| Age | Commit message (Collapse) | Author |
|---|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20240903023754.493568-1-nichen@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tty_port::close_delay and ::closing_wait are set in tty_port_init() few
lines above already, no need to reset them (to the same values).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240808103549.429349-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The comment mentions ISA removed long time ago. It also comments on
.driver_data pointing to above structures. That is not true either.
Remove that.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240808103549.429349-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Work for __counted_by on generic pointers in structures (not just
flexible array members) has started landing in Clang 19 (current tip of
tree). During the development of this feature, a restriction was added
to __counted_by to prevent the flexible array member's element type from
including a flexible array member itself such as:
struct foo {
int count;
char buf[];
};
struct bar {
int count;
struct foo data[] __counted_by(count);
};
because the size of data cannot be calculated with the standard array
size formula:
sizeof(struct foo) * count
This restriction was downgraded to a warning but due to CONFIG_WERROR,
it can still break the build. The application of __counted_by on the
ports member of 'struct mxser_board' triggers this restriction,
resulting in:
drivers/tty/mxser.c:291:2: error: 'counted_by' should not be applied to an array with element of unknown size because 'struct mxser_port' is a struct type with a flexible array member. This will be an error in a future compiler version [-Werror,-Wbounds-safety-counted-by-elt-type-unknown-size]
291 | struct mxser_port ports[] __counted_by(nports);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
Remove this use of __counted_by to fix the warning/error. However,
rather than remove it altogether, leave it commented, as it may be
possible to support this in future compiler releases.
Cc: <stable@vger.kernel.org>
Closes: https://github.com/ClangBuiltLinux/linux/issues/2026
Fixes: f34907ecca71 ("mxser: Annotate struct mxser_board with __counted_by")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240529-drop-counted-by-ports-mxser-board-v1-1-0ab217f4da6d@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Switch character types to u8 and sizes to size_t. To conform to
characters/sizes in the rest of the tty layer.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20231206073712.17776-19-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct mxser_board.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175245.work.196-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unify with the rest of the code. Use size_t for counts and ssize_t for
retval.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-30-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Data are now typed as u8. Propagate this change to
tty_operations::put_char().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Link: https://lore.kernel.org/r/20230810091510.13006-29-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Data are now typed as u8. Propagate this change to
tty_operations::write().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20230810091510.13006-28-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
hw_stopped in tty_struct is used like bool, convert the variable type
to bool.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Link: https://lore.kernel.org/r/20230309082035.14880-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert various parameter names for ->dtr_rts() and related functions
from onoff, on, and raise to active.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-12-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert the raise/on parameter in ->dtr_rts() to bool through the
callchain. The parameter is used like bool. In USB serial, there
remains a few implicit bool -> larger type conversions because some
devices use u8 in their control messages.
In moxa_tiocmget(), dtr variable was reused for line status which
requires int so use a separate variable for status.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Return boolean from ->carrier_raised() instead of 0 and 1. Make the
return type change also to tty_port_carrier_raised() that makes the
->carrier_raised() call (+ cd variable in moxa into which its return
value is stored).
Also cleans up a few unnecessary constructs related to this change:
return xx ? 1 : 0;
-> return xx;
if (xx)
return 1;
return 0;
-> return xx;
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make callers pass true/false consistently for bool val.
Reviewed-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable hwid is assigned a value but it is never read. The
assignment is redundant and can be removed.
Cleans up clang scan build warning:
drivers/tty/mxser.c:401:7: warning: Although the value stored to 'hwid'
is used in the enclosing expression, the value is never actually read
from 'hwid' [deadcode.DeadStores]
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220730130925.150018-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
BOTHER is defined by all architectures since commit d0ffb805b729
("arch/alpha, termios: implement BOTHER, IBSHIFT and termios2").
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220513082906.11096-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Having a generic UART_LCR_WLEN() macro and the tty_get_char_size()
helper, we can remove all those repeated switch-cases in drivers.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224095558.30929-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use kfifo for xmit buffer handling. The change is mostly
straightforward. It saves complexity both on the stuffing side
(mxser_write() and mxser_put_char()) and pulling side
(mxser_transmit_chars()). In fact, the loop in mxser_write() can be
completely deleted as the wrap of the buffer is taken care of in the
kfifo code now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220124071430.14907-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For the mxser driver to use kfifo, use tty_port_alloc_xmit_buf() and
tty_port_free_xmit_buf() helpers in activate/shutdown, respectively.
As these calls have to be done in a non-atomic context, we have to move
them outside spinlock and make sure irq is really stopped after we write
to the ISR register.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220124071430.14907-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When LSR is 0xff in ->activate() (rather unlike), we return an error.
Provided ->shutdown() is not called when ->activate() fails, nothing
actually frees the buffer in this case.
Fix this by properly freeing the buffer in a designated label. We jump
there also from the "!info->type" if now too.
Fixes: 6769140d3047 ("tty: mxser: use the tty_port_open method")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220124071430.14907-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that we have all the PCI device IDs unified, we can use
PCI_DEVICE_DATA() macro to simplify mxser's pci_device_id list, i.e.
mxser_pcibrds.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-20-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no point having MOXA PCI device IDs in include/linux/pci_ids.h.
Move them to the driver and sort them all by the ID.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-19-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some of the MOXA PCI device IDs contain _MOXA_, some don't. Add it to
the latter, so that they are all unified.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-18-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mxser doesn't increase port->icount.buf_overrun at all. Do so if overrun
happens, so that it can be read from the stats.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-17-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After the previous change (no plays with of tty->receive_room), the tty
parameter is unused.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-16-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
First, checking tty->receive_room to signalize whether there is enough space
in the tty buffers does not make much sense. Provided the tty buffers
are in tty_port and those are not checked at all.
Second, if the rx path is throttled, with CRTSCTS, RTS is deasserted,
but is never asserted again. This leads to port "lockup", not accepting
any more input.
So:
1) stty -F /dev/ttyMI0 crtscts # the mxser port
2) stty -F /dev/ttyS6 crtscts # the connected port
3) cat /dev/ttyMI0
4) "write in a loop" to /dev/ttyS6
5) cat from 3) produces the bytes from 4)
6) killall -STOP cat (the 3)'s one)
7) wait for RTS to drop on /dev/ttyMI0
8) killall -CONT cat (again the 3)'s one)
cat erroneously produces no more output now (i.e. no data sent from
ttyS6 to ttyMI can be seen).
Note that the step 7) is performed twice: once from n_tty by
tty_throttle_safe(), once by mxser_stoprx() from the receive path. Then
after step 7), n_tty correctly unthrottles the input, but mxser calls
mxser_stoprx() again as there is still only a little space in n_tty
buffers (tty->receive_room mentioned at the beginning), but the device's
FIFO is/can be already filled.
After this patch, the output is correctly resumed, i.e. n_tty both
throttles and unthrottles without interfering with mxser's attempts.
This allows us to get rid of the non-standard ldisc_stop_rx flag from
struct mxser_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-15-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
timeout cannot be zero at the point of use. So no need to check for
zero. Also precompute the expiration time (into expire) and use it. This
makes the code more clear.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-14-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of schedule_timeout_interruptible(), because:
1) we don't have to bother with the task state, and
2) msleep* guarantees to sleep that time (if not interrupted).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-13-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
And move it to new mxser_tx_empty(), because:
1) it simplifies the code (esp. the locking), and
2) serial_core needs such a hook anyway, so have it ready.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-12-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Finally, the mxser_close() code in is mostly identical to
tty_port_close(), so replace the code by a single call to the function.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
I fail to see the point of calling mxser_flush_buffer() from
mxser_close():
1) The SW xmit buffer is freed in mxser_shutdown_port() right after the
call to mxser_flush_buffer(). And all 'cnt', 'head', and 'tail' are
properly initialized to 0 in mxser_activate().
2) The HW buffer is flushed in mxser_shutdown_port() via
mxser_disable_and_clear_FIFO() too.
So the effect of doing it by mxser_flush_buffer() in mxser_close() is
none. Hence remove it, so that when we use tty_port_close() later, the
code is 1:1 identical.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mxser_stop_rx() should be called from mxser_shutdown_port() for several
reasons:
1) info->slock is held while manipulating IER (as on other places),
2) hangup now stops rx too,
3) mxser_close() will use tty_port_close() and there is no place except
tty_port_operations::shutdown() where this can be done,
4) this is the same sequence as serial_core does. So we can map this
code 1:1 when switching the driver to it.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Noone sets tty->driver_data to NULL in the driver, so there is no point
to check that in mxser_close(). Remove the check.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xmit_buf is supposed to exist in all these functions. I.e. from
tty_port_operations::activate() to ::shutdown(). So remove these checks.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The port->icount.tx is handled in a too complicated manner. Instead of
remembering the original count and subtracting the new one from it,
simply increase tx for each character in the loop. No need for cnt
variable then.
Change also the "X = X & Y" assignment to simpler "X &= Y".
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The MSR read is currently performed on both places where
mxser_check_modem_status() is called. So move it there to avoid code
duplication.
Rename the variable to msr while we move it, to actually see what
"status" we are testing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The others are superfluous with tty refcounting in place now. And they
are racy in fact:
* tty_port_initialized() reports false for a small moment after
interrupts are enabled.
* closing is 1 while the port is still alive.
The queues are flushed later during close anyway. So there is no need
for this special handling. Actually, the ISR should not flush the
queues. It should behave as every other driver, just queue the chars
into tty buffer and go on. But this will be changed later. There is
still a lot code depending on having tty in ISR (and not only tty_port).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As it is the only thing it does now. This is one of the future
serial_core hooks.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mxser_close() behaves like this:
-> tty_port_close_start()
-> tty_wait_until_sent()
-> mxser_wait_until_sent()
-> mxser_close_port
-> wait for TEMT
So it is already waited for TEMT through mxser_wait_until_sent() and
there is another round of waiting in mxser_close_port(). The latter one
is superfluous as nothing could be filled into the output FIFO. Remove
the call.
This helps unification among drivers (so that all behave the same) and
future use of tty_port_close().
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We force the FCR contents on many places in the code instead of writing
what was actually set in mxser_change_speed() (by ->activate() or
->set_serial_info()).
So introduce mxser_port::FCR to hold the proper contents and bitwise-OR
the value to what needs to be set on all those locations. That is,
clearing RX and/or TX FIFOs. Those flags are self-clearing, so no need
to set them to mxser_port::FCR.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The UART_FCR register is write-only. When reading it, one gets contents
of (read-only) UART_IIR instead as they are shared. This mistake was
performed in mxser_flush_buffer() to clear FIFOs.
Actually FCR handling throughout the driver is completely broken. On
many places, it respects neither mu860 settings, nor FIFO (16450 vs
16550) setting. This patch doesn't help to fix this, it actually does
the same. We will introduce a mxser_port::FCR in the next patch to fix
this issue.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This code is used on two places, make a helper for disabling and
clearing FIFOs. And demangle the too complicated 'if' by using a local
variable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Provided FIFO is always enabled for MUST chips, move its FCR setting out
of PORT_8250/PORT_16450 special case in mxser_change_speed(). Now, we
can pre-set fcr to zero and invert the condition of the 'if'.
This makes the code more readable (no functional change intended).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's used only as a yes-no variable, so make it a bool and switch the
set values appropriately.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mxser_receive_chars_old() is used whenever MOXA_MUST_LSR_RERR is set in
status no matter the HW ID (the last 'if'). So there is no need for
another check of MOXA_MUST_LSR_RERR _with_ hwid == MOXA_MUST_MU860_HWID
(the third 'if'). Hence remove this subcase. That allows us to check
status on a single line with both UART_LSR_BRK_ERROR_BITS (from the
second 'if') and MOXA_MUST_LSR_RERR (the last 'if').
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a user tries to set a too high rate, it fails due to check in
mxser_set_baud(). But the high rate remains set in termios, so the user
might think everything went smooth. Restore the baud rate from the
old_termios if this happens, so that user knows nothing was changed in
fact.
It used to behave the correct way many years ago, but somehow the
restoration vanished with commit 1c45607ad3eb (Char: mxser, remove it)
-- the commit removed mxser's older clone.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This code works, but it's cleaner to use semi-colons at the end of
a statement instead of a comma.
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20210825072435.GB13013@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need
for two exported identical functions, therefore switch all users of
old put_tty_driver() to new tty_driver_kref_put() and remove the former
for good.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
alloc_tty_driver was deprecated by tty_alloc_driver in commit
7f0bc6a68ed9 (TTY: pass flags to alloc_tty_driver) in 2012.
I never got into eliminating alloc_tty_driver until now. So we still
have two functions for allocating drivers which might be confusing. So
get rid of alloc_tty_driver uses to eliminate it for good in the next
patch.
Note we need to switch return value checking as tty_alloc_driver uses
ERR_PTR. And flags are now a parameter of tty_alloc_driver.
Cc: Richard Henderson <rth@twiddle.net>(odd fixer:ALPHA PORT)
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
