| Age | Commit message (Collapse) | Author |
|---|
|
NIPA tests report that the interface statistics reported
via qstat are lower than those reported via ip link.
Looks like this is because some tests flip the queue
count up and down, and we end up with some of the traffic
accounted on disabled queues.
Add up counters from disabled queues.
Fixes: d888f04c09bb ("virtio-net: support queue stat")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250507003221.823267-3-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We had originally thought to have the mailbox go to ready in the background
while we were doing other things. One issue with this though is that we
can't disable it by clearing the ready state without also blocking
interrupts or calls to mbx_poll as it will just pop back to life during an
interrupt.
In order to prevent that from happening we can pull the code for toggling
to ready out of the interrupt path and instead place it in the
fbnic_mbx_poll_tx_ready path so that it becomes the only spot where the
Rx/Tx can toggle to the ready state. By doing this we can prevent races
where we disable the DMA and/or free buffers only to have an interrupt fire
and undo what we have done.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654722518.499179.11612865740376848478.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This change pulls the call to fbnic_fw_xmit_cap_msg out of
fbnic_mbx_init_desc_ring and instead places it in the polling function for
getting the Tx ready. Doing that we can avoid the potential issue with an
interrupt coming in later from the firmware that causes it to get fired in
interrupt context.
Fixes: 20d2e88cc746 ("eth: fbnic: Add initial messaging to notify FW of our presence")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654721876.499179.9839651602256668493.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There were a couple different issues found in fbnic_mbx_poll_tx_ready.
Among them were the fact that we were sleeping much longer than we actually
needed to as the actual FW could respond in under 20ms. The other issue was
that we would just keep polling the mailbox even if the device itself had
gone away.
To address the responsiveness issues we can decrease the sleeps to 20ms and
use a jiffies based timeout value rather than just counting the number of
times we slept and then polled.
To address the hardware going away we can move the check for the firmware
BAR being present from where it was and place it inside the loop after the
mailbox descriptor ring is initialized and before we sleep so that we just
abort and return an error if the device went away during initialization.
With these two changes we see a significant improvement in boot times for
the driver.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654721224.499179.2698616208976624755.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There was an issue in that if we were to shutdown we could be left with
a completion in flight as the mailbox went away. To address that I have
added an fbnic_mbx_evict_all_cmpl function that is meant to essentially
create a "broken pipe" type response so that all callers will receive an
error indicating that the connection has been broken as a result of us
shutting down the mailbox.
Fixes: 378e5cc1c6c6 ("eth: fbnic: hwmon: Add completion infrastructure for firmware requests")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654720578.499179.380252598204530873.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The fbnic_mbx_flush_tx function had a number of issues.
First, we were waiting 200ms for the firmware to process the packets. We
can drop this to 20ms and in almost all cases this should be more than
enough time. So by changing this we can significantly reduce shutdown time.
Second, we were not making sure that the Tx path was actually shut off. As
such we could still have packets added while we were flushing the mailbox.
To prevent that we can now clear the ready flag for the Tx side and it
should stay down since the interrupt is disabled.
Third, we kept re-reading the tail due to the second issue. The tail should
not move after we have started the flush so we can just read it once while
we are holding the mailbox Tx lock. By doing that we are guaranteed that
the value should be consistent.
Fourth, we were keeping a count of descriptors cleaned due to the second
and third issues called out. That count is not a valid reason to be exiting
the cleanup, and with the tail only being read once we shouldn't see any
cases where the tail moves after the disable so the tracking of count can
be dropped.
Fifth, we were using attempts * sleep time to determine how long we would
wait in our polling loop to flush out the Tx. This can be very imprecise.
In order to tighten up the timing we are shifting over to using a jiffies
value of jiffies + 10 * HZ + 1 to determine the jiffies value we should
stop polling at as this should be accurate within once sleep cycle for the
total amount of time spent polling.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654719929.499179.16406653096197423749.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We have two issues that need to be addressed in our IRQ handling.
One is the fact that we can end up double-freeing IRQs in the event of an
exception handling error such as a PCIe reset/recovery that fails. To
prevent that from becoming an issue we can use the msix_vector values to
indicate that we have successfully requested/freed the IRQ by only setting
or clearing them when we have completed the given action.
The other issue is that we have several potential races in our IRQ path due
to us manipulating the mask before the vector has been truly disabled. In
order to handle that in the case of the FW mailbox we need to not
auto-enable the IRQ and instead will be enabling/disabling it separately.
In the case of the PCS vector we can mitigate this by unmapping it and
synchronizing the IRQ before we clear the mask.
The general order of operations after this change is now to request the
interrupt, poll the FW mailbox to ready, and then enable the interrupt. For
the shutdown we do the reverse where we disable the interrupt, flush any
pending Tx, and then free the IRQ. I am renaming the enable/disable to
request/free to be equivilent with the IRQ calls being used. We may see
additions in the future to enable/disable the IRQs versus request/free them
for certain use cases.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Fixes: 69684376eed5 ("eth: fbnic: Add link detection")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654719271.499179.3634535105127848325.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In order to prevent the device from throwing spurious writes and/or reads
at us we need to gate the AXI fabric interface to the PCIe until such time
as we know the FW is in a known good state.
To accomplish this we use the mailbox as a mechanism for us to recognize
that the FW has acknowledged our presence and is no longer sending any
stale message data to us.
We start in fbnic_mbx_init by calling fbnic_mbx_reset_desc_ring function,
disabling the DMA in both directions, and then invalidating all the
descriptors in each ring.
We then poll the mailbox in fbnic_mbx_poll_tx_ready and when the interrupt
is set by the FW we pick it up and mark the mailboxes as ready, while also
enabling the DMA.
Once we have completed all the transactions and need to shut down we call
into fbnic_mbx_clean which will in turn call fbnic_mbx_reset_desc_ring for
each ring and shut down the DMA and once again invalidate the descriptors.
Fixes: 3646153161f1 ("eth: fbnic: Add register init to set PCIe/Ethernet device config")
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654718623.499179.7445197308109347982.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Address to issues with the FW mailbox descriptor initialization.
We need to reverse the order of accesses when we invalidate an entry versus
writing an entry. When writing an entry we write upper and then lower as
the lower 32b contain the valid bit that makes the entire address valid.
However for invalidation we should write it in the reverse order so that
the upper is marked invalid before we update it.
Without this change we may see FW attempt to access pages with the upper
32b of the address set to 0 which will likely result in DMAR faults due to
write access failures on mailbox shutdown.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654717972.499179.8083789731819297034.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When a port gets set up, b53 disables learning and enables the port for
flooding. This can undo any bridge configuration on the port.
E.g. the following flow would disable learning on a port:
$ ip link add br0 type bridge
$ ip link set sw1p1 master br0 <- enables learning for sw1p1
$ ip link set br0 up
$ ip link set sw1p1 up <- disables learning again
Fix this by populating dsa_switch_ops::port_setup(), and set up initial
config there.
Fixes: f9b3827ee66c ("net: dsa: b53: Support setting learning on port")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-12-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When VLAN filtering is off, we configure the switch to forward, but not
learn on VLAN table misses. This effectively disables learning while not
filtering.
Fix this by switching to forward and learn. Setting the learning disable
register will still control whether learning actually happens.
Fixes: dad8d7c6452b ("net: dsa: b53: Properly account for VLAN filtering")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-11-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To allow runtime switching between vlan aware and vlan non-aware mode,
we need to properly keep track of any bridge VLAN configuration.
Likewise, we need to know when we actually switch between both modes, to
not have to rewrite the full VLAN table every time we update the VLANs.
So keep track of the current vlan_filtering mode, and on changes, apply
the appropriate VLAN configuration.
Fixes: 0ee2af4ebbe3 ("net: dsa: set configure_vlan_while_not_filtering to true by default")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-10-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Documentation/networking/switchdev.rst says:
- with VLAN filtering turned off: the bridge is strictly VLAN unaware and its
data path will process all Ethernet frames as if they are VLAN-untagged.
The bridge VLAN database can still be modified, but the modifications should
have no effect while VLAN filtering is turned off.
This breaks if we immediately apply the VLAN configuration, so skip
writing it when vlan_filtering is off.
Fixes: 0ee2af4ebbe3 ("net: dsa: set configure_vlan_while_not_filtering to true by default")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-9-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since we cannot set forwarding destinations per VLAN, we should not have
a VLAN 0 configured, as it would allow untagged traffic to work across
ports on VLAN aware bridges regardless if a PVID untagged VLAN exists.
So remove the VLAN 0 on join, an re-add it on leave. But only do so if
we have a VLAN aware bridge, as without it, untagged traffic would
become tagged with VID 0 on a VLAN unaware bridge.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-8-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While JOIN_ALL_VLAN allows to join all VLANs, we still need to keep the
default VLAN enabled so that untagged traffic stays untagged.
So rejoin the default VLAN even for switches with JOIN_ALL_VLAN support.
Fixes: 48aea33a77ab ("net: dsa: b53: Add JOIN_ALL_VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-7-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The untagged default VLAN is added to the default vlan, which may be
one, but we modify the VLAN 0 entry on bridge leave.
Fix this to use the correct VLAN entry for the default pvid.
Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-6-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Presumably the intention here was to flush the VLAN of the old pvid, not
the added VLAN again, which we already flushed before.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-5-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the PVID of ports are only set when adding/updating VLANs with
PVID set or removing VLANs, but not when clearing the PVID flag of a
VLAN.
E.g. the following flow
$ ip link add br0 type bridge vlan_filtering 1
$ ip link set sw1p1 master bridge
$ bridge vlan add dev sw1p1 vid 10 pvid untagged
$ bridge vlan add dev sw1p1 vid 10 untagged
Would keep the PVID set as 10, despite the flag being cleared. Fix this
by checking if we need to unset the PVID on vlan updates.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-4-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Broadcom management header does not carry the original VLAN tag
state information, just the ingress port, so for untagged frames we do
not know from which VLAN they originated.
Therefore keep the CPU port always tagged except for VLAN 0.
Fixes the following setup:
$ ip link add br0 type bridge vlan_filtering 1
$ ip link set sw1p1 master br0
$ bridge vlan add dev br0 pvid untagged self
$ ip link add sw1p2.10 link sw1p2 type vlan id 10
Where VID 10 would stay untagged on the CPU port.
Fixes: 2c32a3d3c233 ("net: dsa: b53: Do not force CPU to be always tagged")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-3-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow reserved multicast to ignore VLAN membership so STP and other
management protocols work without a PVID VLAN configured when using a
vlan aware bridge.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-2-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When sending out any kind of traffic, it is essential that the driver
keeps reporting BQL of the number of bytes that have been sent so that
BQL can track the amount of data in the queue and prevents it from
overflowing. If BQL is not reported, the driver may continue sending
packets even when the queue is full, leading to packet loss, congestion
and decreased network performance. Currently this is missing in
emac_xmit_xdp_frame() and this patch fixes it.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250506110546.4065715-4-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add __netif_tx_lock() to ensure that only one packet is being
transmitted at a time to avoid race conditions in the netif_txq
struct and prevent packet data corruption. Failing to do so causes
kernel panic with the following error:
[ 2184.746764] ------------[ cut here ]------------
[ 2184.751412] kernel BUG at lib/dynamic_queue_limits.c:99!
[ 2184.756728] Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
logs: https://gist.github.com/MeghanaMalladiTI/9c7aa5fc3b7fb03f87c74aad487956e9
The lock is acquired before calling emac_xmit_xdp_frame() and released after the
call returns. This ensures that the TX queue is protected from concurrent access
during the transmission of XDP frames.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250506110546.4065715-3-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xdp_features demonstrates what all XDP capabilities are supported
on a given network device. The driver needs to set these xdp_features
flag to let the network stack know what XDP features a given driver
is supporting. These flags need to be set for a given ndev irrespective
of any XDP program being loaded or not.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250506110546.4065715-2-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The official Airoha EN7581 firmware requires adding max_packet field in
ppe_mbox_data struct while the unofficial one used to develop the Airoha
EN7581 flowtable support does not require this field.
This patch does not introduce any real backwards compatible issue since
EN7581 fw is not publicly available in linux-firmware or other
repositories (e.g. OpenWrt) yet and the official fw version will use this
new layout. For this reason this change needs to be backported.
Moreover, make explicit the padding added by the compiler introducing
the rsv array in init_info struct.
At the same time use u32 instead of int for init_info and set_info
struct definitions in ppe_mbox_data struct.
Fixes: 23290c7bc190d ("net: airoha: Introduce Airoha NPU support")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250506-airoha-en7581-fix-ppe_mbox_data-v5-1-29cabed6864d@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Couple of fixes:
* iwlwifi: add two missing device entries
* cfg80211: fix a potential out-of-bounds access
* mac80211: fix format of TID to link mapping action frames
* tag 'wireless-2025-05-06' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: iwlwifi: add support for Killer on MTL
wifi: mac80211: fix the type of status_code for negotiated TID to Link Mapping
wifi: cfg80211: fix out-of-bounds access during multi-link element defragmentation
====================
Link: https://patch.msgid.link/20250506203506.158818-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2025-05-06
The first patch is by Antonios Salios and adds a missing
spin_lock_init() to the m_can driver.
The next 3 patches are by me and fix the unregistration order in the
mcp251xfd, rockchip_canfd and m_can driver.
The last patch is by Oliver Hartkopp and fixes RCU and BH
locking/handling in the CAN gw protocol.
* tag 'linux-can-fixes-for-6.15-20250506' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: gw: fix RCU/BH usage in cgw_create_job()
can: mcan: m_can_class_unregister(): fix order of unregistration calls
can: rockchip_canfd: rkcanfd_remove(): fix order of unregistration calls
can: mcp251xfd: mcp251xfd_remove(): fix order of unregistration calls
can: mcp251xfd: fix TDC setting for low data bit rates
can: m_can: m_can_class_allocate_dev(): initialize spin lock on device probe
====================
Link: https://patch.msgid.link/20250506135939.652543-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use Device Serial Number instead of PCI bus/device/function for
the index of struct ice_adapter.
Functions on the same physical device should point to the very same
ice_adapter instance, but with two PFs, when at least one of them is
PCI-e passed-through to a VM, it is no longer the case - PFs will get
seemingly random PCI BDF values, and thus indices, what finally leds to
each of them being on their own instance of ice_adapter. That causes them
to don't attempt any synchronization of the PTP HW clock usage, or any
other future resources.
DSN works nicely in place of the index, as it is "immutable" in terms of
virtualization.
Fixes: 0e2bddf9e5f9 ("ice: add ice_adapter for shared data across PFs on the same NIC")
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250505161939.2083581-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For now, we need another entry for these devices, this
will be changed completely for 6.16.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219926
Link: https://patch.msgid.link/20250506214258.2efbdc9e9a82.I31915ec252bd1c74bd53b89a0e214e42a74b6f2e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 1be37d3b0414 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-3-59a9b131589d@pengutronix.de
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: ff60bfbaf67f ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-2-59a9b131589d@pengutronix.de
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
With the mcp251xfd driver the removal of the module causes the
following warning:
| WARNING: CPU: 0 PID: 352 at net/core/dev.c:7342 __netif_napi_del_locked+0xc8/0xd8
as can_rx_offload_del() deletes the NAPI, while it is still active,
because the interface is still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-1-59a9b131589d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The TDC is currently hardcoded enabled. This means that even for lower
CAN-FD data bitrates (with a DBRP (data bitrate prescaler) > 2) a TDC
is configured. This leads to a bus-off condition.
ISO 11898-1 section 11.3.3 says "Transmitter delay compensation" (TDC)
is only applicable if DBRP is 1 or 2.
To fix the problem, switch the driver to use the TDC calculation
provided by the CAN driver framework (which respects ISO 11898-1
section 11.3.3). This has the positive side effect that userspace can
control TDC as needed.
Demonstration of the feature in action:
| $ ip link set can0 up type can bitrate 125000 dbitrate 500000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 125000 sample-point 0.875
| tq 50 prop-seg 69 phase-seg1 70 phase-seg2 20 sjw 10 brp 2
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 500000 dsample-point 0.875
| dtq 125 dprop-seg 6 dphase-seg1 7 dphase-seg2 2 dsjw 1 dbrp 5
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
| $ ip link set can0 up type can bitrate 1000000 dbitrate 4000000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD,TDC-AUTO> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 1000000 sample-point 0.750
| tq 25 prop-seg 14 phase-seg1 15 phase-seg2 10 sjw 5 brp 1
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 4000000 dsample-point 0.700
| dtq 25 dprop-seg 3 dphase-seg1 3 dphase-seg2 3 dsjw 1 dbrp 1
| tdco 7
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
There has been some confusion about the MCP2518FD using a relative or
absolute TDCO due to the datasheet specifying a range of [-64,63]. I
have a custom board with a 40 MHz clock and an estimated loop delay of
100 to 216 ns. During testing at a data bit rate of 4 Mbit/s I found
that using can_get_relative_tdco() resulted in bus-off errors. The
final TDCO value was 1 which corresponds to a 10% SSP in an absolute
configuration. This behavior is expected if the TDCO value is really
absolute and not relative. Using priv->can.tdc.tdco instead results in
a final TDCO of 8, setting the SSP at exactly 80%. This configuration
works.
The automatic, manual, and off TDC modes were tested at speeds up to,
and including, 8 Mbit/s on real hardware and behave as expected.
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reported-by: Kelsey Maes <kelsey@vpprocess.com>
Closes: https://lore.kernel.org/all/C2121586-C87F-4B23-A933-845362C29CA1@vpprocess.com
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Kelsey Maes <kelsey@vpprocess.com>
Link: https://patch.msgid.link/20250430161501.79370-1-kelsey@vpprocess.com
[mkl: add comment]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The spin lock tx_handling_spinlock in struct m_can_classdev is not
being initialized. This leads the following spinlock bad magic
complaint from the kernel, eg. when trying to send CAN frames with
cansend from can-utils:
| BUG: spinlock bad magic on CPU#0, cansend/95
| lock: 0xff60000002ec1010, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
| CPU: 0 UID: 0 PID: 95 Comm: cansend Not tainted 6.15.0-rc3-00032-ga79be02bba5c #5 NONE
| Hardware name: MachineWare SIM-V (DT)
| Call Trace:
| [<ffffffff800133e0>] dump_backtrace+0x1c/0x24
| [<ffffffff800022f2>] show_stack+0x28/0x34
| [<ffffffff8000de3e>] dump_stack_lvl+0x4a/0x68
| [<ffffffff8000de70>] dump_stack+0x14/0x1c
| [<ffffffff80003134>] spin_dump+0x62/0x6e
| [<ffffffff800883ba>] do_raw_spin_lock+0xd0/0x142
| [<ffffffff807a6fcc>] _raw_spin_lock_irqsave+0x20/0x2c
| [<ffffffff80536dba>] m_can_start_xmit+0x90/0x34a
| [<ffffffff806148b0>] dev_hard_start_xmit+0xa6/0xee
| [<ffffffff8065b730>] sch_direct_xmit+0x114/0x292
| [<ffffffff80614e2a>] __dev_queue_xmit+0x3b0/0xaa8
| [<ffffffff8073b8fa>] can_send+0xc6/0x242
| [<ffffffff8073d1c0>] raw_sendmsg+0x1a8/0x36c
| [<ffffffff805ebf06>] sock_write_iter+0x9a/0xee
| [<ffffffff801d06ea>] vfs_write+0x184/0x3a6
| [<ffffffff801d0a88>] ksys_write+0xa0/0xc0
| [<ffffffff801d0abc>] __riscv_sys_write+0x14/0x1c
| [<ffffffff8079ebf8>] do_trap_ecall_u+0x168/0x212
| [<ffffffff807a830a>] handle_exception+0x146/0x152
Initializing the spin lock in m_can_class_allocate_dev solves that
problem.
Fixes: 1fa80e23c150 ("can: m_can: Introduce a tx_fifo_in_flight counter")
Signed-off-by: Antonios Salios <antonios@mwa.re>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250425111744.37604-2-antonios@mwa.re
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Remove redundant PSE reset.
When setting FE register there is no need to reset PSE,
doing so may cause FE to work abnormal.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/3a5223473e086a4b54a2b9a44df7d9ddcc2bc75a
Fixes: dee4dd10c79aa ("net: ethernet: mtk_eth_soc: ppe: add support for multiple PPEs")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://patch.msgid.link/18f0ac7d83f82defa3342c11ef0d1362f6b81e88.1746406763.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The purpose of resetting the TX queue is to reset the byte and packet
count as well as to clear the software flow control XOFF bit.
MediaTek developers pointed out that netdev_reset_queue would only
resets queue 0 of the network device.
Queues that are not reset may cause unexpected issues.
Packets may stop being sent after reset and "transmit timeout" log may
be displayed.
Import fix from MediaTek's SDK to resolve this issue.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/319c0d9905579a46dc448579f892f364f1f84818
Fixes: f63959c7eec31 ("net: ethernet: mtk_eth_soc: implement multi-queue support for per-port queues")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/c9ff9adceac4f152239a0f65c397f13547639175.1746406763.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The selftests added to our CI by Bui Quang Minh recently reveals
that there is a mem leak on the error path of virtnet_xsk_pool_enable():
unreferenced object 0xffff88800a68a000 (size 2048):
comm "xdp_helper", pid 318, jiffies 4294692778
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 0):
__kvmalloc_node_noprof+0x402/0x570
virtnet_xsk_pool_enable+0x293/0x6a0 (drivers/net/virtio_net.c:5882)
xp_assign_dev+0x369/0x670 (net/xdp/xsk_buff_pool.c:226)
xsk_bind+0x6a5/0x1ae0
__sys_bind+0x15e/0x230
__x64_sys_bind+0x72/0xb0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Acked-by: Jason Wang <jasowang@redhat.com>
Fixes: e9f3962441c0 ("virtio_net: xsk: rx: support fill with xsk buffer")
Link: https://patch.msgid.link/20250430163836.3029761-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 4bc12818b363 ("virtio-net: disable delayed refill when pausing rx")
fixed a deadlock between reconfig paths and refill work trying to disable
the same NAPI instance. The refill work can't run in parallel with reconfig
because trying to double-disable a NAPI instance causes a stall under the
instance lock, which the reconfig path needs to re-enable the NAPI and
therefore unblock the stalled thread.
There are two cases where we re-enable refill too early. One is in the
virtnet_set_queues() handler. We call it when installing XDP:
virtnet_rx_pause_all(vi);
...
virtnet_napi_tx_disable(..);
...
virtnet_set_queues(..);
...
virtnet_rx_resume_all(..);
We want the work to be disabled until we call virtnet_rx_resume_all(),
but virtnet_set_queues() kicks it before NAPIs were re-enabled.
The other case is a more trivial case of mis-ordering in
__virtnet_rx_resume() found by code inspection.
Taking the spin lock in virtnet_set_queues() (requested during review)
may be unnecessary as we are under rtnl_lock and so are all paths writing
to ->refill_enabled.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Bui Quang Minh <minhquangbui99@gmail.com>
Fixes: 4bc12818b363 ("virtio-net: disable delayed refill when pausing rx")
Fixes: 413f0271f396 ("net: protect NAPI enablement with netdev_lock()")
Link: https://patch.msgid.link/20250430163758.3029367-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case the CMD_RTS got corrupted by interferences, the MSE102x
doesn't allow a retransmission of the command. Instead the Ethernet
frame must be shifted out of the SPI FIFO. Since the actual length is
unknown, assume the maximum possible value.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-5-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since there is no protection in the SPI protocol against electrical
interferences, the driver shouldn't blindly trust the length payload
of CMD_RTS. So introduce a bounds check for incoming frames.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-4-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The LEN_MASK for CMD_RTS doesn't cover the whole parameter mask.
The Bit 11 is reserved, so adjust LEN_MASK accordingly.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MSE102x doesn't provide any SPI commands for interrupt handling.
So in case the interrupt fired before the driver requests the IRQ,
the interrupt will never fire again. In order to fix this always poll
for pending packets after opening the interface.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the ptp_clock_register() is called before relative
ptp resource ready. It may cause unexpected result when upper
layer called the ptp API during the timewindow. Fix it by
moving the ptp_clock_register() to the function end.
Fixes: 0bf5eb788512 ("net: hns3: add support for PTP")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250430093052.2400464-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The size of the tm_qset file of debugfs is limited to 64 KB,
which is too small in the scenario with 1280 qsets.
The size needs to be expanded to 1 MB.
Fixes: 5e69ea7ee2a6 ("net: hns3: refactor the debugfs process")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250430093052.2400464-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a VF is passthrough to a VM, and the VM is killed, the reported
interrupt may not been handled, it will remain, and won't be clear by
the nic engine even with a flr or tqp reset. When the VM restart, the
interrupt of the first vector may be dropped by the second enable_irq
in vfio, see the issue below:
https://gitlab.com/qemu-project/qemu/-/issues/2884#note_2423361621
We notice that the vfio has always behaved this way, and the interrupt
is a residue of the nic engine, so we fix the problem by moving the
vector enable process out of the enable_irq loop.
Fixes: 08a100689d4b ("net: hns3: re-organize vector handle")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250430093052.2400464-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VF driver missed to store the rx VLAN tag strip state when
user change the rx VLAN tag offload state. And it will default
to enable the rx vlan tag strip when re-init VF device after
reset. So if user disable rx VLAN tag offload, and trig reset,
then the HW will still strip the VLAN tag from packet nad fill
into RX BD, but the VF driver will ignore it for rx VLAN tag
offload disabled. It may cause the rx VLAN tag dropped.
Fixes: b2641e2ad456 ("net: hns3: Add support of hardware rx-vlan-offload to HNS3 VF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250430093052.2400464-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-04-29 (idpf, igc)
For idpf:
Michal fixes error path handling to remove memory leak.
Larysa prevents reset from being called during shutdown.
For igc:
Jake adjusts locking order to resolve sleeping in atomic context.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: fix lock order in igc_ptp_reset
idpf: protect shutdown from reset
idpf: fix potential memory leak on kcalloc() failure
====================
Link: https://patch.msgid.link/20250429221034.3909139-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the host loses heartbeat messages from the device,
the driver calls the device-specific ndo_stop function,
which frees the resources. If the driver is unloaded in
this scenario, it calls ndo_stop again, attempting to free
resources that have already been freed, leading to a host
hang issue. To resolve this, dev_close should be called
instead of the device-specific stop function.dev_close
internally calls ndo_stop to stop the network interface
and performs additional cleanup tasks. During the driver
unload process, if the device is already down, ndo_stop
is not called.
Fixes: 5cb96c29aa0e ("octeon_ep: add heartbeat monitor")
Signed-off-by: Sathesh B Edara <sedara@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250429114624.19104-1-sedara@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Activate TX hang workaround also in
fec_enet_txq_submit_skb() when TSO is not enabled.
Errata: ERR007885
Symptoms: NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
commit 37d6017b84f7 ("net: fec: Workaround for imx6sx enet tx hang when enable three queues")
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
Fixes: 53bb20d1faba ("net: fec: add variable reg_desc_active to speed things up")
Signed-off-by: Mattias Barthel <mattias.barthel@atlascopco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250429090826.3101258-1-mattiasbarthel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Always map the `skb` to the LS descriptor. Previously skb was
mapped to EXT descriptor when the number of fragments is zero with
GSO enabled. Mapping the skb to EXT descriptor prevents it from
being freed, leading to a memory leak
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250429052527.10031-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Recent updates to the PTP part of bnxt changed the way PTP FIFO is
cleared, skbs waiting for TX timestamps are now cleared during
ndo_close() call. To do clearing procedure, the ptp structure must
exist and point to a valid address. Module destroy sequence had ptp
clear code running before netdev close causing invalid memory access and
kernel crash. Change the sequence to destroy ptp structure after device
close.
Fixes: 8f7ae5a85137 ("bnxt_en: improve TX timestamping FIFO configuration")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Closes: https://lore.kernel.org/netdev/CAMArcTWDe2cd41=ub=zzvYifaYcYv-N-csxfqxUvejy_L0D6UQ@mail.gmail.com/
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250430170343.759126-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
