| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / iio driver updates from Greg KH:
"Here is the big char/misc/iio and other small driver subsystem pull
request for 6.16-rc1.
Overall, a lot of individual changes, but nothing major, just the
normal constant forward progress of new device support and cleanups to
existing subsystems. Highlights in here are:
- Large IIO driver updates and additions and device tree changes
- Android binder bugfixes and logfile fixes
- mhi driver updates
- comedi driver updates
- counter driver updates and additions
- coresight driver updates and additions
- echo driver removal as there are no in-kernel users of it
- nvmem driver updates
- spmi driver updates
- new amd-sbi driver "subsystem" and drivers added
- rust miscdriver binding documentation fix
- other small driver fixes and updates (uio, w1, acrn, hpet,
xillybus, cardreader drivers, fastrpc and others)
All of these have been in linux-next for quite a while with no
reported problems"
* tag 'char-misc-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (390 commits)
binder: fix yet another UAF in binder_devices
counter: microchip-tcb-capture: Add watch validation support
dt-bindings: iio: adc: Add ROHM BD79100G
iio: adc: add support for Nuvoton NCT7201
dt-bindings: iio: adc: add NCT7201 ADCs
iio: chemical: Add driver for SEN0322
dt-bindings: trivial-devices: Document SEN0322
iio: adc: ad7768-1: reorganize driver headers
iio: bmp280: zero-init buffer
iio: ssp_sensors: optimalize -> optimize
HID: sensor-hub: Fix typo and improve documentation
iio: admv1013: replace redundant ternary operator with just len
iio: chemical: mhz19b: Fix error code in probe()
iio: adc: at91-sama5d2: use IIO_DECLARE_BUFFER_WITH_TS
iio: accel: sca3300: use IIO_DECLARE_BUFFER_WITH_TS
iio: adc: ad7380: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: adc: ad4695: rename AD4695_MAX_VIN_CHANNELS
iio: adc: ad4695: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: introduce IIO_DECLARE_BUFFER_WITH_TS macros
iio: make IIO_DMA_MINALIGN minimum of 8 bytes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- "hung_task: extend blocking task stacktrace dump to semaphore" from
Lance Yang enhances the hung task detector.
The detector presently dumps the blocking tasks's stack when it is
blocked on a mutex. Lance's series extends this to semaphores
- "nilfs2: improve sanity checks in dirty state propagation" from
Wentao Liang addresses a couple of minor flaws in nilfs2
- "scripts/gdb: Fixes related to lx_per_cpu()" from Illia Ostapyshyn
fixes a couple of issues in the gdb scripts
- "Support kdump with LUKS encryption by reusing LUKS volume keys" from
Coiby Xu addresses a usability problem with kdump.
When the dump device is LUKS-encrypted, the kdump kernel may not have
the keys to the encrypted filesystem. A full writeup of this is in
the series [0/N] cover letter
- "sysfs: add counters for lockups and stalls" from Max Kellermann adds
/sys/kernel/hardlockup_count and /sys/kernel/hardlockup_count and
/sys/kernel/rcu_stall_count
- "fork: Page operation cleanups in the fork code" from Pasha Tatashin
implements a number of code cleanups in fork.c
- "scripts/gdb/symbols: determine KASLR offset on s390 during early
boot" from Ilya Leoshkevich fixes some s390 issues in the gdb
scripts
* tag 'mm-nonmm-stable-2025-05-31-15-28' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (67 commits)
llist: make llist_add_batch() a static inline
delayacct: remove redundant code and adjust indentation
squashfs: add optional full compressed block caching
crash_dump, nvme: select CONFIGFS_FS as built-in
scripts/gdb/symbols: determine KASLR offset on s390 during early boot
scripts/gdb/symbols: factor out pagination_off()
scripts/gdb/symbols: factor out get_vmlinux()
kernel/panic.c: format kernel-doc comments
mailmap: update and consolidate Casey Connolly's name and email
nilfs2: remove wbc->for_reclaim handling
fork: define a local GFP_VMAP_STACK
fork: check charging success before zeroing stack
fork: clean-up naming of vm_stack/vm_struct variables in vmap stacks code
fork: clean-up ifdef logic around stack allocation
kernel/rcu/tree_stall: add /sys/kernel/rcu_stall_count
kernel/watchdog: add /sys/kernel/{hard,soft}lockup_count
x86/crash: make the page that stores the dm crypt keys inaccessible
x86/crash: pass dm crypt keys to kdump kernel
Revert "x86/mm: Remove unused __set_memory_prot()"
crash_dump: retrieve dm crypt keys in kdump kernel
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq cleanups from Thomas Gleixner:
"A set of cleanups for the generic interrupt subsystem:
- Consolidate on one set of functions for the interrupt domain code
to get rid of pointlessly duplicated code with only marginal
different semantics.
- Update the documentation accordingly and consolidate the coding
style of the irqdomain header"
* tag 'irq-cleanups-2025-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
irqdomain: Consolidate coding style
irqdomain: Fix kernel-doc and add it to Documentation
Documentation: irqdomain: Update it
Documentation: irq-domain.rst: Simple improvements
Documentation: irq/concepts: Minor improvements
Documentation: irq/concepts: Add commas and reflow
irqdomain: Improve kernel-docs of functions
irqdomain: Make struct irq_domain_info variables const
irqdomain: Use irq_domain_instantiate()'s return value as initializers
irqdomain: Drop irq_linear_revmap()
pinctrl: keembay: Switch to irq_find_mapping()
irqchip/armada-370-xp: Switch to irq_find_mapping()
gpu: ipu-v3: Switch to irq_find_mapping()
gpio: idt3243x: Switch to irq_find_mapping()
sh: Switch to irq_find_mapping()
powerpc: Switch to irq_find_mapping()
irqdomain: Drop irq_domain_add_*() functions
powerpc: Switch irq_domain_add_nomap() to use fwnode
thermal: Switch to irq_domain_create_linear()
soc: Switch to irq_domain_create_*()
...
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: New device support, features and cleanup for 6.16 - take 2
Note - last minute rebase was to drop a typo patch that I'd accidentally
picked up (in the microblaze arch Kconfig)
Take 2 is due to that rebase messing up some fixes tags that were
referring to patches after that point.
There is a known merge conflict due to changes in neighbouring lines.
Stephen's resolution in linux-next is:
https://lore.kernel.org/linux-next/20250506155728.65605bae@canb.auug.org.au/
Added 3 named IIO reviewers to MAINTAINERS. This is a reflection of those
who have been doing much of this work for some time. Lars-Peter is
removed from the entry having moved on to other topics. Thanks
Nuno, David and Andy for stepping up and Lars-Peter for all your
hard work in the past!
Includes the usual mix of new device support, features and general
cleanup.
This time we also have some tree wide changes.
- Rip out the iio_device_claim_direct_scoped() as it proved hard to work
with. This series includes quite a few related cleanups such as use
of guard or factoring code out to allow direct returns.
- Switch from iio_device_claim/release_direct_mode() to new
iio_device_claim/release_direct() which is structured so that sparse
can warn on failed releases. There were a few false positives but
those were mostly in code that benefited from being cleaned up as part
of this process.
- Introduce iio_push_to_buffers_with_ts() to replace the _timestamp()
version over time. This version takes the size of the supplied buffer
which the core checks is at least as big as expected by calculation
from channel descriptions of those channels enabled. Use this in
an initial set of drivers.
- Add macros for IIO_DECLARE_BUFFER_WITH_TS() and
IIO_DECLARE_DMA_BUFFER_WITH_TS() to avoid lots of fiddly code to ensure
correctly aligned buffers for timestamps being added onto the end of
channel data.
New device support
------------------
adi,ad3530r
- New driver for AD3530, AD3530R, AD3531 and AD3531R DACs with
programmable gain controls. R variants have internal references.
adi,ad7476
- Add support (dt compatible only) for the Rohm BU79100G ADC which is
fully compatible with the ti,ads7866.
adi,ad7606
- Support ad7606c-16 and ad7606c-18 devices. Includes switch to dynamic
channel information allocation.
adi,ad7380
- Add support for the AD7389-4
dfrobot,sen0322
- New driver for this oxygen sensor.
mediatek,mt2701-auxadc
- Add binding for MT6893 which is fully compatible with already supported
MT8173.
meson-saradc
- Support the GXLX SoCs. Mostly this is a workaround for some unrelated
clock control bits found in the ADC register map.
nuvoton,nct7201
- New driver for NCT7201 and NCT7202 I2C ADCs.
rohm,bd79124
- New driver for this 12-bit, 8-channel SAR ADC.
- Switch to new set_rv etc gpio callbacks that were added in 6.15.
rohm,bd79703
- Add support for BD79700, BD79701 and BD79702 DACs that have subsets of
functionality of the already supported bd79703. Included making this
driver suitable for support device variants.
st,stm32-lptimer
- Add support for stm32pm25 to this trigger.
Features
--------
Beyond IIO
- Property iterator for named children.
core
- Enable writes for 64 bit integers used for standard IIO ABI elements.
Previously these could be read only.
- Helper library that should avoid code duplication for simpler ADC
bindings that have a child node per channel.
- Enforce that IIO_DMA_MINALIGN is always at least 8 (almost always true
and simplifies code on all significant architectures)
core/backend
- Add support to control source of data - useful when the HDL includes
things like generated ramps for testing purposes. Enable this for
adi-axi-dac
adi,ad3552-hs
- Add debugfs related callbacks to allow debug access to register contents.
adi,ad4000
- Support SPI offload with appropriate FPGA firmware along with improving
documentation.
adi,ad7293
- Add support for external reference voltage.
adi,ad7606
- Support SPI offload.
adi,ad7768-1
- Support reset GPIO.
adi,admv8818
- Support filter frequencies beyond 2^32.
adi,adxl345
- Add single and double tap events.
hid-sensor-prox
- Support 16-bit report sizes as seen on some Intel platforms.
invensense,icm42600
- Enable use of named interrupts to avoid problems with some wiring choices.
Get the interrupt by name, but fallback to previous assumption on the first
being INT1 if no names are supplied.
microchip,mcp3911
- Add reset gpio support.
rohm,bh7150
- Add reset gpio support.
st,stm32
- Add support to control oversampling.
ti,adc128s052
- Add support for ROHM BD79104 which is early compatible with the TI
parts already supported by this driver. Includes some general driver
cleanup and a separate dt binding.
- Simplify reference voltage handling by assuming it is fixed after enabling
the supply.
winsen,mhz19b
- New driver for this C02 sensor.
Cleanup and minor fixes
-----------------------
dt-bindings
- Correct indentation and style for DTS examples.
- Use unevalutateProperties for SPI devices instead of additionalProperties
to allow generic SPI properties from spi-peripheral-props.yaml
ABI Docs
- Add missing docs for sampling_frequency when it applies only to events.
Treewide
- Various minor tweaks, comment fixes and similar.
- Sort TI ADCs in Kconfig that had gotten out of order.
- Switch various drives that provide GPIO chip functionality to the new
callbacks with return values.
- Standardize on { } formatting for all array sentinels.
- Make use of aligned_s64 in a few places to replace either wrong types
or manually defined equivalents.
- Drop places where spi bits_per_word is set to 8 because that is the
default anyway.
adi,ad_sigma_delta library
- Avoid a potential use of uninitialized data if reg_size has a value
that is not supported (no drivers hit this but it is reasonable hardening)
adi,ad4030
- Add error checking for scan types and no longer store it in state.
- Rework code to reduce duplication.
- Move setting the mode from buffer preenable() to update_scan_mode(),
better matching expected semantics of the two different callbacks.
- Improve data marshalling comments.
adi,ad4695
- Use u16 for buffer elements as oversampling is not yet supported except
with SPI offload (which doesn't use this path).
adi,ad5592r
- Clean up destruction of mutexes.
- Use lock guards to simplify code (later patch fixes a missed unlock)
adi,ad5933
- Correct some incorrect settling times.
adi,ad7091
- Deduplicate handling of writable vs volatile registers as they are the
inverse of each other for this device.
adi,ad7124
- Fix 3db Filter frequency.
- Remove ability to directly write the filter frequency (which was broken)
- Register naming improvements.
adi,ad7606
- Add a missing return value check.
- Fill in max sampling rates for all chips.
- Use devm_mutex_init()
- Fix up some kernel-doc formatting issues.
- Remove some camel case that snuck in.
- Drop setting address field in channels as easily established from other
fields.
- Drop unnecessary parameter to ad76060_scale_setup_cb_t.
adi,ad7768-1
- Convert to regmap.
- Factor out buffer allocation.
- Tidy up headers.
adi,ad7944
- Stop setting bits_per_word in SPI xfers with no data.
adi,ad9832
- Add of_device_id table rather than just relying on fallbacks.
- Use FIELD_PREP() to set values of fields.
adi,admv1013
- Cleanup a pointless ternary.
adi,admv8818
- Fix up LPF Band 5 frequency which was slightly wrong.
- Fix an integer overflow.
- Fix range calculation
adi,adt7316
- Replace irqd_get_trigger_type(irq_get_irq_data()) with simpler
irq_get_trigger_type()
adi,adxl345
- Use regmap cache instead of various state variables that were there to
reduce bus accesses.
- Make regmap return value checking consistent across all call sites.
adi,axi-dac
- Add a check on number of channels (0 to 15 valid)
allwinner,sun20i
- Use new adc-helpers to replace local parsing code for channel nodes.
bosch,bmp290
- Move to local variables for sensor data marshalling removing the need
for a messy definition that has to work for all supported parts.
Follow up fix adds a missing initialization.
dynaimage,al3010 and dynaimage,al3320a
- Various minor cleanup to bring these drivers inline with reviewed feedback
given on a new driver.
- Fix an error path in which power down is not called when it should be.
- Switch to regmap.
google,cros_ec
- Fix up a flexible array in middle of structure warning.
- Flush fifo when changing the timeout to avoid potential long wait
for samples.
hid-sensor-rotation
- Remove an __aligned(16) marking that doesn't seem to be justified.
kionix,kxcjk-1013
- Deduplicate code for setting up interrupts.
microchip,mcp3911
- Fix handling of conversion results register which differs across supported
devices.
idt,zopt2201
- Avoid duplicating register lists as all volatile registers are the
inverse of writeable registers on this device.
renesas,rzg2l
- Use new adc-helpers to replace local parsing code for channel nodes.
ti,ads1298
- Fix a missing Kconfig dependency.
* tag 'iio-for-6.16a-take2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (260 commits)
dt-bindings: iio: adc: Add ROHM BD79100G
iio: adc: add support for Nuvoton NCT7201
dt-bindings: iio: adc: add NCT7201 ADCs
iio: chemical: Add driver for SEN0322
dt-bindings: trivial-devices: Document SEN0322
iio: adc: ad7768-1: reorganize driver headers
iio: bmp280: zero-init buffer
iio: ssp_sensors: optimalize -> optimize
HID: sensor-hub: Fix typo and improve documentation
iio: admv1013: replace redundant ternary operator with just len
iio: chemical: mhz19b: Fix error code in probe()
iio: adc: at91-sama5d2: use IIO_DECLARE_BUFFER_WITH_TS
iio: accel: sca3300: use IIO_DECLARE_BUFFER_WITH_TS
iio: adc: ad7380: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: adc: ad4695: rename AD4695_MAX_VIN_CHANNELS
iio: adc: ad4695: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: introduce IIO_DECLARE_BUFFER_WITH_TS macros
iio: make IIO_DMA_MINALIGN minimum of 8 bytes
iio: pressure: zpa2326_spi: remove bits_per_word = 8
iio: pressure: ms5611_spi: remove bits_per_word = 8
...
|
|
I've used several email addresses and a previous name to contribute.
Consolidate all of these to my primary email and update my name.
Link: https://lkml.kernel.org/r/20250517223237.15647-2-casey.connolly@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Add Nuvoton NCT7201/NCT7202 system voltage monitor 12-bit ADC driver
NCT7201/NCT7202 supports up to 12 analog voltage monitor inputs and up
to 4 SMBus addresses by ADDR pin. Meanwhile, ALERT# hardware event pins
for independent alarm signals, and all the threshold values could be set
for system protection without any timing delay. It also supports reset
input RSTIN# to recover system from a fault condition.
Currently, only single-edge mode conversion and threshold events are
supported.
Signed-off-by: Eason Yang <j2anfernee@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250512083156.3300006-3-j2anfernee@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Remove kernel.h since it adds a lot of unnecessary dependencies.
Add specific headers to ensure all functions and macros used in the driver
are directly declared.
Suggested-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/1f7677d31a0165cb30d7eb3b4d613e1337937f9a.1746662899.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use IIO_DECLARE_BUFFER_WITH_TS() to declare the buffer that gets used
with iio_push_to_buffers_with_ts(). This makes the code a bit easier to
read and understand.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-7-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use IIO_DECLARE_DMA_BUFFER_WITH_TS() to declare the buffer that gets
used with iio_push_to_buffers_with_ts(). This makes the code a bit
easier to read and understand.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-5-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Rename AD4695_MAX_CHANNELS to AD4695_MAX_VIN_CHANNELS. It has been a
point of confusion that this macro is only the voltage input channels
and not all channels.
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-4-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use IIO_DECLARE_DMA_BUFFER_WITH_TS() to declare the buffer that gets
used with iio_push_to_buffers_with_ts(). This makes the code a bit
easier to read and understand.
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-3-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Remove setting bits_per_word = 8 from the ti-tsc2046 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-2-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Remove setting bits_per_word = 8 from the ad4030 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-1-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add dependency to Kconfig’s ti-ads1298 because compiling it as a module
failed with an undefined kfifo symbol.
Fixes: 00ef7708fa60 ("iio: adc: ti-ads1298: Add driver")
Signed-off-by: Arthur-Prince <r2.arthur.prince@gmail.com>
Co-developed-by: Mariana Valério <mariana.valerio2@hotmail.com>
Signed-off-by: Mariana Valério <mariana.valerio2@hotmail.com>
Link: https://patch.msgid.link/20250430191131.120831-1-r2.arthur.prince@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
According to Jonathan, variable reference voltages are very rare. It is
unlikely it is needed, and supporting it makes the code a bit more
complex.
Simplify the driver and drop the variable vref support.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/59106e24332743a7f9eb0b13ad6a2f5595ab485a.1745823530.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Currently, SPI-Engine offload module always sends 32-bit data elements to
DMA engine. Appropriately, when set for SPI offloading, the IIO driver uses
32 storagebits for IIO ADC channel buffer elements. However, setting SPI
transfer length according to storagebits (32-bits in case of offload) can
lead to unnecessarily long transfers for ADCs that are 16-bit or less
precision. Adjust AD4000 single-shot read to run transfers of 2 bytes when
that is enough to get all ADC data bits.
Fixes: 59b51edf717b ("iio: adc: ad4000: Add support for SPI offload")
Suggested-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/8f765cfd6e93fad4e755dd95d709b7bea2a388e2.1744718916.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for optional HW reset.
If specified, a reset will be asserted during driver probe.
Co-developed-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250428-mcp3911-fixes-v2-3-406e39330c3d@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The conversion result registers differs between devices. Make sure the
mapping is correct by using a device dependent .get_raw() callback function.
Fixes: 732ad34260d3 ("iio: adc: mcp3911: add support for the whole MCP39xx family")
Co-developed-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250428-mcp3911-fixes-v2-1-406e39330c3d@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Change the type of the buffer elements to u16 since we currently only
support 16-bit word size. The code was originally written to also allow
for 32-bit word size when oversampling is enabled, but so far,
oversampling is only implemented when using SPI offload and therefore
doesn't use this buffer.
AD4695_MAX_CHANNEL_SIZE macro is dropped since it no longer adds any
value.
AD4695_MAX_CHANNELS + 2 is changed to AD4695_MAX_CHANNELS + 1 because
previously we were overallocating. AD4695_MAX_CHANNELS is the number of
of voltage channels and + 1 is for the temperature channel.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Link: https://patch.msgid.link/20250428-iio-introduce-iio_declare_buffer_with_ts-v4-2-6f7f6126f1cb@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use struct with aligned_s64 timestamp to make timestamp alignment
explicit. Technically, what we have works because for all known
architectures, IIO_DMA_MINALIGN is a multiple of __alignof__(s64).
But this way, we don't have to make people read the comments to know
why there are extra elements in each buffer.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250428-iio-adc-ad7606-fix-buffer-alignment-v1-1-88dfc57e5df0@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Validate the scan mask when SPI offloading is being used.
Since this family of ADCs is simultaneous sampling, there isn't a way
to selectively disable channels when reading sample data. (Technically,
AD7616 has a sequencer so the driver could have some control, but that
is for another day).
For "regular" IIO triggered buffer reads, this isn't a problem and the
IIO core will demux the data and ignore data from disabled channels.
However, since SPI offloading is done completely in hardware, we don't
have a way to do the same. So before this patch, if less than all
channels were enabled, the data would be misplaced in the buffer.
By adding a check in update_scan_mode, we can fail to enable the buffer
instead of having bad data returned to userspace.
Fixes: e96d35faf357 ("iio: adc: ad7606: add SPI offload support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250502-iio-adc-ad7606_spi-fix-offload-scan-mask-check-v2-1-e70c6d71baa3@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Both ad7091r_writeable_reg() and ad7091r_volatile_reg() perform the
same test, checking whether a given 'reg' code is
AD7091R_REG_RESULT or AD7091R_REG_ALERT. As the volatile ad7091r
registers happen to be the only read-only ones, the volatile_reg()
function now returns the negated output of writeable_reg().
Co-developed-by: Bruno Stephan <bruno.stephan@usp.br>
Signed-off-by: Bruno Stephan <bruno.stephan@usp.br>
Co-developed-by: Andre de Lima <aschwarz@usp.br>
Signed-off-by: Andre de Lima <aschwarz@usp.br>
Signed-off-by: Arthur Pilone <art.pilone@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://patch.msgid.link/20250421145534.91146-1-arthurpilone@usp.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix a typo,(PAC1934 -> PAC193X), into the link from an application note
related to the ACPI device definition.
Fixes: 0fb528c8255b ("iio: adc: adding support for PAC193x")
Reported-by: Matteo Martelli <matteomartelli3@gmail.com>
Closes: https://patch.msgid.link/172794015844.2520.11909797050797595912@njaxe.localdomain
Signed-off-by: Marius Cristea <marius.cristea@microchip.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250424-pac1934-doc_link-v1-1-9832445cb270@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add oversampling support for STM32H7, STM32MP15 & STM32MP13.
STM32F4 ADC has no oversampling feature.
The current support of the oversampling feature aims at increasing the
data SNR, without changing the data resolution.
As the oversampling by itself increases data resolution, a right shift
is applied to keep the initial resolution.
Only the oversampling ratio corresponding to a power of two are
supported here, to get a direct link between right shift and
oversampling ratio. (2^n ratio <=> n right shift)
The oversampling ratio is shared by all channels, whatever channel type.
(e.g. single ended or differential).
Oversampling can be configured using IIO ABI:
- oversampling_ratio_available
- oversampling_ratio
Co-developed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250424151604.626758-1-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use a struct with aligned s64_timestamp instead of a padded array for
the buffer used for iio_push_to_buffers_with_ts(). This makes it easier
to see the correctness of the size and alignment of the buffer.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250418-iio-prefer-aligned_s64-timestamp-v1-3-4c6080710516@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Follow the pattern of other drivers and use aligned_s64 for the
timestamp. This will ensure that the timestamp is correctly aligned on
all architectures. It also ensures that the struct itself it also 8-byte
aligned so we can drop the explicit __aligned(8) attribute.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250417-iio-more-timestamp-alignment-v1-2-eafac1e22318@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
checks.
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-10-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
length sanity check.
By providing the size of the buffer used, runtime checks can be performed
to ensure not overrun.
Also change the pushed data pointer to be that of the structure that also
contains the timestamp. Not an actual bug but semantically incorrect to
push the channel data when we want the storage with the timestamp as well.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-9-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
irq_domain_add_simple() is going away as being obsolete now. Switch to
the preferred irq_domain_create_simple(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-21-jirislaby@kernel.org
|
|
Apply a mask to the raw value received over the SPI bus for unsigned
direct reads. As we found recently, SPI controllers may not set unused
bits to 0 when reading with bits_per_word != {8,16,32}. The ad7944 uses
bits_per_word of 14 and 18, so we need to mask the value to be sure we
returning the correct value to userspace during a direct read.
Fixes: d1efcf8871db ("iio: adc: ad7944: add driver for AD7944/AD7985/AD7986")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-adc-ad7944-max-high-bits-on-direct-read-v1-1-b173facceefe@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The pointer returned from ad4851_parse_channels_common() is incremented
internally as each channel is populated. In ad4858_parse_channels(),
the same pointer was further incremented while setting ext_scan_type
fields for each channel. This resulted in indio_dev->channels being set
to a pointer past the end of the allocated array, potentially causing
memory corruption or undefined behavior.
Fix this by iterating over the channels using an explicit index instead
of incrementing the pointer. This preserves the original base pointer
and ensures all channel metadata is set correctly.
Fixes: 6250803fe2ec ("iio: adc: ad4851: add ad485x driver")
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250509101657.6742-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix incorrect value mask for register write. Register values are 8-bit,
not 9. If this function was called with a value > 0xFF and an even addr,
it would cause writing to the next register.
Fixes: f2a22e1e172f ("iio: adc: ad7606: Add support for software mode for ad7616")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250428-iio-adc-ad7606_spi-fix-write-value-mask-v1-1-a2d5e85a809f@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix 18-bit raw read for 18-bit chips by applying a mask to the value
we receive from the SPI controller.
SPI controllers either return 1, 2 or 4 bytes per word depending on the
bits_per_word. For 16-bit chips, there was no problem since they raw
data fit exactly in the 2 bytes received from the SPI controller. But
now that we have 18-bit chips and we are using bits_per_word = 18, we
cannot assume that the extra bits in the 32-bit word are always zero.
In fact, with the AXI SPI Engine controller, these bits are not always
zero which caused the raw values to read 10s of 1000s of volts instead
of the correct value. Therefore, we need to mask the value we receive
from the SPI controller to ensure that only the 18 bits of real data
are used.
Fixes: f3838e934dff ("iio: adc: ad7606: add support for AD7606C-{16,18} parts")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250502-iio-adc-ad7606-fix-raw-read-for-18-bit-chips-v1-1-06caa92d8f11@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix compiling the ad7173 driver when CONFIG_GPIOLIB is not set by
selecting GPIOLIB to be always enabled and remove the #if.
Commit 031bdc8aee01 ("iio: adc: ad7173: add calibration support") placed
unrelated code in the middle of the #if IS_ENABLED(CONFIG_GPIOLIB) block
which caused the reported compile error.
However, later commit 7530ed2aaa3f ("iio: adc: ad7173: add openwire
detection support for single conversions") makes use of the gpio regmap
even when we aren't providing gpio controller support. So it makes more
sense to always enable GPIOLIB rather than trying to make it optional.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504220824.HVrTVov1-lkp@intel.com/
Fixes: 031bdc8aee01 ("iio: adc: ad7173: add calibration support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250422-iio-adc-ad7173-fix-compile-without-gpiolib-v1-1-295f2c990754@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use `\t(\{ ?\},|\{\}|\{\s*/\*.*\*/\s*\},?)$` regex to find and replace
the array sentinel in all IIO drivers to the same style.
For some time, we've been trying to consistently use `{ }` (no trailing
comma, no comment, one space between braces) for array sentinels in the
IIO subsystem. Still nearly 50% of existing code uses a different style.
To save reviewers from having to request this trivial change as
frequently, let's normalize the style in all existing IIO drivers.
At least when code is copy/pasted to new drivers, the style will be
consistent.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250411-iio-sentinel-normalization-v1-1-d293de3e3d93@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This change moves the buffer allocation and related trigger allocation
in a separate function, making space for adding another type of iio
buffer if needed.
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Link: https://patch.msgid.link/11c1777b406875ce1a7216dc4b094ff99af8da7f.1744325346.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Implement asynchronous hardware reset GPIO.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Co-developed-by: Jonathan Santos <Jonathan.Santos@analog.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Link: https://patch.msgid.link/25a413babeddf29583f1c26abf4234dfd606a595.1744325346.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Convert the AD7768-1 driver to use the regmap API for register
access. This change simplifies and standardizes register interactions,
reducing code duplication and improving maintainability.
Create two regmap configurations, one for 8-bit register values and
other for 24-bit register values.
Since we are using regmap now, define the remaining registers from 0x32
to 0x34.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Link: https://patch.msgid.link/aec9e5452c1ac16d5379a80dfce97c00d85614a2.1744325346.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix Smatch-detected issue:
drivers/iio/adc/ad_sigma_delta.c:604 ad_sd_trigger_handler() error:
uninitialized symbol 'status_pos'.
The variable `status_pos` was only initialized in specific switch cases
(1, 2, 3, 4), which could leave it uninitialized if `reg_size` had an
unexpected value.
Fix by adding a default case to the switch block to catch unexpected
values of `reg_size`. Use `dev_err_ratelimited()` for error logging and
`goto irq_handled` instead of returning early.
Signed-off-by: Purva Yeshi <purvayeshi550@gmail.com>
Link: https://patch.msgid.link/20250410170408.8585-1-purvayeshi550@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ROHM BD79104 ADC has identical SPI communication logic as the
ti-adc128s052. Eg, SPI transfer should be 16 clk cycles, conversion is
started when the CS is pulled low, and channel selection is done by
writing the channel ID after two zero bits. Data is contained in
big-endian format in the last 12 bits.
The BD79104 has two input voltage pins. Data sheet uses terms "vdd" and
"iovdd". The "vdd" is used also as an analog reference voltage. Hence
the driver expects finding these from the device-tree, instead of having
the "vref" only as TI's driver.
NOTE: The TI's data sheet[1] does show that the TI's IC does actually
have two voltage inputs as well. Pins are called Va (analog reference)
and Vd (digital supply pin) - but I keep the existing driver behaviour
for the TI's IC "as is", because I have no HW to test changes, and
because I have no real need to touch it.
NOTE II: The BD79104 requires SPI MODE 3.
NOTE III: I used evaluation board "BD79104FV-EVK-001" made by ROHM. With
this board I had to drop the SPI speed below the 20M which is mentioned
in the data-sheet [2]. This, however, may be a limitation of the EVK
board, not the component itself.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Datasheet: https://www.ti.com/lit/ds/symlink/adc128s052.pdf # [1]
Datasheet: https://fscdn.rohm.com/en/products/databook/datasheet/ic/data_converter/dac/bd79104fv-la-e.pdf # [2]
Link: https://patch.msgid.link/36ffa72cbdf8dbbdf1e612040db82ebcdf73fa24.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Error path in ADC reading function can be slighly simplified using the
guard(mutex).
Use guard(mutex) and document the mutex purpose.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/c4262cbf55748d505a74249d2bf46d7c3594d838.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Quoting Jonathan:
"Whilst it doesn't bring huge advantage, now we have devm_mutex_init()
it seems reasonable to use it and maybe catch a use after free for the
lock"
Switch to use devm_mutex_init() while working on this file.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/efe4a039e2bfbf4dcf30743f6b7b88fce3b9ee39.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ti-adc128s052 driver has NULL terminated ID arrays for the
of_device_id, spi_device_id and acpi_device_id. All of these are
terminated by having an empty string as the last member of an array.
Only the of_device_id array uses the /* sentinel */ comment.
It's better to be consistent.
This /* sentinel */ comment serves no real purpose these days as people
are used to seeing these ID lists terminated with an empty array
element.
Drop the /* sentinel */ from the of_device_id.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/bb58002accc696bd4a8fbbab37100c6fa0c29941.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The register data is 12-bit big-endian data. Use be16_to_cpu() to do
the conversion, and simple bitwise AND for masking to make it more
obvious.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/8202060d90221beb9b8cf467606641349ad47fe9.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250409-gpiochip-set-rv-iio-v2-5-4b36428f39cb@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250409-gpiochip-set-rv-iio-v2-4-4b36428f39cb@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The new GPIO callbacks 'set_rv' and 'set_multiple_rv' allow returning a
success code to indicate failures when setting GPIO status. Use them to
allow callers to know when things go south.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/Z_N_J52IZ2IaWawl@mva-rohm
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add SPI offload support for this family.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250403-wip-bl-spi-offload-ad7606-v1-3-1b00cb638b12@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add chip info for AD7389-4 to the ad7380 driver.
This is essentially the same as ad7380-4 except that it is internal-
reference-only instead of external-reference-only.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250401-iio-ad7380-add-ad7389-4-v1-4-23d2568aa24f@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Move the internal reference voltage value to the chip_info structure.
Before this change, only ADAQ chips could be internal_ref_only and only
non-ADAQ chips could be external_ref_only. Now, this restriction is
removed.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250401-iio-ad7380-add-ad7389-4-v1-3-23d2568aa24f@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
