| Age | Commit message (Collapse) | Author |
|---|
|
Fix _ctl_get_mpt_mctp_passthru_adapter() to return the correct IOC
pointer to caller based on dev_index.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Link: https://lore.kernel.org/r/1747213781-31545-1-git-send-email-shivasharan.srikanteshwara@broadcom.com
Fixes: c72be4b5bb7c ("scsi: mpt3sas: Add support for MCTP Passthrough commands")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (scsi_debug, ufs, lpfc, st, fnic, mpi3mr,
mpt3sas) and the removal of cxlflash.
The only non-trivial core change is an addition to unit attention
handling to recognize UAs for power on/reset and new media so the tape
driver can use it"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (107 commits)
scsi: st: Tighten the page format heuristics with MODE SELECT
scsi: st: ERASE does not change tape location
scsi: st: Fix array overflow in st_setup()
scsi: target: tcm_loop: Fix wrong abort tag
scsi: lpfc: Restore clearing of NLP_UNREG_INP in ndlp->nlp_flag
scsi: hisi_sas: Fixed failure to issue vendor specific commands
scsi: fnic: Remove unnecessary NUL-terminations
scsi: fnic: Remove redundant flush_workqueue() calls
scsi: core: Use a switch statement when attaching VPD pages
scsi: ufs: renesas: Add initialization code for R-Car S4-8 ES1.2
scsi: ufs: renesas: Add reusable functions
scsi: ufs: renesas: Refactor 0x10ad/0x10af PHY settings
scsi: ufs: renesas: Remove register control helper function
scsi: ufs: renesas: Add register read to remove save/set/restore
scsi: ufs: renesas: Replace init data by init code
scsi: ufs: dt-bindings: renesas,ufs: Add calibration data
scsi: mpi3mr: Task Abort EH Support
scsi: storvsc: Don't report the host packet status as the hv status
scsi: isci: Make most module parameters static
scsi: megaraid_sas: Make most module parameters static
...
|
|
The "sz" argument in mpt3sas_check_cmd_timeout() is the number of u32, not
the number of bytes. We dump that many u32 values to dmesg. Passing the
number of bytes will lead to a read overflow. Divide by 4 to get the
correct value.
Fixes: c72be4b5bb7c ("scsi: mpt3sas: Add support for MCTP Passthrough commands")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/02b0d4ff-961c-49ae-921a-5cc469edf93c@stanley.mountain
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation for memtostr*() checking that its source is marked as
nonstring, annotate the device strings accordingly.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> # SCSI
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
There is a spelling mistake in a ioc_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20250221083253.77496-1-colin.i.king@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Shivasharan S <shivasharan.srikanteshwara@broadcom.com> says:
This patch series adds support for the MCTP passthrough function over
the MPI interface for management commands. Also fix issue related to
task management handling during IOCTL timeout.
Link: https://lore.kernel.org/r/1739410016-27503-1-git-send-email-shivasharan.srikanteshwara@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Link: https://lore.kernel.org/r/1739410016-27503-6-git-send-email-shivasharan.srikanteshwara@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When an IOCTL times out and driver issues a target reset, if firmware
fails the task management elevate the recovery by issuing a diag reset to
controller.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Link: https://lore.kernel.org/r/1739410016-27503-5-git-send-email-shivasharan.srikanteshwara@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add a new capability field to report the MCTP passthrough support to
applications.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Link: https://lore.kernel.org/r/1739410016-27503-4-git-send-email-shivasharan.srikanteshwara@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The MPI specification defines support for sending MCTP management commands
as a passthrough function to the IOC. Add support for driver to discover
the IOC capability to support MCTP passthrough function. Driver will
support applications and kernel modules to send MPT commands containing the
MCTP passthrough request to firmware through an MPI request.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/1739410016-27503-3-git-send-email-shivasharan.srikanteshwara@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Updated MPI header files to version 02.00.62.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Link: https://lore.kernel.org/r/1739410016-27503-2-git-send-email-shivasharan.srikanteshwara@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Call mutex_unlock(&ioc->hostdiag_unlock_mutex) once from error paths
instead of twice.
This patch fixes the following Clang -Wthread-safety errors:
drivers/scsi/mpt3sas/mpt3sas_base.c:8085:2: error: mutex 'ioc->hostdiag_unlock_mutex' is not held on every path through here [-Werror,-Wthread-safety-analysis]
8085 | pci_cfg_access_unlock(ioc->pdev);
| ^
drivers/scsi/mpt3sas/mpt3sas_base.c:8019:2: note: mutex acquired here
8019 | mutex_lock(&ioc->hostdiag_unlock_mutex);
| ^
./include/linux/mutex.h:171:26: note: expanded from macro 'mutex_lock'
171 | #define mutex_lock(lock) mutex_lock_nested(lock, 0)
| ^
drivers/scsi/mpt3sas/mpt3sas_base.c:8085:2: error: mutex 'ioc->hostdiag_unlock_mutex' is not held on every path through here [-Werror,-Wthread-safety-analysis]
8085 | pci_cfg_access_unlock(ioc->pdev);
| ^
drivers/scsi/mpt3sas/mpt3sas_base.c:8019:2: note: mutex acquired here
8019 | mutex_lock(&ioc->hostdiag_unlock_mutex);
| ^
./include/linux/mutex.h:171:26: note: expanded from macro 'mutex_lock'
171 | #define mutex_lock(lock) mutex_lock_nested(lock, 0)
| ^
drivers/scsi/mpt3sas/mpt3sas_base.c:8087:2: error: releasing mutex 'ioc->hostdiag_unlock_mutex' that was not held [-Werror,-Wthread-safety-analysis]
8087 | mutex_unlock(&ioc->hostdiag_unlock_mutex);
| ^
Cc: Ranjan Kumar <ranjan.kumar@broadcom.com>
Fixes: c0767560b012 ("scsi: mpt3sas: Reload SBR without rebooting HBA")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20250210203936.2946494-3-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On several systems with Dell HBA controller Linux prints the warning below:
$ dmesg | grep -e "Linux version" -e "DMI: Dell" -e "ignore_delay_remove"
[ 0.000000] Linux version 6.12.11.mx64.479 (root@lucy.molgen.mpg.de) (gcc (GCC) 12.3.0, GNU ld (GNU Binutils) 2.41) #1 SMP PREEMPT_DYNAMIC Fri Jan 24 13:30:47 CET 2025
[ 0.000000] DMI: Dell Inc. PowerEdge R7625/0M7YXP, BIOS 1.10.6 12/06/2024
[ 9.386551] scsi 0:0:4:0: set ignore_delay_remove for handle(0x0012)
A user does not know, what to do about it, and everything seems to work as
expected. Therefore, remove the log level from warning to info.
Device information:
$ dmesg | grep -e 0:4:0 -e '12)'
[ 8.857606] mpt3sas_cm0: config page(0x00000000db0e4179) - dma(0xfd5f6000): size(512)
[ 9.133856] scsi 0:0:0:0: SATA: handle(0x0017), sas_addr(0x3c0470e0d40cc20c), phy(12), device_name(0x5000039db8d2284b)
[ 9.366341] mpt3sas_cm0: handle(0x12) sas_address(0x3c0570e0d40cc208) port_type(0x0)
[ 9.378867] scsi 0:0:4:0: Enclosure DP BP_PSV 7.10 PQ: 0 ANSI: 7
[ 9.386551] scsi 0:0:4:0: set ignore_delay_remove for handle(0x0012)
[ 9.387465] scsi 0:0:4:0: SES: handle(0x0012), sas_addr(0x3c0570e0d40cc208), phy(17), device_name(0x3c0570e0d40cc208)
[ 9.387465] scsi 0:0:4:0: enclosure logical id (0x3c0470e0d4092108), slot(8)
[ 9.387465] scsi 0:0:4:0: enclosure level(0x0001), connector name( C0 )
[ 9.390495] scsi 0:0:4:0: qdepth(1), tagged(0), scsi_level(8), cmd_que(0)
[ 9.401700] end_device-0:4: add: handle(0x0012), sas_addr(0x3c0570e0d40cc208)
[ 9.471916] ses 0:0:4:0: Attached Enclosure device
[ 9.480088] ses 0:0:4:0: Attached scsi generic sg4 type 13
$ lspci -nn -k -s 41:
41:00.0 Serial Attached SCSI controller [0107]: Broadcom / LSI Fusion-MPT 12GSAS/PCIe Secure SAS38xx [1000:00e6]
DeviceName: SL3 NonRAID
Subsystem: Dell HBA355i Front [1028:200c]
Kernel driver in use: mpt3sas
Fixes: 30158dc9bbc9 ("mpt3sas: Never block the Enclosure device")
Cc: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20250131171640.30721-1-pmenzel@molgen.mpg.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
mpt3sas_config_get_manufacturing_pg7() and
mpt3sas_config_get_sas_device_pg1() were added as part of 2012's
commit f92363d12359 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
but haven't been used.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20250127002851.113711-1-linux@treblig.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
'struct pci_error_handlers' are not modified in these drivers.
Constifying these structures moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
39049 6429 112 45590 b216 drivers/scsi/aacraid/linit.o
After:
=====
text data bss dec hex filename
39113 6365 112 45590 b216 drivers/scsi/aacraid/linit.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/efdec8425981e10fc398fa2ac599c9c45d930561.1737318548.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, fnic, qla2xx, mpi3mr).
The major core change is the renaming of the slave_ methods plus a bit
of constification. The rest are minor updates and fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (103 commits)
scsi: fnic: Propagate SCSI error code from fnic_scsi_drv_init()
scsi: fnic: Test for memory allocation failure and return error code
scsi: fnic: Return appropriate error code from failure of scsi drv init
scsi: fnic: Return appropriate error code for mem alloc failure
scsi: fnic: Remove always-true IS_FNIC_FCP_INITIATOR macro
scsi: fnic: Fix use of uninitialized value in debug message
scsi: fnic: Delete incorrect debugfs error handling
scsi: fnic: Remove unnecessary else to fix warning in FDLS FIP
scsi: fnic: Remove extern definition from .c files
scsi: fnic: Remove unnecessary else and unnecessary break in FDLS
scsi: mpi3mr: Fix possible crash when setting up bsg fails
scsi: ufs: bsg: Set bsg_queue to NULL after removal
scsi: ufs: bsg: Delete bsg_dev when setting up bsg fails
scsi: st: Don't set pos_unknown just after device recognition
scsi: aic7xxx: Fix build 'aicasm' warning
scsi: Revert "scsi: ufs: core: Probe for EXT_IID support"
scsi: storvsc: Ratelimit warning logs to prevent VM denial of service
scsi: scsi_debug: Constify sdebug_driver_template
scsi: documentation: Corrections for struct updates
scsi: driver-api: documentation: Change what is added to docbook
...
|
|
Pull in fixes branch to resolve merge conflict in ufs-qcom.c.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, the code does:
if (x == 0) {
x &= ~0x3;
x |= 0x1;
}
Zeroing bits 0 and 1 of a variable that is 0 is not necessary. So directly
set the variable to 1.
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Fixes: f92363d12359 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20241212221817.78940-2-pmenzel@molgen.mpg.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Linux 5.15 logs the error below
mpt3sas_cm0: overriding NVDATA EEDPTagMode setting
on a Dell PowerEdge T440 with the card below.
5e:00.0 Serial Attached SCSI controller [0107]: Broadcom / LSI SAS3008 PCI-Express Fusion-MPT SAS-3 [1000:0097] (rev 02)
It’s not clear to a user what this error is about. As a first step to
improve this, add the values to the error message.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20241212221817.78940-1-pmenzel@molgen.mpg.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replace all users of blk_mq_pci_map_queues with the more generic
blk_mq_map_hw_queues. This in preparation to retire
blk_mq_pci_map_queues.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Link: https://lore.kernel.org/r/20241202-refactor-blk-affinity-helpers-v6-5-27211e9c2cd5@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Improve naming consistency with the .sdev_prep() and .sdev_destroy()
methods by renaming .device_configure() into .sdev_configure().
Cc: Christoph Hellwig <hch@lst.de>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-3-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Rename .slave_alloc() into .sdev_init() and .slave_destroy() into
.sdev_destroy(). The new names make it clear that these are actions on
SCSI devices. Make this change in the SCSI core, SCSI drivers and also
in the ATA drivers. No functionality has been changed.
This patch has been created as follows:
* Change the text "slave_alloc" into "sdev_init" in all source files
except those in drivers/net/ and Documentation/.
* Change the text "slave_destroy" into "sdev_destroy" in all source
files except those in drivers/net/ and Documentation/.
* Rename lpfc_no_slave() into lpfc_no_sdev().
* Manually adjust whitespace where necessary to restore vertical
alignment (dc395x driver and include/linux/libata.h).
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update driver version to 51.100.00.00.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110173341.11595-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
time
Issue a Diag-Reset when the "Doorbell-In-Use" bit is set during the
driver load/initialization.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110173341.11595-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
Pull more SCSI updates from James Bottomley:
"These are mostly minor updates.
There are two drivers (lpfc and mpi3mr) which missed the initial
pull and a core change to retry a start/stop unit which affect
suspend/resume"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi: lpfc: Update lpfc version to 14.4.0.5
scsi: lpfc: Support loopback tests with VMID enabled
scsi: lpfc: Revise TRACE_EVENT log flag severities from KERN_ERR to KERN_WARNING
scsi: lpfc: Ensure DA_ID handling completion before deleting an NPIV instance
scsi: lpfc: Fix kref imbalance on fabric ndlps from dev_loss_tmo handler
scsi: lpfc: Restrict support for 32 byte CDBs to specific HBAs
scsi: lpfc: Update phba link state conditional before sending CMF_SYNC_WQE
scsi: lpfc: Add ELS_RSP cmd to the list of WQEs to flush in lpfc_els_flush_cmd()
scsi: mpi3mr: Update driver version to 8.12.0.0.50
scsi: mpi3mr: Improve wait logic while controller transitions to READY state
scsi: mpi3mr: Update MPI Headers to revision 34
scsi: mpi3mr: Use firmware-provided timestamp update interval
scsi: mpi3mr: Enhance the Enable Controller retry logic
scsi: sd: Fix off-by-one error in sd_read_block_characteristics()
scsi: pm8001: Do not overwrite PCI queue mapping
scsi: scsi_debug: Remove a useless memset()
scsi: pmcraid: Convert comma to semicolon
scsi: sd: Retry START STOP UNIT commands
scsi: mpi3mr: A performance fix
scsi: ufs: qcom: Update MODE_MAX cfg_bw value
...
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, smartpqi, NCR5380, mac_scsi, lpfc,
mpi3mr).
There are no user visible core changes and a whole series of minor
updates and fixes. The largest core change is probably the
simplification of the workqueue allocation path"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (86 commits)
scsi: smartpqi: update driver version to 2.1.30-031
scsi: smartpqi: fix volume size updates
scsi: smartpqi: fix rare system hang during LUN reset
scsi: smartpqi: add new controller PCI IDs
scsi: smartpqi: add counter for parity write stream requests
scsi: smartpqi: correct stream detection
scsi: smartpqi: Add fw log to kdump
scsi: bnx2fc: Remove some unused fields in struct bnx2fc_rport
scsi: qla2xxx: Remove the unused 'del_list_entry' field in struct fc_port
scsi: ufs: core: Remove ufshcd_urgent_bkops()
scsi: core: Remove obsoleted declaration for scsi_driverbyte_string()
scsi: bnx2i: Remove unused declarations
scsi: core: Simplify an alloc_workqueue() invocation
scsi: ufs: Simplify alloc*_workqueue() invocation
scsi: stex: Simplify an alloc_ordered_workqueue() invocation
scsi: scsi_transport_fc: Simplify alloc_workqueue() invocations
scsi: snic: Simplify alloc_workqueue() invocations
scsi: qedi: Simplify an alloc_workqueue() invocation
scsi: qedf: Simplify alloc_workqueue() invocations
scsi: myrs: Simplify an alloc_ordered_workqueue() invocation
...
|
|
There is a extraneous space after a newline in an ioc_info message.
Remove it and join to split literal strings into one.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240902172708.369741-1-colin.i.king@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Let alloc_ordered_workqueue() format the workqueue name instead of calling
snprintf() explicitly.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240822195944.654691-10-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The workqueue maintainer wants to remove the create*_workqueue() macros
because these macros always set the WQ_MEM_RECLAIM flag and because these
only support literal workqueue names. Hence this patch that replaces the
create*_workqueue() invocations with the definition of this macro. The
WQ_MEM_RECLAIM flag has been retained because I think that flag is necessary
for workqueues created by storage drivers. This patch has been generated by
running spatch and git clang-format. spatch has been invoked as follows:
spatch --in-place --sp-file expand-create-workqueue.spatch $(git grep -lEw 'create_(freezable_|singlethread_|)workqueue' */scsi */ufs)
The contents of the expand-create-workqueue.spatch file is as follows:
@@
expression name;
@@
-create_workqueue(name)
+alloc_workqueue("%s", WQ_MEM_RECLAIM, 1, name)
@@
expression name;
@@
-create_freezable_workqueue(name)
+alloc_workqueue("%s", WQ_FREEZABLE | WQ_UNBOUND | WQ_MEM_RECLAIM, 1, name)
@@
expression name;
@@
-create_singlethread_workqueue(name)
+alloc_ordered_workqueue("%s", WQ_MEM_RECLAIM, name)
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240822195944.654691-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull outstanding commits from 6.11 queue into fixes.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Some firmware versions of the 9600 series SAS HBA byte-swap the REPORT
ZONES command reply buffer from ATA-ZAC devices by directly accessing the
buffer in the host memory. This does not respect the default command DMA
direction and causes IOMMU page faults on architectures with an IOMMU
enforcing write-only mappings for DMA_FROM_DEVICE DMA driection (e.g. AMD
hosts).
scsi 18:0:0:0: Direct-Access-ZBC ATA WDC WSH722020AL W870 PQ: 0 ANSI: 6
scsi 18:0:0:0: SATA: handle(0x0027), sas_addr(0x300062b2083e7c40), phy(0), device_name(0x5000cca29dc35e11)
scsi 18:0:0:0: enclosure logical id (0x300062b208097c40), slot(0)
scsi 18:0:0:0: enclosure level(0x0000), connector name( C0.0)
scsi 18:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
scsi 18:0:0:0: qdepth(32), tagged(1), scsi_level(7), cmd_que(1)
sd 18:0:0:0: Attached scsi generic sg2 type 20
sd 18:0:0:0: [sdc] Host-managed zoned block device
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b200 flags=0x0050]
mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b300 flags=0x0050]
mpt3sas_cm0: mpt3sas_ctl_pre_reset_handler: Releasing the trace buffer due to adapter reset.
mpt3sas_cm0 fault info from func: mpt3sas_base_make_ioc_ready
mpt3sas_cm0: fault_state(0x2666)!
mpt3sas_cm0: sending diag reset !!
mpt3sas_cm0: diag reset: SUCCESS
sd 18:0:0:0: [sdc] REPORT ZONES start lba 0 failed
sd 18:0:0:0: [sdc] REPORT ZONES: Result: hostbyte=DID_RESET driverbyte=DRIVER_OK
sd 18:0:0:0: [sdc] 0 4096-byte logical blocks: (0 B/0 B)
Avoid such issue by always mapping the buffer of REPORT ZONES commands
using DMA_BIDIRECTIONAL (read+write IOMMU mapping). This is done by
introducing the helper function _base_scsi_dma_map() and using this helper
in _base_build_sg_scmd() and _base_build_sg_scmd_ieee() instead of calling
directly scsi_dma_map().
Fixes: 471ef9d4e498 ("mpt3sas: Build MPI SGL LIST on GEN2 HBAs and IEEE SGL LIST on GEN3 HBAs")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240719073913.179559-3-dlemoal@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull block updates from Jens Axboe:
- NVMe updates via Keith:
- Device initialization memory leak fixes (Keith)
- More constants defined (Weiwen)
- Target debugfs support (Hannes)
- PCIe subsystem reset enhancements (Keith)
- Queue-depth multipath policy (Redhat and PureStorage)
- Implement get_unique_id (Christoph)
- Authentication error fixes (Gaosheng)
- MD updates via Song
- sync_action fix and refactoring (Yu Kuai)
- Various small fixes (Christoph Hellwig, Li Nan, and Ofir Gal, Yu
Kuai, Benjamin Marzinski, Christophe JAILLET, Yang Li)
- Fix loop detach/open race (Gulam)
- Fix lower control limit for blk-throttle (Yu)
- Add module descriptions to various drivers (Jeff)
- Add support for atomic writes for block devices, and statx reporting
for same. Includes SCSI and NVMe (John, Prasad, Alan)
- Add IO priority information to block trace points (Dongliang)
- Various zone improvements and tweaks (Damien)
- mq-deadline tag reservation improvements (Bart)
- Ignore direct reclaim swap writes in writeback throttling (Baokun)
- Block integrity improvements and fixes (Anuj)
- Add basic support for rust based block drivers. Has a dummy null_blk
variant for now (Andreas)
- Series converting driver settings to queue limits, and cleanups and
fixes related to that (Christoph)
- Cleanup for poking too deeply into the bvec internals, in preparation
for DMA mapping API changes (Christoph)
- Various minor tweaks and fixes (Jiapeng, John, Kanchan, Mikulas,
Ming, Zhu, Damien, Christophe, Chaitanya)
* tag 'for-6.11/block-20240710' of git://git.kernel.dk/linux: (206 commits)
floppy: add missing MODULE_DESCRIPTION() macro
loop: add missing MODULE_DESCRIPTION() macro
ublk_drv: add missing MODULE_DESCRIPTION() macro
xen/blkback: add missing MODULE_DESCRIPTION() macro
block/rnbd: Constify struct kobj_type
block: take offset into account in blk_bvec_map_sg again
block: fix get_max_segment_size() warning
loop: Don't bother validating blocksize
virtio_blk: Don't bother validating blocksize
null_blk: Don't bother validating blocksize
block: Validate logical block size in blk_validate_limits()
virtio_blk: Fix default logical block size fallback
nvmet-auth: fix nvmet_auth hash error handling
nvme: implement ->get_unique_id
block: pass a phys_addr_t to get_max_segment_size
block: add a bvec_phys helper
blk-lib: check for kill signal in ioctl BLKZEROOUT
block: limit the Write Zeroes to manually writing zeroes fallback
block: refacto blkdev_issue_zeroout
block: move read-only and supported checks into (__)blkdev_issue_zeroout
...
|
|
Setting QUEUE_FLAG_NOMERGES was added in commit d1b01d14b7ba ("scsi:
mpt3sas: Set NVMe device queue depth as 128") without any explanation.
Drivers should second guess the block layer merge decisions, so remove
the flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240627124926.512662-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three obvious driver fixes and two core fixes.
The two core fixes are to disable Command Duration Limits by default
to fix an inconsistency in SATA and some USB devices. The other is to
change the default read size for block zero to follow the device
preference (some USB bridges preferring 16 byte commands don't have a
translation for READ(10) and thus don't scan properly)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpi3mr: Fix ATA NCQ priority support
scsi: ufs: core: Quiesce request queues before checking pending cmds
scsi: core: Disable CDL by default
scsi: mpt3sas: Avoid test/set_bit() operating in non-allocated memory
scsi: sd: Use READ(16) when reading block zero on large capacity disks
|
|
The function mpi3mr_qcmd() of the mpi3mr driver is able to indicate to
the HBA if a read or write command directed at an ATA device should be
translated to an NCQ read/write command with the high prioiryt bit set
when the request uses the RT priority class and the user has enabled NCQ
priority through sysfs.
However, unlike the mpt3sas driver, the mpi3mr driver does not define
the sas_ncq_prio_supported and sas_ncq_prio_enable sysfs attributes, so
the ncq_prio_enable field of struct mpi3mr_sdev_priv_data is never
actually set and NCQ Priority cannot ever be used.
Fix this by defining these missing atributes to allow a user to check if
an ATA device supports NCQ priority and to enable/disable the use of NCQ
priority. To do this, lift the function scsih_ncq_prio_supp() out of the
mpt3sas driver and make it the generic SCSI SAS transport function
sas_ata_ncq_prio_supported(). Nothing in that function is hardware
specific, so this function can be used in both the mpt3sas driver and
the mpi3mr driver.
Reported-by: Scott McCoy <scott.mccoy@wdc.com>
Fixes: 023ab2a9b4ed ("scsi: mpi3mr: Add support for queue command processing")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240611083435.92961-1-dlemoal@kernel.org
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The core change is to detect unusually large number of VPD pages
(caused by device manufacturers having an endiannes issue) and reject
them rather than trying to parse a huge non-existent array.
The remaining fixes are in drivers the most user visible of which is
the ALUA state transition recognition (leads to intermittent I/O
errors in some situations otherwise)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: mcq: Fix error output and clean up ufshcd_mcq_abort()
scsi: core: Handle devices which return an unusually large VPD page count
scsi: mpt3sas: Add missing kerneldoc parameter descriptions
scsi: qedf: Set qed_slowpath_params to zero before use
scsi: qedf: Wait for stag work during unload
scsi: qedf: Don't process stag work during unload and recovery
scsi: sr: Fix unintentional arithmetic wraparound
scsi: core: alua: I/O errors for ALUA state transitions
scsi: mpi3mr: Use proper format specifier in mpi3mr_sas_port_add()
|
|
There is a potential out-of-bounds access when using test_bit() on a single
word. The test_bit() and set_bit() functions operate on long values, and
when testing or setting a single word, they can exceed the word
boundary. KASAN detects this issue and produces a dump:
BUG: KASAN: slab-out-of-bounds in _scsih_add_device.constprop.0 (./arch/x86/include/asm/bitops.h:60 ./include/asm-generic/bitops/instrumented-atomic.h:29 drivers/scsi/mpt3sas/mpt3sas_scsih.c:7331) mpt3sas
Write of size 8 at addr ffff8881d26e3c60 by task kworker/u1536:2/2965
For full log, please look at [1].
Make the allocation at least the size of sizeof(unsigned long) so that
set_bit() and test_bit() have sufficient room for read/write operations
without overwriting unallocated memory.
[1] Link: https://lore.kernel.org/all/ZkNcALr3W3KGYYJG@gmail.com/
Fixes: c696f7b83ede ("scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path")
Cc: stable@vger.kernel.org
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240605085530.499432-1-leitao@debian.org
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The prior strscpy() replacement of strncpy() here expected the
manufacture_reply strings to be NUL-terminated, but it is possible
they are not, as the code pattern here shows, e.g., edev->vendor_id
being exactly 1 character larger than manufacture_reply->vendor_id,
and the replaced strncpy() was copying only up to the size of the
source character array. Replace this with memtostr(), which is the
unambiguous way to convert a maybe not-NUL-terminated character array
into a NUL-terminated string.
Fixes: b7e9712a02e8 ("scsi: mpt3sas: Replace deprecated strncpy() with strscpy()")
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Marco Patalano <mpatalan@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240410023155.2100422-3-keescook@chromium.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Pull in remaining commits from 6.10/scsi-queue.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Skip E820 checks for MCFG ECAM regions for new (2016+) machines,
since there's no requirement to describe them in E820 and some
platforms require ECAM to work (Bjorn Helgaas)
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien
Le Moal)
- Remove last user and pci_enable_device_io() (Heiner Kallweit)
- Wait for Link Training==0 to avoid possible race (Ilpo Järvinen)
- Skip waiting for devices that have been disconnected while
suspended (Ilpo Järvinen)
- Clear Secondary Status errors after enumeration since Master Aborts
and Unsupported Request errors are an expected part of enumeration
(Vidya Sagar)
MSI:
- Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas)
Error handling:
- Mask Genesys GL975x SD host controller Replay Timer Timeout
correctable errors caused by a hardware defect; the errors cause
interrupts that prevent system suspend (Kai-Heng Feng)
- Fix EDR-related _DSM support, which previously evaluated revision 5
but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan)
ASPM:
- Simplify link state definitions and mask calculation (Ilpo
Järvinen)
Power management:
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS
apparently doesn't know how to put them back in D0 (Mario
Limonciello)
CXL:
- Support resetting CXL devices; special handling required because
CXL Ports mask Secondary Bus Reset by default (Dave Jiang)
DOE:
- Support DOE Discovery Version 2 (Alexey Kardashevskiy)
Endpoint framework:
- Set endpoint BAR to be 64-bit if the driver says that's all the
device supports, in addition to doing so if the size is >2GB
(Niklas Cassel)
- Simplify endpoint BAR allocation and setting interfaces (Niklas
Cassel)
Cadence PCIe controller driver:
- Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof
Kozlowski)
Cadence PCIe endpoint driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
Freescale Layerscape PCIe controller driver:
- Convert DT binding to YAML (Frank Li)
MediaTek MT7621 PCIe controller driver:
- Add DT binding missing 'reg' property for child Root Ports
(Krzysztof Kozlowski)
- Fix theoretical string truncation in PHY name (Sergio Paracuellos)
NVIDIA Tegra194 PCIe controller driver:
- Return success for endpoint probe instead of falling through to the
failure path (Vidya Sagar)
Renesas R-Car PCIe controller driver:
- Add DT binding missing IOMMU properties (Geert Uytterhoeven)
- Add DT binding R-Car V4H compatible for host and endpoint mode
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
- Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski)
- Set the Subsystem Vendor ID, which was previously zero because it
was masked incorrectly (Rick Wertenbroek)
Synopsys DesignWare PCIe controller driver:
- Restructure DBI register access to accommodate devices where this
requires Refclk to be active (Manivannan Sadhasivam)
- Remove the deinit() callback, which was only need by the
pcie-rcar-gen4, and do it directly in that driver (Manivannan
Sadhasivam)
- Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean
up things like eDMA (Manivannan Sadhasivam)
- Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel
to dw_pcie_ep_init() (Manivannan Sadhasivam)
- Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to
reflect the actual functionality (Manivannan Sadhasivam)
- Call dw_pcie_ep_init_registers() directly from all the glue
drivers, not just those that require active Refclk from the host
(Manivannan Sadhasivam)
- Remove the "core_init_notifier" flag, which was an obscure way for
glue drivers to indicate that they depend on Refclk from the host
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli)
- Add DT binding J722S SoC support (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Add DT binding missing num-viewport, phys and phy-name properties
(Jan Kiszka)
Miscellaneous:
- Constify and annotate with __ro_after_init (Heiner Kallweit)
- Convert DT bindings to YAML (Krzysztof Kozlowski)
- Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming
Zhou)"
* tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Do not wait for disconnected devices when resuming
x86/pci: Skip early E820 check for ECAM region
PCI: Remove unused pci_enable_device_io()
ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io()
PCI: Update pci_find_capability() stub return types
PCI: Remove PCI_IRQ_LEGACY
scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY
scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios
Revert "genirq/msi: Provide constants for PCI/IMS support"
Revert "x86/apic/msi: Enable PCI/IMS"
Revert "iommu/vt-d: Enable PCI/IMS"
Revert "iommu/amd: Enable PCI/IMS"
Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support"
...
|
|
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-26-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add missing kerneldoc parameter descriptions to _scsih_set_debug_level().
Signed-off-by: Deming Wang <wangdeming@inspur.com>
Link: https://lore.kernel.org/r/20240513115956.1576-1-wangdeming@inspur.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Switch to the ->device_configure method instead of ->slave_configure and
update the block limits on the passed in queue_limits instead of using the
per-limit accessors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-13-hch@lst.de
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Justin Stitt <justinstitt@google.com> says:
This series contains multiple replacements of strncpy throughout the
scsi subsystem.
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces. The details of each replacement will be in their
respective patch.
Link: https://lore.kernel.org/r/20240305-strncpy-drivers-scsi-mpi3mr-mpi3mr_fw-c-v3-0-5b78a13ff984@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"Only a couple of driver updates this time (lpfc and mpt3sas) plus the
usual assorted minor fixes and updates. The major core update is a set
of patches moving retries out of the drivers and into the core"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (84 commits)
scsi: core: Constify the struct device_type usage
scsi: libfc: replace deprecated strncpy() with memcpy()
scsi: lpfc: Replace deprecated strncpy() with strscpy()
scsi: bfa: Fix function pointer type mismatch for state machines
scsi: bfa: Fix function pointer type mismatch for hcb_qe->cbfn
scsi: bfa: Remove additional unnecessary struct declarations
scsi: csiostor: Avoid function pointer casts
scsi: qla1280: Remove redundant assignment to variable 'mr'
scsi: core: Make scsi_bus_type const
scsi: core: Really include kunit tests with SCSI_LIB_KUNIT_TEST
scsi: target: tcm_loop: Make tcm_loop_lld_bus const
scsi: scsi_debug: Make pseudo_lld_bus const
scsi: iscsi: Make iscsi_flashnode_bus const
scsi: fcoe: Make fcoe_bus_type const
scsi: lpfc: Copyright updates for 14.4.0.0 patches
scsi: lpfc: Update lpfc version to 14.4.0.0
scsi: lpfc: Change lpfc_vport load_flag member into a bitmask
scsi: lpfc: Change lpfc_vport fc_flag member into a bitmask
scsi: lpfc: Protect vport fc_nodes list with an explicit spin lock
scsi: lpfc: Change nlp state statistic counters into atomic_t
...
|
|
The replacement in mpt3sas_base.c is a trivial one because desc is already
zero-initialized meaning there is no functional change here.
For mpt3sas_transport.c, we know edev is zero-initialized as well while
manufacture_reply comes from dma_alloc_coherent(). No functional change
here either.
For all cases, use the more idiomatic strscpy() usage of: strscpy(dest,
src, sizeof(dest))
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/r/20240305-strncpy-drivers-scsi-mpi3mr-mpi3mr_fw-c-v3-2-5b78a13ff984@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If the driver detects that the controller is not ready before sending the
first IOC facts command, it will wait for a maximum of 10 seconds for it to
become ready. However, even if the controller becomes ready within 10
seconds, the driver will still issue a diagnostic reset.
Modify the driver to avoid sending a diag reset if the controller becomes
ready within the 10-second wait time.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240221071724.14986-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update driver version to 48.100.00.00.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20231228114810.11923-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add a new IOCTL command MPT3ENABLEDIAGSBRRELOAD. As a part of firmware
update operation, applications use this IOCTL command to set the SBR reload
bit in the Host Diagnostic register. This permits HBA firmware to be
updated without powercycling the system.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312280909.MZyhxwBL-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202312281141.jDyPezRn-lkp@intel.com/
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20231228114810.11923-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
