| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq driver updates from Thomas Gleixner:
- Support for hard indices on RISC-V. The hart index identifies a hart
(core) within a specific interrupt domain in RISC-V's Priviledged
Architecture.
- Rework of the RISC-V MSI driver
This moves the driver over to the generic MSI library and solves the
affinity problem of unmaskable PCI/MSI controllers. Unmaskable
PCI/MSI controllers are prone to lose interrupts when the MSI message
is updated to change the affinity because the message write consists
of three 32-bit subsequent writes, which update address and data. As
these writes are non-atomic versus the device raising an interrupt,
the device can observe a half written update and issue an interrupt
on the wrong vector. This is mitiated by a carefully orchestrated
step by step update and the observation of an eventually pending
interrupt on the CPU which issues the update. The algorithm follows
the well established method of the X86 MSI driver.
- A new driver for the RISC-V Sophgo SG2042 MSI controller
- Overhaul of the Renesas RZQ2L driver
Simplification of the probe function by using devm_*() mechanisms,
which avoid the endless list of error prone gotos in the failure
paths.
- Expand the Renesas RZV2H driver to support RZ/G3E SoCs
- A workaround for Rockchip 3568002 erratum in the GIC-V3 driver to
ensure that the addressing is limited to the lower 32-bit of the
physical address space.
- Add support for the Allwinner AS23 NMI controller
- Expand the IMX irqsteer driver to handle up to 960 input interrupts
- The usual small updates, cleanups and device tree changes
* tag 'irq-drivers-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
irqchip/imx-irqsteer: Support up to 960 input interrupts
irqchip/sunxi-nmi: Support Allwinner A523 NMI controller
dt-bindings: irq: sun7i-nmi: Document the Allwinner A523 NMI controller
irqchip/davinci-cp-intc: Remove public header
irqchip/renesas-rzv2h: Add RZ/G3E support
irqchip/renesas-rzv2h: Update macros ICU_TSSR_TSSEL_{MASK,PREP}
irqchip/renesas-rzv2h: Update TSSR_TIEN macro
irqchip/renesas-rzv2h: Add field_width to struct rzv2h_hw_info
irqchip/renesas-rzv2h: Add max_tssel to struct rzv2h_hw_info
irqchip/renesas-rzv2h: Add struct rzv2h_hw_info with t_offs variable
irqchip/renesas-rzv2h: Use devm_pm_runtime_enable()
irqchip/renesas-rzv2h: Use devm_reset_control_get_exclusive_deasserted()
irqchip/renesas-rzv2h: Simplify rzv2h_icu_init()
irqchip/renesas-rzv2h: Drop irqchip from struct rzv2h_icu_priv
irqchip/renesas-rzv2h: Fix wrong variable usage in rzv2h_tint_set_type()
dt-bindings: interrupt-controller: renesas,rzv2h-icu: Document RZ/G3E SoC
riscv: sophgo: dts: Add msi controller for SG2042
irqchip: Add the Sophgo SG2042 MSI interrupt controller
dt-bindings: interrupt-controller: Add Sophgo SG2042 MSI
arm64: dts: rockchip: rk356x: Move PCIe MSI to use GIC ITS instead of MBI
...
|
|
Currently, imsic_handle_irq() uses generic_handle_domain_irq() to handle
the interrupt, which internally has an extra step of resolving hwirq using
domain.
Avoid the translation step by replacing the hardware interrupt number with
the Linux interrupt number in the IMSIC vector data and directly call
generic_handle_irq().
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250217085657.789309-10-apatel@ventanamicro.com
|
|
Currently, there is only one "move" pointer in struct imsic_vector so
during vector movement the old vector points to the new vector and new
vector points to itself.
To support forced cleanup of the old vector, add separate "move_next" and
"move_prev" pointers to struct imsic_vector, where during vector movement
the "move_next" pointer of the old vector points to the new vector and the
"move_prev" pointer of the new vector points to the old vector.
Both "move_next" and "move_prev" pointers are cleared separately by
__imsic_local_sync() with a restriction that "move_prev" on the new
CPU is cleared only after the old CPU has cleared "move_next".
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250217085657.789309-8-apatel@ventanamicro.com
|
|
RISC-V distinguishes between memory accesses and device I/O and uses FENCE
instruction to order them as viewed by other RISC-V harts and external
devices or coprocessors. The FENCE instruction can order any combination of
device input(I), device output(O), memory reads(R) and memory
writes(W). For example, 'fence w, o' is used to ensure all memory writes
from instructions preceding the FENCE instruction appear earlier in the
global memory order than device output writes from instructions after the
FENCE instruction.
RISC-V issues IPIs by writing to the IMSIC/ACLINT MMIO registers, which is
regarded as device output operation. However, the existing implementation
of the IMSIC/ACLINT drivers issue the IPI via writel_relaxed(), which does
not guarantee the order of device output operation and preceding memory
writes. As a consequence the hart receiving the IPI might not observe the
IPI related data.
Fix this by replacing writel_relaxed() with writel() when issuing IPIs,
which uses 'fence w, o' to ensure all previous writes made by the current
hart are visible to other harts before they receive the IPI.
Signed-off-by: Xu Lu <luxu.kernel@bytedance.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250127093846.98625-1-luxu.kernel@bytedance.com
|
|
RISC-V IMSIC interrupt controller provides IPI and MSI support.
Currently, DT based drivers setup the IPI feature early during boot but
defer setting up the MSI functionality. However, in ACPI systems, PCI
subsystem is probed early and assume MSI controller is already setup.
Hence, both IPI and MSI features need to be initialized early itself.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/20240812005929.113499-16-sunilvl@ventanamicro.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There was a semantic conflict between 21a8f8a0eb35 ("irqchip: Add RISC-V
incoming MSI controller early driver") and dc892fb44322 ("riscv: Use
IPIs for remote cache/TLB flushes by default") due to an API change.
This manifests as a build failure post-merge.
Reported-by: Tomasz Jeznach <tjeznach@rivosinc.com>
Link: https://lore.kernel.org/all/mhng-10b71228-cf3e-42ca-9abf-5464b15093f1@palmer-ri-x1c9/
Fixes: 0bfbc914d943 ("Merge tag 'riscv-for-linus-6.10-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux")
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20240522184953.28531-3-palmer@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The RISC-V advanced interrupt architecture (AIA) specification
defines a new MSI controller called incoming message signalled
interrupt controller (IMSIC) which manages MSI on per-HART (or
per-CPU) basis. It also supports IPIs as software injected MSIs.
(For more details refer https://github.com/riscv/riscv-aia)
Add an early irqchip driver for RISC-V IMSIC which sets up the
IMSIC state and provide IPIs.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20240307140307.646078-3-apatel@ventanamicro.com
|
