| Age | Commit message (Collapse) | Author |
|---|
|
startup()/shutdown() callbacks access SIFIVE_SERIAL_IE_OFFS.
The register is also accessed from write() callback.
If console were printing and startup()/shutdown() callback
gets called, its access to the register could be overwritten.
Add port->lock to startup()/shutdown() callbacks to make sure
their access to SIFIVE_SERIAL_IE_OFFS is synchronized against
write() callback.
Fixes: 45c054d0815b ("tty: serial: add driver for the SiFive UART")
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Rule: add
Link: https://lore.kernel.org/stable/20250330003522.386632-1-ryotkkr98%40gmail.com
Link: https://lore.kernel.org/r/20250412001847.183221-1-ryotkkr98@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The MSM UART DM controller supports different working modes, e.g. DMA or
the "single-character mode", where all reads/writes operate on a single
character rather than 4 chars (32-bit) at once. When using earlycon,
__msm_console_write() always writes 4 characters at a time, but we don't
know which mode the bootloader was using and we don't set the mode either.
This causes garbled output if the bootloader was using the single-character
mode, because only every 4th character appears in the serial console, e.g.
"[ 00oni pi 000xf0[ 00i s 5rm9(l)l s 1 1 SPMTA 7:C 5[ 00A ade k d[
00ano:ameoi .Q1B[ 00ac _idaM00080oo'"
If the bootloader was using the DMA ("DM") mode, output would likely fail
entirely. Later, when the full serial driver probes, the port is
re-initialized and output works as expected.
Fix this also for earlycon by clearing the DMEN register and
reset+re-enable the transmitter to apply the change. This ensures the
transmitter is in the expected state before writing any output.
Cc: stable <stable@kernel.org>
Fixes: 0efe72963409 ("tty: serial: msm: Add earlycon support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250408-msm-serial-earlycon-v1-1-429080127530@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.15-rc1.
Include in here are the following:
- more great tty layer cleanups from Jiri. Someday this will be done,
but that's not going to be any year soon...
- kdb debug driver reverts to fix a reported issue
- lots of .dts binding updates for different devices with serial
devices
- lots of tiny updates and tweaks and a few bugfixes for different
serial drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
tty: serial: fsl_lpuart: Fix unused variable 'sport' build warning
serial: stm32: do not deassert RS485 RTS GPIO prematurely
serial: 8250: add driver for NI UARTs
dt-bindings: serial: snps-dw-apb-uart: document RZ/N1 binding without DMA
serial: icom: fix code format problems
serial: sh-sci: Save and restore more registers
tty: serial: pl011: remove incorrect of_match_ptr annotation
dt-bindings: serial: snps-dw-apb-uart: Add support for rk3562
tty: serial: lpuart: only disable CTS instead of overwriting the whole UARTMODIR register
tty: caif: removed unused function debugfs_tx()
serial: 8250_dma: terminate correct DMA in tx_dma_flush()
tty: serial: fsl_lpuart: rename register variables more specifically
tty: serial: fsl_lpuart: use port struct directly to simply code
tty: serial: fsl_lpuart: Use u32 and u8 for register variables
tty: serial: fsl_lpuart: disable transmitter before changing RS485 related registers
tty: serial: 8250: Add Brainboxes XC devices
dt-bindings: serial: fsl-lpuart: support i.MX94
tty: serial: 8250: Add some more device IDs
dt-bindings: serial: samsung: add exynos7870-uart compatible
serial: 8250_dw: Comment possible corner cases in serial_out() implementation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- New option "printk.debug_non_panic_cpus" allows to store printk
messages from non-panic CPUs during panic. It might be useful when
panic() fails. It is disabled by default because it increases the
chance to see the messages printed before panic() and on the
panic-CPU.
- New build option "CONFIG_NULL_TTY_DEFAULT_CONSOLE" allows to build
kernel without the virtual terminal support which prefers ttynull
over serial console.
- Do not unblank suspended consoles.
- Some code clean up.
* tag 'printk-for-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk/panic: Add option to allow non-panic CPUs to write to the ring buffer.
printk: Add an option to allow ttynull to be a default console device
printk: Check CON_SUSPEND when unblanking a console
printk: Rename console_start to console_resume
printk: Rename console_stop to console_suspend
printk: Rename resume_console to console_resume_all
printk: Rename suspend_console to console_suspend_all
|
|
Remove the unused variable 'sport' to avoid the kernel build warning.
Fixes: 3cc16ae096f1 ("tty: serial: fsl_lpuart: use port struct directly to simply code")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202503210614.2qGlnbIq-lkp@intel.com/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20250324021051.162676-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If stm32_usart_start_tx is called with an empty xmit buffer, RTS GPIO
could be deasserted prematurely, as bytes in TX FIFO are still
transmitting.
So this patch remove rts disable when xmit buffer is empty.
Fixes: d7c76716169d ("serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Cheick Traore <cheick.traore@foss.st.com>
Link: https://lore.kernel.org/r/20250320152540.709091-1-cheick.traore@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The National Instruments (NI) 16550 is a 16550-like UART with larger
FIFOs and embedded RS-232/RS-485 transceiver control circuitry. This
patch adds a driver that can operate this UART, which is used for
onboard serial ports in several NI embedded controller designs.
Portions of this driver were originally written by Jaeden Amero and
Karthik Manamcheri, with extensive cleanups and refactors since by
Brenda Streiff.
Cc: Gratian Crisan <gratian.crisan@emerson.com>
Co-developed-by: Jason Smith <jason.smith@emerson.com>
Signed-off-by: Jason Smith <jason.smith@emerson.com>
Signed-off-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/a3b0df6d-1dd5-4cc4-a7e1-4ed51fb9e4cc@emerson.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix below inconsistent indenting smatch warning.
smatch warnings:
drivers/tty/serial/icom.c:1768 icom_probe() warn: inconsistent indenting
Removed that useless (void *), the code would fit on a single 100c line
Removed '{' and '}'.
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/r/20250305095120.7518-1-hanchunchao@inspur.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On (H)SCIF with a Baud Rate Generator for External Clock (BRG), there
are multiple ways to configure the requested serial speed. If firmware
uses a different method than Linux, and if any debug info is printed
after the Bit Rate Register (SCBRR) is restored, but before termios is
reconfigured (which configures the alternative method), the system may
lock-up during resume.
Fix this by saving and restoring the contents of the BRG Frequency
Division (SCDL) and Clock Select (SCCKS) registers as well.
Also save and restore the HSCIF's Sampling Rate Register (HSSRR), which
configures the sampling point, and the SCIFA/SCIFB's Serial Port Control
and Data Registers (SCPCR/SCPDR), which configure the optional control
flow signals.
After this, all registers that are not saved/restored are either:
- read-only,
- write-only,
- status registers containing flags with clear-after-set semantics,
- FIFO Data Count Trigger registers, which do not matter much for
the serial console.
Fixes: 22a6984c5b5df8ea ("serial: sh-sci: Update the suspend/resume support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/11c2eab45d48211e75d8b8202cce60400880fe55.1741114989.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Building with W=1 shows a warning about sbsa_uart_of_match being unused when
CONFIG_OF is disabled:
drivers/tty/serial/amba-pl011.c:2945:34: error: unused variable 'sbsa_uart_of_match' [-Werror,-Wunused-const-variable]
The driver is not actually used on any machines that are built
with CONFIG_OF disabled, so using of_match_ptr() won't save any
actual memory, and it can be best removed.
The corresponding ACPI_PTR() annotation does save a few bytes on
32-bit arm since CONFIG_ACPI is not available, but for consistency
it seems better to remove both along with the __maybe_unused
annotation on the ACPI table.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250225163556.4169086-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UARTMODIR register
No need to overwrite the whole UARTMODIR register before waiting the
transmit engine complete, actually our target here is only to disable
CTS flow control to avoid the dirty data in TX FIFO may block the
transmit engine complete.
Also delete the following duplicate CTS disable configuration.
Fixes: d5a2e0834364 ("tty: serial: lpuart: disable flow control while waiting for the transmit engine to complete")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20250307065446.1122482-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When flushing transmit side DMA, it is the transmit channel that should
be terminated, not the receive channel.
Fixes: 9e512eaaf8f40 ("serial: 8250: Fix fifo underflow on flush")
Cc: stable <stable@kernel.org>
Reported-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250224121831.1429323-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are many fuzzy register variables in the lpuart driver, such as
temp, tmp, val, reg. Let's give these register variables more specific
names.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20250312023904.1343351-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Most lpuart functions have the parameter struct uart_port *port, but
still use the &sport->port to get the uart_port instead of use it
directly, let's simply the code logic, directly use this struct instead
of covert it from struct sport.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20250312023904.1343351-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use u32 and u8 rather than unsigned long or unsigned char for register
variables for clarity and consistency.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20250312023904.1343351-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
registers
According to the LPUART reference manual, TXRTSE and TXRTSPOL of MODIR
register only can be changed when the transmitter is disabled.
So disable the transmitter before changing RS485 related registers and
re-enable it after the change is done.
Fixes: 67b01837861c ("tty: serial: lpuart: Add RS485 support for 32-bit uart flavour")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250312022503.1342990-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These ExpressCard devices use the OxPCIE chip and can be used with
this driver.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/DB7PR02MB3802907A9360F27F6CD67AAFC4D62@DB7PR02MB3802.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These card IDs got missed the first time around.
Cc: stable <stable@kernel.org>
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DB7PR02MB380295BCC879CCF91315AC38C4C12@DB7PR02MB3802.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
8250 DesignWare driver uses a few custom implementations of the serial_out().
These implementations are carefully made to avoid infinite loops. But this is
not obvious from looking at the code. Comment the possible corner cases in
the respective functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250317094021.1201512-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
change_irq and change_port are boolean variables. Mark them as such
(instead of uint).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-32-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Return immediately from the error locations or switch-case ends. It is
therefore easier to see the flow.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-31-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is unnecessary here and makes the code harder to follow. Invert the
condition and drop the goto+label.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-30-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
* Use already defined 'port' for fetching start/offset, and size.
* Return from the switch immediately -- so it is clear what is returned
and when.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-29-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are serial_port_in/out() helpers to be used instead of direct
p->serial_in/out(). Use them in various 8250 drivers.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: "Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
--
[v2]
* Use serial_port_in/out() and not serial_in/out() [Andy]
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # 8250_dw
Link: https://lore.kernel.org/r/20250317070046.24386-28-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uart_line_info() wants to work with struct uart_state. Do not pass a
driver and an index. Pass the precomputed struct directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-27-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The linking is done implicitly by tty_port_register_device_attr_serdev()
few lines below. So drop this explicit tty_port_link_device().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-26-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is commented and never used.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Link: https://lore.kernel.org/r/20250317070046.24386-25-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
They are simple wrappers around serial_{in/out}() without actually
pausing the execution. Since ever. So drop these useless wrappers.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Link: https://lore.kernel.org/r/20250317070046.24386-24-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The intent of console_start was to resume a previously suspended console,
so rename it accordingly.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20250226-printk-renaming-v1-4-0b878577f2e6@suse.com
[pmladek@suse.com: Fixed typo in the commit message. Updated also new drm_log.c.]
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
The intent of console_stop was in fact to suspend it, so rename the
function accordingly.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20250226-printk-renaming-v1-3-0b878577f2e6@suse.com
[pmladek@suse.com: Fixed typo in the commit message. Updated also new drm_log.c]
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/4a028a23126b3350a5e243dcb49e1ef1b2a4b740.1738746904.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/c21664d013015584aebbb6bb8cedd748182cb551.1738746904.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/ad27070bc67c13f8a9acbd5cbf4cbae72797e3e1.1738746904.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/78e8c0d1b38998eab983fad265751ed13c2b9009.1738746904.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/991926d130cc272df30d226760d5d74187991669.1738746904.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The field 'function' of struct hrtimer should not be changed directly, as
the write is lockless and a concurrent timer expiry might end up using the
wrong function pointer.
Switch to use hrtimer_update_function() which also performs runtime checks
that it is safe to modify the callback.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/af7823518fb060c6c97105a2513cfc61adbdf38f.1738746927.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The following splat has been observed on a SAMA5D27 platform using
atmel_serial:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:738
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74
Hardware name: Atmel SAMA5
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x44/0x70
dump_stack_lvl from __might_resched+0x38c/0x598
__might_resched from disable_irq+0x1c/0x48
disable_irq from mctrl_gpio_disable_ms+0x74/0xc0
mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4
atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8
atmel_set_termios from uart_change_line_settings+0x15c/0x994
uart_change_line_settings from uart_set_termios+0x2b0/0x668
uart_set_termios from tty_set_termios+0x600/0x8ec
tty_set_termios from ttyport_set_flow_control+0x188/0x1e0
ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc]
wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth]
hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth]
hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth]
hci_power_on [bluetooth] from process_one_work+0x998/0x1a38
process_one_work from worker_thread+0x6e0/0xfb4
worker_thread from kthread+0x3d4/0x484
kthread from ret_from_fork+0x14/0x28
This warning is emitted when trying to toggle, at the highest level,
some flow control (with serdev_device_set_flow_control) in a device
driver. At the lowest level, the atmel_serial driver is using
serial_mctrl_gpio lib to enable/disable the corresponding IRQs
accordingly. The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to
disable_irq (called in mctrl_gpio_disable_ms) being possibly called in
some atomic context (some tty drivers perform modem lines configuration
in regions protected by port lock).
Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one
and a blocking one. Replace mctrl_gpio_disable_ms calls with the
relevant version depending on whether the call is protected by some port
lock.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Richard Genoud <richard.genoud@bootlin.com>
Link: https://lore.kernel.org/r/20250217-atomic_sleep_mctrl_serial_gpio-v3-1-59324b313eef@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The field 'function' of struct hrtimer should not be changed directly, as
the write is lockless and a concurrent timer expiry might end up using the
wrong function pointer.
Switch to use hrtimer_update_function() which also performs runtime checks
that it is safe to modify the callback.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/af7823518fb060c6c97105a2513cfc61adbdf38f.1738746927.git.namcao@linutronix.de
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/4a028a23126b3350a5e243dcb49e1ef1b2a4b740.1738746904.git.namcao@linutronix.de
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/c21664d013015584aebbb6bb8cedd748182cb551.1738746904.git.namcao@linutronix.de
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/ad27070bc67c13f8a9acbd5cbf4cbae72797e3e1.1738746904.git.namcao@linutronix.de
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/78e8c0d1b38998eab983fad265751ed13c2b9009.1738746904.git.namcao@linutronix.de
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/991926d130cc272df30d226760d5d74187991669.1738746904.git.namcao@linutronix.de
|
|
We need the tty changes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Tegra264 SoC supports the UART Trace Controller (UTC), which allows
multiple firmware clients (up to 16) to share a single physical UART.
Each client is provided with its own interrupt and has access to a
128-character wide FIFO for both transmit (TX) and receive (RX)
operations.
Add tegra-utc driver to support Tegra UART Trace Controller (UTC)
client.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213125612.4705-3-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 0c57dfcc6c1d037243c2f8fbf62eab3633326ec0.
The functionality was supoosed to be used by a later patch in the
series that never landed [1]. Drop it.
NOTE: part of functionality was already reverted by commit
39d0be87438a ("serial: kgdb_nmi: Remove unused knock code"). Also note
that this revert is not a clean revert given code changes that have
happened in the meantime.
It's obvious that nobody is using this code since the two exposed
functions (kgdb_register_nmi_console() and
kgdb_unregister_nmi_console()) are both no-ops if
"arch_kgdb_ops.enable_nmi" is not defined. No architectures define it.
[1] https://lore.kernel.org/lkml/1348522080-32629-9-git-send-email-anton.vorontsov@linaro.org/
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: URL [1]
Link: https://lore.kernel.org/r/20250129082535.1.Ia095eac1ae357f87d23e7af2206741f5d40788f1@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Not all the cases provide the driver data, that is represented by
an object instance of struct dw8250_platform_data. Id est the change
missed the case when the driver is instantiated via board files as
pure platform driver. Fix this by calling dw8250_quirks() conditionally.
This will require splitting dw8250_setup_dma_filter() out of dw8250_quirks().
Also make sure IRQ handler won't crash, it also requires driver data
to be present.
Fixes: bfd3d4a40f39 ("serial: 8250_dw: Drop unneeded NULL checks in dw8250_quirks()")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202502121529.f7e65d49-lkp@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250212115952.2312444-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Renesas RZ/G3S supports a power saving mode where power to most of the
SoC components is turned off. When returning from this power saving mode,
SoC components need to be re-configured.
The SCIFs on the Renesas RZ/G3S need to be re-configured as well when
returning from this power saving mode. The sh-sci code already configures
the SCIF clocks, power domain and registers by calling uart_resume_port()
in sci_resume(). On suspend path the SCIF UART ports are suspended
accordingly (by calling uart_suspend_port() in sci_suspend()). The only
missing setting is the reset signal. For this assert/de-assert the reset
signal on driver suspend/resume.
In case the no_console_suspend is specified by the user, the registers need
to be saved on suspend path and restore on resume path. To do this the
sci_console_save()/sci_console_restore() functions were added. There is no
need to cache/restore the status or FIFO registers. Only the control
registers. The registers that will be saved/restored on suspend/resume are
specified by the struct sci_suspend_regs data structure.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250207113313.545432-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SoCs like the i.MX93 have several lpuart interfaces, but fsl_lpuart
uses the driver name to request the IRQ. This makes it hard to
identify interfaces from outputs like /proc/interrupts .
So use the dev_name() for requesting instead.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20250205091007.4528-1-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
