| Age | Commit message (Collapse) | Author |
|---|
|
It is considered good practice to disable on-SoC devices providing
external I/O in the SoC-specific .dtsi, and enable them explicitly in
the board-specific DTS files when actually wired-up and used.
Hence:
- Set the status of I/O devices in k210.dtsi to "disabled",
- Override the status of used I/O devices in board-specific DTS files
to "okay",
- Drop unneeded status overrides in board DTS-specific files for the
always-enabled pin controller.
On e.g. MAiXBiT, this gets rid of an error message when probing the
unused slave-only spi2 controller:
dw_spi_mmio 50240000.spi: error -22: problem registering spi host
dw_spi_mmio 50240000.spi: probe with driver dw_spi_mmio failed with error -22
which is seen since commit 98d75b9ef282f6b9 ("spi: dw: Drop default
number of CS setting").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The SoC-specific k210.dtsi declares aliases for all four serial ports.
However, none of the board-specific DTS files configure pin control for
any but the first serial port, so the last three ports are not usable.
Move the aliases node from the SoC-specific k210.dtsi to the
board-specific DTS files, as these are really board-specific, and retain
the sole port that is usable.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The BUILTIN_DTB_SOURCE was only configured for K210 before. Since
SOC_BUILTIN_DTB_DECLARE was removed at commit d5805af9fe9f ("riscv: Fix
builtin DTB handling") from patch [1], the kernel cannot choose one of the
dtbs from then on and always take the first one dtb to use. Then, another
commit 0ddd7eaffa64 ("riscv: Fix BUILTIN_DTB for sifive and microchip soc")
from patch [2] supports BUILTIN_DTB_SOURCE for other SoCs. However, this
feature will only work if the Kconfig we use links the dtb we expected in
the first place as mentioned in the thread [3]. Thus, a config
BUILTIN_DTB_SOURCE is needed for all SoCs to choose one dtb to use.
For some considerations, this patch also removes default y if XIP_KERNEL
for BUILTIN_DTB, as this requires setting a proper dtb to use on the
BUILTIN_DTB_SOURCE, else the kernel with XIP but does not set
BUILTIN_DTB_SOURCE or unselect BUILTIN_DTB will not boot.
Also, this patch removes the default dtb string for k210 from Kconfig to
nommu_k210_defconfig and nommu_k210_sdcard_defconfig to avoid complex
Kconfig settings for other SoCs in the future.
[1] https://lore.kernel.org/linux-riscv/20201208073355.40828-5-damien.lemoal@wdc.com/
[2] https://lore.kernel.org/linux-riscv/20210604120639.1447869-1-alex@ghiti.fr/
[3] https://lore.kernel.org/linux-riscv/CAK7LNATt_56mO2Le4v4EnPnAfd3gC8S_Sm5-GCsfa=qXy=8Lrg@mail.gmail.com/
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The spi-max-frequency is a property of SPI children, not the
controller:
k210_generic.dtb: spi@50240000: Unevaluated properties are not allowed ('spi-max-frequency' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Convert all non user visible use of SOC_FOO symbols to their ARCH_FOO
variants. The canaan DTs are an outlier in that they're gated at the
directory and the file level. Drop the directory level gating while we
are swapping the symbol names over.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
This series should rid us of dtbs_check errors for the RISC-V Canaan
k210 based boards. To make keeping it that way a little easier, I
changed the Canaan devicetree Makefile so that it would build all of the
devicetrees in the directory if SOC_CANAAN.
Link: https://lore.kernel.org/all/mhng-85044754-c361-40bc-a6a2-7082f35930bb@palmer-ri-x1c9/
* remotes/palmer/riscv-canaan_dt_schema:
riscv: dts: canaan: build all devicetress if SOC_CANAAN
riscv: dts: canaan: add specific compatible for kd233's LCD
riscv: dts: canaan: fix bus {ranges,reg} warnings
riscv: dts: canaan: remove spi-max-frequency from controllers
riscv: dts: canaan: use custom compatible for k210 i2s
riscv: dts: canaan: fix kd233 display spi frequency
riscv: dts: canaan: fix mmc node names
riscv: dts: canaan: fix the k210's timer nodes
riscv: dts: canaan: fix the k210's memory node
dt-bindings: memory-controllers: add canaan k210 sram controller
dt-bindings: display: ili9341: document canaan kd233's lcd
dt-bindings: display: convert ilitek,ili9341.txt to dt-schema
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Enabling the FPU is now a static_key
- Improvements to the Svpbmt support
- CPU topology bindings for a handful of systems
- Support for systems with 64-bit hart IDs
- Many settings have been enabled in the defconfig, including both
support for the StarFive systems and many of the Docker requirements
There are also a handful of cleanups and improvements, as usual.
* tag 'riscv-for-linus-5.20-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (28 commits)
riscv: enable Docker requirements in defconfig
riscv: convert the t-head pbmt errata to use the __nops macro
riscv: introduce nops and __nops macros for NOP sequences
RISC-V: Add fast call path of crash_kexec()
riscv: mmap with PROT_WRITE but no PROT_READ is invalid
riscv/efi_stub: Add 64bit boot-hartid support on RV64
riscv: cpu: Add 64bit hartid support on RV64
riscv: smp: Add 64bit hartid support on RV64
riscv: spinwait: Fix hartid variable type
riscv: cpu_ops_sbi: Add 64bit hartid support on RV64
riscv: dts: sifive: "fix" pmic watchdog node name
riscv: dts: canaan: Add k210 topology information
riscv: dts: sifive: Add fu740 topology information
riscv: dts: sifive: Add fu540 topology information
riscv: dts: starfive: Add JH7100 CPU topology
RISC-V: Add CONFIG_{NON,}PORTABLE
riscv: config: enable SOC_STARFIVE in defconfig
riscv: dts: microchip: Add mpfs' topology information
riscv: Kconfig.socs: Add comments
riscv: Kconfig.erratas: Add comments
...
|
|
Testing & checking the Canaan devicetrees is inconvenient as only the
devicetree corresponding to SOC_CANAAN_K210_DTB_BUILTIN will be built.
Change the Makefile so that all devicetrees are built by default if
SOC_CANAAN but only the one specified by SOC_CANAAN_K210_DTB_BUILTIN
gets built as an object.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220705215213.1802496-14-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Add the recently introduced compatible for the LCD on the Canaan KD233.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220705215213.1802496-13-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The k210 devicetrees warn about missing/empty reg and/or ranges
properties:
arch/riscv/boot/dts/canaan/k210.dtsi:408.22-460.5: Warning (unit_address_vs_reg): /soc/bus@52000000: node has a unit name, but no reg or ranges property
arch/riscv/boot/dts/canaan/k210.dtsi:352.22-406.5: Warning (simple_bus_reg): /soc/bus@50400000: missing or empty reg/ranges property
Add a ranges properties that naively caps the buses after the
allocation of their last devices.
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220705215213.1802496-12-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
spi-max-frequency is a device, not a controller property and should be
removed.
Link: https://lore.kernel.org/lkml/20220526014141.2872567-1-robh@kernel.org/
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220705215213.1802496-11-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The devicetrees using the Canaan k210 all have a sound-dai-cells value
of 1, whereas the standard binding example for the DesignWare i2s and
other use cases suggest 0. Use a k210 specific compatible which
supports this difference.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220705215213.1802496-10-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The binding for the ili9341 specifies a const spi-max-frequency of 10
MHz but the kd233 devicetree entry has it listed at 15 Mhz.
Align the devicetree with the value in the binding.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220705215213.1802496-9-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The newly-converted-to-dt-schema binding expects the mmc node name to be
'^mmc(@.*)?$' so align the devicetree with the schema.
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220705215213.1802496-8-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The timers on the k210 have non standard interrupt configurations,
which leads to dtbs_check warnings:
k210_generic.dtb: timer@502d0000: interrupts: [[14], [15]] is too long
From schema: Documentation/devicetree/bindings/timer/snps,dw-apb-timer.yaml
Split the timer nodes in two, so that the second timer in the IP block
can actually be accessed & in the process solve the dtbs_check warning.
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220705215213.1802496-7-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The k210 U-Boot port has been using the clocks defined in the
devicetree to bring up the board's SRAM, but this violates the
dt-schema. As such, move the clocks to a dedicated node with
the same compatible string. The regs property does not fit in
either node, so is replaced by comments.
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220705215213.1802496-6-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The k210 has no cpu-map node, so tools like hwloc cannot correctly
parse the topology. Add the node using the existing node labels.
Reported-by: Brice Goglin <Brice.Goglin@inria.fr>
Link: https://github.com/open-mpi/hwloc/issues/536
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20220705190435.1790466-6-mail@conchuod.ie
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220624170811.66395-1-krzysztof.kozlowski@linaro.org
Link: https://lore.kernel.org/all/20220616005224.18391-1-krzysztof.kozlowski@linaro.org/
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
According to the K210 Standalone SDK Programming guide:
https://canaan-creative.com/wp-content/uploads/2020/03/kendryte_standalone_programming_guide_20190311144158_en.pdf
Section 15.4.3.3:
SPI0 and SPI1 supports: standard, dual, quad and octal transfers.
SPI3 supports: standard, dual and quad transfers (octal is not supported).
In order to support quad transfers (Quad SPI), SPI3 must have four IO wires
connected to the SPI flash.
Update the device tree to specify the correct bus width.
Tested on maix bit, maix dock and maixduino, which all have the same
SPI flash (gd25lq128d) connected to SPI3. maix go is untested, but it
would not make sense for this k210 board to be designed differently.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Fixes: 8f5b0e79f3e5 ("riscv: Add SiPeed MAIXDUINO board device tree")
Fixes: 8194f08bda18 ("riscv: Add SiPeed MAIX GO board device tree")
Fixes: a40f920964c4 ("riscv: Add SiPeed MAIX DOCK board device tree")
Fixes: 97c279bcf813 ("riscv: Add SiPeed MAIX BiT board device tree")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Commit 67d96729a9e7 ("riscv: Update Canaan Kendryte K210 device tree")
incorrectly removed two entries from the PLIC interrupt-controller node's
interrupts-extended property.
The PLIC driver cannot know the mapping between hart contexts and hart ids,
so this information has to be provided by device tree, as specified by the
PLIC device tree binding.
The PLIC driver uses the interrupts-extended property, and initializes the
hart context registers in the exact same order as provided by the
interrupts-extended property.
In other words, if we don't specify the S-mode interrupts, the PLIC driver
will simply initialize the hart0 S-mode hart context with the hart1 M-mode
configuration. It is therefore essential to specify the S-mode IRQs even
though the system itself will only ever be running in M-mode.
Re-add the S-mode interrupts, so that we get working IRQs on hart1 again.
Cc: <stable@vger.kernel.org>
Fixes: 67d96729a9e7 ("riscv: Update Canaan Kendryte K210 device tree")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for the DA9063 as used on the HiFive Unmatched.
- Support for relative extables, which puts us in line with other
architectures and save some space in vmlinux.
- A handful of kexec fixes/improvements, including the ability to run
crash kernels from PCI-addressable memory on the HiFive Unmatched.
- Support for the SBI SRST extension, which allows systems that do not
have an explicit driver in Linux to reboot.
- A handful of fixes and cleanups, including to the defconfigs and
device trees.
* tag 'riscv-for-linus-5.17-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (52 commits)
RISC-V: Use SBI SRST extension when available
riscv: mm: fix wrong phys_ram_base value for RV64
RISC-V: Use common riscv_cpuid_to_hartid_mask() for both SMP=y and SMP=n
riscv: head: remove useless __PAGE_ALIGNED_BSS and .balign
riscv: errata: alternative: mark vendor_patch_func __initdata
riscv: head: make secondary_start_common() static
riscv: remove cpu_stop()
riscv: try to allocate crashkern region from 32bit addressible memory
riscv: use hart id instead of cpu id on machine_kexec
riscv: Don't use va_pa_offset on kdump
riscv: dts: sifive: fu540-c000: Fix PLIC node
riscv: dts: sifive: fu540-c000: Drop bogus soc node compatible values
riscv: dts: sifive: Group tuples in register properties
riscv: dts: sifive: Group tuples in interrupt properties
riscv: dts: microchip: mpfs: Group tuples in interrupt properties
riscv: dts: microchip: mpfs: Fix clock controller node
riscv: dts: microchip: mpfs: Fix reference clock node
riscv: dts: microchip: mpfs: Fix PLIC node
riscv: dts: microchip: mpfs: Drop empty chosen node
riscv: dts: canaan: Group tuples in interrupt properties
...
|
|
To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped.
Fix this by grouping the tuples of "interrupts" and
"interrupts-extended" properties using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
"make dtbs_check":
arch/riscv/boot/dts/canaan/sipeed_maix_bit.dt.yaml: spi-flash@0: $nodename:0: 'spi-flash@0' does not match '^flash(@.*)?$'
From schema: Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
Fix this by renaming all SPI FLASH nodes to "flash".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The previous commit fixed up all shell scripts to not include
include/config/auto.conf.
Now that include/config/auto.conf is only included by Makefiles,
we can change it into a more Make-friendly form.
Previously, Kconfig output string values enclosed with double-quotes
(both in the .config and include/config/auto.conf):
CONFIG_X="foo bar"
Unlike shell, Make handles double-quotes (and single-quotes as well)
verbatim. We must rip them off when used.
There are some patterns:
[1] $(patsubst "%",%,$(CONFIG_X))
[2] $(CONFIG_X:"%"=%)
[3] $(subst ",,$(CONFIG_X))
[4] $(shell echo $(CONFIG_X))
These are not only ugly, but also fragile.
[1] and [2] do not work if the value contains spaces, like
CONFIG_X=" foo bar "
[3] does not work correctly if the value contains double-quotes like
CONFIG_X="foo\"bar"
[4] seems to work better, but has a cost of forking a process.
Anyway, quoted strings were always PITA for our Makefiles.
This commit changes Kconfig to stop quoting in include/config/auto.conf.
These are the string type symbols referenced in Makefiles or scripts:
ACPI_CUSTOM_DSDT_FILE
ARC_BUILTIN_DTB_NAME
ARC_TUNE_MCPU
BUILTIN_DTB_SOURCE
CC_IMPLICIT_FALLTHROUGH
CC_VERSION_TEXT
CFG80211_EXTRA_REGDB_KEYDIR
EXTRA_FIRMWARE
EXTRA_FIRMWARE_DIR
EXTRA_TARGETS
H8300_BUILTIN_DTB
INITRAMFS_SOURCE
LOCALVERSION
MODULE_SIG_HASH
MODULE_SIG_KEY
NDS32_BUILTIN_DTB
NIOS2_DTB_SOURCE
OPENRISC_BUILTIN_DTB
SOC_CANAAN_K210_DTB_SOURCE
SYSTEM_BLACKLIST_HASH_LIST
SYSTEM_REVOCATION_KEYS
SYSTEM_TRUSTED_KEYS
TARGET_CPU
UNUSED_KSYMS_WHITELIST
XILINX_MICROBLAZE0_FAMILY
XILINX_MICROBLAZE0_HW_VER
XTENSA_VARIANT_NAME
I checked them one by one, and fixed up the code where necessary.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Add the device tree canaan_kd233.dts for the Canaan Kendryte KD233
development board. This device tree enables LEDs, some gpios and
spi/mmc SD card device. The WS2812B RGB LED and the 10 positions rotary
dip switch present on the board are left undefined.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[Palmer: Remove undocumented microphone entry, along with the use.]
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Add the device tree sipeed_maixduino.dts for the SiPeed MAIXDUINO board.
This device tree enables LEDs and spi/mmc SD card device. Additionally,
gpios and i2c are also enabled and mapped to the board header pins as
indicated on the board itself.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
[Palmer: Remove undocumented microphone entry, along with the use.]
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Add the device tree sipeed_maix_go.dts for the SiPeed MAIX GO board.
This device tree enables buttons, LEDs, gpio, i2c and spi/mmc SD card
devices.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
[Palmer: Remove undocumented microphone entry, along with the use.]
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Add the device tree sipeed_maix_dock.dts for the SiPeed MAIX DOCK m1
and m1w boards. This device tree enables LEDs, gpio, i2c and spi/mmc
SD card devices.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
[Palmer: Remove undocumented microphone entry, along with the use.]
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Add the device tree sipeed_maix_bit.dts for the SiPeed MAIX BiT and
MAIX BiTm boards. This device tree enables LEDs, gpio, i2c and spi/mmc
SD card devices.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
[Palmer: Remove undocumented microphone entry, along with the use.]
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Update the Canaan Kendryte K210 base device tree k210.dtsi to define
all supported peripherals of the SoC, their clocks and reset lines.
The device tree file k210.dts is renamed to k210_generic.dts and
becomes the default value selection of the configuration option
SOC_CANAAN_K210_DTB_BUILTIN_SOURCE. No device beside the serial console
is defined by this device tree. This makes this generic device tree
suitable for use with a builtin initramfs with all known K210 based
boards.
These changes result in the K210_CLK_ACLK clock ID to be unused and
removed from the dt-bindings k210-clk.h header file.
Most updates to the k210.dtsi file come from Sean Anderson's work on
U-Boot support for the K210.
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Remove the clocks property from the cpu and clint nodes as these are
ignored. Also remove the clock-frequency property from the cpu nodes as
riscv relies on the timebase-frequency property.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Rename configuration options and directories related to the Kendryte
K210 SoC to use the SoC vendor name (canaan) instead of the "kendryte"
branding name.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
