| Age | Commit message (Collapse) | Author |
|---|
|
Use the common dp link power up/down helpers to avoid duplicating code.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318063452.4983-2-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
At present, the DSI mode configuration check happens during the
_atomic_enable() phase, which is not really the best place for this.
Moreover, if the mode is not valid, the driver gives a warning and
continues the hardware configuration.
Move the DSI mode configuration check to _atomic_check() instead, which
can properly report back any invalid mode, before the _enable phase even
begins.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-10-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Add support for the input format negotiation hook, that uses the helper
drm_mipi_dsi_get_input_bus_fmt() for dsi hosts, to figure out the
required input format.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-9-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Instead of manually finding the next bridge/panel, and maintaining the
panel-bridge (in-case the next entity is a panel), switch to using the
automatically managing devm_drm_of_get_bridge() API.
Drop the drm_panel support completely from the driver while at it.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-7-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Once the DSI Link and DSI Phy are initialized, the code needs to wait
for Clk and Data Lanes to be ready, before continuing configuration.
This is in accordance with the DSI Start-up procedure, found in the
Technical Reference Manual of Texas Instrument's J721E SoC[0] which
houses this DSI TX controller.
If the previous bridge (or crtc/encoder) are configured pre-maturely,
the input signal FIFO gets corrupt. This introduces a color-shift on the
display.
Allow the driver to wait for the clk and data lanes to get ready during
DSI enable.
[0]: See section 12.6.5.7.3 "Start-up Procedure" in J721E SoC TRM
TRM Link: http://www.ti.com/lit/pdf/spruil1
Fixes: e19233955d9e ("drm/bridge: Add Cadence DSI driver")
Cc: stable@vger.kernel.org
Tested-by: Dominik Haller <d.haller@phytec.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-6-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Check for the return value of the phy_mipi_dphy_get_default_config()
call, and in case of an error, return back the same.
Fixes: fced5a364dee ("drm/bridge: cdns: Convert to phy framework")
Cc: stable@vger.kernel.org
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-5-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The crtc_* mode parameters do not get generated (duplicated in this
case) from the regular parameters before the mode validation phase
begins.
The rest of the code conditionally uses the crtc_* parameters only
during the bridge enable phase, but sticks to the regular parameters
for mode validation. In this singular instance, however, the driver
tries to use the crtc_clock parameter even during the mode validation,
causing the validation to fail.
Allow the D-Phy config checks to use mode->clock instead of
mode->crtc_clock during mode_valid checks, like everywhere else in the
driver.
Fixes: fced5a364dee ("drm/bridge: cdns: Convert to phy framework")
Cc: stable@vger.kernel.org
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-4-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The driver code doesn't have a Phy de-initialization path as yet, and so
it does not clear the phy_initialized flag while suspending. This is a
problem because after resume the driver looks at this flag to determine
if a Phy re-initialization is required or not. It is in fact required
because the hardware is resuming from a suspend, but the driver does not
carry out any re-initialization causing the D-Phy to not work at all.
Call the counterparts of phy_init() and phy_power_on(), that are
phy_exit() and phy_power_off(), from _bridge_post_disable(), and clear
the flags so that the Phy can be initialized again when required.
Fixes: fced5a364dee ("drm/bridge: cdns: Convert to phy framework")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-3-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Fix the OF node pointer passed to the of_drm_find_bridge() call to find
the next bridge in the display chain.
The code to find the next panel (and create its panel-bridge) works
fine, but to find the next (non-panel) bridge does not.
To find the next bridge in the pipeline, we need to pass "np" - the OF
node pointer of the next entity in the devicetree chain. Passing
"of_node" to of_drm_find_bridge (which is what the code does currently)
will fetch the bridge for the cdns-dsi which is not what's required.
Fix that.
Fixes: e19233955d9e ("drm/bridge: Add Cadence DSI driver")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-2-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
drm_dp_dpcd_read_link_status() follows the "return error code or number
of bytes read" protocol, with the code returning less bytes than
requested in case of some errors. However most of the drivers
interpreted that as "return error code in case of any error". Switch
drm_dp_dpcd_read_link_status() to drm_dp_dpcd_read_data() and make it
follow that protocol too.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250324-drm-rework-dpcd-access-v4-2-e80ff89593df@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The Cadence DSI driver follows the drm_encoder->crtc pointer that is
deprecated and shouldn't be used by atomic drivers.
Fortunately, the atomic hooks provide the drm_atomic_state and we can
access our current CRTC from that, going from the bridge to its encoder,
to its connector, and to its CRTC.
Let's convert this bridge driver to atomic so we can get rid of the
drm_encoder->crtc dereference.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-12-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
The drm_bridge structure contains an encoder pointer that is widely used
by bridge drivers. This pattern is largely documented as deprecated in
other KMS entities for atomic drivers.
However, one of the main use of that pointer is done in attach to just
call drm_bridge_attach on the next bridge to add it to the bridge list.
While this dereferences the bridge->encoder pointer, it's effectively
the same encoder the bridge was being attached to.
We can make it more explicit by adding the encoder the bridge is
attached to to the list of attach parameters. This also removes the need
to dereference bridge->encoder in most drivers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-1-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
It's pretty inconvenient to access the full atomic state from
drm_bridges, so let's change the atomic_disable hook prototype to pass
it directly.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-4-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
It's pretty inconvenient to access the full atomic state from
drm_bridges, so let's change the atomic_enable hook prototype to pass it
directly.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250213-bridge-connector-v3-3-e71598f49c8f@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
If the clock mhdp->clk was not enabled in cdns_mhdp_probe(), it should not
be disabled in any path.
The return value of clk_prepare_enable() is not checked. If mhdp->clk was
not enabled, it may be disabled in the error path of cdns_mhdp_probe()
(e.g., if cdns_mhdp_load_firmware() fails) or in cdns_mhdp_remove() after
a successful cdns_mhdp_probe() call.
Use the devm_clk_get_enabled() helper function to ensure proper call
balance for mhdp->clk.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: fb43aa0acdfd ("drm: bridge: Add support for Cadence MHDP8546 DPI/DP bridge")
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250214154632.1907425-1-mordan@ispras.ru
|
|
The mode_valid() callbacks of drm_encoder, drm_crtc and drm_bridge
take a const struct drm_display_mode argument. Change the mode_valid
callback of drm_connector to also take a const argument.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241214-drm-connector-mode-valid-const-v2-5-4f9498a4c822@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The v6.13-rc2 release included a bunch of breaking changes,
specifically the MODULE_IMPORT_NS commit.
Backmerge in order to fix them before the next pull-request.
Include the fix from Stephen Roswell.
Caused by commit
25c3fd1183c0 ("drm/virtio: Add a helper to map and note the dma addrs and lengths")
Interacting with commit
cdd30ebb1b9f ("module: Convert symbol namespace to string literal")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://patchwork.freedesktop.org/patch/msgid/20241209121717.2abe8026@canb.auug.org.au
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
|
|
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
cdns_mhdp_hdcp_set_lc() and cdns_mhdp_hdcp_set_public_key_param()
were added by commit
6a3608eae6d3 ("drm: bridge: cdns-mhdp8546: Enable HDCP")
but never used.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241005232017.305217-1-linux@treblig.org
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
Let's start the new release cycle.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
bridge->encoder
In the cdns_mhdp_connector_init() function, the check on the existence
of bridge->encoder is not necessary, as it has already been checked in
the drm_bridge_attach() function. As the cdns_mhdp_connector_init() is
only called by cdns_mhdp_attach(), it is guaranteed that the .encoder
member of the struct drm_bridge is not NULL when cdns_mhdp_attach() gets
called.
Remove the redundant checking codes "if (!bridge->encoder) { ... }".
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240513153109.46786-8-sui.jingfeng@linux.dev
|
|
This reverts commit e075e496f516bf92bc0cbaf94d64e8d4a6b58321, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1ba76cc4d96a8afefff5d1bc42fb1e1329c5da68.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
This reverts commit 0323287de87d7e6e9c22c57d7440aa353a2298d0, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/89ac456805746b6d0c888f10c5120b11aacd3319.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
This reverts commit 3166e7e6d935caaef07605a5c90773fbf9ffeaf4, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/a40e70a0abd3d841c23c107d452a43fdd70ef37a.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
In cdns_mhdp_atomic_enable(), the return value of drm_mode_duplicate() is
assigned to mhdp_state->current_mode, and there is a dereference of it in
drm_mode_set_name(), which will lead to a NULL pointer dereference on
failure of drm_mode_duplicate().
Fix this bug add a check of mhdp_state->current_mode.
Fixes: fb43aa0acdfd ("drm: bridge: Add support for Cadence MHDP8546 DPI/DP bridge")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240408125810.21899-1-amishin@t-argos.ru
|
|
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_HDCP_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-11-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_DP_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-10-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
Most of our helpers have relied on being selected so far through
Kconfig, but that creates issues when we have multiple layers of helpers
with some depending on others.
Indeed, select doesn't select a dependency's dependencies, and thus
isn't super intuitive. Depends on however doesn't have that limitation,
so we can just switch all the drivers that were selecting
DRM_DISPLAY_HELPER to depend on it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-8-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
If EDID read fails, clear the EDID property.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/a754d9f90fe2addb9d90f9638e3d53dce87bdabc.1706038510.git.jani.nikula@intel.com
|
|
Prefer using the struct drm_edid based callback and functions.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/88fde35b8d75860d7a2caad94d774aa96b443754.1706038510.git.jani.nikula@intel.com
|
|
'ret' could be uninitialized at the end of the function, although it's
not clear if that can happen in practice.
Fixes: 6a3608eae6d3 ("drm: bridge: cdns-mhdp8546: Enable HDCP")
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103-uninit-fixes-v2-3-c22b2444f5f5@ideasonboard.com
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-23-u.kleine-koenig@pengutronix.de
|
|
Replace the generic error message issued by the driver core when the remove
callback returns non-zero ("remove callback returned a non-zero value. This
will be ignored.") by a message that tells the actual problem.
Also simplify a bit by checking the return value of wait_event_timeout a
bit later.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102165640.3307820-22-u.kleine-koenig@pengutronix.de
|
|
Three DRM bridge drivers select GENERIC_PHY_MIPI_DPHY when GENERIC_PHY
might not be set. This causes Kconfig warnings and a build error.
WARNING: unmet direct dependencies detected for GENERIC_PHY_MIPI_DPHY
Depends on [n]: GENERIC_PHY [=n]
Selected by [y]:
- DRM_NWL_MIPI_DSI [=y] && DRM_BRIDGE [=y] && DRM [=y] && COMMON_CLK [=y] && OF [=y] && HAS_IOMEM [=y]
- DRM_SAMSUNG_DSIM [=y] && DRM [=y] && DRM_BRIDGE [=y] && COMMON_CLK [=y] && OF [=y] && HAS_IOMEM [=y]
(drm/bridge/cadence/Kconfig was found by inspection.)
aarch64-linux-ld: drivers/gpu/drm/bridge/samsung-dsim.o: in function `samsung_dsim_set_phy_ctrl':
drivers/gpu/drm/bridge/samsung-dsim.c:731: undefined reference to `phy_mipi_dphy_get_default_config_for_hsclk'
Prevent these warnings and build error by also selecting GENERIC_PHY
whenever selecting GENERIC_PHY_MIPI_DPHY.
Fixes: fced5a364dee ("drm/bridge: cdns: Convert to phy framework")
Fixes: 44cfc6233447 ("drm/bridge: Add NWL MIPI DSI host controller support")
Fixes: 171b3b1e0f8b ("drm: bridge: samsung-dsim: Select GENERIC_PHY_MIPI_DPHY")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Aleksandr Nogikh <nogikh@google.com>
Link: lore.kernel.org/r/20230803144227.2187749-1-nogikh@google.com
Cc: Adam Ford <aford173@gmail.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Guido Günther <agx@sigxcpu.org>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Robert Foss <rfoss@kernel.org>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Adam Ford <aford173@gmail.com>
Tested-by: Aleksandr Nogikh <nogikh@google.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804030140.21395-1-rdunlap@infradead.org
|
|
When building with W=1, the following warning occurs.
drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:48:17: warning: ‘anx781x_i2c_addresses’ defined but not used [-Wunused-const-variable=] static const u8 anx781x_i2c_addresses[] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/bridge/analogix/analogix-anx78xx.c:40:17: warning: ‘anx7808_i2c_addresses’ defined but not used [-Wunused-const-variable=] static const u8 anx7808_i2c_addresses[] = {
When CONFIG_IO is disabled, above two variables are not used,
since the place where it is used is inclueded in the macro
CONFIG_OF.
Even for drivers that do not depend on CONFIG_OF, it's almost
always better to leave out the of_match_ptr(), since the only
thing it can possibly do is to save a few bytes of .text if a
driver can be used both with and without it. Hence we remove
all of_match_ptr() used in other places.
Fixes: 0647e7dd3f7a ("drm/bridge: Add Analogix anx78xx support")
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230731021345.219588-1-wangzhu9@huawei.com
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714174545.4056287-1-robh@kernel.org
|
|
When removing the tidss driver, there is a warning reported by
kernel about an unhandled interrupt for mhdp driver.
[ 43.238895] irq 31: nobody cared (try booting with the "irqpoll" option)
... [snipped backtrace]
[ 43.330735] handlers:
[ 43.333020] [<000000005367c4f9>] irq_default_primary_handler threaded [<000000007e02b601>]
cdns_mhdp_irq_handler [cdns_mhdp8546]
[ 43.344607] Disabling IRQ #31
This happens because as part of cdns_mhdp_bridge_hpd_disable, driver tries
to disable the interrupts. While disabling the SW_EVENT interrupts,
it accidentally enables the MBOX interrupts, which are not handled by
the driver.
Fix this with a read-modify-write to update only required bits.
Use the enable / disable function as required in other places.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606082142.23760-9-a-bhatia1@ti.com
|
|
input_bus_flags are specified in drm_bridge_timings (legacy) as well
as drm_bridge_state->input_bus_cfg.flags
The flags from the timings will be deprecated. Bridges are supposed
to validate and set the bridge state flags from atomic_check.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
[a-bhatia1: replace timings in cdns_mhdp_platform_info by input_bus_flags]
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606082142.23760-5-a-bhatia1@ti.com
|
|
With new connector model, mhdp bridge will not create the connector and
SoC driver will rely on format negotiation to setup the encoder format.
Support minimal format negotiations hooks in the drm_bridge_funcs.
Complete format negotiation can be added based on EDID data.
This patch adds the minimal required support to avoid failure
after moving to new connector model.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
[a-bhatia1: Drop the output_fmt check condition]
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606082142.23760-4-a-bhatia1@ti.com
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230318190804.234610-3-u.kleine-koenig@pengutronix.de
|
|
Several source files include drm_crtc_helper.h without needing it or
only to get its transitive include statements; leading to unnecessary
compile-time dependencies.
Drop drm_crtc_helper.h where possible.
v2:
* update commit message (Sam)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230116131235.18917-8-tzimmermann@suse.de
|
|
Add support for wrapper settings for DSI bridge on j721e. Also enable
DPI0
--------------- -----------------------
| -------| |------- |
| DSS | DPI2 |----->| DPI0 | DSI Wrapper |
| -------| |------- |
--------------- -----------------------
As shown above DPI2 output of DSS is connected to DPI0 input of DSI
Wrapper, DSI wrapper gives control wheather to enable/disable DPI0
input. In j721e above is the only configuration supported
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230103101951.10963-6-r-ravikumar@ti.com
|
|
Create a header file for cdns dsi and move structure definations to
prepare for adding j721e wrapper support
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230103101951.10963-5-r-ravikumar@ti.com
|
|
Move the cadence dsi bridge under drm/bridge/cadence directory, to
prepare for adding j721e wrapper support
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230103101951.10963-4-r-ravikumar@ti.com
|
|
Like commit c4f135d643823a86 ("workqueue: Wrap flush_workqueue() using a
macro") says, flush_scheduled_work() is dangerous and will be forbidden.
We are on the way for removing all flush_scheduled_work() callers from
the kernel, and this patch is for removing flush_scheduled_work() call
from cadence driver.
Since cdns-mhdp8546 driver uses 4 works
mhdp->modeset_retry_work
mhdp->hpd_work
mhdp->hdcp.check_work
mhdp->hdcp.prop_work
I assume that flush_scheduled_work() in cdns_mhdp_remove() needs to wait
for only these 4 works.
Since mhdp->modeset_retry_work already uses cancel_work_sync(), I assume
that flush_scheduled_work() needs to wait for only 3 works. But I came to
wonder whether mhdp->hdcp.check_work should be flushed or cancelled.
While flush_scheduled_work() waits for completion of works which were
already queued to system_wq, mhdp->hdcp.check_work is a delayed work.
That is, this work won't be queued to system_wq unless timeout expires.
Current code will wait for mhdp->hdcp.check_work only if timeout already
expired. If timeout is not expired yet, flush_scheduled_work() will fail
to cancel mhdp->hdcp.check_work, and cdns_mhdp_hdcp_check_work() which is
triggered by mhdp->hdcp.check_work will schedule hdcp->check_work, which
is too late for flush_scheduled_work() to wait for completion of
cdns_mhdp_hdcp_prop_work().
But since I couldn't get comments on how do we want to handle this race
window [1], this patch chose "do nothing" for mhdp->hdcp.check_work and
mhdp->hdcp.prop_work. That is, I assume that flush_scheduled_work() in
cdns_mhdp_remove() needs to wait for only mhdp->hpd_work work.
Link: https://lkml.kernel.org/r/943273cb-c2ec-24e3-5edb-64eacc6e2d30@I-love.SAKURA.ne.jp [1]
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/216591bc-28bb-0453-10bb-59e268dff540@I-love.SAKURA.ne.jp
|
|
drm_crtc.h has no need for linux/media-bus-format.h, so don't
include it. Avoids useless rebuilds of the entire universe when
touching linux/media-bus-format.h.
Quite a few placs do currently depend on linux/media-bus-format.h
without actually including it directly. All of those need to be
fixed up.
v2: Deal with ingenic as well
v3: Fix up mxsfb and remaining parts of imx
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-4-ville.syrjala@linux.intel.com
|
|
drm_crtc.h has no need for drm_edid.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching drm_edid.h.
Quite a few placs do currently depend on drm_edid.h without
actually including it directly. All of those need to be fixed
up.
v2: Fix up i915 and msm some more
v3: Fix alphabetical ordering (Sam)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220614090245.30283-1-ville.syrjala@linux.intel.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
|
|
Move DRM's HDCP helper library into the display/ subdirectory and add
it to DRM's display helpers. Split the header file into core and helpers.
Update all affected drivers. No functional changes.
v3:
* fix Kconfig dependencies
v2:
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-7-tzimmermann@suse.de
|
|
Replace the DP-helper module with a display-helper module. The
support for DisplayPort becomes an internal option that drivers
have to select. Update all related Kconfig and Makefile rules.
Besides the existing code for DisplayPort, the new module will
contain helpers for other video-output standards, such as HDMI.
Drivers will have to select their required video-output helpers.
Linking all display-related code into a single module avoids the
proliferation of small kernel modules.
The module parameters drm_dp_cec_unregister_delay, dp_aux_i2c_speed_khz,
and dp_aux_i2c_transfer_size are moving from the drm_dp_helper namespace
to drm_display_helper.
v2:
* mention module parameters in commit message (Javier)
* distiguish between display module and DP support in Kconfig
* update Makefile rules for DP helpers
* move Kconfig rules into separate file under display/
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-4-tzimmermann@suse.de
|
