);
-	}
-
-	/* Forward all unknown frames to CPU port for Linux processing
-	 * Notice that in multi-cpu config only one port should be set
-	 * for igmp, unknown, multicast and broadcast packet
-	 */
-	ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1,
-			  FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_MASK, BIT(cpu_port)) |
-			  FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_BC_DP_MASK, BIT(cpu_port)) |
-			  FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_MC_DP_MASK, BIT(cpu_port)) |
-			  FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_UC_DP_MASK, BIT(cpu_port)));
-	if (ret)
-		return ret;
-
-	/* Setup connection between CPU port & user ports
-	 * Configure specific switch configuration for ports
-	 */
-	for (i = 0; i < QCA8K_NUM_PORTS; i++) {
-		/* CPU port gets connected to all user ports of the switch */
-		if (dsa_is_cpu_port(ds, i)) {
-			ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
-					QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds));
-			if (ret)
-				return ret;
-		}
-
-		/* Individual user ports get connected to CPU port only */
-		if (dsa_is_user_port(ds, i)) {
-			ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
-					QCA8K_PORT_LOOKUP_MEMBER,
-					BIT(cpu_port));
-			if (ret)
-				return ret;
-
-			/* Enable ARP Auto-learning by default */
-			ret = regmap_set_bits(priv->regmap, QCA8K_PORT_LOOKUP_CTRL(i),
-					      QCA8K_PORT_LOOKUP_LEARN);
-			if (ret)
-				return ret;
-
-			/* For port based vlans to work we need to set the
-			 * default egress vid
-			 */
-			ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i),
-					QCA8K_EGREES_VLAN_PORT_MASK(i),
-					QCA8K_EGREES_VLAN_PORT(i, QCA8K_PORT_VID_DEF));
-			if (ret)
-				return ret;
-
-			ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i),
-					  QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) |
-					  QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF));
-			if (ret)
-				return ret;
-		}
-
-		/* The port 5 of the qca8337 have some problem in flood condition. The
-		 * original legacy driver had some specific buffer and priority settings
-		 * for the different port suggested by the QCA switch team. Add this
-		 * missing settings to improve switch stability under load condition.
-		 * This problem is limited to qca8337 and other qca8k switch are not affected.
-		 */
-		if (priv->switch_id == QCA8K_ID_QCA8337) {
-			switch (i) {
-			/* The 2 CPU port and port 5 requires some different
-			 * priority than any other ports.
-			 */
-			case 0:
-			case 5:
-			case 6:
-				mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x4) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x4) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI4(0x6) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI5(0x8) |
-					QCA8K_PORT_HOL_CTRL0_EG_PORT(0x1e);
-				break;
-			default:
-				mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x6) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x8) |
-					QCA8K_PORT_HOL_CTRL0_EG_PORT(0x19);
-			}
-			qca8k_write(priv, QCA8K_REG_PORT_HOL_CTRL0(i), mask);
-
-			mask = QCA8K_PORT_HOL_CTRL1_ING(0x6) |
-			QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
-			QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
-			QCA8K_PORT_HOL_CTRL1_WRED_EN;
-			qca8k_rmw(priv, QCA8K_REG_PORT_HOL_CTRL1(i),
-				  QCA8K_PORT_HOL_CTRL1_ING_BUF_MASK |
-				  QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
-				  QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
-				  QCA8K_PORT_HOL_CTRL1_WRED_EN,
-				  mask);
-		}
-
-		/* Set initial MTU for every port.
-		 * We have only have a general MTU setting. So track
-		 * every port and set the max across all port.
-		 * Set per port MTU to 1500 as the MTU change function
-		 * will add the overhead and if its set to 1518 then it
-		 * will apply the overhead again and we will end up with
-		 * MTU of 1536 instead of 1518
-		 */
-		priv->port_mtu[i] = ETH_DATA_LEN;
-	}
-
-	/* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */
-	if (priv->switch_id == QCA8K_ID_QCA8327) {
-		mask = QCA8K_GLOBAL_FC_GOL_XON_THRES(288) |
-		       QCA8K_GLOBAL_FC_GOL_XOFF_THRES(496);
-		qca8k_rmw(priv, QCA8K_REG_GLOBAL_FC_THRESH,
-			  QCA8K_GLOBAL_FC_GOL_XON_THRES_MASK |
-			  QCA8K_GLOBAL_FC_GOL_XOFF_THRES_MASK,
-			  mask);
-	}
-
-	/* Setup our port MTUs to match power on defaults */
-	ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN);
-	if (ret)
-		dev_warn(priv->dev, "failed setting MTU settings");
-
-	/* Flush the FDB table */
-	qca8k_fdb_flush(priv);
-
-	/* We don't have interrupts for link changes, so we need to poll */
-	ds->pcs_poll = true;
-
-	/* Set min a max ageing value supported */
-	ds->ageing_time_min = 7000;
-	ds->ageing_time_max = 458745000;
-
-	/* Set max number of LAGs supported */
-	ds->num_lag_ids = QCA8K_NUM_LAGS;
-
-	return 0;
-}
-
 static void
 qca8k_mac_config_setup_internal_delay(struct qca8k_priv *priv, int cpu_port_index,
 				      u32 reg)
@@ -1887,13 +1673,41 @@ qca8k_mac_config_setup_internal_delay(struct qca8k_priv *priv, int cpu_port_inde
 			cpu_port_index == QCA8K_CPU_PORT0 ? 0 : 6);
 }
 
+static struct phylink_pcs *
+qca8k_phylink_mac_select_pcs(struct dsa_switch *ds, int port,
+			     phy_interface_t interface)
+{
+	struct qca8k_priv *priv = ds->priv;
+	struct phylink_pcs *pcs = NULL;
+
+	switch (interface) {
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_1000BASEX:
+		switch (port) {
+		case 0:
+			pcs = &priv->pcs_port_0.pcs;
+			break;
+
+		case 6:
+			pcs = &priv->pcs_port_6.pcs;
+			break;
+		}
+		break;
+
+	default:
+		break;
+	}
+
+	return pcs;
+}
+
 static void
 qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 			 const struct phylink_link_state *state)
 {
 	struct qca8k_priv *priv = ds->priv;
-	int cpu_port_index, ret;
-	u32 reg, val;
+	int cpu_port_index;
+	u32 reg;
 
 	switch (port) {
 	case 0: /* 1st CPU port */
@@ -1959,70 +1773,6 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 	case PHY_INTERFACE_MODE_1000BASEX:
 		/* Enable SGMII on the port */
 		qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
-
-		/* Enable/disable SerDes auto-negotiation as necessary */
-		ret = qca8k_read(priv, QCA8K_REG_PWS, &val);
-		if (ret)
-			return;
-		if (phylink_autoneg_inband(mode))
-			val &= ~QCA8K_PWS_SERDES_AEN_DIS;
-		else
-			val |= QCA8K_PWS_SERDES_AEN_DIS;
-		qca8k_write(priv, QCA8K_REG_PWS, val);
-
-		/* Configure the SGMII parameters */
-		ret = qca8k_read(priv, QCA8K_REG_SGMII_CTRL, &val);
-		if (ret)
-			return;
-
-		val |= QCA8K_SGMII_EN_SD;
-
-		if (priv->ports_config.sgmii_enable_pll)
-			val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX |
-			       QCA8K_SGMII_EN_TX;
-
-		if (dsa_is_cpu_port(ds, port)) {
-			/* CPU port, we're talking to the CPU MAC, be a PHY */
-			val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
-			val |= QCA8K_SGMII_MODE_CTRL_PHY;
-		} else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
-			val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
-			val |= QCA8K_SGMII_MODE_CTRL_MAC;
-		} else if (state->interface == PHY_INTERFACE_MODE_1000BASEX) {
-			val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
-			val |= QCA8K_SGMII_MODE_CTRL_BASEX;
-		}
-
-		qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val);
-
-		/* From original code is reported port instability as SGMII also
-		 * require delay set. Apply advised values here or take them from DT.
-		 */
-		if (state->interface == PHY_INTERFACE_MODE_SGMII)
-			qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg);
-
-		/* For qca8327/qca8328/qca8334/qca8338 sgmii is unique and
-		 * falling edge is set writing in the PORT0 PAD reg
-		 */
-		if (priv->switch_id == QCA8K_ID_QCA8327 ||
-		    priv->switch_id == QCA8K_ID_QCA8337)
-			reg = QCA8K_REG_PORT0_PAD_CTRL;
-
-		val = 0;
-
-		/* SGMII Clock phase configuration */
-		if (priv->ports_config.sgmii_rx_clk_falling_edge)
-			val |= QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE;
-
-		if (priv->ports_config.sgmii_tx_clk_falling_edge)
-			val |= QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE;
-
-		if (val)
-			ret = qca8k_rmw(priv, reg,
-					QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE |
-					QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE,
-					val);
-
 		break;
 	default:
 		dev_err(ds->dev, "xMII mode %s not supported for port %d\n",
@@ -2064,48 +1814,8 @@ static void qca8k_phylink_get_caps(struct dsa_switch *ds, int port,
 
 	config->mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
 		MAC_10 | MAC_100 | MAC_1000FD;
-}
 
-static int
-qca8k_phylink_mac_link_state(struct dsa_switch *ds, int port,
-			     struct phylink_link_state *state)
-{
-	struct qca8k_priv *priv = ds->priv;
-	u32 reg;
-	int ret;
-
-	ret = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port), &reg);
-	if (ret < 0)
-		return ret;
-
-	state->link = !!(reg & QCA8K_PORT_STATUS_LINK_UP);
-	state->an_complete = state->link;
-	state->an_enabled = !!(reg & QCA8K_PORT_STATUS_LINK_AUTO);
-	state->duplex = (reg & QCA8K_PORT_STATUS_DUPLEX) ? DUPLEX_FULL :
-							   DUPLEX_HALF;
-
-	switch (reg & QCA8K_PORT_STATUS_SPEED) {
-	case QCA8K_PORT_STATUS_SPEED_10:
-		state->speed = SPEED_10;
-		break;
-	case QCA8K_PORT_STATUS_SPEED_100:
-		state->speed = SPEED_100;
-		break;
-	case QCA8K_PORT_STATUS_SPEED_1000:
-		state->speed = SPEED_1000;
-		break;
-	default:
-		state->speed = SPEED_UNKNOWN;
-		break;
-	}
-
-	state->pause = MLO_PAUSE_NONE;
-	if (reg & QCA8K_PORT_STATUS_RXFLOW)
-		state->pause |= MLO_PAUSE_RX;
-	if (reg & QCA8K_PORT_STATUS_TXFLOW)
-		state->pause |= MLO_PAUSE_TX;
-
-	return 1;
+	config->legacy_pre_march2020 = false;
 }
 
 static void
@@ -2158,6 +1868,163 @@ qca8k_phylink_mac_link_up(struct dsa_switch *ds, int port, unsigned int mode,
 	qca8k_write(priv, QCA8K_REG_PORT_STATUS(port), reg);
 }
 
+static struct qca8k_pcs *pcs_to_qca8k_pcs(struct phylink_pcs *pcs)
+{
+	return container_of(pcs, struct qca8k_pcs, pcs);
+}
+
+static void qca8k_pcs_get_state(struct phylink_pcs *pcs,
+				struct phylink_link_state *state)
+{
+	struct qca8k_priv *priv = pcs_to_qca8k_pcs(pcs)->priv;
+	int port = pcs_to_qca8k_pcs(pcs)->port;
+	u32 reg;
+	int ret;
+
+	ret = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port), &reg);
+	if (ret < 0) {
+		state->link = false;
+		return;
+	}
+
+	state->link = !!(reg & QCA8K_PORT_STATUS_LINK_UP);
+	state->an_complete = state->link;
+	state->an_enabled = !!(reg & QCA8K_PORT_STATUS_LINK_AUTO);
+	state->duplex = (reg & QCA8K_PORT_STATUS_DUPLEX) ? DUPLEX_FULL :
+							   DUPLEX_HALF;
+
+	switch (reg & QCA8K_PORT_STATUS_SPEED) {
+	case QCA8K_PORT_STATUS_SPEED_10:
+		state->speed = SPEED_10;
+		break;
+	case QCA8K_PORT_STATUS_SPEED_100:
+		state->speed = SPEED_100;
+		break;
+	case QCA8K_PORT_STATUS_SPEED_1000:
+		state->speed = SPEED_1000;
+		break;
+	default:
+		state->speed = SPEED_UNKNOWN;
+		break;
+	}
+
+	if (reg & QCA8K_PORT_STATUS_RXFLOW)
+		state->pause |= MLO_PAUSE_RX;
+	if (reg & QCA8K_PORT_STATUS_TXFLOW)
+		state->pause |= MLO_PAUSE_TX;
+}
+
+static int qca8k_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
+			    phy_interface_t interface,
+			    const unsigned long *advertising,
+			    bool permit_pause_to_mac)
+{
+	struct qca8k_priv *priv = pcs_to_qca8k_pcs(pcs)->priv;
+	int cpu_port_index, ret, port;
+	u32 reg, val;
+
+	port = pcs_to_qca8k_pcs(pcs)->port;
+	switch (port) {
+	case 0:
+		reg = QCA8K_REG_PORT0_PAD_CTRL;
+		cpu_port_index = QCA8K_CPU_PORT0;
+		break;
+
+	case 6:
+		reg = QCA8K_REG_PORT6_PAD_CTRL;
+		cpu_port_index = QCA8K_CPU_PORT6;
+		break;
+
+	default:
+		WARN_ON(1);
+	}
+
+	/* Enable/disable SerDes auto-negotiation as necessary */
+	ret = qca8k_read(priv, QCA8K_REG_PWS, &val);
+	if (ret)
+		return ret;
+	if (phylink_autoneg_inband(mode))
+		val &= ~QCA8K_PWS_SERDES_AEN_DIS;
+	else
+		val |= QCA8K_PWS_SERDES_AEN_DIS;
+	qca8k_write(priv, QCA8K_REG_PWS, val);
+
+	/* Configure the SGMII parameters */
+	ret = qca8k_read(priv, QCA8K_REG_SGMII_CTRL, &val);
+	if (ret)
+		return ret;
+
+	val |= QCA8K_SGMII_EN_SD;
+
+	if (priv->ports_config.sgmii_enable_pll)
+		val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX |
+		       QCA8K_SGMII_EN_TX;
+
+	if (dsa_is_cpu_port(priv->ds, port)) {
+		/* CPU port, we're talking to the CPU MAC, be a PHY */
+		val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
+		val |= QCA8K_SGMII_MODE_CTRL_PHY;
+	} else if (interface == PHY_INTERFACE_MODE_SGMII) {
+		val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
+		val |= QCA8K_SGMII_MODE_CTRL_MAC;
+	} else if (interface == PHY_INTERFACE_MODE_1000BASEX) {
+		val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
+		val |= QCA8K_SGMII_MODE_CTRL_BASEX;
+	}
+
+	qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val);
+
+	/* From original code is reported port instability as SGMII also
+	 * require delay set. Apply advised values here or take them from DT.
+	 */
+	if (interface == PHY_INTERFACE_MODE_SGMII)
+		qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg);
+	/* For qca8327/qca8328/qca8334/qca8338 sgmii is unique and
+	 * falling edge is set writing in the PORT0 PAD reg
+	 */
+	if (priv->switch_id == QCA8K_ID_QCA8327 ||
+	    priv->switch_id == QCA8K_ID_QCA8337)
+		reg = QCA8K_REG_PORT0_PAD_CTRL;
+
+	val = 0;
+
+	/* SGMII Clock phase configuration */
+	if (priv->ports_config.sgmii_rx_clk_falling_edge)
+		val |= QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE;
+
+	if (priv->ports_config.sgmii_tx_clk_falling_edge)
+		val |= QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE;
+
+	if (val)
+		ret = qca8k_rmw(priv, reg,
+				QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE |
+				QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE,
+				val);
+
+	return 0;
+}
+
+static void qca8k_pcs_an_restart(struct phylink_pcs *pcs)
+{
+}
+
+static const struct phylink_pcs_ops qca8k_pcs_ops = {
+	.pcs_get_state = qca8k_pcs_get_state,
+	.pcs_config = qca8k_pcs_config,
+	.pcs_an_restart = qca8k_pcs_an_restart,
+};
+
+static void qca8k_setup_pcs(struct qca8k_priv *priv, struct qca8k_pcs *qpcs,
+			    int port)
+{
+	qpcs->pcs.ops = &qca8k_pcs_ops;
+
+	/* We don't have interrupts for link changes, so we need to poll */
+	qpcs->pcs.poll = true;
+	qpcs->priv = priv;
+	qpcs->port = port;
+}
+
 static void
 qca8k_get_strings(struct dsa_switch *ds, int port, u32 stringset, uint8_t *data)
 {
@@ -2990,6 +2857,220 @@ static int qca8k_connect_tag_protocol(struct dsa_switch *ds,
 	return 0;
 }
 
+static int
+qca8k_setup(struct dsa_switch *ds)
+{
+	struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
+	int cpu_port, ret, i;
+	u32 mask;
+
+	cpu_port = qca8k_find_cpu_port(ds);
+	if (cpu_port < 0) {
+		dev_err(priv->dev, "No cpu port configured in both cpu port0 and port6");
+		return cpu_port;
+	}
+
+	/* Parse CPU port config to be later used in phy_link mac_config */
+	ret = qca8k_parse_port_config(priv);
+	if (ret)
+		return ret;
+
+	ret = qca8k_setup_mdio_bus(priv);
+	if (ret)
+		return ret;
+
+	ret = qca8k_setup_of_pws_reg(priv);
+	if (ret)
+		return ret;
+
+	ret = qca8k_setup_mac_pwr_sel(priv);
+	if (ret)
+		return ret;
+
+	qca8k_setup_pcs(priv, &priv->pcs_port_0, 0);
+	qca8k_setup_pcs(priv, &priv->pcs_port_6, 6);
+
+	/* Make sure MAC06 is disabled */
+	ret = regmap_clear_bits(priv->regmap, QCA8K_REG_PORT0_PAD_CTRL,
+				QCA8K_PORT0_PAD_MAC06_EXCHANGE_EN);
+	if (ret) {
+		dev_err(priv->dev, "failed disabling MAC06 exchange");
+		return ret;
+	}
+
+	/* Enable CPU Port */
+	ret = regmap_set_bits(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0,
+			      QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN);
+	if (ret) {
+		dev_err(priv->dev, "failed enabling CPU port");
+		return ret;
+	}
+
+	/* Enable MIB counters */
+	ret = qca8k_mib_init(priv);
+	if (ret)
+		dev_warn(priv->dev, "mib init failed");
+
+	/* Initial setup of all ports */
+	for (i = 0; i < QCA8K_NUM_PORTS; i++) {
+		/* Disable forwarding by default on all ports */
+		ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
+				QCA8K_PORT_LOOKUP_MEMBER, 0);
+		if (ret)
+			return ret;
+
+		/* Enable QCA header mode on all cpu ports */
+		if (dsa_is_cpu_port(ds, i)) {
+			ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(i),
+					  FIELD_PREP(QCA8K_PORT_HDR_CTRL_TX_MASK, QCA8K_PORT_HDR_CTRL_ALL) |
+					  FIELD_PREP(QCA8K_PORT_HDR_CTRL_RX_MASK, QCA8K_PORT_HDR_CTRL_ALL));
+			if (ret) {
+				dev_err(priv->dev, "failed enabling QCA header mode");
+				return ret;
+			}
+		}
+
+		/* Disable MAC by default on all user ports */
+		if (dsa_is_user_port(ds, i))
+			qca8k_port_set_status(priv, i, 0);
+	}
+
+	/* Forward all unknown frames to CPU port for Linux processing
+	 * Notice that in multi-cpu config only one port should be set
+	 * for igmp, unknown, multicast and broadcast packet
+	 */
+	ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1,
+			  FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_MASK, BIT(cpu_port)) |
+			  FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_BC_DP_MASK, BIT(cpu_port)) |
+			  FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_MC_DP_MASK, BIT(cpu_port)) |
+			  FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_UC_DP_MASK, BIT(cpu_port)));
+	if (ret)
+		return ret;
+
+	/* Setup connection between CPU port & user ports
+	 * Configure specific switch configuration for ports
+	 */
+	for (i = 0; i < QCA8K_NUM_PORTS; i++) {
+		/* CPU port gets connected to all user ports of the switch */
+		if (dsa_is_cpu_port(ds, i)) {
+			ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
+					QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds));
+			if (ret)
+				return ret;
+		}
+
+		/* Individual user ports get connected to CPU port only */
+		if (dsa_is_user_port(ds, i)) {
+			ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
+					QCA8K_PORT_LOOKUP_MEMBER,
+					BIT(cpu_port));
+			if (ret)
+				return ret;
+
+			/* Enable ARP Auto-learning by default */
+			ret = regmap_set_bits(priv->regmap, QCA8K_PORT_LOOKUP_CTRL(i),
+					      QCA8K_PORT_LOOKUP_LEARN);
+			if (ret)
+				return ret;
+
+			/* For port based vlans to work we need to set the
+			 * default egress vid
+			 */
+			ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i),
+					QCA8K_EGREES_VLAN_PORT_MASK(i),
+					QCA8K_EGREES_VLAN_PORT(i, QCA8K_PORT_VID_DEF));
+			if (ret)
+				return ret;
+
+			ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i),
+					  QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) |
+					  QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF));
+			if (ret)
+				return ret;
+		}
+
+		/* The port 5 of the qca8337 have some problem in flood condition. The
+		 * original legacy driver had some specific buffer and priority settings
+		 * for the different port suggested by the QCA switch team. Add this
+		 * missing settings to improve switch stability under load condition.
+		 * This problem is limited to qca8337 and other qca8k switch are not affected.
+		 */
+		if (priv->switch_id == QCA8K_ID_QCA8337) {
+			switch (i) {
+			/* The 2 CPU port and port 5 requires some different
+			 * priority than any other ports.
+			 */
+			case 0:
+			case 5:
+			case 6:
+				mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
+					QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
+					QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x4) |
+					QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x4) |
+					QCA8K_PORT_HOL_CTRL0_EG_PRI4(0x6) |
+					QCA8K_PORT_HOL_CTRL0_EG_PRI5(0x8) |
+					QCA8K_PORT_HOL_CTRL0_EG_PORT(0x1e);
+				break;
+			default:
+				mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
+					QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
+					QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x6) |
+					QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x8) |
+					QCA8K_PORT_HOL_CTRL0_EG_PORT(0x19);
+			}
+			qca8k_write(priv, QCA8K_REG_PORT_HOL_CTRL0(i), mask);
+
+			mask = QCA8K_PORT_HOL_CTRL1_ING(0x6) |
+			QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
+			QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
+			QCA8K_PORT_HOL_CTRL1_WRED_EN;
+			qca8k_rmw(priv, QCA8K_REG_PORT_HOL_CTRL1(i),
+				  QCA8K_PORT_HOL_CTRL1_ING_BUF_MASK |
+				  QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
+				  QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
+				  QCA8K_PORT_HOL_CTRL1_WRED_EN,
+				  mask);
+		}
+
+		/* Set initial MTU for every port.
+		 * We have only have a general MTU setting. So track
+		 * every port and set the max across all port.
+		 * Set per port MTU to 1500 as the MTU change function
+		 * will add the overhead and if its set to 1518 then it
+		 * will apply the overhead again and we will end up with
+		 * MTU of 1536 instead of 1518
+		 */
+		priv->port_mtu[i] = ETH_DATA_LEN;
+	}
+
+	/* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */
+	if (priv->switch_id == QCA8K_ID_QCA8327) {
+		mask = QCA8K_GLOBAL_FC_GOL_XON_THRES(288) |
+		       QCA8K_GLOBAL_FC_GOL_XOFF_THRES(496);
+		qca8k_rmw(priv, QCA8K_REG_GLOBAL_FC_THRESH,
+			  QCA8K_GLOBAL_FC_GOL_XON_THRES_MASK |
+			  QCA8K_GLOBAL_FC_GOL_XOFF_THRES_MASK,
+			  mask);
+	}
+
+	/* Setup our port MTUs to match power on defaults */
+	ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN);
+	if (ret)
+		dev_warn(priv->dev, "failed setting MTU settings");
+
+	/* Flush the FDB table */
+	qca8k_fdb_flush(priv);
+
+	/* Set min a max ageing value supported */
+	ds->ageing_time_min = 7000;
+	ds->ageing_time_max = 458745000;
+
+	/* Set max number of LAGs supported */
+	ds->num_lag_ids = QCA8K_NUM_LAGS;
+
+	return 0;
+}
+
 static const struct dsa_switch_ops qca8k_switch_ops = {
 	.get_tag_protocol	= qca8k_get_tag_protocol,
 	.setup			= qca8k_setup,
@@ -3018,7 +3099,7 @@ static const struct dsa_switch_ops qca8k_switch_ops = {
 	.port_vlan_add		= qca8k_port_vlan_add,
 	.port_vlan_del		= qca8k_port_vlan_del,
 	.phylink_get_caps	= qca8k_phylink_get_caps,
-	.phylink_mac_link_state	= qca8k_phylink_mac_link_state,
+	.phylink_mac_select_pcs	= qca8k_phylink_mac_select_pcs,
 	.phylink_mac_config	= qca8k_phylink_mac_config,
 	.phylink_mac_link_down	= qca8k_phylink_mac_link_down,
 	.phylink_mac_link_up	= qca8k_phylink_mac_link_up,
diff --git a/drivers/net/dsa/qca8k.h b/drivers/net/dsa/qca8k.h
index c3d3c2269b1d..f375627174c8 100644
--- a/drivers/net/dsa/qca8k.h
+++ b/drivers/net/dsa/qca8k.h
@@ -376,6 +376,12 @@ struct qca8k_mdio_cache {
 	u16 hi;
 };
 
+struct qca8k_pcs {
+	struct phylink_pcs pcs;
+	struct qca8k_priv *priv;
+	int port;
+};
+
 struct qca8k_priv {
 	u8 switch_id;
 	u8 switch_revision;
@@ -397,6 +403,8 @@ struct qca8k_priv {
 	struct qca8k_mgmt_eth_data mgmt_eth_data;
 	struct qca8k_mib_eth_data mib_eth_data;
 	struct qca8k_mdio_cache mdio_cache;
+	struct qca8k_pcs pcs_port_0;
+	struct qca8k_pcs pcs_port_6;
 };
 
 struct qca8k_mib_desc {
diff --git a/include/net/dsa.h b/include/net/dsa.h
index c8626dec970c..bc6eef6af810 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -788,6 +788,9 @@ struct dsa_switch_ops {
 	void	(*phylink_validate)(struct dsa_switch *ds, int port,
 				    unsigned long *supported,
 				    struct phylink_link_state *state);
+	struct phylink_pcs *(*phylink_mac_select_pcs)(struct dsa_switch *ds,
+						      int port,
+						      phy_interface_t iface);
 	int	(*phylink_mac_link_state)(struct dsa_switch *ds, int port,
 					  struct phylink_link_state *state);
 	void	(*phylink_mac_config)(struct dsa_switch *ds, int port,
diff --git a/net/dsa/port.c b/net/dsa/port.c
index c731af0adf04..056c6f51ac20 100644
--- a/net/dsa/port.c
+++ b/net/dsa/port.c
@@ -1053,6 +1053,20 @@ static void dsa_port_phylink_mac_pcs_get_state(struct phylink_config *config,
 	}
 }
 
+static struct phylink_pcs *
+dsa_port_phylink_mac_select_pcs(struct phylink_config *config,
+				phy_interface_t interface)
+{
+	struct dsa_port *dp = container_of(config, struct dsa_port, pl_config);
+	struct dsa_switch *ds = dp->ds;
+	struct phylink_pcs *pcs = NULL;
+
+	if (ds->ops->phylink_mac_select_pcs)
+		pcs = ds->ops->phylink_mac_select_pcs(ds, dp->index, interface);
+
+	return pcs;
+}
+
 static void dsa_port_phylink_mac_config(struct phylink_config *config,
 					unsigned int mode,
 					const struct phylink_link_state *state)
@@ -1119,6 +1133,7 @@ static void dsa_port_phylink_mac_link_up(struct phylink_config *config,
 
 static const struct phylink_mac_ops dsa_port_phylink_mac_ops = {
 	.validate = dsa_port_phylink_validate,
+	.mac_select_pcs = dsa_port_phylink_mac_select_pcs,
 	.mac_pcs_get_state = dsa_port_phylink_mac_pcs_get_state,
 	.mac_config = dsa_port_phylink_mac_config,
 	.mac_an_restart = dsa_port_phylink_mac_an_restart,